LabVIEW openings at Noida for Sankalp Semiconductor

JOB Description :
Technical Requirements: (in order of importance)
· Mandatory
o Prior Experience : 2-4 yrs
o Experience with labview and teststand
o Experience of GUI programming through labview for encoding the measurement procedures for atleast one analog interface (ADC/PLL/Power blocks)
o Experience of performing automation of measurement instruments like signal generators, oscilloscopes, power supplies etc.
o Familiarity with programming of NI hardware DAQs/protocols (GPIB, PCI, PXI)
· Good to have
o Block level understanding of circuits like LDOs, DC-DC converters etc.
o Experience of board bringup and debug.

Hello Sir/ Madam,
I am interested in doing work at Sankalp Semiconductor as a LabVIEW engineer.
I am CLAD (Certified LabVIEW Associate Developer) and have relevant experience..!!
Attached my Resume..!!
Attachments:
Aman Singhla Resume.pdf ‏445 KB

Similar Messages

How to obtain the table index in word use LabVIEW Report Generation Toolkit for Microsoft Office

I created a word templete and it had several tables. When I use the "Word Edit Cell" function in LabVIEW Report Generation Toolkit for Microsoft Office, the function need "table index", and I didn't find any function to get or set the table index in word document. How can I achieve my attention to write value to specified table cell using the "Word Edit Cell" function?
Thanks for reply!
YangAfreet

Hi yangafreet
You do not need to get the table index for the word edit cell.vi from anywhere. LabVIEW will automatically index all the tables in the document. See the attatched vi for an example.
Rich
Attachments:
Table Edit.vi ‏23 KB

LabVIEW Report Generation Toolkit for Microsoft Office

Hi!
One question. I have bought the LabVIEW Report Generation Toolkit for Microsoft Office
Version 1.0a and am trying to install it under Labview 7.1 but the installation stops with the error: "you need a Labview Version 6.0 runtime engine." Is there any possibility to install the toolkit anyway?
Regards
Stefan

Hi
You can try to update your Version 1.0 to Version 1.0.1. Then it should be working.
Here ist the link for the free update:
http://digital.ni.com/softlib.nsf/websearch/19003CF70BB8A57186256E5A00672E2A?opendocument
if it not works you can try to install the runtime engine 6.0 on your system. her is the link:
http://digital.ni.com/softlib.nsf/websearch/D5F11A64A905DB27862569EC005E31E2?opendocument&node=132070_US
Regards
Manuel

How do I put data into a template using the Labview report generation toolkit for Microsoft Office?

I am running Lookout 5.0 and have recently purchased the Labview Report Generation Toolkit for Microsoft Office to create reports from my Lookout logged data. Since I have never used Labview I am having my problems. I tried following the tutorials but they do not seem to be examples of what I want to do.
I log rainfall totals (1 spreadsheet)in Lookout from 40 different sites in 5 minute increments. I copy these totals and paste them into another spreadsheet which sums them up to give me hourly totals and then paste those totals into a spreadsheet for distribution.
In Labview I create a new report and use the distribution sheet as my template, but how do I complete
the steps of loading the raw 5 minute data into labview and then paste it into the hourly total spreadsheet and then transfer those totals into the distribution template?
I have been trying to figure this out for over a week, and I am getting nowhere.
Any response would be appreciated.
Thanks
Jason P
Jason Phillips

Lookout saves the files in .csv form which can be opened in Excel. I did make some progress by using the "append table to report" vi which allowed me to put values into an array and then those values were entered into my template on my report vi.
Where I am stuck now is I want to be able to put values into my template from a .csv file, not from an array I have to manually put numbers in.
Once those values are in my template I want to pull summed values from the template and place them into a final excel file for printing.
I have attached examples of the files I am working with to help you better understand what I am trying to do.
I hope that makes sense.
Jason Phillips
Attachments:
HourlyTotalsTemplate.xls ‏120 KB
eb_rain_gauge_ss.csv ‏23 KB
EastBankHourlyRainReport.xls ‏28 KB

National Instruments releases LabVIEW Report Generation Toolkit for Microsoft Office.

The new LabVIEW Report Generation Toolkit for Microsoft Office is a library of flexible, easy-to-use tools for programmatically creating and editing Microsoft Word and Excel reports from LabVIEW. Whether you need to generate reports summarizing manufacturing test results or compile process statistics to improve your production yields, this toolkit speeds your development of customized, professional reports.
To see examples of this toolkit or get more information please visit :
http://www.ni.com/labview/report_gen_toolkit.htm

It is a bit limiting though. I built my own set of VI's, a toolkit if you will, that does some of what this tookit does. But, I also wrote some functionality that isn't available in NI's kit, such as creating charts as separate worksheets and linking the charts to data on another worksheet. All in all, the toolkit is great, but you can't get as much out of it as you can using the ActiveX calls yourself.

LabVIEW 6.1 If For Loop count terminal is zero then value going through the loop is not passed on to the output of the loop

Hello, one of our customers just encountered an execution error in a vi running under LabVIEW 6.1, which doesn't exist under LabVIEW 5.1 or 6.01. I have a simple vi that has two encapsulated For Loops. Two string arrays go in, one goes out of the outer loop. Inside the outer loop the first array is indexed. The string which results from this indexing is compared with all other strings from the second string array in the inner loop. If it matches one of the strings of the second array, it is not outputted, otherwise this string goes through the inner For Loop to the output of the inner loop and from there to the output of the outer loop. The count
terminal of the outer/inner loop is connected to the Array Size of the first/second string array. If the second array is empty, that means that the element in test from the first arry cannot match anything from the second array, so the element in test is send to the output of the inner loop and from there to the output of the outer loop. This works fine in LabVIEW 5.1 and 6.01, but NOT in LabVIEW 6.1. In LabVIEW 6.1 the inner loop is never executed if the count value is zero (which is correct), but the data line running through the loop is not executed either, which is different to what LabVIEW 5.1 and 6.01 do. There, the input string is sent to the output of the inner loop correctly even if the loop counter is zero. The solution is easy - I just have to connect the output of the outer loop to the data line BEFORE it enters the inner loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is supposed to be a feature, but it brings some incompatibility in programming between the
different LabVIEW versions.
Best regards,
Gabsi

Hi,
When a for-loop runs zero times, all outputs are 'undefined' (and should
be).
Besides, how would LV know what the output of a not executed routine should
be?
It might be handled differently in LV5 and LV6, which is unfortunate. In
both cases, the result is undefined.
It's not a bug. It's just something that should be avoided in any LV
version.
> The solution is easy - I just have to connect the
> output of the outer loop to the data line BEFORE it enters the inner
> loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is
In some cases this does the trick. But if the data is changed in the inner
loop, this will effect the results if the N is not zero.
Technically, I think the output in this construction is also 'undefined'.
But LV handles this as expected / desired.
Another solution is to use a shift register. If N is zero, the input is
directly passed through to the output.
Regards,
Wiebe.
"Gabs" wrote in message
news:[email protected]...
> LabVIEW 6.1 If For Loop count terminal is zero then value going
> through the loop is not passed on to the output of the loop
>
> Hello, one of our customers just encountered an execution error in a
> vi running under LabVIEW 6.1, which doesn't exist under LabVIEW 5.1 or
> 6.01. I have a simple vi that has two encapsulated For Loops. Two
> string arrays go in, one goes out of the outer loop. Inside the outer
> loop the first array is indexed. The string which results from this
> indexing is compared with all other strings from the second string
> array in the inner loop. If it matches one of the strings of the
> second array, it is not outputted, otherwise this string goes through
> the inner For Loop to the output of the inner loop and from there to
> the output of the outer loop. The count terminal of the outer/inner
> loop is connected to the Array Size of the first/second string array.
> If the second array is empty, that means that the element in test from
> the first arry cannot match anything from the second array, so the
> element in test is send to the output of the inner loop and from there
> to the output of the outer loop. This works fine in LabVIEW 5.1 and
> 6.01, but NOT in LabVIEW 6.1. In LabVIEW 6.1 the inner loop is never
> executed if the count value is zero (which is correct), but the data
> line running through the loop is not executed either, which is
> different to what LabVIEW 5.1 and 6.01 do. There, the input string is
> sent to the output of the inner loop correctly even if the loop
> counter is zero. The solution is easy - I just have to connect the
> output of the outer loop to the data line BEFORE it enters the inner
> loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is
> supposed to be a feature, but it brings some incompatibility in
> programming between the different LabVIEW versions.
> Best regards,
> Gabsi

How to download LabVIEW 11 Student Edition for OS X

I received my activation number for LabVIEW 11 Student Edition by email for participating in an online lecture and solving a problem.
In the email there was no link to download the software.
Where can I find a download link for LabVIEW 11 Student Edition for OS X?

Hi,
I will try to go through it with you and I believe we will find a solution.
The 2011 version of LabVIEW for OS X is no longer available from this link, a new version was released in the meantime. First I'd like to try to get a new version to you. Can you please check whether you can't get the serial number for the new version as well? Usually these student versions are available for free.
In the worst case I will upload you the old installer on the FTP.
Jakub Prokeš
NIEE Aplications Engineer

Labview 6 compatible driver for HP89410A Vector Analyzer

Does anyone know where I can get a labview 6 compatible driver for an HP89410A Vectory Analyzer?
I have found labview 7 and labview 8 drivers for the hp894xx family of devices, however I cannot use them as I only have labview 6.
Barring a prewritten driver, how hard would it be to convert a labview 7 driver to make it compatible with labview 6?

The conversion is easy since there is a VI Tree VI in the driver. Since the driver was originally written in 1999 and has been up-converted to 7.0 and 8.0, saving it back down to 6.0 shouldn't be an issue.
Attachments:
hp89400_6.zip ‏1194 KB

Is Ardence RTX required when I use PCI-7831R with labview real-time module for RTX target

I am new in the labview real-time field. I want to use labview real-time module for RTX target on only one desktop. My card is PCI-78331R. Is Ardence RTX necessary? Why I cannot find my card in the MAX after I configured the RTX?
Thank you very much.

Hi Ziaozhongda,
You must have the RTX runtime engine installed before the LabVIEW Real-Time RTX module will install. Additionally, you should follow the instructions in the "Using the NI PCI-7831R with the LabVIEW Real-Time Module for RTX" section of Getting Started with the NI 7831R (page 8).
Please see Configuring Hardware for Use with RTX.
Also useful is "How Can I Validate That My PC Will Run RTX?

LabView database connectivity toolkit 1.0.1 compatibility with MS-ACCESS 2010 / Labview report generation toolkit for Office 1.1.3 compatibility with Office 2010

In the very near future we will be forced to upgrade to Office 2010 Company wide and I am a little concerned with some of our older test platforms that have applications built in LabView 8.2.1. These applications save data to MS-ACCESS 2000 databases using the LabView database connectivity toolkit 1.0.1. Office 2003 is also loaded on these test platforms with all test reports generated using the LabView report generation toolkit for Office 1.1.3.
I have not gotten my hands on a copy of Office 2010 yet to see if there will be any compatibility issues. Does anyone have any experience in this area?

The MS-Access part is fairly well isolated through the ADO interface LabVIEW uses. The only possible problems there IMHO are difficulties with possible Acess compatibilities itself such as an example, SQL statement you may have invoked directly through the ADO interface. Maybe you did use a depreciated command back then that has since been removed. As long as the only thing you do are simple INSERT and SELECT statements only, I would expect it to just keep working.
The Report Generation interface is a different beast. Microsoft manages to change the Automation interface with every version of office in a way that strongly binding applications like LabVIEW break on. There is no good way around that except not changing those methods, but that is a cause that has been lost already. You will certainly have to verify the version dependant Report Generation API VIs to still work with Office 2010 and most likely you will have to make some changes to those VIs to make them work again with the modified ActiveX interface of Office 2010. Note, that I have no experience with porting report generation to Office 2010 but I have had some headaches from porting that between Office 97, 2000, 2003, and 2007.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

LabVIEW RT driver support for CEI-620?

Hi All,
I am using PXI-8106 to run heavy-duty communication and one chasis holds the CEI-620 card (third party ARINC429 card from GE, formerly Condor Engineering). Currently on the PXI controller only runs LabVIEW RT (Pharlap) since I did not want to install Windows OS to slow the performance. Now here it is the problem, GE does not provide LabVIEW RT driver support for CEI-620 (they do have LabVIEW RT support for CEI-830 though, but that card is PMC interface). Basically right now MAX can not recognize the CEI-620 card on the host side, and I can not deploy my ARINC429 application VI to the target PXI controller. I am wondering anybody here has encountered the same problem and develop the LabVIEW RT driver for CEI-620 on his own?
Thanks.
Martin Ding
Senior Project Engineer
S-TEC Corporation

Hi,
Unfortunately I don't have much more information to offer. I would suggest checking to make sure you have all the correct device information whe you create the ini file. I think you should still be able to develop a driver for a poll based device. It should be easier to generate an ini file if you do not require interrupt information. Make sure you have the correct identification information and try using the VISA Driver Development Wizard again.
Eric A.
National Instruments
Distributed I/O Product Support Engineer

Need to know the highest version of labview that was released for HPUX

Does anyone know the highest version of labview that
was released for HPUX operating system ?

Hello!
The latest version of LabVIEW for HP-UX is LabVIEW version 6.0.2.
Thanks for contacting us!
Regards,
Colin C.
Applications Engineering
Colin Christofferson
Community Web Marketing
Blog

LabVIEW Report Generation Toolkit for Microsoft Office 1.1.2

Where is possible to buy LabVIEW Report Generation Toolkit for Microsoft Office v1.1.2?
Thanks.
Francisco

You are right, the page does not say that but the local distributor says that I have to purchase an update to the latest version of LabView: about USD 1000. I can't believe that.

Upgrading LabView 2011 to 2012 for Mac OSX

I am considering Upgrading LabView 2011 to 2012 for Mac OSX.
Is this a free upgrade?
Is a Mac OSX version available?
Is the NXT module still working in LabView 2012?
LabView 2011 ain't broke but I just recived a vi which requires a newer version :-(
Thanks.
Michael
Dr. Michael Vallance
Future University, Japan.
Homepage http://www.mvallance.net
International Virtual Environments Research Group (iVERG) http://www.iverg.com

Is this a free upgrade?
It depends if you have a current service contract. You get a 1 year period where you will get updates to LabVIEW after purchase.
Is a Mac OSX version available?
http://www.ni.com/labview/os-support/
Is the NXT module still working in LabView 2012?
I have no idea.
LabView 2011 ain't broke but I just recived a vi which requires a newer version :-(
You can download a 30 day trial from the NI site.
http://www.ni.com/labview/whatsnew/upgrade/
You might have to contact NI directly since you are not in the US.

"labview dsp test integration for TI dsp": not available

hi
i have been trying to locate this particular toolkit "labview dsp test integration for TI dsp",but it gives me error "no content available. i have been refering to this particular book that guides on how to use labview with TI dsp.
check chapter 9,section 2(ie 9.2).
http://books.google.co.in/books?id=f-rFsAwd3TAC&q=TMS320C6173#v=onepage&q=TMS320C6173&f=false
http://digital.ni.com/public.nsf/allkb/305E2B0DA391CD4786256D0C006EE31C
but i was goin through i found that this toolkit is maybe not anymore supported by NI.can some one plz let me know on how to interface my TI dsp like TMSC6713b etc nd burn progm on it using labview.

Debarati,
I did some more research into your issue and found out that unfortunately, NI no longer officially supports the DSP Test Integration Toolkit as seen here: http://zone.ni.com/devzone/cda/tut/p/id/5839
I also see that you located our example VI here http://zone.ni.com/devzone/cda/epd/p/id/4311 and that the VI asked you for a .pjt file that you could not locate in CCSv4. Being that we no longer support the DSP Test Integration Toolkit, your next course of action would be to contact TI and inquire what .pjt file corresponds to in the newest version of CCS. I hope TI can be of more help to you with this issue since, as I said before, we no longer support this toolkit.
My apologies,
Larry H
Applications Engineer
National Instruments

LabVIEW openings at Noida for Sankalp Semiconductor

Similar Messages

Maybe you are looking for