LabVIEW Run Time Engine and ActiveX Automation Server

Hi,
I have a question related to LabVIEW Run Time Engine and ActiveX Automation Server:
We have a tool developed in LabVIEW and TestStand. End user interface is a LabVIEW GUI (it's an executable) which executes TestStand sequences. Some TestStand sequences call lower level LabVIEW VIs.
Everything works fine with LabVIEW installed, but I was wondering if I could run this tool on deployment machine with only LabVIEW run time engine installed. We are using LabVIEW 6.1 and with only the run time engine installed, I get the error message: "Unable to launch the 'LabVIEW.Application' ActiveX automation server ".
BTW, we are planning to upgrade the versions soon.
Is it possible to make things work only with the run time engine?
Thank you.

Thanks for the response, Brian.
I did upgrade to LabVIEW 8.0 and TestStand 3.5. Everything works fine on the development computer where LabVIEW and TestStand is installed. On the target computer in the lab, I installed LV RTE 8.0 and TestStand 3.5, and now when a VI is called in a sequence file, I get the following:
RunState.PreviousStep.Result.Error.Code -18002
RunState.PreviousStep.Result.Error.Msg "LabVIEW: The VI is not executable"
So, the executable opens and works fine (which means that the LV RTE is installed properly), but when a sequence calls a low level VI, it does not make it through.
comments/suggestions are appreciated. Thanks.

Similar Messages

Uninstalling LabVIEW Run-Time Engine 6.1

Hi, I get an error message during uninstalling NI LabVIEW
Run-Time Engine 6.1:
Error 2727 NETSCAPEPLAGINSDIR
How can I fix this problem?

Armen,
Here is my guess as to what happened:
1. You had Netscape installed on your machine.
2. You installed the LabVIEW Run-time Engine which installed the remote panel plugin into Netscape.
3. You uninstalled Netscape.
4. You are trying to uninstall the LabVIEW Run-time Engine.
If this is correct, then try installing Netscape again, uninstall the LabVIEW Run-time Engine, and finally uninstall Netscape again. If this does not work, then please submit a phone request at http://www.ni.com/ask to get help with MSIBlast.
Randy Hoskin
Applications Engineer
National Instruments
http://www.ni.com/ask

What is "LabVIEW Run Time Engine"?

I'm trying to find the differences between two computers that I'm troubleshooting. One of them is my development system which has the whole Development Suite installed, and the other is a test station which has LabVIEW 8.0 Evaluation Version installed. When I was looking through the list of programs in my development system (in Add/Remove Programs), I found a program named "LabVIEW Run Time Engine" and the size is 0.11 MB that is not in my test station. I thought all the NI components are installed under "National Instruments Software" including the Run Time Engine...
Does anyone knows what this is?
See-Ming

The Run Time Engine is a library of routines that a compiled Labview program needs to run on a system that doesn't have the development environment. It is similar to Visual Basic's vbrun.dll, which compiled VB programs need to run.
As far as I know, the run time engine gets installed whenever you install any Labview development environment. This engine is usually only necessary when running a Labview program compiled to an exe format. Both the exe and the run time engine can be installed on another computer so that the program can run without having to buy another development package for that computer.
The runtime engine is called LVRT.DLL. Search for it. For version 7.1, the run time engine is in C:\Program Files\National Instruments\shared\LabVIEW Run-Time\7.1\lvrt.dll
- tbob
Inventor of the WORM Global

Can't install LabVIEW Run-Time Engine 6.1 on Windows Terminal Server

With my system admin, we tried to install the LabVIEW Run-Time Engine 6.1 on our Windows Terminal Server NT4. And we get an error all the time:
-install using the plugin
-install using LVRTE.exe
-install after rebooting the server
But I remember that we could install the Run-Time Engine 6.0 on another Windows Terminal Server NT4.
Is there any compatibility issues with the new Run-Time Engine 6.1 ??
Thanks for your help
Cyrille

Cyrille,
What is the error that you get when trying to install the run-time engine?
Are you installing it from the LabVIEW CD, or did you download it from the web site?
To further troubleshoot this problem, it would be best if you send us an email to [email protected] and send the above information.
Also, try running the installer from the command prompt window, and use the following syntax:
setup.exe/l*v
This will save the error log to the file you specify. Send us also this file to help us troubleshoot.
Thanks
Zvezdana S.
National Instruments

Error involving Report Generation Toolkit and Labview Run Time Engine

Developed an application using LabVIEW 6.1 and LabVIEW Report Generation Toolkit for Microsoft Office 1.0.1. From there, tried to build a shared application for use with the LabVIEW Run Time Engine. The Run Time version functions properly until "New Report.vi" is called and then an error is generated, code 7, calling out "Open VI Reference in New Report.vi" could not be found. When building the application, I did include the "NI Reports Support" in the advanced installer options. The machine used for original development and application build is running Windows XP Pro and Office XP. Any suggestions??

I am having the exact same problem but with LV 6.1 and M/S WORD 2000. It appears that the "New Report.vi" is trying to open "C:\APP.DIR\Word_Open.vi" and "C:\APP.Dir\Word_Open_Document.vi" by reference. The "OFFICE 2000.TXT" says that "_exclsub.llb and _wordsub.llb must be added as support files when building an application or a dynamic link library with the application builder." I added them as Support Files and I copied them to the "C:\TESTER\" where the TESTER.EXE is and I still get ERROR 7 in "NEW REPORT.VI" at VI OPEN REFERENCE.
Do I need to make a "C:\TESTER\DATA\" sub-dir and put the support files there?
I am building on MY COMPUTER on F: Drive on a network and transporting files to the real Tester.
I displayed my App.Property of APP.DI
R at start up and it is C:\TESTER\ ! How would my application know that "Word_Open.vi" and "Word_Open_Document.vi" are actually inside the _wordsub.llb?
Any ideas ?
Greg Klocek

NI 5660 Driver DLL Errors when using Teststand 2010 and LabVIEW Run-Time Engine 2010

This problem seems similar to the post "Resource not found error in executable on development machine." but I didn't want to repost under that thread because I only happened upon it by chance and none of my searches brought me there... so I made a more descriptive Subject.
I am working on a system that uses a PXI Chassis with a NI 5600 Downconverter and a NI 5620 high speed digitizer, among other PXI Cards.
I inherited working code written in LabVIEW 2010, running with the LabVIEW Run-Time Engine 2010. The code was using a custom executive and my task was to rewrite the test using TestStand 2010. I reused the majority of the old code. The old code used NI-5660 to control the 5600 and 5620. When I run my sequence using the LV Development System and TestStand, it runs without any issues. When I change the adapter over to LabVIEW Run-Time Engine 2010, all of my NI5660 VIs become broken due to DLL issues. It warns that the nipxi5600u.dll was not initialized correctly. Many of the errors are associated with the NI Tuner and NI Scope. After this LabVIEW will crash randomly, and the seqeunce will not work in TestStand even when back with the LV Development Adapter. The only way to recover after this is to restart the computer - TestStand automatically reverts back to the development system, the VIs are no longer broken and the sequence works again.
I have all of my VIs associated with a project. After reading a little bit about DLLs and TestStand, I found all of the DLLs in the dependencies section of my project and added them to my TestStand workspace. I also used Dependency Walker to track down the problems with the nipxi5600u.dll, the 2 DLL files that it said were not found already existed in the same folder as the original DLL (C:\Windows\System32). I have also performed a Mass Compile to make sure everything was running in LV 2010. If I skip the steps involving the 5660, my entire sequence runs fine.
The previous code was running with the LabVIEW Run-Time Engine without any issues. Is there just a step I am missing? Has anyone seen anything like this before? I can send screenshots of errors to provide more detail if necessary.

I have tried some more things and still can't get it to work. I have added the VIs mentioned in the Notes On Creating Modulation Executables KB both to the TestStand workspace and the LabVIEW project holding all of my VIs. This did not change the results.
When I try to run my sequence, The first error I get is shown in Error 1445.bmp. This happens when I try to use the NI 5660 initialize.vi. If I click ignore, the next error I see is shown in Error -20551.bmp. When I try to open the VI to look at it, I get the 2 DLL errors shown in Error loading nipxi5600u.bmp and Error loading nidaq32.bmp. When I close TestStand, I get the error LabVIEW Fatal Error.bmp.
Attachments:
Error1445.JPG ‏164 KB
Error -20551.JPG ‏174 KB
Error loading nipxi5600u.JPG ‏9 KB

Teststand error states that a vi failed to load in the Labview Run-Time Engine

I am getting an error in teststand that states that a vi failed to load in the Labview Run-Time Engine version '14.0.1'
If I look at the software loaded on my system with the NI Measurement and Automation Explorer I have Labview Run Time engines for version 2009, 2010, 2011, 2012, 2013, & 2014 on my system.
How do I get this VI to run on this system when it is called by test Stand?
Thank you

The RTE 14.0 was loaded as part of my deployment and after I ran this I got an update notice for the F1 patch which I also loaded.
I do not have labview loaded on this system, only the run time engines from running my deployment.
When I launch t he teststand sequence, when it calls the labview VI, I get the following error moessage:
Error: Failed to load VI 'C:\builds\RelayVoltageMeaure.vi' in the LabVIEW Run-Time Engine version '14.0.1'. LabVIEW: The VI is not executable. This error may occur because the VI is either broken or contains a subVI that LabVIEW cannot locate. Select File>>Open to open the VI and verify that you can run it. VI Path: C:\builds\RelayVoltageMeaure.vi[Error Code: -17600, Failed to load a required step's associated module. ]
I have attached the teststand sequence if this helps.
Thanks
Attachments:
QuantumDigitalBd.seq ‏13 KB

Unable to locate labview run time engine (lab view 8.5)

Hello I have a problem whit the labview 8.5 installer. I have created I project with included a .vi file (a simple panel wich control a serial port, with parameters (baud rate, stop bits, ...)), then I have created an application for this file (.exe) and then the installer (I have included the labview run time engine 8.5). When I run the setup.exe I have the following error message:
Unable to locate labview run time engine, the application require a labview run time engine 8.5 or compatible...
What I'm missing??
Thanks
Maurizio

are there one other reasons why it would not work. I have asimilar problem.
I intsalled version 8 of run time engine and acrtivated software. Now I am trying to run compiled application provided to me by third party.
When I click on application it says
Unable to locate LV run time engine
Test server requires a version 6.0 or compatible LV engine.
How do I know if the engine I installed and activated is running and is it supposed to be able to execute a program which is expectin rev 6 of the rund engine?

Include LabVIEW Run-Time Engine in C# Project Distribution

I have written a software package in Visual Studio using C# which calls a number of functions from a dll which I have built in LabVIEW. I am now trying to produce an installation program for my C# package but can't quite work out how to include the LabVIEW Run-Time Engine in this installation.
I am creating the installation program by defining a Visual Studio Deployment Project and I have added my LabVIEW dll to this. However, the dll requires the LabVIEW Run-Time Engine to also be installed on the target PC. I was hoping that there would be a set of files to implement the installation of the LabVIEW Run-Time Engine that I could include in my Visual Studio Deployment Project and do the installation of both my C# code and my LabVIEW dll (inc Engine) in one operation. Is this possible? Or do I need to produce a LabVIEW installation for my dll separately from the C# installation?
Info:
Development OS = Windows 2000
Target OS = Windows XP
C# Development Environment = Microsoft Visual Studio 2005 V8.0
LabVIEW Version = 8.5
Also, I am using the Order Analysis Toolkit and noticed that there seemed to be an 'Order Analysis Run-Time Engine' installed on my PC. Do I need this too?
Thanks for any help.
CAS

Hi CAS,
One way of automating the installation of the LabVIEW run-time engine is to use commands in a batch file (*.bat). These commands would be executed automatically at the same time as your distribution installer to install LVRT with your C# application. For more information on command line options, have a look at this KB. I don't have so much knowledge of C# distributions, though, so there may be a better way to approach this that someone else in the community could advise you on.
With regard to the order analysis toolkit, you will also need this runtime engine installed. A point to note, though, is that the toolkit requires a run-time licence to be deployed in this fashion. It is now part of the Sound and Vibration Measurement Suite and needs to be licenced accordingly.
I hope this helps!
Best regards,
Tom
Applications Engineering, NI UK

NI LabVIEW Run-Time Engine + TCP/IP

Hello, Anybody knows how to activate TCP/IP service on PC with standard NI LabView Run-Time Engine installed. If I trying communicate with server from my PC (LVRTE) its works correctly. However, when I am trying interchange client and server applications it appears with error 1. Probably I need to add some settings to *.ini files on PC with LVRTE? --- Alex

<Alex> wrote:
Client/Server applications are communicate via standard TCP/IP VIs. I have tried to add 3 line as you wrote to server.ini, but it's didn't help
As I indicated, the lines are only applicable to using the VI Server. You had not indicated whether you were using the VI Server or just the TCP/IP VIs. At this point we need a better explanation of what you're doing. Specifically:
What does this: "If I trying communicate with server from my PC (LVRTE) its works correctly." mean? What is the "server"? What's it running? What do you mean by your "PC (LVRTE)"?
What does this: "However, when I am trying interchange client and server applications it appears with error 1" mean? What is the "interchange client" and the "server applications". Reading this implies you have more than one application running on the "server", whatever that is.
Seeing some code wouldn't hurt either.

LabVIEW 2011SP1 Error building installer: LabVIEW Run-Time Engine 2013 is missing 3 dependencies???

I'm having a problem building an installer in LabVIEW 2011SP1.
It's been a while since I've tried to build an installer but it used to work fine and building executables is still working fine.
Now when I try to build the installer I get "The build was unsuccessful."
Possible reasons: Error generating preview for My Application 3.1.7.
Details:
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
CDK_Build_Invoke.vi.ProxyCaller >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> IB_MSI.lvclass:Build.vi >> IB_MSI.lvclass:Engine_InitializeDistribution.vi >> IB_MSI.lvclass:Report_Preview_Error.vi >> IB_Source_Container.lvclass:Report_Preview_Error.vi
Loading product deployment information
*** WARNING ***
NI LabVIEW Run-Time Engine 2013 is missing 3 dependencies. This product, or other products that depend upon NI LabVIEW Run-Time Engine 2013, may not function properly while the dependencies are missing. Visit ni.com/info and enter the Info Code "" for more information.
*** Error: An internal error occurred for which the cause is unknown. (Error code -41)
*** Error Details:
Error in MDF API function: _MDFCommon_GetNextLogMessage
Error in MDF::GetInstance - MDF static instance is not initialized!
*** End Error Report
Loading product deployment information
*** WARNING ***
NI LabVIEW Run-Time Engine 2013 is missing 3 dependencies. This product, or other products that depend upon NI LabVIEW Run-Time Engine 2013, may not function properly while the dependencies are missing. Visit ni.com/info and enter the Info Code "" for more information.
The really strange thing about this is that I'm using LabVIEW 2011SP1, I don't even have LabVIEW 2013 installed, not even the runtime.
Where is the problem? Why is it even complaining about LabVIEW 2013? Has anyone seen this before?
Troy
CLDEach snowflake in an avalanche pleads not guilty. - Stanislaw J. Lec
I haven't failed, I've found 10,000 ways that don't work - Thomas Edison
Beware of the man who won't be bothered with details. - William Feather
The greatest of faults is to be conscious of none. - Thomas Carlyle
Solved!
Go to Solution.

I do have the LabVIEW 2013 discs but didn't install it.
I checked in Control Panel > Programs and Features > National Instruments Software and the LabVIEW 2013 Run-Time is not listed there.
I also checked in MAX > Software and I must have missed it the first time I looked. LabVIEW Run-Time 2013 is listed there after all.
Now I remember installing VISA 5.4 to get rid of a nasty bug. It must have installed the 2013 Run-Time when I did that.
So now I need to distribute 2 runtimes with my application?!?!
Troy
CLDEach snowflake in an avalanche pleads not guilty. - Stanislaw J. Lec
I haven't failed, I've found 10,000 ways that don't work - Thomas Edison
Beware of the man who won't be bothered with details. - William Feather
The greatest of faults is to be conscious of none. - Thomas Carlyle

Executable not working - Looking for LabVIEW Run-Time Engine

This has been one of those days.
I'm trying to create my .exe file to place onto another computer. I've done this before with success. But that was then and this is now.
I believe I have all the files I need in my LLB, and I believe I did my application distribution correctly and I believe I built the DLL correctly. But when I took the resulting .exe file and placed it on another computer and attempted to run it, it gave me the error message: "Unable to locate LabVIEW Run-Time Engine. Program requires a version 7.1 (or compatible) LabVIEW Run-Time engine. You should have already realized this, you moron."
Anyone have any idea where I went wrong or what step I might have missed? This has been a crazy, non-stop, massive brain fart of a day and I can't seem to remember what I'm missing here.
Amateur programmer for over 10 years!

Hi.
Whenever you want to use executables or .dll's created with LabVIEW you must make sure that the LabVIEW runtime engine of the SAME version as the LabVIEW version used to create the files, is installed in the target computer.
There are basically 2 ways to get the run-time engine installed on a computer:
1. (the one I prefer): Download the correct version of the LabVIEW run-time engine installer from www.ni.com/downloads, or more specifically from
http://digital.ni.com/softlib.nsf/websearch/369618104E25B08E86256F54006A4E2F?opendocument&node=132050_US
for the latest one. Once you have the installer for the run-time engine, just install it in the target computer. I prefer this option because the run-time engine is installed independently, so if you then uninstall your program, the run-time engine remains.
2. Create an installer for your program that includes the run-time engine. To include the run-time engine, when you are creating your application, go to the "installer settings" tab, click on "Advanced" and make sure there is a checkmark on "include LabVIEW run-time engine". This way when you install your program in the target computer, the run-time engine will also be installed.
Just as a note, any computer with LabVIEW on it, will also have the run-time engine.
Good luck.
Alejandro

UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71

UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71 REQUIRES A VERSION 7.1 (OR COMPATIBLE) LABVIEW RUN-TIME ENGINE。PLEASE CONTACT THE VENDOR OF LVBROKERAUX71 TO CORRECT THIS PROBLEM
Uninstalled DAQ and reinstalled. MAX still throws an error.
Any Isead besides uninstalling 3/4 of my software?
Merry Christmas!
Matthew Fitzsimons
Certified LabVIEW Architect
LabVIEW 6.1 ... 2013, LVOOP, GOOP, TestStand, DAQ, and Vison

To clean up your system, you will need to uninstall the LabVIEW 7.1 run-time engine, and the "LVBroker," and the "LVBrokerAux71" components using the MSI Blast utility. To obtain this utility, please create a service request for phone or e-mail support, and contact one of our Applications Engineers about this issue. Thank you!

Unable to locate the LabVIEW Run-Time engine

Using LabVIEW 2011, I have built an executable and installer including the LabVIEW Run-Time engine. I built the app on a 32-bit system. I'm deploying it to a Windows7 64-bit system. When I ran the installer, rebooted, then tried to run the app, I got an error messsage stating "Unable to locate LabVIEW Run-Time Engine", stating that the LVRTE 2011 was needed to run the app, and asking if I want to download from NI. I have tried downloading the RTE and re-installing it, but when I try, I get an error message from the installer stating that there is a newer version of the RTE already installed, and the installer exits! I have tried un-installing the application, but have had no luck removing the RTE. Now I'm stuck. The re-installed executable application says it can't find the RTE, and the RTE installer says there's a later version already installed!
I can't go forward or backwards!
Prior to running the installer for this app, I had a working LVRTE for 2011, and was running some other executable LabVIEW programs on the target box. However, since this new application had additional components not included in the original install of the RTE, I built the new installer which included the additional components. Once I ran that installer, my problems began.
In my frustration, I've tried downloading from NI both the 32 and 64-bit versions of the RTE, and installing them. I realize that the app was built on a 32-bit system, so the 32-bit RTE SHOULD have run it fine, but didn't.
At this point I have removed the 64-bit RTE using the NIUninstaller. I believe I need to completely remove all 32-bit RTE components and start over, but I have not been able to. The 32-bit RTE does not show up in any un-install utilities I've found.
What could be causing this problem, and how do I get past it??
Thank you.

One thing I did discover in my struggles is that the RunTime engine on the target box needs to be based on the environment of the development box. So if you built the app on a 32-bit machine, you would need to install the 32-bit RTE, even on your 64-bit target box.
The RTE Uninstaller might not show up in the Windows Add/Remove Programs utility. In my case the 64-bit RTE uninstaller showed up, but the 32-bit did not. The NiUninstaller (C:\Program Files\National Instruments\Shared\NIUninstaller) did list both RTEs for uninstalling, but still didn't get me past the problem.
I was finally only able to get past the problem by doing a system restore to a point in time prior to my changing of the RTE.
Good luck.
Dan

NI-LabVIEW run-time engine interop 2010 failed to install

Hi,
While installing Labview 2010 (32 bit) I got an error message:
NI-LabVIEW run-time engine interop 2010 installation has failed with the following error:
Error 1935. .... (see the .ppt for screenshot if interested)... HRESULT 0x8002802F
I googled HRESULT 0x8002802F and found a page that said that this error is usually b/c of a missing/corrupt entry in the registry: file %windir%\system32\mscoree.dll, and that "repairing the highest version of the .NET Framework on the system will correct any problems resulting from this error."
I have verified that mscoree.dll is not present, and I don't have the .NET Framework installed on my system. SO, I have the following questions:
1) do you concur with the advice given on the page referenced re: the reason for the error;
2) If so, should I install .NET Framework, and what do I then need to do in LabVIEW to tell it that the .dll is now present?
3) If your opinion is other, what do you advise?
Cheers
Attachments:
Labview Installation error.ppt ‏227 KB

Hi Luke,
After doing some research, there are two possible solutions.
1) According to a KB, it could be your antivirus. You may want to try to turn off any spyware blocking software such as Ad-Aware, Norton, etc and try the installation again.
2) Another customer had the same error, and they got it working by installing .NET 3.5 from Microsoft's website and then installing LabVIEW again.
Hope one of those options work for you!

LabVIEW Run Time Engine and ActiveX Automation Server

Similar Messages

Maybe you are looking for