Laptop did not sleep properly and did not like being stuffed in the laptop bag

This morning I closed the lid on my laptop, saw that the sleep icon on the hinge came on, put the laptop in my bag, put it in the trunk of the car and went to work. Twenty minutes later I get to work and grab my bag. The bag was extremely hot! And when I flipped it open and touched the end of the laptop, it was even hotter. To the point where it did not feel good to touch.
The exhaust fan end was at the top end of the bag and is the end that I was touching. The fan was going full speed.
I brought it into the office, opened it and there was a DOS screen that listed all of the available boot devices and pretty much said nothing was available. I hit enter and it cycled through a couple DOS screens but basically it didn't want to do anything. So, did a hard shut down and let it cool down to where it was comfortable to the touch. Powered back on and was able to get into Windows fine. The battery was fully charged when I left the house but was down to 40%. By the time I got PC Wizard up, the internal temps had fallen back to normal.
Got my W500 about a week ago. Wiped Vista Ultimate and replaced with Windows 7. For the most part, everything I need to work is working fine. Still have a few devices that probably aren't completely configured properly. I did this whole routine yesterday for the first time (to and from work) without any issues so I am a little confused what happened this time.
Any thoughts? Anything I should look for? Specific drivers I need to update? I see a couple of threads around sleeping issues but haven't confirmed anything on my end. What steps should I take to make sure that the thing really did go to sleep before stuffing it in my bag again? 
So far it seems OK but I can only imagine what might have happened if I had the fan end at the bottom of the bag, it was in the afternoon and 100 degrees and if my drive were a little longer. I think it would have been messy.
Thanks,
Matt
Solved!
Go to Solution.

This was actually the problem but I just figured it out today (without seeing the RealStranger post).
The problem has not happened again since the first time, but I've been pretty vigilant about making sure it is actually asleep. However, this morning as I was packing up to go to work, I had just put it to sleep and was in the process of turning off my cordless USB mouse (Logitech VX Nano FTW), when I heard the computer beep and saw that it had come out of sleep mode. I played with it a couple of times and sure enough, turning the mouse on and off triggers it to wake up.
I haven't actually changed any settings yet (since I just saw this post) but I will shortly.
Thanks! I can quit worrying about it now.

Similar Messages

  • Hi I have just aquired a Mac Pro 2006, Dual Xeon 266, 3Gb RAM 360GB HD, I have tried to add another 2TB HD but for some reason it is not identified properly and will not erase

    I have spoken to Apple tech, who suggested upgrading to Snow Leopard, but reading through the tech specs I believe my Mac Pro can support Lion OS, any thoughts on this matter?  I also added a 2Tb HD, which 10.4.1 the current OS on the machine, does not recognize properly.  Will Snow Leopard solve this problem? Or will I have to remove the 360Gb HD and Format/erase the 2T disk and set it up as the new Boot disk?  JackTar1957

    You have a good memory for this, the hatter:
    #Mac Pro
    Date introduced
    Original Mac OS X included
    (see Tips 1 and 3)
    Later Mac OS X included
    (see Tip 1)
    Mac OS X Build(s)
    (see Tip 2)
    Mac Pro (Late 2013)
    Dec 2013
    10.9
    10.9.2
    13A4023, 13C64
    Mac Pro (Mid 2012)
    Jun 2012
    10.7.3
    10.8, 10.8.3
    11D2001, 12A269, 12D78
    Mac Pro (Mid 2010)
    Aug 2010
    10.6.4
    10.7, 10.7.2, 10.7.3
    10F2521, 10F2554, 11A511a, 11C74, 11D2001
    Mac Pro with Mac OS X Server (Mid 2010)
    Aug 2010
    10.6.4
    10.7, 10.7.2, 10.7.3 (Server)
    10F2522, 11A511a, 11C74, 11D2001 (Server)
    Mac Pro (Early 2009)
    Mar 2009
    10.5.6
    10.6
    9G3553, 10A432
    Mac Pro (Early 2008)
    Jan 2008
    10.5.1
    10.5.2, 10.5.4
    9B2117, 9C2031, 9E25
    Mac Pro
    Aug 2006
    10.4.7
    10.4.8, 10.4.9, 10.4.10, 10.5
    8K1079, 8N1430, 8N1250, 8K1124, 8P4037, 8R3032, 8R3041, 9A581, 9A3129
    Mac OS X versions (builds) for computers

  • Zen Sleek not charging properly and battery not holding cha

    Hi everyone. My Sleek has the latest firmware and is about 4 months old. I've searched for any info regarding my specific problem but can't find any. The problem is that the player won't charge. I plug in the charger and the charging sign shows. This quickly - in less than a minute I think - changes to the plug sign, suggesting?that the player is fully charged. I turn off the charger and the battery strength goes down to 0 or bar immediately and if I try playing it, it very quickly gives up and either switches itself off or, more often, freezes. When I plug the charger back in, the player usually has to rebuild the library before I can play anything. I've tried leaving the player switched on with idle shutdown turned off. When I do this, the fully charged sign disappears after a bit and the battery looks like it's charging for a short period of time before the charged sign comes back, but the result is the same. I've even tried doing?this overnight but with no joy. As I type, I'm trying to charge the player via a USB port. It looks like it's charging for about 30 secs, then the charged sign comes up, then it goes away and I'm left with 2 bars. Unplugging the player leaves me with no bars again. Also, the number of bars has in the past seemed to change randomly - 0 bars, then 2 bars, then bar etc. And it's gone from 2 bars to 'Low battery' and switching itself off without any inbetween stage. I've done a disk clean quite a few times with no joy. I had the same problem a few months ago and I tried all the above things and then it just seemed to randomly sort itself. So I stuck. Any suggestions would be gratefully received!?Thanks, Martin.

    Did you try just leaving the player plugged in the to charger regardless of what the charging sign indicated?The problem you describe is a quite common characteristic of lithium batteries when they have done a few hundred charging cycles and are left to run very low or empty on charge. There is some quite convincing evidence that unlike using ni-cad or ni-mh batteries, we should not fully empty lithium batteries and that regular top-up charges are better for them. The player's charging circuit basically cycles between charging and testing the battery's output voltage. So after the 30 seconds to minute you describe the player stops accepting charge and tests the voltage from the battery. When lithium batteries have been charged for a short time from empty, the voltage they show to the test is almost what the charging voltage was, so it stops charging believing the battery to be full. Some charging circuits give up then, especially those that can't trickle charge (applying a small current to keep the battery topped up but not charging) to protect the battery. So basically you did the right thing to revi've the battery, but maybe for the next few cycles, just leave it til it gets to 30-50% before recharging. Hope that helps in some way

  • RAM Not working properly and files not deletes (2 in 1)

    Hello. Ive installed 6Gb of ram on my iMac, and system shows all 6. But in-use only 2. When im restarting computer, its works normaly, but when trying to open any default app - 4gb disappears =( U can see this on screenshot here: http://photo.vibos.org/#287 ... How can i fix this? And why its happening?
    And second problem:
    ive deleted some files from external hdd to trash and now cant empty her =(
    when im clicking on "empty" or "safe empty" my CPU and RAM uses for 100% and then computer freezes. cant understand how delete this files from trash =(
    hdd is SATA, 1Tb and used before in windows, so its has ntfs file system. om my mac im using paragon ntfs as active solution and mac fuse as secondary, not active rigth now.
    Thx 4 help and sry f
    P.S.: om my mac book i cant install photoshop because i have extended fs with registry (or some like that). how can i change fs type or install ps on other partition of hdd?

    The machine has a 1 year warranty, book an appointment with your local Apple Store or AASP to have it looked at.
    You can try doing a SMC reset however I don't think that is the solution.
    SMC RESET
    • Shut down the computer.
    • Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    • On the built-in keyboard, press the (left side) Shift-Control-• Option keys and the power button at the same time.
    • Release all the keys and the power button at the same time.
    • Press the power button to turn on the computer.
    PRAM RESET
    • Shut down the computer.
    • Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    • Turn on the computer.
    • Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    • Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    • Release the keys.

  • HT1414 after a software update the device is not working properly and can not open any website.

    I can operate it properly after an software update . Now no website cannot be opened and cannot get emails. Main thing cannot go to tunes and app store .

    First Try This...
    Close All Open Apps... Sign Out of your Account... Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...
    If no joy... Try a Restore...
    1: Connect the device to Your computer and open iTunes.
    2: If the device appears in iTunes, select and click Restore on the Summary pane.
    Restoring  >  http://support.apple.com/kb/HT1414

  • Ever since updating my LG G2 to VS98026A the Quiet mode does not work properly and is not controllable.

    My LG G2 started to have problems since the latest system update.  Previously, the phone worked perfectly! 
    I now cannot control the Quiet mode settings and the vibrate and silent modes are no longer selectable.  This is not acceptable.  I have no way of silencing the phone if I need to.
    Is there a way to return the phone to the previous state?

    http://www.verizonwireless.com/support/knowledge-base-87344/
    No can't go back but if you reset you g2 make sure you use cloud storage ahead of time on WiFi to backup data or connect to a computer and know your Google account. If on more everything plan you can use the free 25gb of vcloud storage

  • I tried to migrate my files from my old G4 book to my new Macbook Air. It did not work properly and I want to restore the Air to its original settings. How do I do this?

    I tried to migrate my files from my old G4 book to my new Macbook Air. It did not work properly and I want to restore the Air to its original settings. How do I do this?

    You will need to use an external DVD drive to run the disc installer that came you your machine. You can also do it with another Mac using the Remote Install Max OS X app. Finely, if you have access to another computer, you could burn the install image on a USB thumb drive, boot from that, erase the drive and run the installer.  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

  • Song did not install properly and now won't play

    I pre-ordered an album, and when it came round to installing it, I was in an area with a weak internet connection. At one point during installation, the internet signal temporarily cut out, causing the song to not install properly. I have a few seconds at the beginning of the song that has the audio in it, but after that the song stops and does not play any more. I need to know if there is a way to reinstall the song, or redeem it some other way. I have tried to create an AAC version of the song, but an 'unknown error (-3)' message appears. Is there any way I could reinstall that one song?

    Depending upon what country that you are in (music can't be re-downloaded in all countries) then try deleting the track from your iTunes library and redownload it via the Purchased link under Quicklinks on the right-hand side of the iTunes store home page on your computer's iTunes.
    If you aren't in a country where you can re-download music (or if it re-downloads with the same problem) then try the 'report a problem' page to contact iTunes Support : http://reportaproblem.apple.com
    If the 'report a problem' link doesn't work then you can try contacting iTunes support via this page : http://www.apple.com/support/itunes/contact/- click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

  • I download the new IOS7 in my iPad beeing in the usa And where I come back to my country appears me again to upad te my iPad of ferina the IOS 7. I did it my iPhone And is not working as before.what i must do

    I download the new IOS7 in my iPad beeing in the usa And where I come back to my country appears me again to upad te my iPad of ferina the IOS 7. I did it my iPhone And is not working as before.what i must do

    I'm sorry, but I do not understand what you are asking or saying. Perhaps you could clarify a little bit.

  • What should i do my sleep/wake button on iphone 5 does not work properly it only works if i press on the left side of it and my iphone still on warranty i heard its a common problem

    what should i do my sleep/wake button on iphone 5 does not work properly it only works if i press on the left side of it and my iphone still on warranty i heard its a common problem

    If there's a hardware defect and your phone is under warranty, bring it to Apple for replacement.

  • MacBook Pro NOT sleeping properly anymore, and getting hot.

    My MacBook Pro does not sleep properly anymore, and gets really really hot, anytime I send it to sleep either by closing it or by selecting "sleep" from the menu. It also loses all its battery really fast while on this state (even faster than while being awake and being heavily used).
    It started a while ago only, or at least it was not there from the begining. I had never before had to put off a MacBook Pro, except while flying... I always just close them and they sleep after a few seconds; BUT I can not do like that anymore with my new MacBook Pro... I have to save, close and shut down... then turn on, open my apps, and open my files... its not something to be happy of... I'm very sad with this problem and I have been unable to find the reason for the sudden change.
    Please I need help with this.

    An additional detail I forgot to mention:
    Everytime I tell my MBP to sleep, or just close it, the computer does not seem to go off (because of the levels of the sound of the HD and of the fan), though the screen goes off correctly.
    Now, the strange part is that everytime I "wake it", the screen goes on immediately, asking for my password, and after inputing it correctly the screen goes COMPLETELY OFF for 2 seconds, before "coming back normally".

  • My G5 is not booting up and it sounds like an airplane taking off.  I replaced the 3.6v battery, but did not correct the problem.  Any suggestions?

    My G5 is not booting up and it sounds like an airplane taking off.  I replaced the 3.6V battery, but it did not correct the problem.  Any suggestions??

    Resetting the Logic Board
    Resetting the logic board can resolve many system problems. Whenever you have a
    unit that fails to power up, you should follow this procedure
    before replacing any modules.
    1 Unplug the computer.
    2 Press the Power On button on the front of the unit.
    3 Open the side access panel.
    4 Remove the battery from the logic board.
    5 Wait at least 10 minutes before replacing the battery.
    6 Make sure the battery is installed in the correct +/-
    direction.
    7 Reassemble the computer and test the unit.
     Cheers, Tom

  • 2011 MBP not sleeping properly when power runs out

    My macbook is behaving strangely. Every time the battery runs out, it doesn't sleep properly and restarts by itself when the power supply is attached.
    The clock and date reset to 2001 but it is not a problem with the clock battery, this has been working fine up until the last few days.
    The reason i say it is not the clock battery is because the actual power behaviour is behaving strangely. For example, the last time the battery ran out, the power indicator said there was still 3%/ten minutes left. The computer is cutting power before the sleep mode kicks in. Also, sometimes after the power cuts, when restarting the battery monitor shows 10 or 11 hours to recharge. The normal recharge time would be around 2.5 - 3 hours.
    Also, just after a power cut with no sleep, when i am reconfiguring the lost settings, the processor maxes and stays that way, even when the computer is doing nothing.
    I have tried resetting the PRAM and also an SMC reset but they are making no difference.
    Anyone have any ideas? I already suspect this computer has malware on it but i think this particular problem is something else again...

    I have to admit, I was not holding my breath. I have experienced this condition with on my own MBP twice this year. Once while running Leopard and once while running Snow Leopard. Both times it was only resolved after reinstalling the OS again.
    I can't remember, though, if simply reinstalling the OS over the existing installation was sufficient or if I had to wipe the drive, reinstall the OS, and migrate my data back over. I assume you have a backup going.
    The easiest thing to try first is insert the SL DVD and perform an installation. The default now is a variation of Archive & Install, where the OS is replaced without touching your user data. You don't need to make any special selections, just let the installer go.
    In the event that does not work, and AFTER you have verified you have a current backup of everything, then insert the DVD and click the Options button, then click Restart in the window. This will reboot the Mac off of the DVD. At the Welcome splash screen go up to the Utilities menu and select Disk Utility. Then reformat your Macs' internal HD. Then proceed with the installation. Near the end you will be asked if you want to migrate user data over. Select the method of migration you wish (Time Machine, clone, etc...) and move your user data back.
    Unfortunately, it is the only way I have resolved this issue if the earlier suggestions did not work. let us know what you decide to do. Cheers!

  • MBP not sleeping properly, waking up every 2 hours

    For a while now my MBP does not sleep properly. For example, last night I put it manually to sleep. Looking in the log I see it woke up every two hours.
    I moved the Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist to the trash. No luck.
    I did reset the PRAM and System Management Controller (SMC). No luck.
    Anybody know what causes this and how to fix?
    Thanks
    log file from this AM:
    16/05/2010 01:09:35 kernel hibernatepage_listsetall start
    16/05/2010 01:09:35 kernel hibernatepage_listsetall time: 242 ms
    16/05/2010 01:09:35 kernel pages 519043, wire 52766, act 187684, inact 91326, spec 3, zf 590, throt 0, could discard act 122317 inact 51265 purgeable 8976 spec 4116
    16/05/2010 01:09:35 kernel hibernatepage_listsetall found pageCount 332369
    16/05/2010 01:09:35 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 01:09:35 kernel IOHibernatePollerOpen(0)
    16/05/2010 01:09:35 kernel writing 332137 pages
    16/05/2010 01:09:35 kernel image1Size 99302400
    16/05/2010 01:09:35 kernel PMStats: Hibernate write took 12173 ms
    16/05/2010 01:09:35 kernel all time: 12173 ms, comp time: 2480 ms, deco time: 0 ms,
    16/05/2010 01:09:35 kernel image 678409216, uncompressed 1360797696 (332226), compressed 675726752 (49%), sum1 c7de95a0, sum2 5f6f032b
    16/05/2010 01:09:35 kernel hibernatewriteimage done(0)
    16/05/2010 01:09:35 kernel sleep
    16/05/2010 01:09:35 kernel Wake reason = RTC
    16/05/2010 01:09:35 kernel RTC: maintenance alarm 2010/5/15 23:09:35, sleep 2010/5/15 21:09:53
    16/05/2010 01:09:35 kernel System Wake
    16/05/2010 01:09:35 kernel Previous Sleep Cause: 5
    16/05/2010 01:09:38 configd[13] network configuration changed.
    16/05/2010 01:09:51 kernel hibernate image path: /var/vm/sleepimage
    16/05/2010 01:09:51 kernel sizeof(IOHibernateImageHeader) == 512
    16/05/2010 01:09:51 kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xf0c805000, maxio 400000
    16/05/2010 01:09:51 kernel hibernate image major 14, minor 3, blocksize 512, pollers 5
    16/05/2010 01:09:51 kernel hibernateallocpages flags 00000000, gobbling 0 pages
    16/05/2010 01:09:51 kernel System SafeSleep
    16/05/2010 03:09:51 kernel hibernatepage_listsetall start
    16/05/2010 03:09:51 kernel hibernatepage_listsetall time: 241 ms
    16/05/2010 03:09:51 kernel pages 518995, wire 52306, act 186725, inact 91189, spec 2, zf 590, throt 0, could discard act 122313 inact 51320 purgeable 10219 spec 4331
    16/05/2010 03:09:51 kernel hibernatepage_listsetall found pageCount 330812
    16/05/2010 03:09:51 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 03:09:51 kernel IOHibernatePollerOpen(0)
    16/05/2010 03:09:51 kernel writing 330580 pages
    16/05/2010 03:09:51 kernel image1Size 98721792
    16/05/2010 03:09:51 kernel PMStats: Hibernate write took 12126 ms
    16/05/2010 03:09:51 kernel all time: 12126 ms, comp time: 2471 ms, deco time: 0 ms,
    16/05/2010 03:09:51 kernel image 677233152, uncompressed 1354420224 (330669), compressed 674559536 (49%), sum1 26bd31c7, sum2 92f72ed1
    16/05/2010 03:09:51 kernel hibernatewriteimage done(0)
    16/05/2010 03:09:51 kernel sleep
    16/05/2010 03:09:51 kernel Wake reason = RTC
    16/05/2010 03:09:51 kernel RTC: maintenance alarm 2010/5/16 01:09:51, sleep 2010/5/15 23:10:05
    16/05/2010 03:09:51 kernel System Wake
    16/05/2010 03:09:51 kernel Previous Sleep Cause: 5
    16/05/2010 03:10:07 kernel hibernate image path: /var/vm/sleepimage
    16/05/2010 03:10:07 kernel sizeof(IOHibernateImageHeader) == 512
    16/05/2010 03:10:07 kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xf0c805000, maxio 400000
    16/05/2010 03:10:07 kernel hibernate image major 14, minor 3, blocksize 512, pollers 5
    16/05/2010 03:10:07 kernel hibernateallocpages flags 00000000, gobbling 0 pages
    16/05/2010 03:10:07 kernel System SafeSleep
    16/05/2010 05:10:07 kernel hibernatepage_listsetall start
    16/05/2010 05:10:07 kernel hibernatepage_listsetall time: 241 ms
    16/05/2010 05:10:07 kernel pages 519856, wire 52672, act 186322, inact 91097, spec 3, zf 590, throt 0, could discard act 122331 inact 51323 purgeable 11187 spec 4331
    16/05/2010 05:10:07 kernel hibernatepage_listsetall found pageCount 330684
    16/05/2010 05:10:07 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 05:10:07 kernel IOHibernatePollerOpen(0)
    16/05/2010 05:10:07 kernel writing 330452 pages
    16/05/2010 05:10:07 kernel image1Size 99039744
    16/05/2010 05:10:07 kernel PMStats: Hibernate write took 12187 ms
    16/05/2010 05:10:07 kernel all time: 12187 ms, comp time: 2472 ms, deco time: 0 ms,
    16/05/2010 05:10:07 kernel image 677464576, uncompressed 1353895936 (330541), compressed 674788528 (49%), sum1 e647b291, sum2 3a8aac2b
    16/05/2010 05:10:07 kernel hibernatewriteimage done(0)
    16/05/2010 05:10:07 kernel sleep
    16/05/2010 05:10:07 kernel Wake reason = RTC
    16/05/2010 05:10:07 kernel RTC: maintenance alarm 2010/5/16 03:10:07, sleep 2010/5/16 01:10:21
    16/05/2010 05:10:07 kernel System Wake
    16/05/2010 05:10:07 kernel Previous Sleep Cause: 5
    16/05/2010 05:10:10 com.apple.launchd[1] (com.apple.newsyslog) Throttling respawn: Will start in 6 seconds
    16/05/2010 05:10:15 ntpd[19] sendto(17.72.255.11) (fd=26): Can't assign requested address
    16/05/2010 05:10:23 kernel hibernate image path: /var/vm/sleepimage
    16/05/2010 05:10:23 kernel sizeof(IOHibernateImageHeader) == 512
    16/05/2010 05:10:23 kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xf0c805000, maxio 400000
    16/05/2010 05:10:23 kernel hibernate image major 14, minor 3, blocksize 512, pollers 5
    16/05/2010 05:10:23 kernel hibernateallocpages flags 00000000, gobbling 0 pages
    16/05/2010 05:10:23 kernel System SafeSleep
    16/05/2010 05:10:23 kernel hibernatepage_listsetall start
    16/05/2010 05:10:23 kernel hibernatepage_listsetall time: 242 ms
    16/05/2010 05:10:23 kernel pages 520172, wire 52398, act 186343, inact 91074, spec 3, zf 590, throt 0, could discard act 122371 inact 51663 purgeable 11204 spec 4526
    16/05/2010 05:10:23 kernel hibernatepage_listsetall found pageCount 330408
    16/05/2010 05:10:23 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 05:10:23 kernel IOHibernatePollerOpen(0)
    16/05/2010 05:10:23 kernel writing 330176 pages
    16/05/2010 05:10:23 kernel image1Size 98969600
    16/05/2010 05:10:23 kernel PMStats: Hibernate write took 12185 ms
    16/05/2010 05:10:23 kernel all time: 12185 ms, comp time: 2471 ms, deco time: 0 ms,
    16/05/2010 05:10:23 kernel image 677498368, uncompressed 1352765440 (330265), compressed 674825472 (49%), sum1 83188ead, sum2 deb81330
    16/05/2010 05:10:23 kernel hibernatewriteimage done(0)
    16/05/2010 05:10:23 kernel sleep
    16/05/2010 07:10:23 kernel Wake reason = RTC
    16/05/2010 07:10:23 kernel RTC: maintenance alarm 2010/5/16 05:10:23, sleep 2010/5/16 03:10:37
    16/05/2010 07:10:23 kernel System Wake
    16/05/2010 07:10:23 kernel Previous Sleep Cause: 5
    16/05/2010 07:10:25 kernel Ethernet [AppleYukon2]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af08,0de1,0200,c5e1,2800]
    16/05/2010 07:10:27 configd[13] network configuration changed.
    16/05/2010 07:10:39 kernel hibernate image path: /var/vm/sleepimage
    16/05/2010 07:10:39 kernel sizeof(IOHibernateImageHeader) == 512
    16/05/2010 07:10:39 kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xf0c805000, maxio 400000
    16/05/2010 07:10:39 kernel hibernate image major 14, minor 3, blocksize 512, pollers 5
    16/05/2010 07:10:39 kernel hibernateallocpages flags 00000000, gobbling 0 pages
    16/05/2010 07:10:39 kernel System SafeSleep
    16/05/2010 07:10:39 kernel hibernatepage_listsetall start
    16/05/2010 07:10:39 kernel hibernatepage_listsetall time: 244 ms
    16/05/2010 07:10:39 kernel pages 517502, wire 44961, act 186001, inact 94850, spec 2, zf 650, throt 0, could discard act 121084 inact 53722 purgeable 10262 spec 5970
    16/05/2010 07:10:39 kernel hibernatepage_listsetall found pageCount 326464
    16/05/2010 07:10:39 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 07:10:39 kernel IOHibernatePollerOpen(0)
    16/05/2010 07:10:39 kernel writing 326232 pages
    16/05/2010 07:10:39 kernel image1Size 89736192
    16/05/2010 07:10:39 kernel PMStats: Hibernate write took 12150 ms
    16/05/2010 07:10:39 kernel all time: 12150 ms, comp time: 2454 ms, deco time: 0 ms,
    16/05/2010 07:10:39 kernel image 674849792, uncompressed 1336610816 (326321), compressed 672248688 (50%), sum1 469cef40, sum2 aeaa70ce
    16/05/2010 07:10:39 kernel hibernatewriteimage done(0)
    16/05/2010 07:10:39 kernel sleep
    16/05/2010 09:10:39 kernel Wake reason = RTC
    16/05/2010 09:10:39 kernel RTC: maintenance alarm 2010/5/16 07:10:39, sleep 2010/5/16 05:10:53
    16/05/2010 09:10:39 kernel System Wake
    16/05/2010 09:10:39 kernel Previous Sleep Cause: 5
    16/05/2010 09:10:41 kernel Ethernet [AppleYukon2]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,c5e1,2800]
    16/05/2010 09:10:41 configd[13] network configuration changed.
    16/05/2010 09:10:43 configd[13] network configuration changed.
    16/05/2010 09:10:55 kernel hibernate image path: /var/vm/sleepimage
    16/05/2010 09:10:55 kernel sizeof(IOHibernateImageHeader) == 512
    16/05/2010 09:10:55 kernel Opened file /var/vm/sleepimage, size 2147483648, partition base 0xf0c805000, maxio 400000
    16/05/2010 09:10:55 kernel hibernate image major 14, minor 3, blocksize 512, pollers 5
    16/05/2010 09:10:55 kernel hibernateallocpages flags 00000000, gobbling 0 pages
    16/05/2010 09:10:55 kernel System SafeSleep
    16/05/2010 09:10:55 kernel hibernatepage_listsetall start
    16/05/2010 09:10:55 kernel hibernatepage_listsetall time: 245 ms
    16/05/2010 09:10:55 kernel pages 518601, wire 45482, act 186525, inact 94766, spec 4, zf 650, throt 0, could discard act 121083 inact 53749 purgeable 10262 spec 6080
    16/05/2010 09:10:55 kernel hibernatepage_listsetall found pageCount 327427
    16/05/2010 09:10:55 kernel IOHibernatePollerOpen, mlget_interruptsenabled 0
    16/05/2010 09:10:55 kernel IOHibernatePollerOpen(0)
    16/05/2010 09:10:55 kernel writing 327195 pages
    16/05/2010 09:10:55 kernel image1Size 90391040
    16/05/2010 09:10:55 kernel PMStats: Hibernate write took 12158 ms
    16/05/2010 09:10:55 kernel all time: 12158 ms, comp time: 2460 ms, deco time: 0 ms,
    16/05/2010 09:10:55 kernel image 676121600, uncompressed 1340555264 (327284), compressed 673513728 (50%), sum1 26607f1b, sum2 560cf77c
    16/05/2010 09:10:55 kernel hibernatewriteimage done(0)
    16/05/2010 09:10:55 kernel sleep
    16/05/2010 09:32:54 kernel Wake reason = EHC2
    16/05/2010 09:32:54 kernel System Wake
    16/05/2010 09:32:54 kernel Previous Sleep Cause: 5

    Martin Pace wrote:
    If you've selected 'Wake on network access' in the Energy Saver preference pane it is normal.
    http://docs.info.apple.com/article.html?path=Mac/10.6/en/27905.html
    +
    ménage-à-trois wrote:
    Martin Pace wrote:
    If you've selected 'Wake on network access' in the Energy Saver preference pane it is normal.
    ... +if you have a portable computer, selecting this option will wake your computer only if it’s plugged in and the _display is open_.+
    that could be it, turned “Wake for network access” off. will report tomorrow.
    Message was edited by: ChangeAgent

  • I have a problem with my computer recognizing my new iphone when i uninstall itunes and reinstall it does not download properly and bonjour will not load any ideas of what to do

    I have a dell lap top with windows 7 that won't recognize my iphone 5c. The driver's will not install with out a problem, I talked to apple support to try to fix this problem, I unistalled itunes and reinstalled it, now itunes did not download properly, bonjour does not load and i can not burn cds, I have uninstalled and reinstalled twice with the same problem. If anyone can point me in the right direction that would be great

    You are right, but how could i send it to Apple? when the phone company first replaced my iphone they had in stock alots of iphones and they just sent mine back to Apple and gave me a new one, so all i did is to give them my phone, but now how could i sent it to Apple? and i cant send it by myself, and the store wont do that, its a lost for them.. so sending it to Apple wasnt an option from the begining.
    and for the record, i dont think the store where i bought it is an authorized shop.. its just a store who boughts phone's from Apple in a low price and sells it in much more money..

Maybe you are looking for

  • To add condition on which distribution model MATMAS should be sent

    Hello All, I have to send MATMAS Idoc to XI. But in R/3 there 2 distribution models created one for XI and other for some R/# system. I have created a custom report of MASTERIDOC_CREATE_SMD_MATMAS to handle specific conditions. Now I want to send to

  • IPod touch: need to restore to previous update so it will work again on mac computer

    iPod touch: - my iPod has always been used with my desktop iMac computer, which has iTunes version 9 currently installed. It is updated to it's latest possible update, so I am assuming it is not compatible with the latest, iTunes 10. While working on

  • Do I have to install Mountain Lion?

    I have a mac book 10.5.8 and I've been reading around here that to get mountain lion I have to go find snow leopard and then mountain lion. Is this something I need to be overly concerned with? I use google chrome and they have stopped supporting leo

  • Setting up JConsole

    as per J@SE 1.5 to before using JConsole === Start the application with the -Dcom.sun.management.jmxremote option. This option sets the com.sun.management.jmxremote system property which enabled the JMX agent. === how do i set this propery at applica

  • Is JSF 1.0 redistributable for commercial apps

    We need to write a JSF app and plan to use JSF 1.0 but it says they are sun licensed binaries. So do we need some licensing or can we just use them and redistribute them? Please suggest. Thanks