LAN goes down in the moment I change the gateway to Core, but it is not the gateway for users.
Hi,
I have my DHCP configured in order to deliver the next default gateway, the 52.44.72.254.and all others devices have the same default gateway, the 52.44.72.254.
The Core switch with IP 52.44.72.200 has next route: ip route 0.0.0.0 0.0.0.0 52.44.72.254
The issues comes when I change it to Core switch, everything goes down.
I am adding a new network, we will replace the 52. In the moment we enable the Core in the 10 network with a new default gateway, everything goes down.
Everything should work as today because the VLAN 1, where the 52 is working, keeps as today. We change only the IP for Core sw.
When the network is down, I tracerted the external routes, and all traffic stops in the Core sw.
It looks like If it was routing, but it is not.
Do you have any idea what could happend?
FYI:
interface Vlan1
description VLAN DATOS
ip address 52.44.66.254 255.255.255.128 secondary
ip address 52.44.72.200 255.255.255.0
no ip redirects
ip local-proxy-arp
ip route-cache same-interface
interface Vlan95
ip address 10.106.128.2 255.255.255.0
interface Vlan300
ip address 10.106.130.1 255.255.254.0
interface Vlan301
ip address 10.106.134.1 255.255.255.0
Thanks by your help, best regards. Luis.
I dont understand your configuration. What is your next hop device thats defined in your default route? A router? Are you trunking to the router? Is IP routing enabled? More of the configuration of this core and next hop device will be helpful.
Similar Messages
-
Trying to get the ipad to open after doing a software update. I only get the itunes logo with an arrow pointing toward it and a lock symbol with a line going down towards the screen button. Any suggestions to get this to open?
You are in Recovery Mode. Follow the instructions below to recover your iPad.
http://support.apple.com/kb/ht4097 -
Screen goes black, shut the lid for a few minutes, open the lid the turn on chime comes on and the screen comes back to life. The computer itself has continued to update just no screen. After a few minutes goes black again. Is logic board going bad or graphic card issue? Trying to decide if computer is worth repairing as it was made in 2007.
It does sound like you might have a faulty video connection. See if you can make a Genius Bar appointment at your local Apple Store.
-
I down loaded the update for 4 and when I get to the end where is you click finish, it tells me to close firefox, but I do not have it open. Now I can not get in to Firefox at all. PLEASE Help.
You can get Firefox 3.6 from http://www.mozilla.com/en-US/firefox/all-older.html
You should still have your profile folder, so when you install 3. you will get your bookmarks and other user data back.
There is a third party version of Firefox that runs on OS X 10.4/10.5 and PPC Macs, for details see http://www.floodgap.com/software/tenfourfox -
HT1351 where can I down load the software for my Ipod, 4gb model with click wheel
where can I down load the software for my Ipod, 4gb model with click wheel
The current version of iTunes contains or will download all of the necessary software for it.
(81536) -
When I click on download button, it goes right to the "thanks for downloading" splash page,and yet nothing has downloaded -- no download file box comes up, nothing.
I stupidly uninstalled the version of iTunes I had working on my notebook when the update kept failing and am now unable to get anything happening at all.I had probs with 7.2. Reloaded 7.1 works fine. I think 7.2 needs some more work before it will work for me.
-
Steps to find the password for users as sysdba
What are the steps to find the password for users in dba_users as sysdba?
It is in encrypted form ? How can I view it ?
Pls tell in steps ?I asked for sysdba
When he can change password why can't he view ?Can you see the users password on a windows domain? No
Can you see the users password on a Unix box? No
Can you see the users password on a mail server? No
Why would it be different in Oracle?
Why is hacking coming here ?Because it's something against the way the software works.
This can, and is, dangerous to let the administrator (Oracle, MsSQL, Win*, Unix,...) know the users password for so many reasons. For example:
. Privacy
. Etiquette
. Password reuse (password reused for Bank account, etc)
. [insert a whole bunch of other good reasons I'm not going to bother writing]
And anyway it is useless!
Yoann. -
Changed my Apple ID email, but ICloud does not recognize my new login, only my old one (which is now non-existent) and requires the password to do anything. Everytime I go onto the ICloud page it shows my old email and requires the password, but I can't exactly type in a password because that won't work. I can't find a way to change my email or delete ICloud.
If the old ID is an earlier version of your current ID, do the following:
Make sure you are signed into iMessage and FaceTime with your current ID. If they are signed into the old ID, go to Settings>Messages>Send & Receive and Settings>FaceTime, tap the ID, sign out, then sign back in with your current ID.
Then temporarily recreate the old ID by going to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. (You should not have to verify the old email account so it doesn’t matter if you no longer have access to it.) Now go to Settings>iCloud, turn off Find My iDevice and enter your current password when prompted (even though it prompts you for the password for your old ID). Then go to Settings>iCloud, tap Sign Out (or Delete Account if you are not running iOS 8) and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address back to the way it was. Now you can go to Settings>iCloud and sign back in with your current iCloud ID and password (your data will download back to your device). -
The IMAP server ... rejected the password for user ...
When I went to bed last night, Apple Mail (Lion, MacBook Pro) worked fine on my home IMAP server, as they have done for some time.
This morning, I cannot log in and I now get the following error message:
The IMAP server “...” rejected the password for user “...”.
The password is definitely correct. I have typed in the password repeatedly (although it was already correct) to no avail - I just get the same error message again.
Since then, I have tried:
my Linux laptop using Thunderbird
my Xoom (running Android ICS) and K9
my SGS2 (running Honeycomb) and K9
my iPad 2 using IOS Mail
Roundcube (webmail client) on the MacBook Pro itself (so no connectivity issues)
and all still work perfectly. There have been no changes to my mail server (which is Dovecot running on Debian Squeeze, which has been running flawlessly for years) and none to my MacBook Pro (unless they were silent).
I have tried deleting all the relevant items from my keychain, but that has made no difference either.
Any ideas because I'm stumped?Since I posted this, there has been more, but slightly different, weirdness.
In the middle of a session yesterday, Apple Mail started to do something different. When I typed in the password, it briefly worked (downloading one or two messages) and then the error dialogue box popped up again so clearly the password was always correct.
A short while later, it accepted the password and stopped complaining until ten minutes ago. This time I only had to type in the password once and it is working at the moment but who knows how long for? -
Agent state changed to reserved but call is not ringing/landing for 30 seconds
Hi All,
we have IPCC 8.5, CVP 8.5, UCM 8.5, last few weeks we are facing
agents are facing intermittently, their state changed to reserved but call is not landing/ring for a while, and we have seen call is going to RONA in CVP logs.
We have cross checked the Device Target (4 CVP servers) its fine, Queue music is interruptable.
In Ingress/VXML gateway we have the dial-peer pointing to two subscribers with equal priority. Seems to be some call is not routing to agent phone (delay is there between voice gateway and ip phone) due to some reason. We dont use SIP proxy we use static routing to subscribers.
Please share your ideas.
with Regards,
ManivannaIn Ingress/VXML gateway we have the dial-peer pointing to two subscribers with equal priority.
The gateway should point to the Call Servers. The Call Servers should have static routes to the subscribers.
If the call is not getting to the agent even though they go into Reserved (the Call Router has selected them), ensure that the SIP trunks to the Call Servers and the agent phones are in compatible partitions/CSS. Examine the logs on the Call Server when the INVITE is sent to the agent phone. If the INVITE returns 404 (not found) or 503 (unavailable), then the setup is wrong.
Regards,
Geoff -
My computer had to be shut down this morning when I could move my mouse around but it would not respond when I double clicked on an item to select. Now I cannot open a file in my finder window by double clicking on it. Any suggestions?
Did you reinstall CS3 after CC?
For that matter, doing an in-place upgrade on the OS is always a gamble with Adobe programs. Reinstalling all the versions you need, in order, would probably solve your problem.
And you shouldn't need to save as IDML after opening the .inx in CC. -
Can we disable the ability for users to sites and subsites in their SharePoint 365 Profile Site?
We have plans to roll out a hybrid SharePoint with our profiles in the Cloud. Does anyone know if it is possible to disable the ability for users to create sites under their Profile site in the cloud? As it stands out of the box, it looks like every
user can create as many sites as they want under their Profile. There is a concern that users will "self-service" their own solutions without going through the proper channels of governance. Has anyone had to deal with this or have experience
on how to restrict this functionality? Thanks in advance! :)HI Ken,we can disable this by blocking the self service site creation option.By default its disabled.
To disable the "Self-Service Site creation" option, just follow the steps given below:
1. Go to the Central admin.
2. Go to the "Application Management" & Select the specific web application.
3. Now, you can see the "Self-Service Site Creation" option in the Ribbon Menu.
4. Click on that Menu item and Select the "Off" option in the pop-up window
http://expertsharepoint.blogspot.de/2014/06/your-personal-site-cannot-be-created.html
Anil Avula[Partner,MCP,MCSE,MCSA,MCTS,MCITP,MCSM] See Me At: http://expertsharepoint.blogspot.de/ -
I have a analog to DV converter that I have had for years, but I have not used it for awhile, and I am using a newer MAC. How do I get it to import from my converter. When I go to import in iMovie it is only showing the built in camera. Help...
Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Mail: The POP server rejected the password for user
I am completely unable to use Mail.
I keep getting the "The POP server rejected the password for user" on two of my accounts.
The password has not changed and I have entered it correctly.
The accounts just will not go online.
This started yesterday when an old machine accidentally fired up mail and tried to connect using the same user details. Since then, my MacBook Pro is not able to connect to my mail.
My iPad and my iPhone can. There is no problem at the server or the ISP. I have also run the Keychain repair utility.
Please can you advise how I should fix it? Plist? Define the accounts again?
Any ideas welcome.
ThanksSorry I can't be of help, I know of others with this problem. In my case I have two accounts that don't work in Mail whilst the other accounts do. I suspect it may be a bug as I've been looking for a solution for sometime. My current solution is to collect the mail on those accounts with an XP netbook which is probably not very helpful!
I have also tried the Keychain repair and at least for a short while it looked as if it had fixed it.
Any ideas anybody before I go through the hassle of reinstalling everything?
D -
i have a g4 running os10.4.11, i bought a epson workforce 1100 and tried to set it up but there is not a listing for it when i try to add it before installing the driver software from the supplied cd...anyone know what i can do to get it set up?
Load the drivers and you should then be able to add it in Print Center.
Maybe you are looking for
-
Hi Experts, I did my application in jdev 11.1.1.6 and deployed using Jdbc Url connections and it worked successfully (Actually I m working with 2 diff Database connectiosn in my application) But the thing is my company need me to do something like I
-
Impossible to delete an item number of a PO of the previous year
Hello, I have a question. Closing Operations (Carryforward of Open Items) were not made yet. We want to delete in 2011 an item number of a purchase order (created in 2010 with doc date of the year 2010). The System informs us that It is not possible
-
No additional information - see below
-
Page breaks and 'Fit Page in Window' option
This may seem a stupid question but indulge me: when I add a page break InDesign is only showing me the very top of the text frame on the page the cursor has moved to. How do I get InDesign to honour the 'Fit Page to Window' option when I add page br
-
This is regarding GR Message Type WE03 As part of Global template GR form for message we03 is already exists .. we need to develop new form for current roll-out , initially we decided to have a our own GR custon message for this purpose But when i se