LAP 1142 not finding 4404 controller

My 4404 is has it's 4 gig ports connected to my 6509e via port-channel.
My 1142 is also connected to the 6509e and it set in vlan 11.
The management interface of my 4404 has an address in vlan 11 and is set to tag vlan 11.
When I power up the 1142, I can see it via cdp on the 6509e, but when I go to WCS and look at APs, it says none detected.
Any ideas?

1.  What is the firmware of the WLC?
2.  What is the error logs from the LAP and the WLC?
3.  Is the NTP server of the WLC set correctly?
4.  Can the LAP ping the Management IP address of the WLC?

Similar Messages

  • AP1242 Not joining 4404 controller

    Hi all
    Can anyone please help, my 1242 access points will not join my controller, I have done a debug and can see the Access point sending a discovery request, then the controller says discovery request sent, but then nothing happens, any ideas what this could be? I can ping the AP fine.
    cheers
    Carl

    There are a number of things that could cause the join request to not show up.  If there are no other controllers that the AP could be sending its join request to check to make sure there isn't a duplicate IP with your AP manager interface.  Next if you are running LAG make sure the port-channel load-balancing on the switch that the controller is connected to is set to src-dst-ip.

  • Aps not finding secondary controller

    I have just installed a secondary WLC 4402 where a client has 1121 APs and 1010 APs and I am slightly confused.
    We have 2 CISCO-LWAPP-CONTROLLER entries in DNS
    The WLCs are WLC1 and WLC2
    The 1010 APs fail over to the secondary controller perfectly well.
    The 1121 APs do not fail over.
    I have given the APs primary and secondary controller names of WLC1 and WLC2.
    Is this due to Option 43 not being configured correctly.
    I believe though I have not investigated that there is a single entry for the 1121 APs in the DHCP scope for option 43 of the original conmtroller but there is no entry for the 1010 APs.
    They are using the same DHCP scope in a layer 2 implementation.
    Any help appreciated

    When the ap has joined a wlc, the dns and dhcp option 43 is not used. The information created in the mobility group (mac address, ip address and mobility group name) is used. This is how ap's learn of the other wlc. Setting the ap's primary and secondary and or tertiary wlc is required for ap's to be able to join the other wlc. Option 43 and dns is used if the ap goes throught the proccess of finding a wlc if the primary, secondary and or tertiary wlc is not found. It seems to me that the ap's have properly joined a wlc, there for, you need to verify why the 1121'a are not joining the secondary.
    First of all, is the mobility group configured correctly and is ap fallback enabled or not. Also, verify that you can mping and eping the controllers. Is the wlc set to layer 2 or layer 3 mode? I think that the 1121 needs the wlc to be in layer 3, but I will check.
    What you should also do is console into the ap and post the log so we can see what errors the ap is getting.
    Here is a link. Search for layer 2
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6306/prod_bulletin0900aecd80321a2c_ps6521_Products_Bulletin.html
    Here is a link for AP Fallback:
    http://www.cisco.com/en/US/tech/tk722/tk721/technologies_tech_note09186a00807a85b8.shtml

  • 1131 and 1141 APs not finding the controller

    We have deployed about 40 of these and about half have found the controller. The others have not. I have used option 43 in the past but lately they were able to find the contrller without that. I also took out the lwapp-controller name out of dns as we have 4 buildings of these etc. Should I put the controller name in dns and what is that default name.
    thanks
    Gary

    If the AP's are not on the same subnet as the controller, and you are not using Over the Air Provisioning, then you need to use DHCP Option 43, put your DNS entry back in, or set the controller address manually via the console port on the AP.
    The host name for the DNS entry is CISCO-LWAPP-CONTROLLER. If you're adding that entry, then you might want to also add CISCO-CAPWAP-CONTROLLER pointing to the same address. While I believe that all current AP's will try to resolve CISCO-LWAPP-CONTROLLER (even if they are CAPWAP APs), this may not be the case in the future.
    We use the DNS feature and then set the AP's appropriate primary/secondary controller after it joins.
    Here's a good article about the AP join process:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
    Here's a good article about troubleshooting AP's that won't join:
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml

  • ACL migration Error : 1210 could not find a domain controller for domain "Test Domain" (Old Domain)

    Hi
    We are migrating from old domain to new domain. Before live migration, we are trying to check the ACE/ACL migration through SubInACL. We are running the SubInACL on a cluster, which is a member of the Old Domain (Test Domain). We are able to resolve and
    ping both Old Domain and the New domain from this cluster machine. We have created a network share on this cluster, which is accessible to all Domain Users of the Old Domain. Both Domains have two way forest level trust. we are trying to migrate
    the ACL of this share (\\ClusterMachine\testshare$) to the new domain using SubInACL. We are trying to run the below command to get it done.  
    subinacl /outputlog=C:\Users\Administrator\Desktop\Migrationlog.txt /subdirectories
    \\ClusterMachine\testshare$\*.* /migratetodomain=OldDomain=NewDomain=mappingfile.txt
    Mapping file contains : Domain Users=NewDomain_Users
    But we are geeting the Error that "1210 could not find a domain controller for domain "Test Domain". Error finding domain name : 1210 the format of the specified computer name is invalid. Current Object "\\ClusterMachine\testshare$"
    will not be processed."

    Hello,
    how in detail is DNS set up in each domain?
    Any problems when using nslookup to verify?
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://blogs.msmvps.com/MWeber
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
    Twitter:  

  • Did not find repository information for controller

    Hi Experts,
    We are getting following error in Production system. Could you please tell what can be the root cause behind it. I know when someone deploys this error comes. But in Production No one is deploying any Application.
    Please tell me what can be any other problem.
    Exception occured during processing of Web Dynpro application  /material_wd/ChangeRawMeridianApp. See exception stacktrace for details.
    [EXCEPTION]
    com.sap.tc.webdynpro.services.exceptions.WDRuntimeException: Did not find repository information for controller ChangePackManualCompView
    at com.sap.tc.webdynpro.progmodel.components.Component.getController(Component.java:572)
    at com.sap.tc.webdynpro.progmodel.components.Component.getController(Component.java:548)
    at com.sap.tc.webdynpro.clientserver.uielements.adaptbase.AbstractAdapter.findViewElement(AbstractAdapter.java:124)
    at com.sap.tc.webdynpro.clientimpl.html.client.HtmlClient.handleUIElementEvent(HtmlClient.java:2037)
    at com.sap.tc.webdynpro.clientimpl.html.client.HtmlClient.updateEventQueue(HtmlClient.java:550)
    at com.sap.tc.webdynpro.clientserver.phases.TransportIntoDataContainerPhase.execute(TransportIntoDataContainerPhase.java:48)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequestPartly(WindowPhaseModel.java:162)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.doProcessRequest(WindowPhaseModel.java:110)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequest(WindowPhaseModel.java:97)
    at com.sap.tc.webdynpro.clientserver.window.WebDynproWindow.processRequest(WebDynproWindow.java:512)
    at com.sap.tc.webdynpro.clientserver.cal.AbstractClient.executeTasks(AbstractClient.java:52)
    at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doExecute(ClientApplication.java:1549)
    at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doProcessing(ClientApplication.java:1363)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.delegateToApplicationDoProcessing(AbstractExecutionContextDispatcher.java:154)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.DispatchHandlerForAppProcessing.doService(DispatchHandlerForAppProcessing.java:35)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.AbstractDispatchHandler.service(AbstractDispatchHandler.java:127)
    at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:95)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.ExecutionContextDispatcher.dispatchToApplicationDoProcessing(ExecutionContextDispatcher.java:114)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:80)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.dispatch(ApplicationSession.java:618)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.dispatch(ApplicationSession.java:649)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doApplicationProcessingPortal(ApplicationSession.java:584)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doProcessing(ApplicationSession.java:311)
    at com.sap.tc.webdynpro.clientserver.session.ClientSession.doApplicationProcessing(ClientSession.java:743)
    at com.sap.tc.webdynpro.clientserver.session.ClientSession.doProcessing(ClientSession.java:258)
    at com.sap.tc.webdynpro.clientserver.session.RequestManager.doProcessing(RequestManager.java:259)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.delegateToRequestManager(AbstractExecutionContextDispatcher.java:202)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.DispatchHandlerForRequestManager.doService(DispatchHandlerForRequestManager.java:38)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.AbstractDispatchHandler.service(AbstractDispatchHandler.java:127)
    at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:95)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.ExecutionContextDispatcher.dispatchToDispatcherContext(ExecutionContextDispatcher.java:146)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:92)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:104)
    at com.sap.tc.webdynpro.clientserver.session.core.ApplicationHandle.dispatch(ApplicationHandle.java:275)
    at com.sap.tc.webdynpro.clientserver.session.core.ApplicationHandle.doProcessing(ApplicationHandle.java:71)
    at com.sap.tc.webdynpro.portal.pb.impl.LocalApplicationProxy.sendDataAndProcessActionInternal(LocalApplicationProxy.java:962)
    at com.sap.tc.webdynpro.portal.pb.impl.LocalApplicationProxy.sendDataAndProcessAction(LocalApplicationProxy.java:297)
    at com.sap.portal.pb.PageBuilder.updateApplications(PageBuilder.java:1638)
    at com.sap.portal.pb.PageBuilder.SendDataAndProcessAction(PageBuilder.java:361)
    at com.sap.portal.pb.PageBuilder$PhaseListenerImpl.doPhase(PageBuilder.java:2062)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processPhaseListener(WindowPhaseModel.java:220)
    at com.sap.tc.webdynpro.clientserver.phases.PortalDispatchPhase.execute(PortalDispatchPhase.java:52)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequestPartly(WindowPhaseModel.java:162)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.doProcessRequest(WindowPhaseModel.java:110)
    at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequest(WindowPhaseModel.java:97)
    at com.sap.tc.webdynpro.clientserver.window.WebDynproWindow.processRequest(WebDynproWindow.java:512)
    at com.sap.tc.webdynpro.clientserver.cal.AbstractClient.executeTasks(AbstractClient.java:52)
    at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doExecute(ClientApplication.java:1549)
    at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doProcessing(ClientApplication.java:1363)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.delegateToApplicationDoProcessing(AbstractExecutionContextDispatcher.java:154)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.DispatchHandlerForAppProcessing.doService(DispatchHandlerForAppProcessing.java:35)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.AbstractDispatchHandler.service(AbstractDispatchHandler.java:127)
    at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:95)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.ExecutionContextDispatcher.dispatchToApplicationDoProcessing(ExecutionContextDispatcher.java:114)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:80)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.dispatch(ApplicationSession.java:618)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.dispatch(ApplicationSession.java:649)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doApplicationProcessingStandalone(ApplicationSession.java:570)
    at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doProcessing(ApplicationSession.java:309)
    at com.sap.tc.webdynpro.clientserver.session.ClientSession.doApplicationProcessing(ClientSession.java:743)
    at com.sap.tc.webdynpro.clientserver.session.ClientSession.doProcessing(ClientSession.java:258)
    at com.sap.tc.webdynpro.clientserver.session.RequestManager.doProcessing(RequestManager.java:259)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.delegateToRequestManager(AbstractExecutionContextDispatcher.java:202)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.DispatchHandlerForRequestManager.doService(DispatchHandlerForRequestManager.java:38)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.AbstractDispatchHandler.service(AbstractDispatchHandler.java:127)
    at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:95)
    at com.sap.tc.webdynpro.serverimpl.wdc.sessionctx.ExecutionContextDispatcher.dispatchToDispatcherContext(ExecutionContextDispatcher.java:146)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:92)
    at com.sap.tc.webdynpro.serverimpl.core.sessionctx.AbstractExecutionContextDispatcher.dispatch(AbstractExecutionContextDispatcher.java:104)
    at com.sap.tc.webdynpro.serverimpl.core.AbstractDispatcherServlet.doContent(AbstractDispatcherServlet.java:87)
    at com.sap.tc.webdynpro.serverimpl.core.AbstractDispatcherServlet.doPost(AbstractDispatcherServlet.java:61)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:754)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:847)
    at com.sap.engine.services.servlets_jsp.server.Invokable.invoke(Invokable.java:140)
    at com.sap.engine.services.servlets_jsp.server.Invokable.invoke(Invokable.java:37)
    at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:486)
    at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:298)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:396)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:385)
    at com.sap.engine.services.servlets_jsp.filters.DSRWebContainerFilter.process(DSRWebContainerFilter.java:48)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.servlets_jsp.filters.ServletSelector.process(ServletSelector.java:76)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.servlets_jsp.filters.ApplicationSelector.process(ApplicationSelector.java:243)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.WebContainerInvoker.process(WebContainerInvoker.java:78)
    at com.sap.engine.services.httpserver.chain.HostFilter.process(HostFilter.java:9)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.ResponseLogWriter.process(ResponseLogWriter.java:60)
    at com.sap.engine.services.httpserver.chain.HostFilter.process(HostFilter.java:9)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.DefineHostFilter.process(DefineHostFilter.java:27)
    at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.MonitoringFilter.process(MonitoringFilter.java:29)
    at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.MemoryStatisticFilter.process(MemoryStatisticFilter.java:43)
    at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.filters.DSRHttpFilter.process(DSRHttpFilter.java:42)
    at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
    at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
    at com.sap.engine.services.httpserver.server.Processor.chainedRequest(Processor.java:428)
    at com.sap.engine.services.httpserver.server.Processor$FCAProcessorThread.process(Processor.java:247)
    at com.sap.engine.services.httpserver.server.rcm.RequestProcessorThread.run(RequestProcessorThread.java:45)
    at com.sap.engine.core.thread.execution.Executable.run(Executable.java:115)
    at com.sap.engine.core.thread.execution.Executable.run(Executable.java:96)
    at com.sap.engine.core.thread.execution.CentralExecutor$SingleThread.run(CentralExecutor.java:314)

    Hi,
    Some one might be deployed WDJ application with controller name ChangePackManualCompView which is already exist in some other application with diff name space
    Did not find repository information for controller
    Thanks,
    Sreeni.

  • Unhandled Exception "Could not find any available Domain Controller"

    Hi,
    I keep on having exchange 2010 loosing contact to domain controllers.
    "Unhandled Exception "Could not find any available Domain Controller.". EventID 1. Once I restart the sever, this error disappear and reappear again after a few days.
    When I run AD setting, the result shows as below. Update version is currently as at 14.02.0342.003. And boths DCs have 100% uptime.
    PS C:\> Get-ADServerSettings | fl
    RunspaceId                                
    : 9392eb25-bcdc-462e-816b-2d5626c572a5
    DefaultGlobalCatalog                      
    : DC2.com.au
    PreferredDomainControllerForDomain        
    DefaultConfigurationDomainController      
    : dc1.com.au
    DefaultPreferredDomainControllers         
    : {DC2.com.au}
    UserPreferredGlobalCatalog                
    UserPreferredConfigurationDomainController :
    UserPreferredDomainControllers            
    RecipientViewRoot                         
    ViewEntireForest                          
    : True
    WriteOriginatingChangeTimestamp           
    : False
    WriteShadowProperties                     
    : False
    Identity                                  
    IsValid                                   
    : True
    Could you please help as this exchange server has our management team and their outlook keep on going offline.
    Thanking you in advance.
    Cheers,
    Pwint

    I have another issue. I was trouble shooting exchange bin folder for permission and as a result of it Exchange transport service stopped and couldn't restart. I quickly changed to local service account and able to restart. Fixed the transport roles folder
    permission but don't know the password of network service account so I can't change it back. I can send and receive emails internally and externally but I am worried that by running with local account maybe not recommended? Is it safe to reset network service
    password? Thanks. I am freaking out... Regards, Pwint

  • LAP not joining the controller

    Gents
    I have 1 AP out of ten not joining the controller. I connected the access point to the network and I checked its boot. the access point reaches LWAPP Discovery" and then give me console input. I hard reset the access point and I hard coded an IP address for the AP the AP joins the controller, but when I reset it to assign it to another controller it did not join again.
    why the discovery process is not showing the DHCP option 43 configured and DNS for CISCO-LWAPP-CONTROLLER configured on the DNS. All the access point is operating normally except this one. it has many certificate inside, why a hard reset did not work to solve the problem?
    Please advise
    Thanks,

    Does the LAP have a valid IP address?
    Can the LAP ping the WLC managment IP address?
    Console into the LAP and in enable mode, type the command "lwapp ap controller ".

  • Can not find out Ethernet Controler & SM Bus Controller Driver for P 1000-1404TU Notebook PC

    Hi ;
    I just purchase a laptop as subject, i installed window 7 64bit and some drivers, but remain 2 drivers as bellow i can not find out in HP Website
    Ethernet Controler (wire LAN adapter)
    SM Bus Controller.
    Could some one help me ?
    Many thanks .
    This question was solved.
    View Solution.

    Hi,
    Please try:
    1. http://ftp.hp.com/pub/softpaq/sp52501-53000/sp52799.exe
    2.  http://ftp.hp.com/pub/softpaq/sp56501-57000/sp56517.exe
      & http://ftp.hp.com/pub/softpaq/sp46501-47000/sp46748.exe
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Unable to execute Test-Mailflow cmdlet. Could not find any available Domain Controller

    I started receiving this error in SCOM while testing Exchange 2007 Mail flow. Normally the tests work just fine, and when I execute"test-mailflow" on the offending server, it works just fine. The alert doesn't have enough details to find out what
    is wrong. Can anyone help out?
    Alert Description:
    Unable to execute Test-Mailflow cmdlet. Could not find any available Domain Controller
    Environment: SCOM 2012 R2 UR4
    MP: Exchange 2007 MP, latest update
    Monitor: Exchange 2007 Test Local Mail Flow Monitor
    Brody Kilpatrick

    Hi,
    After you execute"test-mailflow" on the offending server, please also look into event logs to check is there any errors or warnings. SCOM is a tool to collect information, from my point of view, this message is collected from Exchange server, so
    you may need to check event viewer.
    In addition, please also make sure your Exchange environment is under monitored. And have you followed the Exchange 2007 MP guide to configure the MP?
    Make sure the Client Access Server is under monitored, you may check the Application Event log on the Client Access Server, and make sure there are no errors or warnings indicating a problem with the Client Access Server.
    Regards,
    Yan Li
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • 1142N will not connect to 4404 Controller

    I have a 4404 controller
    code:                  4.2.130.0
    I am trying to deploy the new Air-LAP1142N-A-K9 and I am getting:
    5
    Fri Jul 23 13:37:44 2010
    AP Disassociated. Base Radio MAC:c8:4c:75:ae:83:04
    6
    Fri Jul 23 13:37:37 2010
    AP Associated. Base Radio MAC: c8:4c:75:ae:83:04
    7
    Fri Jul 23 13:37:27 2010
    AP Disassociated. Base Radio MAC:c8:4c:75:ae:83:04
    8
    Fri Jul 23 13:37:20 2010
    AP Associated. Base Radio MAC: c8:4c:75:ae:83:04
    9
    Fri Jul 23 13:37:10 2010
    AP Disassociated. Base Radio MAC:c8:4c:75:ae:83:04
    10
    Fri Jul 23 13:37:04 2010
    AP Associated. Base Radio MAC: c8:4c:75:ae:83:04
    11
    Fri Jul 23 13:36:54 2010
    AP Disassociated. Base Radio MAC:c8:4c:75:ae:83:04
    12
    Fri Jul 23 13:36:47 2010
    AP Associated. Base Radio MAC: c8:4c:75:ae:83:04
    13
    Fri Jul 23 13:36:37 2010
    AP Disassociated. Base Radio MAC:c8:4c:75:ae:83:04
    14
    Fri Jul 23 13:36:30 2010
    AP Associated. Base Radio MAC: c8:4c:75:ae:83:04
    Currently we have 60 of the 1200 series APs
    Any help will be appreciated.

    Hi
    you should use 6.0.199.0 or 7.0.98.0 as recommended code for that  platform.
    6.0.196 and lower is not recommended.
    Regards

  • LAP 2702 %CAPWAP-1-ARP_ERROR: Could not arp the controller ip address, retry later

    I am reusing one of the AP which was previously connected to WLC2504. 
    So I rename the AP and reconfigure the IP address to point to a new WLC8510. The AP and WLC is under same vlan 252.
    At first it has joined the new WLC but it keeps disconnected from wlc and reconnect again after awhile.
    AP is showing this error :
    %CAPWAP-1-ARP_ERROR: Could not arp the controller ip address, retry later
    My AP ip address is 172.16.54.171/23
    If i try to ping the ip from the same subnet, the AP has no timeout. but if I telnet into this AP and ping to wlc, it is intermittent. 
    Any idea what is the issue?

    Rasika,
    I have the same issue on my home 2504 with these 2700 UX, I have tried code 8.0.100.0, 8.0.110.0 (Docs say this is the min version supported), and even 8.0.115.0 (latest available) still no dice. The AP won't register, and gives the error stated above. I am seeing 2 images available for the AP, the AP shipped with the later image but  I AP recovery isn't working because it say's unable to find image with XX in the name? I see the TFTP logs, and name the file accordingly no dice, then the unable to find file name -XX pops up too. As you know I am busy during the day this week, but let's jump on a skype and take a look later maybe you have seen something I haven't?
    For good measure, also attempted to join a 3650 here at the house IOS-XE 3.6 no dice, going to try 3.7 too tomorrow, It worked for the 3700 UX AP's we had??

  • I have a compaq 6200 pro i can not find the driver for SM bus controller.

    I down graded the 6200 pro with the i3 chip  to winXP and now I can not find the driver for the SM bus controller does this system have a sm bus controller?

    Hi: Please click on the device in the device manager. Then click on the details tab. Post the top string of characters you see. Those will identify the type and model of the missing device and I can send you the link to the drivers. It is either your AMT driver, TPM driver or IMEI driver. In the meantime, install the chipset driver and reboot if you have not done so already. http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=5037900&prodNameId=5037902&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=vc-88640-1 Paul

  • Cisco AIR -LAP-1142 status led continuosly blinking green

    hello all,
                I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined  in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

    continously blinking green
    This could mean that the AP hasn't joined the WiSM yet.
    Can you console into the AP?  If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

  • 1142LAP not joing the controller after conversion

    I have some remote 1142s that I converted to LAP last night.  They are not joing a WLC, but I they are online and I can ping them.  Telnet or SSH is disabled by default (WHY???). What can I do to figure out why these access points are not joining the controller?                  

    How are the APs getting IP address information and controller IP information?
    The APs have static IP addresses and should be getting controller IP info through DNS. There is an entry cisco-capwap-controller pointing to one of our WLCs and I can ping it from the switch where the AP is connected. I also have DHCP Option 43 setup should the LAP decide to relase its static IP and get a DHCP IP address.
    Your switch ports were probably configured as trunk ports. Have you changed them to access ports?
    The switchports were configured trunks. I've since changed one to an access port.
    Can the VLAN interface at the remote site ping the management interface of the controller?
    Not sure how to do this from the specific VLAN interface at the remote site.  I can ping the management interface from the switch that host the VLAN interfaces.
    What's the controller type and code?
    5508  ver 7.3.101.0
    Can you console into an AP, reboot it and capture the output and post it on here? I assume this will be a problem since they are remote.
    AP is in a remote location. YES THIS IS THE PROBLEM...
    I need to get several of these APs converted at several locations.  It's a roll of the dice with ever AP I try to convert.  Theres got to be an easier way that doesn't involve several road trips.

Maybe you are looking for