Laptop connection using existing e90 WLAN connecti...

Hey, maybe anybody can help. I'm in a hotel right now and my laptop does not provide WLAN. I'm able to setup a connection with my e90 and it works well in the internet. I installed a bluetooth connection to the laptop. What do I need to do to use the WLAN connection of the e90 via bluetooth with the laptop? I tried it with PCSUITE but it always try to start a dial up connection via GPRS.
Thx Torsten

Try if setting it to factory will bring it back to the state where it could connect & surf the net after reconfiguring again your access point.
Message Edited by android on 23-Nov-2008 12:22 PM
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

Similar Messages

Gprs used instead of Wlan connection

Hi,
when I start nokia maps on my N95 8GB, it uses the gprs connection instead of the wlan connection.
The wlan works fine, because if I remove my sim then it works ok (via wlan).
When I put back my sim card and start nokia maps again then the data is downloaded through gprs.
Is there a way in nokia maps, or anywhere else in the phone, where I can be warned if a gprs connection is opened?

Hi,
Thank you for your posting in Windows Server Forum.
As per your comment, I can say that if you want to deploy RDS server 2012 HA then you need to deploy DNS RR for your environment. It depends on the company requirement whether which one you need to use. It’s not compulsory that you need to use DNS RR, but if
you will access with DNS RR you don’t need to setup any Hardware LB. You can also use Hardware LB to load balance different RDSH server.
Please refer below articles for more information:
1. Remote Desktop Server farms explained (Part 1)
2. Remote Desktop Services 2012 | Remote desktop Connection broker High availability 2012
3. RD Connection Broker High Availability in Windows Server 2012
Hope it helps to understand!
Thanks,
Dharmesh

I have two airport extremes, one acting as amodem and the other operating in bridge mode. The extremes are connected using ethernet, but remain connected even when I disconnect the Cat5a cable. How do I know if they are operating wired or wirelessly

I have two airport extremes, one acting as a modem and the other operating in bridge mode. The extremes are connected using ethernet, but remain connected even when I disconnect the Cat5a cable (I did this to check that the 100 feet of Cat 5a cable connecting them was working). How do I find out if they are operating wired or wirelessly? I want to know as I assume I will get much better speeds if they are wired.

Hi Bob, many thanks for the prompt response. I think I did what you suggested, but you're the expert so I have sent over a few screenshots. The extreme in question is High Birches Home Office (the rest of the network has been in place and working well for some time). My new home office is going to be in the garden, circa 100 feet from the main house. I have installed armoured Cat5e cable down to the shed that is going to be adjacent to the home office once built and situated the High Birches Home Office Airport Extreme there temporarily. Everything works well, so I was surprised when I unplugged the ethernet, that it still worked. I also tested the ethernet cable by switching off my laptop's wifi and unplugging the cable from the airport extreme and directly into the laptop and that worked ok.
If the screenshots below (I did every Airport utility tab for the High Birches Home Office) don't tell you anything more, then the set-by-step instructions would greatly appreciated so I can ensure I completed the steps correctly.
Many
Thanks, Greg.

Camera connect kit disturbs/cuts wlan connection when plugged in... why?

My camera connect kit disturbs/cuts wlan connection when plugged in to my iPad 2 ... why? It is impossible to keep wlan-connection while using the camera connect kit... does anybody have similar experiences?

... It was not really the cam connection kit... It was infact the radio dongle plugged in to the connection kit what created problems... The signal of the dongle was disturbing the WLAN antenna of the iPad... I was looking for a possibility to have a external soundbox connected without cable and for listening to live streamed news... Now, I need the cable for connecting the dongle with distance to the iPad... Not really a satisfying solution... Nö way arround, I guess?!?

Can I use existing portal to connect to multiple R3 systems for config

I am planning to use existing portal 6.0 to connect to multiple R/3 systems for testing and configuration.
We have three portals in our landscape DEV TST and PRD.
Our R/3 system landscape -->DEV, DEV2, TST,TST2,TST3 etc.
DEV portal is connect to dev system TST portal to R/3 TST system etc.
Is there a way I can connect DEV portal to DEV2 R/3 System without effecting portal testing and configuration which is in progresses in DEV R/3 system.
If any one has done it in the past, please share instructions
Thanks,
adil

Hi Syed,
Check this link for creating systems.
Configuring EP for connecting to SAP R/3
http://help.sap.com/bp_epv260/EP_EN/documentation/EP/N03_BB_InstallGuide_EN_US.doc
Regards
Arun

Time capsule connect to existing network cannot connect MBP via ethernet

I have set up my time capsule via Airport utility to "connect to existing network", which is my Netcomm wireless router (which is my DHCP server). MBP connects perfectly to time capsule if wireless is on, presumably via the Netcomm. But if I plug the MBP into an ethernet port on the time capsule it is not recognized and it gets a self assigned ip 169.254.x.y.
Airport utility is very restrictive in the options and is basically useless in resolving the obvious ip conflict. Is there any trick to getting both the wireless and ethernet to work ? It should not be this difficult....
The time capsule 2T disk is useless as a backup device over wireless.

[email protected] wrote:
I have set up my time capsule via Airport utility to "connect to existing network"
Is that the exact wording of the option you chose? In AirPort Utility I see options of "Create a wireless network", "Join a wireless network", and "Extend a wireless network". (Perhaps the difference is due to language usage.) The option to "Join a Wireless Network" is only useful for sharing disks and printers. It doesn't support Ethernet ports.
if I plug the MBP into an ethernet port on the time capsule it is not recognized
With some options there's a checkbox to "Allow Ethernet Clients". If you see that, try it.

Can't connect using ethernet but can connect using Airport

The problem I am currently facing is when I try to plug an ethernet cable into my MacBook Pro I can't get on the internet. At home I use an AEBS and connect fien, but when I go over to a friends house and they don't have wireless I try to hook up using the ethernet cable directly from the modem to connect and I can't.
I open System Pref and it says on the left side under ethernet "Self Assigned IP" On the right hand side it says ethernet is connected and underneath that it says, "ethernet has self assigned IP address and may not be able to connect."
I though this was a problem at his house and when I went home I tried it and I get the same thing. I used to have a Powerbook using Tiger and it did the same thing. Once I turn my Aiprort back on and plug the ethernet cable back into my AEBS I get on line.
Am I doing something wrong? I figured if I just plug in an ethernet cable it should detect it and work.
Thanks

I am not sure if this is your problem, but I believe a lot of cable modems need to be power cycled if you switch the device that is connected to them. They only recognize the MAC address of the first device that connects to them after they have been power cycled.
Although this was a couple of years ago, I was trying to investigate something (I can't remember what now) and I unplugged my router from my cable modem and plugged one of my computers directly to it. I found I couldn't do anything on the Internet. Later, when I was looking at the Comcast forums, I found the information about needing to power cycle the modem to get it to accept the "new" device.

BB Torch - bluetooth tethering for laptop internet use: "Error 720: A connection to the remote computer could not be established

Trying to set up Blackberry Torch for laptop tethering...bluetooth. I have connection/drivers/etc. but keep getting error message: "Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection." Where and what do I chancge setting to so this will work?
I have synched my phone and laptop wirelessly across other internet connection....just cant get this above to work. Anybody know how to fix this? Thanks!

Hi,
Since it worked previously, a quick solution is to run System Restore and get back to the previous status when the issue didn’t occur.
If system restore doesn’t help, please also try the following:
1. Check if you can establish the VPN via other connections except the connection through the UMTS card.
2. Reset the PPTP and L2TP WAN miniport with running the following commands one by one in an elevated command prompt:
Netcfg -u MS_L2TP
Netcfg -u MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_L2TP
Then reboot the computer and see how it works.
Meanwhile, I would like to share the following with you for your reference:
Troubleshooting common VPN related errors
Hope this helps. Thanks.
Nicholas Li - MSFT

HT1600 at the end of a recent apple tv update, a picture appeared suggesting a connection using a micro usb connection to i believe Itunes. the apple tv did not come with a micro usb connection. What to do.

At the end of a recent apple tv update, a picture appeared showing a connection - micro usb - to apple itunes. I don't have this micro connection. I now can't watch apple tv. what is going on?

Many newer cameras have the Micro USB cable you can use.
Otherwise, you will need to buy one to restore your Apple TV.

Setup Email Using WLAN Connection - E72

Hi.
Did anyone manage to setup a Gmail or Windows Live Email using WLAN connection?
1 - My internet connection has only the WLan connection. I removed my carrier internet connection.
2 - Using the E-mail option at the menu, I type my gmail user, my password, and then nothing happens.
3 - I tried doing this procedure without the SIM, using Offline mode. And again, nothing happens...
Does Nokia want me to use my Carrier Connection just setup an email account using their interface and software?

Yes for initial setup must use GPRS/3G from your provider. After the inital setup, it may or may not work with WiFi depending on your location.
Was this post helpful? If so, please click on the white "Kudos!" star to the left. Thank you!

Asha 302 wifi problem - "WLAN connection failed"

I have nokia asha 302 two days. I have problem with wifi connection. I see "my wifi" in wifi list, but when I click connect, I get message "WLAN connection failed". Version of mobile Asha is 14.78.
I have router Ovislink WN-200R. My wifi setinngs is in attachment (set 1).
I tried to change password, change security system, set to without security system, ... - without changing. At last I found bug and one solution. When I set wifi, how is in attachment (set 2), is to possible to connect with Asha 302.
But in my house I use PC with wifi N for speed. Do you know any other solution?
PS. I use Nokia 5530, Iphone 4GS, HTC desire S too. And I don`t have this problem.
Thanks a lot
Attachments:
Asha_302_wifi_problem.png ‏98 KB

DennIz wrote:
"Wrong Password"
There are several reasons why that could happen. One reason: Your network changed from WPA2-PSK back to WPA1-PSK. Some Wi-Fi access-points have silly mixed-mode settings. If your network is in mixed mode, first try the old version: WPA-only (WPA-PSK). Because some very old Wi-Fi access-points do not support WPA2 correctly even for multicast, as next step try the more secure version 2: WPA2-PSK. If that does not work:
Do you have a Mac OS X computer around?
If yes, please, go to Applications » Utilities » Terminal and enter
/System/Library/PrivateFrameworks/Apple80211.framework/Resources/airport -I -s
The last part (Security) should be ‘WPA2(PSK/AES/AES)’ and nothing else.
Do you have a Windows Vista, Windows 7, or Windows 8 computer around?
If yes, please, open a command prompt (as Administrator, keys: Windows-R), and enter
netsh wlan show networks mode=bssid
The network type has to be not Ad-hoc but Infrastructure.
The basic rates should be ‘1 2 5.5 6 11 12 24’ (IEEE 802.11g/n) and nothing else.
Do you have a Android device around?
If yes, install the free Wifi Analyzer. Within that tool, please, tap the wrench icon (Settings) » Show full securities. Then go back and have a look at your Wi-Fi.
It must be [WPA2-PSK-CCMP][ESS] and nothing else.
If the connection still fails, please go to the configuration interface of your Wi-Fi access point and change your access-point back to the old WPA-PSK (TKIP-only) and 802.11g (only). If not available, avoid 802.11n and go for 802.11b/g. Does it work now?
If it still does not work, change your settings back to WPA2-PSK (AES-CCMP) only and 802.11g/n. Then, post the results of the above tools. If you do not like to post them into the public, you can send me a private message. But those information are public to your neighbours anyway.

Nokia C3 WLAN Connection Failed..

I recently bought a Nokia C3.I have a Wifi at home..(WEP)450TC1-ADSL Router .I use a Vodafone connection.Whenever i try to use WLAN on my cell it detects this Wifi and asks for password.On entering this password it tries to Connect but soon shows WLAN Connection Failed.My WiFi is functional and has no problems.Please help me sort this problem.Thank You.

Hi,
You are right, its working with additional changes.
In Menu - Settings - Configuration - Default config. settings.
You can try this, it may work.
If you go to Menu - Settings - Configuration - Personal Settings - My Web
And follow the steps, you do not need to fill in any details, just activate it.
Then go to Menu - Internet - Web Settings - Configuration Settings, then select configuration and change to Personal configuaration. Then the 'account' should say my web.
So for good, then check the
Menu - Settings - Configuration - Default config. settings. "Default config. settings", if that still in operator's config settings you have to change this in to "Personal Config."
then it will work properly

E61i is keeping WLAN connection after VoIP call

I've just upgraded from E61 to E61i, upgraded phone firmware to 2.06 and... I'm very disappointed about some "improvement" in the Internet telephone. My SIP profile is the same as it was in E61, registration mode "When needed". The phone would register to SIP service and make calls okay. However, if a call wasn't answered and I terminate it with the "End" key, I can't drop WLAN connection. I would go to Internet telephone and disconnect from the service, SIP telephone icon would disapper but WLAN icon would be still showing. There is no way to get rid of WLAN connection, even if I'd drop it manually in connection manager it would re-appear in a second or so. The only way to disconnect is by switching phone off/on.
What's amazing, if a call was answered, everything would be working as it should: once I disconnect from the service in the Internet telephone, both SIP and WLAN icons would disappear.
Any ideas?

I think it's a bug, too! I don't know how to repeat the upgrade process (the Nokia Upgrade says my firmware is up-to-date) but anyway, the upgrade process terminated normally... I don't think the problem is there.
Note that the problem only occurs when I terminate VoIP call with the "End" key. If the call was answered and terminated by remote hangup, everything's fine.
I never had such a problem with E61. In fact, I never had to use the "Internet telephone" application on E61. When I wanted to disconnect from SIP proxy, I just went to Connection Manager and terminated WLAN connection there.

E71 Firmware Upgrade to 110.07.127 + WLAN Connecti...

I have a E71 (RM 346) (15 Days Old - Just Purchased it)and I have updated my firmware to Version 110.07.127 last night.
I have following problesm:
1. Even When I am standing next to the Wifi Access Point the E71 will say that there is no WLAN Available. (However while doing the SCAN, my laptop which uses the same WLAN Network works, fine.
2. After the upgrade of the firmware - I am unable to use the GPRS/EDGE from my operation - as I have unlimited data plan.
I HAVE DONE A COMPLETE FACTORY Reset as well - but nothing helps. This problem was NOT there before the Firmware Upgrade.
Any Help will be greatly appreciated.
Thanks -

30-Dec-2008 03:35 PM
cynnabon wrote:
yeah, it didn't work..
any solution there please tell me
i'm kinda tired of my nokia e71
I believe the only solution would be to downgrade to the previous firmware and wait till new one will come.
Strange, no replies from Nokia people at all. Looks like they don't care about this forum...
Can anybody comment is that confirmed problem and does Nokia work on it or not?

Is my IP address visible if using another wireless network connection?

i've got a few questions concerning surfing anonymously on the web...
first off, are there any MAC apps that would allow me to surf, proxy surf, anonymously? i know there are many available for the PC.
second, is my IP address visible to others on the web if I am connected using someone elses wireless connection instead of mine?
thanks for any insight you may be able to offer.
-roadk

i've got a few questions concerning surfing
anonymously on the web...
first off, are there any MAC apps that would allow me
to surf, proxy surf, anonymously? i know there are
many available for the PC.
Sure:
http://www.google.com/search?q=osx+anonymousproxy
second, is my IP address visible to others on the web
if I am connected using someone elses wireless
connection instead of mine?
I'm not sure you understand the concept of 'your IP address.'
If you use someone elses wireless connection, almost certainly you will get a ssigned a private (rfc 1918) IP address by their router, and that wireless router will be providing the internet via NAT (network address transalation). IOW, you make a web request, the router changes your private IP address into its public one, waits for the reponse, then sends it back to your private address....So, in that scenario...what do you consider 'your' IP address ?
The wireless routers IP address will be known, yes. Anyone with access to the logs on that wireless router will see your MAC address, and see that you have been assigned an IP address, and have accessed the router ( assumeing they know how to read thier logs.) But no one on the internet should be able to tell that your computer made a particular request from behind that wireless router...there is nothing identifying you in that request that goes out into the internet.
So, perhpas I have the scenario wrong, but if not, I hope that answers your concerns.

Laptop connection using existing e90 WLAN connecti...

Similar Messages

Maybe you are looking for