Laptop sleep mode

 How can I set up my Lenovo G50 laptop so that I login in the morning, leave the laptop on during the day in a sleep mode so that when I return to it at various times during the day, press any key to wake it up without the need to enter my password again.

Welcome to the Lenovo Community !
I'm assuming that you are using Windows 8.1.  For that operating system please see my link below and just follow the instructions listed for "Manually Make Windows 8.1 Auto Logon After Sleep."
http://www.thewindowsclub.com/auto-logon-after-sleep-windows-8-1
For Windows 8 & 7, see refer to this link......
http://www.thewindowsclub.com/disable-login-sleep-windows-7-8

Similar Messages

  • Closed laptop sleep mode

    Is it safe to just close the laptop and put it in sleep mode for moving it around o taking it to work?, some people say is unsafe because the hard drive, as the only moving mechanical part, can get damage because of this movement. I think it`s safe because the hard drive shuts down completely. It is common for me to use the laptop this way, I mean not shuting it down always, I prefer just to closed it, how about you?

    JETOBAR,
    My Macbook Pro has never been shut down. Never. And, it has traveled with me, more than twice, all the way across this country (US). I figure it has traveled around 25,000 miles, just since this past March.
    It is perfectly safe to simply sleep your Macbook Pro.
    Scott

  • Windows 7 64 bit, CP1525NW wireless install,laptop sleep mode, now no wireless printing

    I installed my HP CP1525 wireless printer  through  my Windows 7 64 bit computer to run wirelessly on my home network and it seemed to print fine wirelessly for mine and my wife's laptops and my iPad2. I put my computer into sleep mode and now today the wireless printer connection through my computer to the printer cant be found

    Yup, with printer sharing, the PC cannot be asleep if the printer is attached to the PC via USB.
    Since this is a network (wireless) printer, why not attach the printer to your wireles network direclty?  Am I understanding the setup correctly?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • MOVED: CX600x Laptop sleep mode problem? Help please

    This topic has been moved to MSI Notebook.
    https://forum-en.msi.com/index.php?topic=144010.0

    i have the same problem, I close the lid to make my macbook go to sleep, but when i open it up even though i hear the sounds it makes when it wakes up, the screen stays black, so i myself have to reboot the system loosing everything i was working in order to log back into the system.
    But i have a problem, i dont have apple care! so i cant call apple for support, but i do know that these machines have a one year warranty, so would this problem fall under that category?

  • HT204074 Watching a TV series, purchasing them one Ep at a time. Anyway after watching Ep3 I purchased Ep 4 but got a call so my laptop i went into sleep mode. Just came back n now it says that 90 days

    'You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 67 days.'
    What is this? It's the most frustrating thing, and I just wnt to scream 'I DIDN'T'. 23 days ago I did because I was unaware of the new 90 day rule.
    But this time, i didn't do anything. I was watching a TV series, and I was purchasing the episodes one at a time (in hopes that this would encourage me to stop and go to sleep after i finished the next one). Anyway I had just finished watching episode 3 and purchased 4 and it had begun to download, when I left my laptop to go get something to eat came back n it had obviously gone into sleep mode. so had to continue the download BUT when I try to continue the download the 'message' pops up. I haven't signed out, it's purchased under j_akale, so I don't understand.
    <Edited by Host>

    Frist tip, after installing software updates (I assure your machine started off with 10.4.2 and when you first used it, you were promted to update to 10.4.4.), go into the utlities folder (under applications) open disk utlitity and verifity and repaire disk permissions, this will greatly boost preformace and may fix your problem. (In fact do this once a week) Go ahead and run the Techtool (Applecare hardware test CD) and check for any problems. If these come up with nothing, I'd call Applecare and tell them what is happening. Applecare will cover you at any Apple dealer and some Apple resellers as well. Going elsewhere will kill your warrenty BTW.

  • I got a Macbook Air. My system language is russian but the login password is english. I pu the laptop into sleep mode, then wanted to log in again, but the language seems to have switched to russian, there's no language change button! How do I log in now?

    I got a Macbook Air. My system language is russian but the login password is english. I put the laptop into sleep mode, then wanted to log in again, but the language seems to have switched to russian, there's no language change button! How do I log in now?

    Severia,
    I tried your solution, but it did not work with my laptop. After I restart the laptop, the language does not change and I cannot type the password in English language. Do you have any other suggestion?
    Thank you.

  • Laptop won't wake up from sleep mode

    I have a Satellite L745-s2410 and usually whenever i close the lid to my laptop it goes into sleep mode and the orange light comes on and whenever I open it up again it would come back on (either automatically or just by moving the mouse or pressing the power button). However as of last week I noticed that when it goes into sleep mode it only comes back once. If i put the laptop to sleep again it will not come back and I am forced to either take out the battery or hold down the power button to turn it off. If you can please help me that would be great
    Thank you in advance, 
    Eric

    Did this just start?
    Try this. Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections. Then test it again.
    - Peter

  • Laptops not reporting when coming out of sleep mode

    Currently I have set my schedule so that Laptops inventory on a weekly basis. Our users will routinely place their laptops in sleep mode at the end of the day instead of turning them off due to the long log-in times in the mornings. When the user reconnects in the morning their network connections are restored and they continue on as normal. The problem is ZAM thinks that the device is NOT connected to the network and is unable to inventory it according to its schedule. Once the user does a complete reboot then ZAM is fine until the next time the device is placed in sleep mode.
    I believe the problem is due to ZAM holding onto the old IP address and not seeing the device when it connects through the newly acquired IP address.
    Is there something to that can be changed in the manager that I have not found yet? Any suggestions?

    Hi,
    DaryRo wrote:
    >
    > Yes the devices have a local firewall installed however they have the
    > appropriate ports open to allow the ZENworks Client to pass through.
    "Can you try without it"?
    > The problem appears to be that when the laptops acquire a new IP Address
    > the next day that the Client never releases the old IP Address and
    > cannot resolve until it process is restarted.
    I doubt that. As I said, this doesn't match my results, and of course I
    *do* acquire a new IP, in fact in my case it's even three of them
    (local, home, VPN). What makes you think that's the case?
    > I can have our system architects write a small script to reinitalize
    > the client when the laptop reconnects but I don't think that should be
    > necessary.
    Right.
    > Is there a setting in the Manager that would make the client
    > do this?
    No, it does it automagically.
    CU,
    Massimo Rosen
    Novell Product Support Forum Sysop
    No emails please!
    http://www.cfc-it.de

  • Laptop shuts down after sleep mode, help please!

    When I close the lid or press the sleep mode button, my laptop goes into sleep mode and everything is ok. However, when I open the lid or press the power button to awake it... after a few seconds, my laptop shuts down! I just formatted my laptop to the factory settings hoping to fix the issue, but it persists. Please help!

    When any problem persists after recovering to factory settings, it's often indicative of a hardware problem.
    Please contact support at (800) 457-7777.
    - Peter

  • G505s Laptop shuts down in sleep mode

    Hi,
    I recently bought a new G505s laptop running Windows 8.1. When the laptop goes into sleep mode  (either on the battery or when plugged in with the lid down) the laptop will shut down completely. It does not even seem like the laptop is going into hibernation since Windows begins from a cold boot when powered on. Oddly, with the power cable plugged in the laptop will not even power back on. I have to remove the cable and power the laptop back on using the battery.
    It seems to be a relatively common problem with Win 8.1 and there are various fixes people have suggested. So far I've tried reinstalling & updating AMD drivers, setting the power options to never hibernate and running a script to turn off hibernation.
    None of these fixes have worked and the laptop will not stay in sleep for more than 20 minutes before shutting down completely.
    I wondered if anyone else has encountered this problem with the same or similar model and whether there are any other fixes people suggest?
    Thanks,

    Bump

  • Wireless not working after laptop wakes up from sleep mode

    After my laptop wakes up from sleep, the wireless network stops. Even when the wireless is enabled, it is unable to scan the wireless networks. In order to make it working again, I have to restart my laptop. Here are some of the details that might be useful.
    %lspci | grep Network
    03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
    %rfkill list all
    0: phy0: Wireless LAN
            Soft blocked: no
            Hard blocked: no
    1: hci0: Bluetooth
            Soft blocked: no
            Hard blocked: no
    %iwconfig
    lo        no wireless extensions.
    eth0      no wireless extensions.
    wlan0     IEEE 802.11bgn  ESSID:off/any 
              Mode:Managed  Access Point: Not-Associated   Tx-Power=14 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:off
    %iwlist wlan0 scan
    wlan0             no scan results
    %ifconfig
    eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500  metric 1
            ether e0:cb:4e:fe:e2:00  txqueuelen 1000  (Ethernet)
            RX packets 0  bytes 0 (0.0 B)
            RX errors 0  dropped 0  overruns 0  frame 0
            TX packets 0  bytes 0 (0.0 B)
            TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
            device interrupt 45 
    lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 16436  metric 1
            inet 127.0.0.1  netmask 255.0.0.0
            inet6 ::1  prefixlen 128  scopeid 0x10<host>
            loop  txqueuelen 0  (Local Loopback)
            RX packets 336  bytes 26572 (25.9 KiB)
            RX errors 0  dropped 0  overruns 0  frame 0
            TX packets 336  bytes 26572 (25.9 KiB)
            TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
    wlan0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500  metric 1
            ether 1c:4b:d6:75:ae:67  txqueuelen 1000  (Ethernet)
            RX packets 22619  bytes 27403217 (26.1 MiB)
            RX errors 0  dropped 0  overruns 0  frame 0
            TX packets 22393  bytes 2574830 (2.4 MiB)
            TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
    /var/log/messages.log: (from the point where the laptop goes to sleep and wakes up)
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): now unmanaged
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): device state change: activated -> unmanaged (reason 'sleeping') [100 10 37]
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): deactivating device (reason 'sleeping') [37]
    Dec  9 12:28:12 localhost dhcpcd[1927]: wlan0: removing interface
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): canceled DHCP transaction, DHCP client pid 1927
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): cleaning up...
    Dec  9 12:28:12 localhost NetworkManager[745]: <info> (wlan0): taking down device.
    Dec  9 12:28:13 localhost NetworkManager[745]: <warn> (pid 1927) unhandled DHCP event for interface wlan0
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): now managed
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): bringing up device.
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): preparing device.
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): deactivating device (reason 'managed') [2]
    Dec  9 12:28:25 localhost kernel: [ 3612.851109] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): supplicant interface state: starting -> ready
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
    Dec  9 12:28:25 localhost NetworkManager[745]: <info> (wlan0): supplicant interface state: ready -> inactive
    %uname -r
    3.1.4-1-ARCH
    %uname -m
    x86_64
    I want to know what is going wrong here. Any help/suggestions will be useful.
    Last edited by geeky_sh (2011-12-09 07:27:37)

    Well, the above two links have the problem similar to mine but not exactly. In first one there is a problem with network manager - that it is unable to restart after coming from sleep mode while that is not a problem in my case and I tried all the solutions provided in the second link, but didn't work.
    What I figured is when I execute '#pm-suspend' and then close the lid. Then, after I open the lid I wireless works fine. 'pm-suspend' is not invoked if I close the lid. So I needed to invoke the above command when an acpi event is generated when I close the lid. So here is what I added in the /etc/acpi/handler.sh file
    button/lid)
         case "$3" in
               close)
                   (sudo /usr/sbin/pm-suspend)  #added
               open)
    This works fine for now. Still, I don't know why this solution works - Why executing pm-suspend solves my problem?

  • Firefox hand every time when laptop exit from sleep mode. Tested on 5 laptops with windows 7.

    Firefox hand every time when laptop exit from sleep mode. Tested on 5 laptops with windows 7.

    Same exactly problem here, very annoying when the computer goes to sleep mode and then Firefox locks up.

  • My laptop wont wake up from sleep mode

    Hello, I hope you can help me!
    I have this problem: When I set my laptop to sleep mode or I close my laptop (I have set "sleep" asi action after closing the laptop) it just wont wake up... I open in - nothing, I try to push the button for starting - I can hear it booting, but after few seconds the laptop is quiet again and nothing happens.
    All I can to do is trying to turn it on over and over again and after 10 tries it finally starts. Sometimes helps plugging or unplugging the charger.
    I don't have this problem with hybernation mode.
    I own ThinkPad E535.
    I hope it's Windows 7 problem or something with drivers. Or do you think it's a problem with BIOS? I hope not.
    Thank you for advices!
    (I'm sorry for my poor English, it's not my first language.)

    Hit me over the head enough times with a fact and it will sink in.
    In the front right corner where your right wrist sets when typing there is a light in the dot of the i in Thinkpad. When the computer is asleep, what is that light doing? When you try waking up the computer and the screen is black, is the light doing anything?
    Do you have the power manager installed?
    Hoov
    Microsoft MVP - Consumer Security
    SpywareHammer.com

  • Laptop won't go to sleep mode and shut down properly.

    hello,           My name is Atul and i upgraded my laptop hp pavilion 15-p017tu from win 8.1 to win 10 on 29h july. My laptop was working great before the upgrade and before upgrading i updraded ( updated ) all the drivers and windows too.          so, after the upgrade i have been facing the same problem which has been shared by many peple here..i.e win doesn't go to sleep mode. In my case when ever i put the sys to sleep mode, the screen turns off but the power button doesn't blinks and i can't go back to the normal mode by using mouse curser or pressing the power button back. I have to physically shut down the system by pressing the power button for 5 seconds.         Also, my system won't shut down properly and it is the same as the sleep mode probem. I have contacted the customer care of microsoft and hp both and they did some setting changes but the problem keeps coming back. I have also told by the hp care that they will take atleast a month or two to fix this as this may be due to hardware not supporting the current driver so this might take time. They also told me to just downgrade to win 8.1 and after sometime when this poblem is fixed i can again install and upgrade win 10. If any of you guys know how to fix this problem do share it here.      thanks!!

    Hi ,
    Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
    I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion 15 p017tu Notebook and issues with the sleep mode and shut down not working correctly. Go into the Device Manger and go to display adapters. Update the driver. Select the Automatically search for updated drivers.
    Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating after Windows 10 upgrades . I hope this helps. Thanks.

  • Laptop doesn't wake after sleep mode after Windows 10 update

    I usually lower the laptop lid when i want to put it into sleep mode; after the windows 10 update, this stopped working. I tried putting it into sleep mode from the start menue. This causes the screen to become black, but power to remain on ( I can see this from a steady light from the power button whereas sleep would have a flashing power button). The laptop's fan also increases in speed. When I try to wake the laptop, nothing happenes; I have tried to use ctrl+alt+delete, however this also does not work. I am ususally forced to resort to a manual shut down via holding the power button for a few second and restarting the laptop. I have tried updating the display adapters, restarted the laptop, and still no result. Does anyone know why this is happenning and how I can fix it?

    I was having the Exact Same Issue. The reason I decided to go back to windows 8 was because since upgrading to Windows 10, when my computer goes into sleep mode, I cannot wake it up. I have to press and hold the power button to shut it done and restart. Even if I close my laptop, and reopen the lid, it wont start back up and I have to press and hold the power button and shut it down and restart.  After trying to restore my HP Envy Laptop from Windows 10 to Windows 8, it got stuck in a Repair PC Loop and I could not even access the desktop, I tried the restore option to an earlier date and that failed and all the repair options also failed. The last option I had was to do a full PC Refresh, and that one worked. It took about an hour but no data was lost, and only a few of my downloaded apps were removed. An html url was left on the desktop that showed a list of all the apps that were removed. So all I did was download those back and now im back up and running Windows 8. 

Maybe you are looking for