Laptop is not powering on wihout battery and with battery

Hi All,
I have Presario CQ 40-327 TU Laptop and i've been using this since 2009. My lap's batterry is almost dead and not charging up.When i try to poer on my lap it was not powering up. So i removed the battery and plugged in the power cable and tried again but it didn't. What is the reason behind this? Though the battry is removed, it should power on with the charger cable but the same is not happening in my case?Help me out

Thanks for the reply and suggestion.
Finally i have told to replace the battery and adaptor. I've asked them to send me quotation. The quotation as follows.
1 BATTERY (10.8 V = 47Wh)- CQ 40 NOTEBOOK - Make ORG OEM - 1YEAR WARRANTY 1   INR 4000.00
2 ADAPTER Smart pin- CQ 40 NOTEBOOK - Make- HP - 1YEAR WARRANTY 1   INR 2300.00
3 RAM 4 GB DDR 2- CQ 40 NOTEBOOK - Make – Hynix - 1 YEAR WARRANTY   INR  5900.00
* Rates ara in INR (Rupees)
I feel cost is very high!! What will be the cost normally? Why the costs are so high? 4 GB RAM is 5900 Rupees(\INR)??
Shall i go ahead with this or not?? I guess the cost is $71,$31 and $105 respectively.
Please help me out!

Similar Messages

  • Bought a brand new battery from an authorized Apple Premium Reseller but the laptop is not recognizing the new battery

    Bought a brand new battery from an authorized Apple Premium Reseller but the laptop is not recognizing the new battery

    Yes, it says no battery installed. The battery icon with an X and system profiler saying no batter installed.
    Tried the SMC Reset - didn't work!

  • Power Mac G4 MDD not powering up after battery change and pci reset

    First my clock was off. Then iTunes 9.0.3 problem - error message 'this copy of iTunes is corrupted or installed incorrectly. Need to reinstall.' I uninstalled iTunes according to the KB instruction. Then 9.1 install failed. This is the beginning of nightmare. Everything I tried failed thereafter.
    I thought the low battery might be partly or solely responsible for this behavier. So I bought and installed a new battery. After that my Mac was OK for about one hour. Then I was trying to use Disc Utilities using the installer disc to check the HD's health. It failed. I started up to the internal OS. I used fsck. Came up the message saying 'This volume of the HD could not be repaird.' I repeated restarting a few times altogether. Finally, it quit booting. Precisely it boots up to gray screen with Apple logo with a daisy spinning underneath (for a long time). Then the screen turned blue and a cursor blinked periodically. Tried a couple of more times. Same thing ...
    So I reset the PCI (PMU). Nothing has changed. Same pretty blue screen. Where can I go from here before I head for Apple Store. Please help.

    I believe that the directory on your hard drive is corrupted & Disk Utility can't repair. DiskWarrior can probably fix your problem. DiskWarrior by Alsoft
    http://www.alsoft.com/DiskWarrior/index.html
     Cheers, Tom

  • [SOLVED] laptops backlight not powering on after suspend

    I'm on the g+ arch community, it seems that a few of us there have an issue with our laptops not waking from suspend, and I've seen a few issues like this, here, on the arch forum.
    http://pastebin.com/eXebMFTy
    This is my dmesg after the said issue occurs...
    I'm on an intel macbook 4,1 with kernel 3.15.1-1-ARCH.
    I looked at the arch wiki page about backlights, and it said that I could get info on my backlight drivers at /sys/class/backlight. I'm guessing that since using intel graphics drivers, I should have a directory there called intel-backlight, or intel-dri, or something, but it's empty. This doesn't seem kosher... and it seems that a lot of us on the g+ community are using intel drivers, and this started happening for me after/around-the-same-time-as I did a pacman -Syu that upgraded my intel-dri and xf86-video-intel.
    Last edited by comapony (2014-07-15 22:55:31)

    R00KIE wrote:You first have to determine if the machine really doesn't wake up or if it wakes up but you don't see anything on the screen.
    Sorry, I should've mentioned that, yes, it's just the backlight. If I take a flashlight the to the screen, I can see stuff there, and I can see stuff changing if I were to start scrolling, mashing buttons, et cetera. I can ssh to the machine in question and restart it, I also tried 'xset dpms force on' over ssh, but it fails because it says the display isn't recognized, even if I set DISPLAY manually. Before a suspend, I'm able to 'xset force dpms off && sleep 5 && xset force dpms on' successfully.
    Rexilion wrote:Did this ever work on another kernel version?
    I upgraded to 3.15.2-1-ARCH last night, it didn't have any effect. I'll try a downgrade tonight, and I'll check my pacman.log to see if I had a kernel upgrade around-the-same-time-as the backlight started fucking up.

  • LAptop does not let me past Username and Password

    Hello,
    please help. My computer's 5 yrs old and playing up. AT start up, it prompts me for the usual USERNAME and PASSWORD details. I fill those in (the same I've had for 5 years, the system recognises my account, shows the right picture (of a cat and then the screen goes blue and returns back to the USERNAME and PASSWORD page. I;ve tried restarting, disconnecting all attached equipment, taking the battery out, but nothing helped the problem.
    It all started after the regular software update check and installment of software updates offered.
    HElp please.
    Thank you in advance/.
    p

    Try using Disk Utility to repair your startup disk (hard drive) as shown in Dr.Smokes Resolving Disk, Permission, and Cache Corruption.
    Let us know what problems it reports, if any.
    Cheers!
    DALE

  • Firefox stopped working on laptop but not desktop, have completely uninstalled and reinstalled but it still won't work, please can anyone help as i hate using IE.

    the program was working fine then suddenly wouldn't connect to anything. have unistalled everything including passwords, add-ons etc and reinstalled but still no joy.

    Hi kjohns2001,
    Welcome to the Support Communities!
    If you do not have an iPhone, iPad or iPod touch, then you don't need iCloud.
    It is a service that keeps these devices and your computer synchronized.
    iCloud Control Panel 3.0 for Windows
    http://support.apple.com/kb/DL1455
    iCloud keeps mail, contacts, and calendars up to date between your iPhone, iPad, iPod touch, Mac, and Windows PC, and lets you share calendars and task lists.
    So, you can uninstall it from the Control Panel in Windows.
    Cheers,
    - Judy

  • The trackball on my Lenovo laptop does not work to move up and down pages on the Firefox Beta. Can I enable this

    The problem started when I downloaded the Firefox Beta version 4. I have just upgraded to version 5 and I am still having the problem. I have a center button on mouse pad that allows me to move up and down pages without clicking on the sidebar,

    Try this: <br />
    Type '''about:config''' in the URL bar and hit Enter. <br />
    ''If you see the warning, you can confirm that you want to access that page.''
    '''''Filter''''' = '''trackpoint'''<br />
    '''''Pref''''' = '''ui.trackpoint_hack.enabled''' <br />change that from -1 to 1. <br />Restart Firefox.

  • HP Envy Laptop will not Wake up from Sleep Mode with Windows 10

    The reason I decided to go back to windows 8 was because since upgrading to Windows 10, when my computer goes into sleep mode, I cannot wake it up. I have to press and hold the power button to shut it done and restart. Even if I close my laptop, and reopen the lid, it wont start back up and I have to press and hold the power button and shut it down and restart.  After trying to restore my HP Envy Laptop from Windows 10 to Windows 8, it got stuck in a Repair PC Loop and I could not even access the desktop, I tried the restore option to an earlier date and that failed and all the repair options also failed. The last option I had was to do a full PC Refresh, and that one worked. It took about an hour but no data was lost, and only a few of my downloaded apps were removed. An html url was left on the desktop that showed a list of all the apps that were removed. So all I did was download those back and now im back up and running Windows 8.  I want to re-download Windows 10, does anyone have a fix for this issue?

    Hello mistyb1,
    Welcome to the HP Forums.
    I see that you are having an issue with the printer not waking up from Sleep Mode.
    I do have a few suggestions that we can try.
    First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
    Once you have the printer connected to the wall outlet, please use the ON/OFF button to do a proper power cycle.  This will do a Semi power reset on the printer.
    If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
    Thanks for your time.
    Cheers,  
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • New Mac laptop will not connect to router wireless, fine with ethernet

    D-Link DSL 2640B

    Hey jannafromaz,
    Thanks for the question, and welcome to Apple Support Communities.
    The following articles may assist you in troubleshooting your network connectivity issue:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT4628
    Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection
    http://support.apple.com/kb/TS1317
    Thanks,
    Matt M.

  • Laptop not even a year old and the power cord is stripping really bad and barely working

    My toshiba laptop is not even a year old and the part of the cord closest to my computer is becoming really stripped. I noticed that it got very hot during pc use, I just assumed that was normal, but I'm starting to think that this heat made the rubber very soft and caused the cord to strip. I guess my question is, do you think toshiba will replace this or will they just say that it was my fault that it happened?

    You can either use a cloud service like Google Drive, or use the built in Verizon Cloud Backup, or you could plug the phone into a computer and use it like a USB drive and copy the photos from there to the PC.  Your contacts are backup up through Google if you've been saving contacts to your Google account, otherwise Verizon has a backup on the phone as well and when you restart the phone after wipe you can select either or both accounts to restore from.
    To factory Reset:  Go to Settings (pull down notification bar click on gear top right corner).  Then go to Back up and Reset.  At the bottom is Factory data reset.  Press that then press reset phone.  It WILL be completely wiped, but it will keep the current OS version.  It'll be like you just bought it.

  • Dv7-1025nr not powering up

    My laptop does not power up at all.  I removed the battery, and unplugged the power adapter, held down the power button for 30 seconds to drain any build up.  Then I plugged in the power adapter (only the power adapter, NO battery), and pressed the power up button to turn the laptop on, but nothing powers up at all..NO lights or LED's come on.  Only light that glows when I plug in the power adapter, is the small light near the power input hole where the adapter connects to the laptop.
    I replaced my power adapter with a brand new one (original equipment) and the same thing happens.
    What is the next step in troubleshooting this problem?

    Hi there @gd2554,
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that your notebook is not powering up at all, and that you have replaced the power adapter with a new one. I am happy to help.
    Are you connected directly to a wall outlet or going through a power bar?  If possible use a direct power connection.
    Next, if you haven't already, try using a different power outlet entirely.
    Did you replace the entire power adapter including the power cord (assuming it is one of the adapter with a brick and a removable cord going to the wall outlet? Be sure to use the replacement cord as well, if you haven't already.
    Then try going through all of the following:
    Computer Does not Start (Windows 7, Vista, XP)
    Battery Charging Is Not Indicated in Vista or Charging LED Does Not Turn On
    If there is no sign of life then it is likely the issue is on the main board of the notebook itself, in which case, I would recommend, calling our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Compaq Prepares CQ61-320SA not powering on.. tried hard reset.. :/

    1. Product Name and Number
         • Compaq Presario CQ61-320SA
     2. Operating System installed (if applicable)
         • Windows 7 Home Pre 64-bit
     3. Error message (if any) 
    > Unable to turn on the laptop.. 'Power' light flashing all the time.. AC Adapter light turned on at the socket where its plugged in..
    > Bizarrely, Laptop is not turning on without battery and only AC adapter plugged in.. no lights except the AC adapter light at the socket..
    > RAM.. :/ Removed 'both', cleaned them, swapped slots.. used just one (both modules in both the slots individually)
    > My battery replacement part number is: 484170-001.. just to give an idea what kind of battery i might be having..
    1) My first question is, Does my laptop model work with only AC plugged in with out battery? IF so does that mean my laptop system board died on me?
    2) Can I order a board on my own? does it have to be the same model number? or may be a different similar board that may be cheaper?
    3) or is it just the power jacket or slot issue?
     4. Any changes made to your system before the issue occurred
         • Always runs hot at about 80 to 85 Deg C.
    Thanks,
    Much appreciated of your time.
    Sid

    Bumping up.. Please suggest something.

  • My MP990 will scan using my Win 7 laptop but not with my XP desktop

    I have been running my MP990 using a WiFi connection. I had to replace the printer with another MP990. I can still use the scanner function using the Win 7 laptop but not on the desktop XP. With XP, I get the following message:
    Cannot comunicate with scanner for these reasons:
    - Scanner is turned off
    - Scanner is disconnected
    (It is disconnected from LAN, if using on LAN)
    Please check and try again
    Scanner Driver will be closed
      Code:5,145,55
    Since it will scan using the Win 7 "Windows Fax and Scan" but will not work on the desktop XP, I suspect I need to re-install the software. I don't have the orifinal disk but I did download  a couple of files: MP990soswin100us.exe or mpnx_3_0-win-3_05-ej-exe
    Can I just run one of the above .exe files to take care of my problem?

    Hi gooch,
    I recommend installing both of the files you mentioned as one is the driver and the other is MP Navigator.  The driver will get the basic files installed, but the MP Navigator gives you an easy to use interface to power the scanner.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • HP Pavilion battery healthy and charged but laptop is not running on battery

    A serious and odd problem has developed with my Pavilion (HP 15-N096EA PC)
    I removed the battery when the machine was switched off and pressed the start button as this procedure was suggested on a site for clearing malware issues.
    Since then, my laptop has refused to run on battery. Behaves as if there was no battery in it. The Pavilion is relatively new, the battery is in perfect condition, charges to 100% and keeps the machine running for up to 6-8 (!) hours. Not kidding.
    Even now, the mains connection charges the battery, the little icon says so in the system tray. It is now 100% charged.
    But when I unplug the mains adaptor the whole thing dies immediately.
    I applied electric contact cleaning liquid to the connection ends of the battery, even measured the voltage in the battery with the tipped ends of a volt meter. All reading perfect values, yet the computer has stopped working from battery.
    An hour ago this computer worked completely well on battery, but since the current "draining" exercise absolutely nothing. Tried all sorts of options: Taking battery in and out while on mains, nothing doing. If I am correct, battery calibration can only happen with the computer running on battery and this computer refuses to run on any battery.
    What has happened here please? ANY HINT,ADVICE, SUGGESTION from professionals, non-professionals most desired and appreciated. Thanks.

    Hi @Squinancy 
    Welcome to the HP Support Forums!
    From your description it sounds like you were try to do a hard reset of your notebook to start with, but it is possible it was not done properly. Read through this, and try it again.
    HP Notebook PCs - Use Hard Reset to Resolve Hardware and Software Issues
    If after that the computer is still not booting up on battery, check through this one next.
    Battery does not power the notebook or hold a charge
    Let me know how it works for you, and if you have more trouble please post any other details you can.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?

    dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?
    It lights up initially for a split second when I push power button, but does not continue to boot up. When ac adaptor is put in it glows blue like it is supposed to. Any suggestions?

    i'm going to try to see if a different ac adaptor will work hopefully that solves the issue.

Maybe you are looking for