Landing page error, no server connection

I have exactly the same issue as the original poster below, I spent 3 hours of my only night off during the week of which 1 hour was in the chat que, an hour later and still no better, apparently there may be a problem at BT end. Brilliant service BT well done. I don't want the landing page, I just want my emails back before I just decamp to Virgin Media, and it's oh so tempting!,
Sort this out please....

The only way would normally be to check the BT outages page but if you look through the thread immediately above this one in the list (it's called "cannot connect to mail server") you'll see that BT/Critical Path  in their wisdom (or should that be ignorance - in the sense of not knowing what is going on) seem to no longer be posting any outages on their own websites. What a state of affairs for the prime service provider in the UK to have come to this nadir of customer care. BT you really should be ashamed of yourself. And I notice that some subscribers who have had their emails disrupted have been offered a free month for their broadband - is this going to apply to all of us??? Note that I'm not holding my breath.
Mistakes and embarrasing goofs in e-mails are only discovered when you've sent them!

Similar Messages

  • Still not working. Landing page error

    Hi, my Email is still not working. I was migrated last week, changed password as instructed and everything was ok.
    Since it went down I can still log in but get this pop up
    An error occurred while reading your landing page settings. Can't switch to preferred landing page
    If I click settings then mail  I get this
    An error occurred while reading your landing page settings. Please try again later
    I saw a link in aother thread where you put your Email in and it tells you which service you're on and I get a not recognised message.
    I did the live chat help yesterday around this time and was told it would be be passed to a supervisor as a matter of urgency and fixed within 24 hours.
    Any suggestions?

    This has turned into a complete and utter farce now.
    I was able to access my email through windows live, and also on my tablet after doing a manual setup.
    Yesterday Evening, almost exactly on the 48 hours to the second since previous call, BT phoned me.
    "can you please log into bt.com"
    "ok, done it"
    "click on email"
    "done it, same landing page error message"
    "I'll put you on hold while I look it up"
    10 minutes later
    "hello I'll pass it on to technical team, someone will call you back
    "pardon?"
    "I am informing technical team, they will call you"
    "when?"
    "they will call sometime, have a good evening"
    5 minutes later phone rings, same person "log in and describe screen so I can tell technical"
    "they took screenshots the other day"
    "tell me what is on screen"
    I did it and he went, again saying technical would call me.
    No further to solving it and as from later on last evening I can no longer acces mail through Windows Live or my tablet, I'm getting wrong password message, can still log on bt.com though.
    When they try to take my next monthly payment from bank BTare going to get the message  "access denied"

  • Page error causes server to crash

    These are the symptoms: we start loading a page and Oracle launches a process that hogs as much CPU as it can, slowing everything on the server to a near standstill. If we don't catch it within about 5 minutes, we cannot even log on to kill the process. Within a short space of time the OS is paging like crazy, and within about 10 minutes the 4GB of physical memory and 8GB of swap is all used up. The page never loads, and a few minutes after starting to load the page we get a 404 error. What happens after the available memory falls to zero is unpredictable but never good.
    Our APEX/Oracle environment is as follows:
    Product Build: 3.0.0.00.20
    Language Preference: en-gb
    NLS_CHARACTERSET: WE8ISO8859P1
    DAD CHARACTERSET: ISO-8859-1
    Oracle Database 10g Enterprise Edition Release 10.2.0.1.0 - 64bit
    PL/SQL Release 10.2.0.1.0 - Production
    CORE 10.2.0.1.0 Production
    TNS for Linux: Version 10.2.0.1.0 - Production
    NLSRTL Version 10.2.0.1.0 - Production
    OS: Red Hat Linux ES4 64bit
    First, I have to hold my hands up and say that it's always caused by an error that we have made, but often these are relatively trivial errors on the page that APEX will either gloss over or handle correctly 99 times out of a hundred (and certainly nothing obvious like an infinite loop). These kinds of problems also occur very rarely (thankfully), but what gets me is why the result is quite so catastrophic. I should also say that we're talking about a development environment containing very little data - the example we tested is a page with 3 report regions each based on fewer than 100 rows of data, comprising around 20 numeric columns, some dates, flags and audit information.
    What I'm keen to understand is whether this is a consequence of Oracle misconfiguration, or if there is anything else (other than never making any coding errors) that we can do to stop this from happening.
    These are examples of the kinds of errors that have that lead to the above symptoms (although not necessarily to the output listed below):
    1. Deleting a page item that a PL/SQL function within a page region references, without removing that reference. Mostly APEX will ignore such errors, treating the item value as null, but the difference seems to be where the item had a value in session state, and we did nothing to clear it after deleting the page item, although I suspect that this isn't the whole story, as this scenario doesn't predictably lead to the problem we're occasionally seeing.
    2. Returning SQL from a PL/SQL function that did not correspond either with the report template in use (for example dummy SQL (within an error block) that doesn't match the report template we're using (for example a column needed for conditional row formatting is missing)), or with the report definition (numbers and attributes of columns displayed - sorry I can't be very specific on this score, but in these cases deleting and recreating the report region with the same source has cured it).
    3. Other errors in the region PL/SQL source, such as referring to the wrong package when declaring a type, causing a type mismatch error.
    The latest page we had this problem with was returning SQL from a packaged PL/SQL function, in which creating a SQL block had thrown a 'character string buffer too small' error, and returned a dummy SQL string that did not contain a header column referenced in the report template, although some supposition has gone into that, as the focus was more on fixing the problem than pinning down its exact cause.
    The Apache logs don't tell us a great deal, other than that the server is in a great deal of trouble. There is nothing to indicate the start of the problem, but after a while we gets lots of entries like this:
    [<date/time>] [warn] [client <ip>] mod_plsql: Long running URL [pls/htmldb/wwv_flow.accept] timed out
    Later we get lots of:
    [<date/time>] [error] [client <ip>] [ecid: 1248707261:<ip>:24047:0:1,0] mod_plsql: /pls/htmldb/f HTTP-503 ORA-3113
    And a few:
    [<date/time>] [warn] [client <ip>] [ecid: 1248707264:<ip>:24081:0:1,0] mod_plsql: DMS Logging: Unable to read data from <Apache path>/Apache/modplsql/cache/modplsql.lck
    Plus a smattering of:
    [<date/time>] [error] [client <ip>] [ecid: 1248707384:<ip>:25588:0:6710,0] mod_plsql: Database (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=<server name>)(PORT=1530)))(CONNECT_DATA=(SERVICE_NAME=<service>))) Failed (time=10190ms rc=-1 ORA-1013)
    [<date/time>] [error] [client 10.100.36.48] [ecid: 1248707384:<ip>:25588:0:6710,0] mod_plsql: Failed to reset database connection (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=<server name>)(PORT=1530)))(CONNECT_DATA=(SERVICE_NAME=<service>))) rc=-1 ORA-1013 ORA-01013: user requested cancel of current operation\n
    [<date/time>] [warn] [client <ip>] [ecid: 1248707384:<ip>:25588:0:6710,0] mod_plsql: Discarded pooled connection (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=<server name>)(PORT=1530)))(CONNECT_DATA=(SERVICE_NAME=<service>))) because of ping failure
    On the database side, it's difficult for us to figure out what's happening, but it looks like APEX is trying to run an error-handling routine, which makes sense, but it does appear to be locked into a try-fail-retry cycle. We loaded an APEX page that had previously exhibited those symptoms with the DBAs running a trace, and the highlights of the TKPROF output were:
    This SQL: SELECT MESSAGE_TEXT, DECODE(MESSAGE_LANGUAGE,LOWER(NVL(:B3 ,:B2 )),1,0)
    MESSAGE_ORDER
    FROM
    WWV_FLOW_MESSAGES$ WHERE SECURITY_GROUP_ID = 10 AND (MESSAGE_LANGUAGE =
    LOWER(NVL(:B3 ,:B2 )) OR MESSAGE_LANGUAGE = LOWER(SUBSTR(NVL(:B3 ,:B2 ),1,2)
    )) AND NAME = UPPER(:B1 ) ORDER BY 2 DESC
    was run approx 45,000 times, returning no rows.
    This SQL: SELECT MESSAGE_TEXT, DECODE(MESSAGE_LANGUAGE,LOWER(NVL(:B5 ,:B4 )),1,0)
    MESSAGE_ORDER
    FROM
    WWV_FLOW_MESSAGES$ WHERE FLOW_ID = NVL(:B7 , :B6 ) AND (MESSAGE_LANGUAGE =
    LOWER(NVL(:B5 ,:B4 )) OR MESSAGE_LANGUAGE = LOWER(SUBSTR(NVL(:B5 ,:B4 ),1,2)
    )) AND SECURITY_GROUP_ID = DECODE(NVL(:B2 ,0),0,:B3 ,:B2 ) AND NAME =
    UPPER(:B1 ) ORDER BY 2 DESC
    was also run approx 45,000 times, returning no rows.
    This SQL: SELECT M.MESSAGE_TEXT
    FROM
    WWV_FLOW_MESSAGES$ M, WWV_FLOWS F WHERE M.NAME = UPPER(:B2 ) AND
    M.MESSAGE_LANGUAGE = F.FLOW_LANGUAGE AND F.ID = :B1 AND M.SECURITY_GROUP_ID
    = 10
    was also run approx 45,000 times, returning no rows.
    This SQL: SELECT DECODE(MESSAGE_LANGUAGE,'en-us',0,1) WEIGHT, MESSAGE_TEXT
    FROM
    WWV_FLOW_MESSAGES$ WHERE NAME = UPPER(:B1 ) AND SECURITY_GROUP_ID = 10 ORDER
    BY 1 ASC
    was also run approx 45,000 times, returning 1 row per execution.
    This SQL: SELECT PLUG_SOURCE
    FROM
    WWV_FLOW_PAGE_PLUGS WHERE ID = :B1
    was run nearly 13,000 times, returning 1 row per execution.
    This SQL: SELECT USER_ID
    FROM
    SYS.ALL_USERS WHERE USERNAME = UPPER(:B1 )
    was run nearly 6,500 times, returning no rows.
    This SQL: SELECT MESSAGE
    FROM
    WWV_FLOW_DEBUG WHERE ID = :B1 ORDER BY SEQ
    was also run nearly 6,500 times, returning no rows.
    And so it goes on. Later we have:
    SELECT ID, CURRENT_TAB, CURRENT_TAB_FONT_ATTR, NON_CURRENT_TAB,
    NON_CURRENT_TAB_FONT_ATTR, CURRENT_IMAGE_TAB, NON_CURRENT_IMAGE_TAB,
    TOP_CURRENT_TAB, TOP_CURRENT_TAB_FONT_ATTR, TOP_NON_CURRENT_TAB,
    TOP_NON_CURRENT_TAB_FONT_ATTR, HEADER_TEMPLATE, BOX, FOOTER_TEMPLATE,
    NAVIGATION_BAR, NAVBAR_ENTRY, SUCCESS_MESSAGE, BODY_TITLE, MESSAGE,
    TABLE_BGCOLOR, TABLE_CATTRIBUTES, REGION_TABLE_CATTRIBUTES, HEADING_BGCOLOR,
    FONT_SIZE, FONT_FACE, APP_TAB_BEFORE_TABS, APP_TAB_CURRENT_TAB,
    APP_TAB_NON_CURRENT_TAB, APP_TAB_AFTER_TABS, NVL(DEFAULT_BUTTON_POSITION,
    'TOP') DEFAULT_BUTTON_POSITION
    FROM
    WWV_FLOW_TEMPLATES WHERE ID = :B1
    executing nearly 6,500 times and returning 1 row per execution.
    and the same for this SQL: SELECT ERROR_PAGE_TEMPLATE
    FROM
    WWV_FLOW_TEMPLATES WHERE ID = NVL(:B3 ,NVL(:B2 ,:B1 ))
    Later we have some very obscure-looking data dictionary lookups.
    I'd be interested to know if anyone has any thoughts on what might be occurring, or what other information I should obtain to provide clues as to what is going wrong.
    Many thanks for your help.
    Regards,
    John.

    PLEASE READ THE FAQ FOR THIS FORUM.. Posting to threads this old is USELESS!! The participants are NOT going to be alerted to your question..
    Next time, post a NEW question, with a link to the old thread, ok??
    Also include some relevant information like:
    Database version (10g, 11g, XE, Standard, Enterprise)
    Web Server?
    Browser Involved?
    Heck, even posting sample code to oracle's hosted site would be helpful..
    Thank you,
    Tony Miller
    Raleigh, NC

  • Trying to setup email account - getting "server connection failed"

    I'm hoping someone out there can help me setup a POP account on my iphone. My host where the email account is based says it supports POP and/or IMAP, but I've tried to create a new account on the iphone with both methods and get the same message each time. The error says:
    Server Connection Failed
    The certificate for [email protected] may be invalid.
    I just setup the same email account in my microsoft outlook and it works fine. Any thoughts???

    Same problem here. We are running Exchange 2007 at my school and all I want is to get my mail sent to my iphone. I have no need to sync my iphone to my school computer.

  • IBM WPS: Error While Creating App and Int Server Connections in JDev 10g

    Hi,
    I have been struggling to create App Server and Int Server connections in JDeveloper 10.1.3.4 without any luck.
    The JDeveloper is present on VM ware machine from which I'm trying to establish the connections to remote server where SOA Suite 10g is installed on IBM Websphere.
    My Settings:
    App Server:
    Connection Type: Standalone OC4J 10.1.3
    RMI: tried WC_defaulthost port, 6003, RMI default port (How do I get the actual value of RMI on IBM Websphere and does this really make a difference?)
    Connection test fails with Mbean error. Ignored this error as documented in Installation guide.
    Int Server:
    Used the above App Server connection, gave the http port value of 9700 (also the WC_defaulthost on IBM Websphere)
    Connection test fails for App Server, BPEL PM Server and ESB Server.
    I have gone through other threads where different workarounds were suggested but none of them worked for me. The workaround of adding the property ipaddr with the value 0.0.0.0 in opmn.xml doesn't hold good here as IBM WPS doesn't have OPMN.
    Please suggest a working solution for this issue.
    Regards,
    CC

    The below message comes when you don't specify any default file for your webcenter portal application and this should not be any problem.
    Target Portal.jpr is not runnable, using default target index.html.
    Can you answer to my questions:
    1. Did you just created a new wcp application in jdev and ran it with out doing any changes? If you have done what are the changes?
    2. How did you ran your application? (right clicking a particular page or right clicking your portal project and selected "run" option?

  • Sys.webforms.page request manager server error exception:An unknown error occured while processing the request on server. The status code returned from the server was:0

    sys.webforms.page request manager server error exception:An unknown error occured while processing the request on server. The status code returned from the server was:0 We got this response(In firebug console) when we try to click on link (after leave webpage for 3 minuts ideal) which is AJAX based. Please reply ASAP because its urgent.

    Hi SP,
    Please check if the following web config appSettins value settings from SSRS server could fix the issue (Note, back up your original web config file before any modification).
    http://stackoverflow.com/questions/10911610/ssrs-webpage-error-status-code-500
    http://srinivasbn.blogspot.in/2013/09/syswebformspagerequestmanagerservererro.html
    http://connect.microsoft.com/SQLServer/feedback/details/782155/ssrs-2012-failed-with-win32-error-0x03e3
    If you have more questions about the SSRS error logs related to this issue, you can post in the SSRS forum for a better assistance with more experts.
    http://social.msdn.microsoft.com/Forums/sqlserver/en-US/home?forum=sqlreportingservices
    Thanks
    We are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Whenever I use a search engine, I keep getting the error message "The connection was reset while the page was loading".

    I am able to access the internet, but none of the search engines like Google, Yahoo or Bing will work. the page will not load. I get the error message:
    The connection to the server was reset while the page was loading.
    * The site could be temporarily unavailable or too busy. Try again in a few moments.
    * If you are unable to load any pages, check your computer's network connection.
    * If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.

    Your plugins list shows two Flash plugins and other outdated plugin(s) with known security and stability risks.
    # Shockwave Flash 10.0 r45
    # Shockwave Flash 10.1 r53
    # Adobe Shockwave for Director Netscape plug-in, version 11.0
    # Next Generation Java Plug-in 1.6.0_19 for Mozilla browsers
    Flash Player uninstall: http://www.adobe.com/go/tn_14157 (this will remove the Firefox Flash plugin and the ActiveX control for IE)
    Update the [[Flash]] and [[Shockwave|Shockwave for Director]] plugin to the latest version.
    *http://www.adobe.com/software/flash/about/
    *http://www.adobe.com/shockwave/welcome/
    *http://www.adobe.com/downloads/
    Update the [[Java]] plugin to the latest version.
    *http://java.sun.com/javase/downloads/index.jsp (Java Platform: Download JRE)
    Do a malware check with a few malware scan programs.<br />
    You need to use all programs because each detects different malware.<br />
    Make sure that you update each program to get the latest version of the database.
    *http://www.malwarebytes.org/mbam.php - Malwarebytes' Anti-Malware
    *http://www.superantispyware.com/ - SuperAntispyware
    *http://www.safer-networking.org/en/index.html - Spybot Search & Destroy
    *http://www.lavasoft.com/products/ad_aware_free.php - Ad-Aware Free
    *http://www.microsoft.com/windows/products/winfamily/defender/default.mspx - Windows Defender: Home Page
    See also "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked and [[Searches are redirected to another site]]

  • HP Photosmart 6520 Server Connection Error: -1: Apps don't work and Scan to email doesn't work

    My HP PhotoSmart 6520 has a persistent error to connect to the server and therefore Apps and Scan to email doesn't work.
    I have manually set DNS to 8.8.8.8 / 8.8.4.4, I have installed latest driver on my Macbook pro, I have updated firmware, but still not working. Weird is also that in my ePrintCenter, the Apps I see there are not in line with thos visible on the printer.
    Detail is that I have set up the printer on a Windows PC but recently changed to Mac.
    Printing, scan to Computer all works fine.
    Help! I have read a lot on forums but so far no solution for me!

    Hi Jack6520,
    Welcome to the HP Support Forums.  I see that you are unable to connect to the apps and use the scan to email feature of your Photosmart 6520 printer due to a server connection error.
    First off, thank you for the very detailed information, I really appreciate it.
    To better assist you, would you please provide some additional information:
    When you set the manual DNS servers, did you also set a manual IP address for the printer?
    Have you changed routers or internet service providers recently?  Have you updated the firmware on the router? If you have an ISP-provided router, do you know if they pushed out a firmware update?
    Have you recently installed any new anti-virus/malware software?  If so it may have blocked the ports the printer uses to communicate.  I’ve included a post by VisionAiry titled “Check the Anti-Virus for Blocked Ports and Timed Scans”. 
    Do you have a guest network setup? Please Print a Network Configuration page. It will let you know how many networks the printer sees. A guest network will have the same name as your network with a tag about it being the guest network.
    Previously did you customize the printer’s ePrint email address? I’m asking this because I might ask you to disable then enable the web services.  If we have to take this step you will lose the customized ePrint email address without any ability to get it back.
    What version of Mac OS X are you using? whatsmyos.com
    Are there any cables other than the power cable connected to the printer?
    Thank you.
    Regards,
    Happytohelp01
    Please click on the Thumbs Up on the right to say “Thanks” for helping!
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    I work on behalf of HP

  • SQL server connection error in sharepoint

     
    We are getting below error with inetgrated security and custom DB sql server connection in sharepoint 2013.
    This connectionstring works in dev with SQL username and password but in QA we are changing it to integrated authority.
    <add name="OurConnectionString" connectionString="Data Source=OurDB;Initial Catalog=Catalogname;Integrated Security=SSPI" providerName="System.Data.SqlClient"> (This does not work in QA)
    <add name="OurConnectionString" connectionString="Data Source=OurDB;Initial Catalog=Catalogname;User ID=user1;Password=ourpwd" providerName="System.Data.SqlClient" /> (This works in dev)
    at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)     at System.Data.SqlClient.TdsParser.TryRun(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader
    dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj, Boolean& dataReady)     at System.Data.SqlClient.TdsParser.Run(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet
    bulkCopyHandler, TdsParserStateObject stateObj)     at System.Data.SqlClient.SqlInternalConnectionTds.CompleteLogin(Boolean enlistOK)     at System.Data.SqlClient.S...
    c62c629c-6890-d0e5-d8a0-91d367f84202
    12/20/2013 10:29:31.55* w3wp.exe (0x2434)                      
    0x1EC0
    Unknown                      
    00000
    Unexpected ...qlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover)    
    at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer timeout)
        at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance)  
      at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnecti...
    c62c629c-6890-d0e5-d8a0-91d367f84202
    12/20/2013 10:29:31.55* w3wp.exe (0x2434)                      
    0x1EC0
    Unknown                      
    00000 Unexpected
    ...onString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString userConnectionOptions)     at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions
    options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions)     at System.Data.ProviderBase.DbConnectionFactory.CreatePooledConnection(DbConnectionPool
    pool, DbConnectionOptions options, DbConnectionPoolKey poolKey, DbConnectionOptions userOptions)     at System.Data.ProviderBase.DbConnectionPool.CreateObject(DbConnectionOptions userOptions)     at System.Data.ProviderBase.DbConnectionPool.UserCreateRequest(DbCon...
    c62c629c-6890-d0e5-d8a0-91d367f84202
    12/20/2013 10:29:31.55* w3wp.exe (0x2434)                      
    0x1EC0
    Unknown                      
    00000 Unexpected
    ...nectionOptions userOptions)     at System.Data.ProviderBase.DbConnectionPool.TryGetConnection(DbConnection owningObject, UInt32 waitForMultipleObjectsTimeout, Boolean allowCreate, Boolean onlyOneCheckConnection, DbConnectionOptions userOptions,
    DbConnectionInternal& connection)     at System.Data.ProviderBase.DbConnectionPool.TryGetConnection(DbConnection owningObject, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal& connection)    
    at System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal& connection)     at System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection
    outerConnection, DbConnectionFactory connectionFacto...
    c62c629c-6890-d0e5-d8a0-91d367f84202
    12/20/2013 10:29:31.55* w3wp.exe (0x2434)                      
    0x1EC0
    Unknown                      
    00000 Unexpected
    ...ry, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)     at System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry)     at System.Data.SqlClient.SqlConnection.Open()     at DBManager.ConnectionOpen()
    c62c629c-6890-d0e5-d8a0-91d367f84202
    12/20/2013 10:29:31.74 w3wp.exe (0x2434)                      
    0x1EC0
    SharePoint Foundation         Claims Authentication        
    aebgg High   
    MCTS Sharepoint 2010, MCAD dotnet, MCPDEA, SharePoint Lead

    Hi,
    According to your post, an error occurred when you connect SQL Server in SharePoint.
    We can do as follows:
    1. Try to replace Integrated Security=SSPI with Integrated Security=True
    2. Check whether there is <identity impersonate="true" /> under <system.web> tag in web.config.
    Here are two articles for you to take a look at:
    http://blogs.windwardreports.com/tomasr/2010/09/login-failed-nt-authorityanonymous-logon-integrated-securitysspi-vs-integrated-securitytrue.html
    http://www.layer2solutions.com/en/community/FAQs/BDLC/Pages/How-SharePoint-BDLC-used-with-integrated-security-trusted-connection.aspx 
    Best Regards
    Dennis Guo
    TechNet Community Support

  • Customise error page when content server is down

    Hi all,
    The following message is received when the content server is down:
    Web Server Error Error attempting to perform request. (Unable to connect to address.) To administrate this server use this link.
    I have seen a few variations fo this mesage on different conditions.
    The question is: how can we customise this page?
    Many thanks

    hi all,
    try this
    You can set up the maintenance page when at the Web server level when the application is down in the App layer. Here is the reference for Oracle HTTP server, same you can do it for any other web server too..!!
    You can achieve this by configuring an error page at the WebServer (part of web-tier).
    For example, in the case of a Oracle HTTP Server (OHS), you could do the following:
    1. Place your maintenance page at <ORACLE_INSTANCE>/config/OHS/<component_name>/htdocs.
    For Example, <ORACLE_INSTANCE>/config/OHS/<component_name>/htdocs/errorPage500.html
    2. Open the OHS httpd.conf located at <ORACLE_INSTANCE>/config/OHS/<component_name> in an editor and search for the string ‘ErrorDocument 403′ which can be seen as commented text. Next to the commented text line, add the below lines for configuring the Error
    Pages (500 —>  backend server unavailable, 403 —> forbidden request, 404 –> Resource Not available). For the below example, we had 3 html pages errorPage500.html, errorPage403.html and errorPage404.html are deployed in OHS htdocs.
    ErrorDocument 500 /errorPage500.html
    ErrorDocument 403 /errorPage403.html
    ErrorDocument 404 /errorPage404.html
    3. Save the changes to the httpd.conf file.
    4. Restart OHS server

  • Redirect to a custom error page when Forms Server shuts down

    Hi,
    I want the forms application to redirect to a custom error page whenever Forms Server goes down. (like network issues, unscheduled shutdown...) Whenever this happens, the user gets a pop up with FRM messages and user has to acknowledge the pop up. Since the application is used in the shop floor, there will not be any user always in front of the screen and will be a very big issue as there are at least 70-80 PC's on the floor which will be attended fewer times(only when there is issue with the machine) other wise the application displays important events of the machine,etc.,
    I am trying to develop a simple HTML error page(may be with applet) which will keep querying the forms server and once the forms server is up and running, the error page will revert back to the application which the user was working earlier to shutdown. Other option is the redirect to main menu of the application (this may be a PSP or a JSP or a Oracle Forms Menu ).
    Is there any event in forms to capture the loss of connection to forms server ??
    BTW, I am using Oracle Application Server 10g Forms and Reports on Windows 2000 Server...
    Any ideas...
    Thanks in advance
    Purush

    I don't think it will be easily possible in Forms for a couple of reasons.
    1. In Forms you do not have query rights, and as soon as you want to edit data, you have to log in. In Forms you log in once, and this sets your rights for the whole session. You will have to do some programming in Forms to achieve what you want. E.g. as soon as you hit the Save button you are asked for a username and password.
    2. A refresh cannot be done in Forms. Remember that Forms is a Java applet. The URL in the browser is just pointing to the startup page only. If you refresh your screen, you are taken back to the login screen of Forms again.
    Well, there will probably be ways around these problems. I'm thinking in the line of calling every form in a separate URL instead of starting a Forms application where one form is called from another form. The default 'query only' form can be called from a startup html page. This page can be refreshed. As soon as the user wants to update data, he clicks on a link or button and is taken to a login form.
    If the refresh is unsuccessful you are taken to a custom error page, like in your ASP application.
    A problem with an automatich refresh may be hanging sessions. Forms server does not always kill sessions.
    And also, how would you avoid a refresh if a user is currently using the form?

  • Download Server Connection Error

    I tried updating my desktop skype because it was being cruddy, but the updates wouldn't go through because of a "download server connection error." My friend suggested that I delete my old skype and reinstall it, but when I tried to do so, the same message popped up and offered a link to a supposed "solution." But when I clicked on it, it simply sent me back to the original page in a never ending loop of downloading failures. I looked up what to do, and it seems I'm not the only one with this problem. Others seemed to been having success when sent this link http://download.skype.com/msi/SkypeSetup_7.4.0.102.msi however, went to check it out, the page was deleted so I had no options. So now I'm stuck, and unable to download any program due to this error, which I have no idea what it is or how it's caused. If I could have some assistance ASAP, that would be great! I want my desktop skype back so I can share screens and see my friend while using my desktop. Thank you for your time, Chrissy. 

    On my computer and Internet connection it says it will download the file in 18 seconds but it downloads it in about 8 seconds.   I downloaded 3 copies in less than 30 seconds all over wireless.   If you are having issues downloading it you probably have a slow or intermittent Internet connection.  If you are going wireless try to move closer to your wireless router or go wired.

  • "server connect failed" error - CIT 400

    Would appreciate some help with this one:
    My CIT 400 handset does not seem to be able to connect to the base station. I get the error "server connect failed" when I try to sign in to Skype. No blue light flashing on the base station(during sign in or otherwise) either. Have tried resetting the base, resetting the handset, but no luck ...although the blue light on the base does flash once when it is reset. Any pointers please?

    Hi! do you have a PSTN line or landline plug-in to the device?  Can you receive landline calls from CIT400?  You may also try to access the setup page for the device and check the skype configuration.  Just enter the IP address of the device on your browser and use admin for the username an password.  Check on the Skype page the status of your account.  You may try different Skype account to check if it will work.

  • Chat gives error" Error trying to connect to the Server. The Server is not available, please try again later"

    I have installed the chat vu and the chat portal server. All the VU's are but still when i start the chat (ip address on the usl) and fill all the credintials, i get the error "Error trying to connect to the Server. The Server is not available, please try again later"
    I have tested the connection in the IIS ChatVU  and it is ok.
    Please guide !!!
    Thanks and Regards
    Rohit

    Hi Rohit,
    Did you change the \ChatAS\web.config file with the right IP address of you Chat Portal VU?
    For your referente check page 116 (Internal Chat Client) from "SAP BCM 7 SP5 Basic Installation Example" document.
    Regards,
    Heber Olivar

  • Getting - Active Server Pages error 'ASP 0126'

    I get the following error when applying the upload function
    to my already made form.
    Active Server Pages error 'ASP 0126'
    Include file not found
    /sitename/sitepage.asp, line 2
    The include file 'dwzUpload/DefineVariable.asp' was not
    found.
    The top of my code on "Sitepage.asp" looks like this:
    <%@LANGUAGE="VBSCRIPT"%>
    <!--#include file="dwzUpload/DefineVariable.asp" -->
    <!--#include file="Connections/connBest.asp" -->
    <%
    '* ONLY UPLOAD *
    http://www.DwZone-it.com *
    server.ScriptTimeout = 5400
    Dim RG_Connection, RG..........
    I can supply more information if need be. Your help is
    greatly appreciated!
    Thanks,
    Matt

    "dwzUpload/DefineVariable.asp" location is:
    C:\inetpub\wwwroot\sitename\dwzUpload.
    So it's located in the site root, inside the dwzUpload
    folder.
    I am currently running the site on my local machine with
    IIS7.
    I don't get an error if I remove the 'upload' function on the
    site, but the site needs to offer upload of image files. Not sure
    where to go to from here.
    Thanks,
    Matt

Maybe you are looking for

  • Thunderbolt SMS text errors after downloading update.

    So far, after downloading the newest update for the Thunderbolt on Thu July 14th, I have been having more problems with the phone than I have ever had before. It seems like I am now consistently having THREE different problems with the Messages compo

  • HElp required..plz...plz.help..fast

    hi frndz, i neeed ur help...i hav sum doubts ..plz answer.i hav nokia 3250 fone.. 1. u kno ders 1 hole wer we incert chargerwire 2 recharge batreee....the pin in dat hole is broken...ma doubtis dat whether it can b repared..?..is it so costly 2 reapi

  • After screensaver activates my aplications shuts down?

    Hi My new iMac computer shuts my applications down when the screensaver activates. When i return to my computer and enter my password, all my work i shut down, and i have to open all the applications again. How do I disable this "feature" ? Thanks, M

  • System preferences -Sound does not see external USB speakers

    The computer internal speakers are working OK but the problems come when I try to use external USB speakers. The previous volume problem of the imnternal speakers resolved itself. I have now purchased a new USB set of speakers (BOSE Companion 20) but

  • My i pod touch 2nd generation will not turn off

    My ipod touch 2nd gene. will not turn off. When I turned it on the screen is blue with the apple in the middle.  It has the little wheel thing underneath but its not turning or doing anything.