Laptop 9470 windows 7 not booting

The PC suddenly shut down. Now not booting up. It says windows failed to start. A recent hardware or software change might be the cause.
This lappy doesnot have cd disc slot. How should I try to reboot it.

Hi
When you start your machine tap F8 ( repeatedly) till you get to Advanced Boot Options .
Next using your arrow keys move down to Safe Mode With Command prompt hit enter
Next when Command prompt has started type sfc /scannow hit enter NB there is a space between c and /
Let Windows scan for errors ( may take some time ) once process has completed type Exit
Next use CTRL + ALT + DELETE and choose to restart your machine ...
Checkurtech
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Similar Messages

Window will not boot on the usb cd rom what should be done

window will not boot on the usb cd rom what should be done

Do you have that problem when running in the Firefox SafeMode? <br />
[http://support.mozilla.com/en-US/kb/Safe+Mode] <br />
''Don't select anything right now, just use "Continue in SafeMode."''
If not, see this: <br />
[http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes]

Windows will not boot

Hi,
I got after couple of years perfect comp. an terrible problem. The Windows will not boot, i can start it only with CD or sometimes i am getting message: how I wish to start Windows . I already tried to repair it, but no success. In the event log I could see only one notice : Service Control Manager event 7026, but this I had before with perfect comp.
Thanks in advance

Hi guys.
here i foud the cure:
* Power off the PC
* Power off the monitor
* Disconnect all cables from the monitor (USB, power, etc.)
* Disconnect all monitor cables from the PC (USB, VGA, DVI, etc.)
* While disconnected, press and hold the monitor power button down for 3 seconds
* Reconnect the power cord to the monitor
* Reconnect the monitor VGA or DVI cable to the PC video card
* Power on the monitor if it does not power on by itself
* Power on the PC
* Once into windows, open the Device Manager (Press the Windows key and the Pause-Break key)
* Click the Hardware tab
* Click the Device Manager button
* Click the plus by Universal Serial Bus Controllers (notate what is listed)
* Connect the USB Uplink cable from the bottom of the monitor to a USB port on the rear of the PC
* Under Universal Serial Bus Controllers, you should see additional Generic USB Hubs
* This means the monitors USB Hubs were seen by the operating system
Message Edited by DELL-ChrisM on 12-07-2007 02:47 PM

Bootcamp: Windows 7 not booting on 4gb ram

Hi!
Situation:
I installed Windows 7 via Bootcamp. On 2gb ram (2x1gb or 1x2gb doesn't matter) windows boots fine.
I upgraded to 4gb ram (2x2gb) and now Windows is not booting. As far as I know, it's not even getting in DOS.
There's just the cursor blinking into infinity...
What I've tried so far:
Installing windows with 2gb and ugrading to 4gb.
Installing windows with 4gb
Tried the 32bit and the 64bit version
Found a 'solution' on the web making me boot in safe mode in order to change the maximum ram windows accepts.
Attributed more gb to the windows partition
I'm out of ideas, what do you think?
regards,
Massimo

While we all have MacBooks in this forum not all of us use BootCamp. There's a BootCamp Support Community where everybody uses BootCamp. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/windows_software/boot_camp

Windows 7 not booting with 4gb ram

Hi!
Situation:
I installed Windows 7 via Bootcamp. On 2gb ram (2x1gb or 1x2gb doesn't matter) windows boots fine.
I upgraded to 4gb ram (2x2gb) and now Windows is not booting. As far as I know, it's not even getting in DOS.
There's just the cursor blinking into infinity...
What I've tried so far:
Installing windows with 2gb and ugrading to 4gb.
Installing windows with 4gb
Tried the 32bit and the 64bit version
Found a 'solution' on the web making me boot in safe mode in order to change the maximum ram windows accepts.
Attributed more gb to the windows partition
I'm out of ideas, what do you think?
regards,
Massimo

While we all have MacBooks in this forum not all of us use BootCamp. There's a BootCamp Support Community where everybody uses BootCamp. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/windows_software/boot_camp

Windows will not boot GTX 770

Hi there,
I recently bought new MSI gtx 770 lighting edition LE. When i choose in uefi as a primary gpu - PCIe, windows will not boot, and after few seconds screen goes black. If i go with primary gpu as integrated in processor i am ok to boot even i can play on monitor connected to GTX770. When i ran passmark benchmark, i get for VGA 3600 points, againt average 6300. Is there something wrong ? Thank you. Motherboard Asus sabertooth z77, cpu i53470k. PSU 600W, 8GB ram...

Silly questions as this should be a no-brainer, but have you installed specific drivers for the 770 from the geforce website?

Bootcamp - Changed partition settings now Windows will not boot

Hi,
I suspect I've created a problem that I've made progressively owrse in trying to solve... Any help appreciated!
A month ago I created a bootcamp partition (about 850Gig OS X and 150Gig for Win7), successfully installed Windows 7 and everything was fine.
After an acciental delete of itunes media incident I thought I would create a Time Machine backup partition on the OS X part of the drive so used the Disk Utility to do so, making sure I "took" from OS X and not the Bootcamp partition. I now had three partitions: OS X (500Gig), a Backup (350Gig) and a Bootcamp (150Gig) (I now suspect some of you might be screaming I've created the problem here already...) noting that the 150Gig Bootcamp partition is still as it was and the diagram in Disk Utility has always shown it as the bottom section.
Perhaps I'm being naive here but it never occured to me that splitting the OS X partition would have any impact at all on the Bootcamp partition!
Anyway, now I'm unable to boot to Windows (black screen "No bootable device" etc message).
Checking Finder, all the files on the Bootcamp partition still seem to be there - User settings/accounts, Program Files, the lot.
Is there anyway I can easily rectify this? (eg put the Windows 7 disk in and repair the install or something?!)
I tried deleting the extra Backup partition I created without luck (the space just gets greyed out and unallocated)
Help! I really don't want to have to go through the whole mess of reinstalling Windows 7 on to the Bootcamp partition (that to my mind still hasn't been touched!)

Your Boot Camp partition number probably changed, Windows does not like more than 4 partitions, you had 3 + Lion Recovery and one that Windows makes, and that is one too many.
You can try running Windows startup repair from the disk, but>
Before you do anything make a backup (a clone, for speedier disaster recovery)
If startup repair fails then reinstalling Windows is called for, so while you are at it I would repartition the drive completely, put your Lion installation back on the Mac from your clone, make a new prtition in Boot Camp and reinstall Windows. Then if you have backups of the Windows side (Windows Backup or similar) restore the data.

Problem: PC crashed windows 7 Not booting. toshiba sattelite A665-S6086 win 7 64bit.

Hi, please help.
I need to recover win 7, no media recovery disk, and HDD is not booting although I took off the HDD and connect it to other PC, I can see everything the HDD, seems no problem ( it has 3 partitions 1.4GB : recovery ( I cannot access it) and 450GB (Main drive- I can acccess all of the data) and 3rd partition.
I have satellite A665-S6086.
PC fell, screen is broken and windows will not start . I used external Monitor.
(system is: win 7 64 bit home premium-EN).
I don't have media dvd for recovery.
I tried another win 7 version, is booted from CD, but I did not contiue, because it is wrong version, and I need the same to be restored.
From bios setup it sees the HDD.
When I boot it on external monitor, it gives toshiba logo for short time and goes to curser screen and stops responding.
I want to restore the same version without getting on activation and drivers obstacles. How can I do that please??
thanks for your help in advance
amin

Satellite A665-S6086
That procedure is described in the section Recovering to out-of-box state (recommended recovery method), which begins on p. 63 of the User's Guide.
Satellite A660 Series User’s Guide
Be sure to burn recovery discs as described on p. 70.
-Jerry

NForce 4.27 drivers + SB Audigy 2 ZS Platimun = Windows XP not booting!

Hi folks,
I know that I'm not using my MSI K7N2 Delta in my main rig anymore, but I've gotten good help here in the past (you guys rock!), and I *do* have the MSI GeForce 6800GT in my config so I was hoping that you folks might be able to give me some insights.
I have a system with the following components:
DFI Ultra Infinity nForce2 Ultra motherboard (latest BIOS)
2 x 512MB OCZ PC4200
Mobile Athlon 2500+
MSI GeForce 6800GT (Forceware 61.77)
PCI Slot 3 Intel 10/100+ PCI NIC
PCI Slot 4 (not shared) - SB Audigy 2 ZS Platinum - Assigned IRQ4 manually
All on-board peripherals disabled except for FDC, IDE1, USB
After much gnashing of teeth, (and several reinstalls of Windows XP) I narrowed it down to a problem between the nForce drivers and the Audigy 2 ZS drivers.
I'll tell you what happens:
When I install Windows XP, everything is great. Everything loads up just fine. I can get Windows installed without a hitch. I then upgrade to SP2. No problems. I then try installing the nForce UDP 4.27 and it works with no issues. I can even install the drivers for my GeForce card and, again, no problems at all.
However, if I then install the driver software for the Audigy 2 ZS Platinum, the system will no longer boot into Windows XP!
If I do the reverse, as in install the Audigy 2 ZS Platinum drivers FIRST, the system is fine until I try installing the nForce UDP 4.27, then the same thing happens.
There is little recourse but to reinstall Windows (I'm not doing an ASR if I can avoid it as they're messy) in either case because I can't even get into SM w/ CP.
When Safe Mode shows the drivers loading the system hangs at MUP.SYS then never continues.
I Googled the problem and I found a bunch of suggestions about how to avoid conflicts with the Audigy cards, and I assigned Slot 4 to IRQ4 and no other device is conflict/sharing with it.
On a note: I actually DID manage to get the Audigy and nForce drivers to work properly to allow me a clean reboot, but that was before I realized that I'd forgotten to power up the Live! Drive. When I shut down and powered up the Live! Drive, the system wanked on startup. Even removing the Audigy 2 card did not allow Windows XP to boot up after this happened.
I guess my questions are:
1) Has anyone ever run into this before?
2) Does this sound like a problem with SP2 acting wanky? Should I just try installing the nForce/Audigy software on the base Windows XP and see what happens?
3) Do I NEED to install the nForce 4.27 drivers, or is there another version that you can recommend that might be more friendly, or do I even need to install them at all? What parts of the nForce driver do I absolutely need to install if I must do so?
PLEASE NOTE: This setup worked fine with a SB Live! Platinum 5.1 in the same slot prior to me upgrading to the SB Audigy 2 ZS Platinum (and the old sound card worked great on my old K7N2 delta). However, I was also not trying to run SP2....
Any help that any of you gurus out there can give me would really be appreciated. I'm at the end of my rope here.
Thanks

Quote
Originally posted by Tango
APIC on or off?
When u install the nforce drivers if you havent already done so DO NOT install the ide drivers and see what happens.
I have APIC on, as well as ACPI. I have also manually assigned IRQ4 to the slot with the Audigy card and it's not shared. I disabled the onboard serial ports, parallel port, firewire, NIC and audio.
It is worthwhile to note that when I installed the Audigy 2 ZS Platinum drivers FIRST, that all devices in the system functioned properly and without problems. It wasn't until I upgraded the system drivers for the nForce components that it refused to boot. This would seem to indicate a conflict between these sets of drivers, and not an IRQ problem or hardware resource conflict.
Could it maybe be SP2 doing it? Should I try installing as Wonkanoby suggested below with no service packs or SP1a?
Quote
Originally posted by Wonkanoby
put the drivers in a folder and unrar them
for starters you can delete the 2x audio folders if not using them
you have turned the onboard sound of in the bios
the new installer will also let you install them one at a time
so you can try and find what ones doing it
http://forums.pcper.com/forumdisplay.php?f=66
http://www.nforcershq.com/forum/viewforum.php?f=64
would be worth a read and an ask as wellQuote
Thanks Wonkanoby. I appreciate the links, and yes, I'll try to install the nForce drivers one by one. I'll create Restore Points for each one and figure out where it's dying. Someone else on another forum suggested disabling MUP.SYS as it seems to be hanging there, but it could just coincedentally be the last item loading BEFORE it blows up.
Thanks for everything :D

Windows installer not booting up after resizing the partition

Hello.
I am trying to reinstalling Windows 8.1. pro on my macbook with Yosemite.
When I initially installed Windows, it went fine, but Windows corrupted my booting process.
So I tried to fix it with gdisk command to create hybrid mbr, but I was not able to fix the problem.
So I deleted the Boot Camp partition using Boot Camp Assistant.
then I created a new Boot Camp partition through Boot Camp Assistant.
However, Windows installer did not boot up automatically nor manually(pressing option whilst booting) anymore.
I have booted up Windows installer using the same usb on pc, so I know that the usb containing Windows installer does work..
I am not sure how to boot the Windows installer.
Do I have to do clean install the OS X??
thank you for your help and time in advance.
Rin

Is it possible to create the disk using BCA and a Windows ISO on the Mac, if your Mac supports it? If your Mac has a built-in Optical drive (or used to have one), you are going to run into issues.
Can you
1. Run Disk Utility Repair.
2. SMC Reset - Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
3. PRAM Reset - OS X Yosemite: Reset your computer’s PRAM
You can also look at Bootcamp Windows 7 Install Problem.

Windows 7 not booting

Hi, I've got a c660/c660d laptop and the windows doesn't boot. I've tried everything even pressing power on plus the zero key. It always comes back to launch repair. But if I do that a black screen with an arrow comes out. I've got system recovery disc 1 &2 but still it doesn't work. Please help me.

Are you able to see the BIOS screen?
Do you seen the Windows LOGO at all?
On the black screen, are there any error numbers?
Does it shut off by itself?
Also the complete model number helps.
-Kenna
"Knowledge should be unrestricted and the most important commodity we can offer to help one another."

Windows does not boot on new motherboard

Hi everybody.
I am lost here.
I made an upgrade to my PC: replace motherboard, CPU and RAM. Keep everything else.
I went from a celeron400 w/ intel chipset to 865 neo-2 PFISR.
The BIOS run fine. I can boot on CDs. But windows refuses to boot from c:. It looks like the MBR is fine, because I get the screen that says: "windows failed styarting, how do you want to start, fail safe mode or normal mode?" From here, any option I choose reboots the PC very quick.
I think the problem is that the geometry (CHS) of my disk is wrong. But I don't manage to find the correct values.
Does anyone has any idea of what is going wrong?
- The hard drive is a 15GB IBM DTLA 703015 (desktar 75GXP)
- I don't want to format everything....
- The drive still works on other computers.
Additionnal question: any link to installation of Windows XP pro on a SATA disk?
Thank you for any idea you might have!

In bios under Integrated Peripherals, On Chip ATA Operating Mode set
Native Mode
ATA Configuration - PATA only
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
You can't boot using a hard drive with windows installed on a different motherboard. There are too many differences to be successful.
Connect the SATA drive to SATA1, don't connect any PATA drives, and use the settings above. After you install Windows you can connect up the PATA drives (if any) to use for data.

Windows will not boot. Recovery media not working. Satellite L675D-S7052

I am using a Satellite L675D-S7052 with Windows 7. When the laptop is powered on, it will only run to the Windows loading screen (windows logo on screen) and will stop. The logo remains animated but it will not load any further.
I attempted to reset to factory settings using the recovery partition. It will run through "Windows is loading files" to completion, but it will then go to a blank screen with only the mouse cursor showing.
Finally, I attempted to recover from recovery DVD's I made previously. It loaded through the same screens as the recovery partition, halting again on the blank screen with the mouse cursor.
I backed up all important files on an external hard drive already. I was able to successfully boot an Ubuntu 12.04.2 live disk and it ran correctly. I can access the files on the hard drive for back-up from Ubuntu. I have not altered anything.
That's as far as I can go on attempting to fix this. If anyone can help me find my next step, please advise.

Hi! Sense you're not getting any replies, I will offer my opinion. Sense you can boot Ubuntu OS and it runs correctly,what else could be the problem but bad software?? You tried the recovery partition and the recovery DVD's and they reacted the same?? It's good that you can recover your important files. The recovery options are great, but a back up image on a external USB is your best protection. I just don't understand why people don't create a back up image of their OS. It's so simple!! When did you create your recovery DVD's?? Sense both recovery options act the same, I suspect corruption. That's the only thing that makes sense to me??
Dokie!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Satellite A110-293 Windows will not boot up. ntoskrnl. No recovery CD

I have a Toshiba Satellite A110-293 with Windows XP. I upgraded to Vista a few months ago. One day I turned on my laptop and got the following error message:
+"Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:+
+1. Insert your Windows installation disc and restart your computer.+
+2. Choose your language......+
+3. Click "Repair your computer"+
+If you do not have the disc, contact your system administartor or computer manufacturer for assisstance.+
+File ntoskrnl.exe+
+Ststus: 0xc0000098+
+Info: Windows failed to load because a required file is missing, or corrupt+
I do *not* have my original CDs or Vista upgrade DVD, since I'm overseas for a few months.
I tried to get a Recovery CD through the website (https://backupmedia.toshiba.eu/serial.aspx), but it stated:
+"For your device no recovery medium can be ordered, because it comes either not from the region of Toshiba Europe, or it is too old for this service. "+
HELP!

Hi
I presume you can order only the newer Toshiba Vista recovery DVD using this Toshiba website.
If you need a Recovery CD (Win XP) for this older Satellite series then you will have to contact the ASP (authorized service provider) in your country.
At the other hand you could use an original Microsoft XP CD to repair or to reinstall the OS.
By the way; did you try to boot the OS in safe mode pressing the F8?
Please check this. Maybe its possible.

Windows 7 not booting. Says File:\Boot\BCD error

HI, I have purchased a HP Pavilion DMZ1 XL303AV laptop. I had got it serviced from a HP service centre as it had suffered water spillage. The service centre replaced the entire motherboard. Now, the laptop suddenly stopped working. It gives an error message: File : \Boot\BCD; Status 0xc00000e9 ; Info: AN unexpected I/O error has occured. It says if you receive this error, please contact hardware manufacturer.
I donot have a Recovery CD for this model. HP did not provide. I donot remember creating a recovery USB drive for this (This model has no CD/DVD drive).
The machine is not working . Please help

Hi SyedAR, I am sorry to hear that you are getting this error on your computer. I would strongly suggest that you contact HP Total care at 1-800-474-6836 or at this link if the number is outside your calling area. http://www8.hp.com/us/en/contact-hp/ww-contact-us.html From what I can see from this error, you are going to need the recovery disks for the Windows operating system and you can get them from HP Total care. They will also be able to walk your through repairing your computer once you have the disks.
Thank you for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Laptop 9470 windows 7 not booting

Similar Messages

Maybe you are looking for