Laptop Appearing Not to Shut Down Sometimes

I have a 15 inch Macbook Pro Mac OS X 10.7.4. Sometimes after I unfold my laptop, I see the log in screen (the log in screen you'd get after the laptop goes to sleep). However, I should not be seeing this screen because I have shut the laptop down, not put it to sleep. A few seconds after unfold the laptop and seeing the screen, the screen turns grey and shuts down. Why is it doing this and how do I fix it? I'm very sure I'm actually shutting the laptop down.

Does the operating system on the laptop have to be shut down completely before the lid should be closed?

Similar Messages

  • Laptop battery not charging/shutting down abruptly

    Hi all,
    I have an Early 2011 Macbook Pro 13". Lately, it's battery is causing me problems. Can anyone point to me the problem. The system info follows:
    Battery Information:
      Model Information:
      Serial Number:    .................
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          165
      Charge Information:
      Charge Remaining (mAh):          1619
      Fully Charged:          No
      Charging:          Yes
      Full Charge Capacity (mAh):          4699
      Health Information:
      Cycle Count:          487
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          2247
      Voltage (mV):          11547
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          15
      Automatic Restart on Power Loss:          No
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      Standby Delay:          4200
      Standby Enabled:          0
      Battery Power:
      System Sleep Timer (Minutes):          15
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          15
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      Standby Delay:          4200
      Standby Enabled:          0
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          60
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x004505ee
      Charging:          Yes
    Power Events:
    Repeating Events:
      Type:          Wake or Power On
      Time:          12:00 am every day
      Type:          Sleep
      Time:          1:00 am every day

    Hello snavdeep,
    You may want to calibrate your battery.
    Apple Portables: Calibrating your computer's battery for best performance
    http://support.apple.com/kb/HT1490
    Cheers,
    Allen

  • Macbook froze while online. hard shutdown. when it restarted, an error message appeared saying finder shut down unexpectedly containing a message box with a long list of technical jibberish.  after clicking OK that it would send an error report to Apple,

    macbook froze while online. hard shutdown. when it restarted, an error message appeared saying finder shut down unexpectedly containing a message box with a long list of technical jibberish.  after clicking OK that it would send an error report to Apple, the same error message box appeared again and again every time OK was clicked.  Now the macbook will not turn on at all

    If you're able to boot, launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
    Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post "shutdownStall" or "hang" reports.
    If you can't boot in the usual way, try a safe boot. The instructions provided by Apple are as follows:
    Be sure your Mac is shut down.
    Press the power button.
    Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
    Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
    During startup, you’ll see a progress bar, and then the login screen, which appears even if you normally log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Safe mode is slower than normal, and some things won’t work at all.
    Note: If FileVault is enabled under Mac OS X 10.7 or later, you can’t boot in safe mode.

  • HT1199 my computer displays grey screen and apple logo for 10 minutes or more during start up and shut down. sometimes it refuses to shut down . this issues started after installing OS lion. what do i do?

    my computer displays grey screen and apple logo for 10 minutes or more during start up and shut down. sometimes it refuses to shut down . this issues started after installing OS lion. what do i do?

    I don't think it's exactly an incomplete installation brody, but most likely in-correct permissions somewhere along the line that either happened, or became magnified during the upgrade. Also, it could be corruption as well.
    First thing to do, is boot up holding down Shift key to do a safe-boot so we an clean up any corrupted OS caches, after that do another reboot, but go to the Lion recovery, and scan the HD for errors, repair any if you find them, and then try to do a Repair Permissions job.
    That should fix the issue, if not, we can start doing a PRAM reset  and SMC for good measure.

  • Ff 33 does not fully shut down

    My FF v 33.0 stays open in processes under task manager.
    All my other browsers do fully shut down.
    I have reloaded FF on my virus/malware free computer but FF will not completely shut down.
    Very annoying.
    Please help

    Hello,
    Try opening in [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] and see if the browser closes properly after opening in that. Safe mode is a troubleshooting mode that turns off some settings, disables most add-ons (extensions and themes). Since Firefox has trouble closing, make sure that it is not running in your Task Manager before opening in Safe Mode.
    If Firefox is not running, you can start Firefox in Safe Mode as follows:
    * On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
    When the Firefox Safe Mode window appears, select "Start in Safe Mode".<br>
    [[Image:Safe Mode Fx 15 - Win]]
    ''To exit Firefox Safe Mode, just close Firefox and wait a few seconds.''
    '''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
    When you figure out what's causing your issues, please let us know. It might help others with the same problem.

  • Database system was not properly shut down

    Dear Mac community,
    I have just repaired a friends 800 MHz 17" Flat Panel Display iMac... Somehow the hard drive had become badly corrupted and the system was frequently shutting itself down and freezing with kernel panics as a result. I managed to recover my friends data using Data Rescue II and after using Disk Warrior managed to do an Erase & Install of Mac OS X (10.4.4).
    The iMac appears to be fine now except for one worrying thing that I have noticed in the console each time after restarting:
    Mac OS X Version 10.4.4 (Build 8G32)
    2006-02-02 16:20:47 +0000
    2006-02-02 16:20:50.962 SystemUIServer[201] lang is:en
    LOG: database system shutdown was interrupted at 2006-02-02 16:19:46 GMT
    LOG: checkpoint record is at 0/87904C
    LOG: redo record is at 0/87904C; undo record is at 0/0; shutdown FALSE
    LOG: next transaction id: 550; next oid: 82855
    LOG: database system was not properly shut down; automatic recovery in progress
    LOG: ReadRecord: record with zero length at 0/87908C
    LOG: redo is not required
    LOG: database system is ready
    Does anyone have an idea what this might be and how I can resolve the issue??
    The systems performance doesn't appear to be affected in anyway however it looks and sounds ominous.
    One other small thing I have noticed is that the iMac won't automatically put itself into sleep mode despite it being set to in the Energy Saver System Preferences. There are no external hardware devices attached such as a printer, firewire device, USB hub etc. I have reset the PRAM and NVRAM and this appears to have had no effect.
    Any advice / suggestions greatly appreciated!!
    Many thanks,
    Justin

    Marking as answered as I managed to resolve the issue

  • My 5th ten iPod is basically doing nothing but trying over and over again to start up. I've tried to restore it, but when the logo apple appears, it simply shut down.

    my 5th ten iPod is basically doing nothing but trying over and over again to start up. I've tried to restore it, but when the logo apple appears, it simply shut down. Then I've connected it to my macbook pro, and I've seen the script "Please Wait - Very Low Battery", but, after some time, the iPod tries to start up again, and nothing happens. It's a kind of noise, I'm thinking about the hard disk, (it's a 80Gb version), and I'm listening to it; every 30 seconds seems to try to open and then shut down again. I can't see the iPod in iTunes too. Don't know what to do. Can someone help me? Thanks a lot, it's my first forum

    It sounds like the battery could be going bad as well as the iPod's Hard drive.  You'll want to have the iPod serviced either by Apple or a third party repair company. Here is Apple's pricing:
    http://www.apple.com/support/ipod/service/prices/
    Google for "iPod repair" and you should get a ton of results to work with.
    B-rock

  • My iTunes will not stay shut down. It automatically restarts even without an iPod plugged in. How do I fix this??

    My iTunes, which is the latest version, will not stay shut down. No matter how many times I exit the software, it automatically starts back up. And NO, there are NO iPods plugged in. It's very annoying and is slowing down our desktop immensly. I've tried to find a setting to change it but I'm not a computer/iTunes expert. Can anyone help??

    try holding the home button and off button at the same time for about 10 seconds, it should restart

  • Some times my mac not getting shut down, some times my mac not getting shut down

    some times my mac not getting shut down, some times my mac not getting shut down
    it will show white scree for long time and will not shut down

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
    Step 1
    Select "system.log" from the file list. Enter "BOOT_TIME" (without the quotes) in the search box. Note the times of the log messages referring to boot times. Now clear the search box and scroll back in the log to the time of the most recent boot when you had the problem. Post the messages logged during the time when you had the problem – the text, please, not a screenshot. For example, if the problem is a slow startup taking three minutes, post the messages timestamped within three minutes after the boot time. If the problem is a crash or a shutdown hang, post the messages from before the boot time, when the system was about to crash or was failing to shut down.
    Edit out excessive repeats and personal information, if any.
    If the log doesn't go back far enough in time, scroll down in the Console file list to /private/var/log/system.log.0.bz2. Search the archived log, and if necessary the older ones below them, for the same information.
    Step 2
    Do the same with kernel.log.
    Step 3
    Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the most recent one, if any. For privacy’s sake, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please do not post shutdownStall or hang logs – they're very long and not helpful.

  • Mac os x version 10.5.8 - safari version 5.0.6  safari will shut down sometimes

    mac os x version 10.5.8 - safari version 5.0.6  safari will shut down sometimes, a small window pops up, it reads your adobe flash player 10.4/10.5 may be the problem. i've been to adobe for help & got nowhere, any help on this matter would be great, thank-you.

    Hi..
    Try uninstalling the current Flash plugin then reinstalling new.
    Troubleshoot Flash Player | Mac OS
    Then quit and relaunch Safari

  • MacBook Pro (OS X 10.9.1) calendar continues to "connect to server" and will not allow shut down or restart. Force quit worked. How can I make this calendar "behave"?

    MacBook Pro (OS X 10.9.1) calendar continues to "connect to server" and will not allow shut down or restart. Force quit worked. How can I make this calendar usable? The problem began after I updated to Maverick.

    babowa, it seems like it is using Fuse & NTFS, so I don't think it's the classic WD + 10.9 mess, but extra WD tools & drivers can still break things MtTran.
    MrTran, if you must use unsupported disk formats on your Mac you must also consider actually paying the developers that made the trial software.
    It's probably a good idea to follow the developers removal instructions, reboot & then install one tool at a time.
    MacFuse, FuseOSX, NTFS-3G are all likley to confict if you run older versions so you need to be sure you are using the latest version. I can't remeber which one depends on the other, so you will need to read the manuals.
    When the disk is readable copy the data to another disk. You could probably do this from a Linux distro or Windows if OS X won't do it.
    If you insist on only using the trial versions you will need to reinstall Mac OS, copy data off this disk & reformat it.
    Is there any good reason for not using the Mac HFS extended format?

  • Safari does not allow shut down why.??

    safari does not allow shut down why.? I get a tab that says to quite  safari and i do, but it still does not allow it to shut down why.?

    You can force quit safari if you really want to shut it down.. if the problem remains , try deleting safar and downloading it again

  • Why does notes keep shutting down when I scroll up or down and when I try to add a note?

    Notes keeps shutting down when I try to scroll up or down the list an even if I try to add a new note.

    Please refer to the followibng link for the possible solution.
    http://helpx.adobe.com/creative-cloud/kb/ame-premiere-crash-launch-export.html

  • When I was editing a picture that I reposted on instagram, I hit the edit button and then a white screen appears and randomly shuts down. I have also noticed that my iPod has been crashing about every single 30 minutes!

    When I was editing a picture that I reposted on instagram, I hit the edit button and then a white screen appears and randomly shuts down. I have also noticed that my iPod has been crashing about every single 30 minutes! Please help!

    The iPod crashing when editing a photo is a known bug in iOS 5.1.1.
    For the other problem.
    Try the following:
    - A reset. Nothing is lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory settings/new iPod.
    If you still have the problem that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order

  • To shut down, or not to shut down?

    I read somewhere that it is better not to shut down your MBP at night because it is programmed to do maintenance from 3AM-5AM. Is this true?

    lissermarie,
    There are also other benefits to not shutting down. Being able to build and keep a larger cache of "Inactive" RAM is one of them, leading to much faster application launch times in many cases.
    More importantly, perhaps, is that there is no compelling reason to shut down, over simply putting your computer to sleep. We have had several portable Macs, and none of them have ever actually been shut down (just restarted, mostly when running updates, etc.). In one case that I know of, we had an iBook that had an "uptime" of over 160 days. That's almost 6 months with no shutdown or restart!!!!
    Scott

Maybe you are looking for

  • Condition records for RFQ outputs

    Hi I have seperate output types for RFQ (ZPRS) and PO (ZROP). I have created document types for PO and RFQ but both are having same code. Z007 - Hiring  Services PO (Category -F).. Z007 - Materials Req RFQ (Categ -A) Now when i am maintaining conditi

  • Select area through Drawing API

    Hi, I am working on Custom Kitchen Project and want to know if some one take a picture and import into the flash project then I just want to know how user can create or draw a random shape to select certain area, by using Drawing API Example is below

  • Passing data to IP address and PORT???

    Hi, I am trying to do a scenario, where in I need to make a synchronous call to a IP address and Port. The scenarion is SAP--> XI --> IP address/Port. Has anyone done this scenario, wherin you pass the string of data to a IP address and port? Regards

  • Configuration of bank accounts

    Hello, I was trying to do configuration for house banks and i came accross a field called account modification while assigning accounts to account symbol.  why is this field used for? and what is the purpose of this field. Thanks

  • FRM-40010 cannot read form

    I am using Oracle Forms Builder 10g and I have created a menu, but I have a problem in calling the form from this menu. The error is FRM-40010 cannot read form. I have changed the Forms_path in default.env and I put path of my folder which contains f