Laserjet 2100 TN via ethernet to MacBook Pro 2009 (Snow Leopard)
I've been given an HP Laserjet 2100 TN. It was previously suceessfully used with a MacBook pro via an ethernet cable.
I'm trying to set it up at home but failing to get it to connect with my MacBook. I'm using Snow Leopard.
I've read lots of connection tips in discussion forums but not found a solution that works for me.
I've managed to print a configuration sheet which tells me in printers HP JetSend Address.
I've tried using this to add the printer through System Preferences but the computer is not connecting with it.
Do I need a parallel cable or is the ethernet cable enough?
I think I'm missing something obvious!
Sarah
Sorry to post in the wrong place! And thanks for your input. SCSI is a good call - the parallel cable didn't look quite right and that may explain why. Can I add a few more experiences to help explain where I'm at:
- Snow Leopard seems to think the drivers should be included in the OS, but I don't know how to access them.
- I found and installed a driver but couldn't find how to access it when adding the printer.
- When I'm in ADD PRINTER
- I guess I need an IP address - is this the one I find on printer info?
- I saw a forum that recommended LPD as best choice for old priters so I'm using that
- It defaults 'Print using' to Generic Postscript Printer'. I've tried changing it to Generic PCL Laser Printer as it is a laser prointer, but neither help make it work
- Once I've setup the printer, when I run a test page the printer fails to connect and goes on hold
I don't think I'm explaining myself very well - mainly because I'm quite out of my depth trying to did this! I can't find anything in the printer handbook which helps. Do you have any advice for a novice trying to add a printer it would be much appreciated.
Similar Messages
-
Macbook pro 2009, Snow Leopard, freezes
Hello everybody,
Until yesterday no problems at all, never.
Yesterday I have opened Parallels, Entourage, Safari and it blocked.
My windows is pretty lame so I waited for it to stop.
After 1 hour I stopped it from the button.
When I have restarted the first surprise was that the dock is not present.
I went to the system preferences to check it, it froze again, the rainbow wheel keeps spinning endlessly.
I have stopped it and restarted it several times, nothing.
One friend had the idea to take off the batery and plug it in again. I did that, same thing.
I am not a 'clever user' I don't have any idea about the inside of the OSX, terminal, console, I have read some of the discussions and I am lost :h.
Can someone have the patience to try and explain me some things that I can try?
Thank you
P.S. I am not sure if it was 10.6.7 or 10.6.8 when it crashed. In the mean time it made an update and it is currently 10.6.8There is a issue with 10.6.8 and Parallels, run the update.
http://blogs.parallels.com/consumertech/2011/6/24/workaround-mac-os-x-1068-perfo rmance-issue.html
http://blogs.parallels.com/consumertech/2011/6/30/pd6-update-fixes-mac-osx-1068- performance.html -
I upgraded the operating system on my MacBook Pro from Snow Leopard to Lion via the web. Now I need to erase the hard drive and restore it to factory settings, so that I can pass it on. How do I accomplish this? When I insert the Mac OS X install disk, the only option is to erase the free space. Any insight would be appreciated.
Thank youYou need to boot off the original Snow Leopard DVD's that came with the system.
Once you are running off of the DVD you will be able to do a clean install of SL
To boot off the DVD with the system up running Lion insert the DVD. Open Sytem Preferences->Startup Disk and select the DVD then restart the machine.
Message was edited by: Frank Caggiano -
HP 1312nfi Multi-funtion printer & brand new Macbook Pro with Snow Leopard
Hi,
I just got my Macbook Pro with Snow Leopard May 2010. I can only print and fax with my 1 year old HP 1312nfi color laserjet multi-function printer. I cannot SCAN at all. I tried loading the software that came with the printer but it wouldn't install the 'Print Director' as I had on my old iMac (with Leopard). Then I went to HP and it said not to install the software that came with the HP printer because Snow Leopard has it all. I read that there are 3 ways to scan from my computer which none of them work. I brought up the printer then clicked printer setup and when I try to bring up the 'print utility' from the last tab, it won't open anything. Where is the printer utility now? Why can't I scan? There has to be a way. HELP please?Found the answer on the HP site. It's the original software that works with this printer OS X 10.6!!
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en &cc=us&prodTypeId=18972&prodSeriesId=3558902&prodNameId=3562006&swEnvOID=219&swL ang=8&mode=2&taskId=135&swItem=ma-60835-3 -
What Is Memeo Backup and why is it on my MacBook Pro w/ Snow Leopard?
What Is Memeo Backup and why is it on my MacBook Pro w/ Snow Leopard? Does it slow down my Mac? Seems like someting has slowed down my Downloads, Updates, Backups, etc. & I don't know how to locate the source or how to fix. Any Wizards avail to share some Wisdom? I am using Ethernet Cable/Port for Internet Connection, I Use a Seagate FreeAgent Go Flex Ultra-Portable Drive w/ Seagate's Firewire Adapter Cable.
If this is really Memeo Backup and you want to get rid of it for a better backup program like Carbon Copy Cloner the the following shows all the stuff that Memeo Backup installer installs (based on Memeo Backup 2.5.141 which I found with a google search and downloaded):
The primary file to disable Memeo Backup would be that file in LaunchDaemons. Remove it and reboot and the rest is just taking up disk space. -
My iphone is not listed as a device in the itunes side bar after i plug in to usb port? It used to show up fine - only change I think is that I upgraded macbook pro to snow leopard? Any ideas of what I might need to do?
http://support.apple.com/kb/HT1747
follow this link. see if it helps. -
I'm using a macbook pro, running snow leopard. Yesterday I got around to emptying my trash for the first time in quite awhile and was surprised by how much there seemed to be in there. Immediately after a question mark symbol appeared on all my hard disk folders. If I click on these question marks I get a message saying ' the item can't be found'.
mpagan47 wrote: a question mark symbol appeared on all my hard disk folders.
Not sure where these hard disk folders are located that you are referring to? Finder, Finder tool bar, Finder side bar, Desktop, Dock?
More then likely they are an alias that not longer point to the orginals, thus the question mark.
I would reboot. Delete icons if an alias and just recreate by dragging from the source. Try right click (control) click to remove. -
I have a new l7 Macbook Pro running snow leopard. When I tried to to install windows 7 32 bit on bootcamp, I kept getting a flicking black and blue screen when it tried to install. (Tried several times). I finally downloaded the bootcamp windows support to a flash. I inserted that and finally got it installed. Now when I try to boot into windows I get either a solid black (sometimes blue) or flickering screen and windows will not start up. If I then physically shut down the mac and restart, it will finally boot into windows where it tells me that windows was shut down unexpectently and once I click start windows normally, it will boot up. That will generally let me boot into windows for the remaining of the day. The next day, the same thing happens again. I have tried reinstalling several times, and the same thing keeps happening. It is not my windows disk because it installs flawlessly on the mid 2008 macbook pro. Anyone know how to fix this?
I own HDM 2011. But they have products that aren't listed or hard to find too.
Recommending Pro version for one user's needs:
http://www.wilderssecurity.com/showthread.php?t=297756
Pro vs HDM 2011 feature comparison
http://www.paragon-software.com/home/hdm-personal/comparison.html
Forum topics:
http://www.wilderssecurity.com/showthread.php?t=297756
http://www.wilderssecurity.com/showthread.php?t=303155 -
I have a MacBook Pro with Snow Leopard. After connecting my HP Photosmart D110 to it, the printer works but the scanner doesn't. The message is"The scan cannot be performed because another program has control of the HP imaging device". Can anyone help?
Found the answer on the HP site. It's the original software that works with this printer OS X 10.6!!
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en &cc=us&prodTypeId=18972&prodSeriesId=3558902&prodNameId=3562006&swEnvOID=219&swL ang=8&mode=2&taskId=135&swItem=ma-60835-3 -
I have a couple of questions? 1. I recently updated my old '04 macbook pro to snow leopard 10.6.8, when I went to open an old word doc., it opened with iwork and will not allow me to print until I update to iwork'08. Do I have to update? If I do, is this an update or do I have to purchase iwork? 2. Can I update my old '04 macbook pro to Lion or Mountain Lion or is this too much? I just purchased and iphone 5 but do not know if Snow Leopard can give me the future updates I might need?? Also does icloud work with Snow Leopard? Thanks for help, I am lost...
Try resetting your SMC and NVRAM before attempting to install again.
Resetting the NVRAM/PRAM
Note: This will not delete any data.
The NVRAM/PRAM stores information such as speaker volume, screen resolution, startup disk selection, and recent kernel panic information (if any). You should reset the NVRAM/PRAM if you experience issues relating to these functions.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Turn on the computer by pressing the Power Button.
On the built-in keyboard, press and hold the Command (⌘), Option (⌥), P, and R keys before the gray screen appears.
Continue to hold down the keys until the computer restarts and you hear the startup chime for the second time.
Release the keys on the built-in keyboard.
Resetting the SMC of an Intel-based portable Mac with a battery you should not remove on your own
Note: This will not delete any data.
The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
On the built-in keyboard, press the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
Release the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
I hope I helped.
Austin -
I have a macbook pro running snow leopard. Just recently I cannot view youtube videos and other online videos. I recently updated my flashplayer plugin and I believe that is the problem. Is the latest flashplayer plugin compatible with 10.6.8? If this is so, I need to find an older flash player plugin to reinstall. I do not want to upgrade from 10.6.8 at this time because I have 18 yrs. worth of financial records on Quicken that I have read will not work with Lion and I've read bad things about running music programs on Maverick.
rayvonr wrote:
...I have 18 yrs. worth of financial records on Quicken that I have read will not work with Lion and I've read bad things about running music programs on Maverick.
1) Quicken 2007 for Intel (Snow Leopard, Lion, Mt. Lion and Mavericks) is a full featured app that can be downloaded from Intuit for $15 and will work with your data file if you are using Quicken 2005, 2006 or 2007 (if you version is earlier, let me know for more instructions on easy conversion):
http://quicken.intuit.com/personal-finance-software/quicken-2007-osx-lion.jsp
2) Partition your hard drive, or add an external hard drive and install Mavericks there and "dual-boot" to operate your music programs in Snow Leopard and experiment with them in Mavericks.
DO NOT install Mavericks over Snow Leopard! -
I have a mid 2010 Macbook Pro running Snow Leopard and foolishly upgraded to Yosemite. Now have numerous problems. Is it possible to go back in time with Time Machine and reinstall Snow Leopard? Then upgrade to Lion or Mavericks? Any other ideas on how I can exit Yosemite?
Once you get yourself back to Snow Leopard, if you still want to upgrade somewhat, I would suggest the following:
1. Get an external hard drive that you can use for experiments with new OS versions. You could partition it into 2 or 3 partitions. You could then clone your existing Snow Leopard system to one partition using Carbon Copy Cloner (well worth $40) or SuperDuper ($25).
2. Buy OS X Mountain Lion for $20, through the Apple online store (I don't think it's available through the App Store). Apple has decided to make it very difficult for anyone to get Mavericks unless they have already downloaded it.
You will receive two e-mails from Apple, one containing a PDF with a redemption code, and one with the password you will need to unlock the PDF. Using the code, you will download Mountain Lion from the App Store, where it will appear among your Purchased items.
After ML finishes downloading, its installer app will launch itself. When you see this launch screen, QUIT the install app immediately! Go to your applications folder, find the Install OS X Mountain Lion app, and copy it to a safe location outside of your Applications folder. Keeping one or more copies will allow you to reinstall without unnecessary aggravation if you later need or want to do that. At this point, you can re-launch the Installer in the Applications folder and let it run. You can install it on a clean partition on your external HD, or you can allow it to upgrade the Snow Leopard clone you created on your external drive, or you can do both. This should allow you to test how everything works for as long as you like.
3. If you left yourself a free partition on your test drive, try a clean install of Yosemite and set everything up from scratch (do not migrate anything). This will allow you to see whether your problems with it were related to something in your Snow Leopard system. -
Which final cut is best for macbook pro with snow leopard?
which final cut is best for macbook pro with snow leopard?
Probably FCP 7 which is part of Final Cut Studio 3.
-
We are having old home movies put on DVD's. How do we import them to MacBook pro using Snow Leopard and iMovie 8.0.6? Can watch the movies on the laptop, but they will not import.
We took 3 video cassette 8mm that were recorded in the early 90's to a place that burned the videos onto 3 DVDs. When inserted to our Mac, the DVD player comes on to play the DVD. Opened Quicktime, but can find no way to import. Went to File>Open File>Sony_DVD_Recorder_Volume. Clicked on Sony_DVD-Recorder_Volume and it shows a file named VIDEO_TS. Clicked on that and 6 files showed VIDEO_TS.BUP, VTS_01-0.BUP, VTS_01_0.IFO, VTS-01_1.VOB, VTS_01_2.VOB, VTS_01_3.VOB. Where is DVDxDV?
-
Trying to upgrade a MacBook Pro to snow leopard 10.6.3 and all I after the upgrade is done I just get a blank page withe apple symbol. I've rebooted the computer and nothing happens
Upgrading from which Mac OS X?
Is this v10.6.3 a retail disc?
You can purchase Snow Leopard from the Apple online store > Mac OS X 10.6 Snow Leopard - Apple Store
Maybe you are looking for
-
Hi, am going to generate an HTML report for a table by using below code SET heading off SET pagesize 80 SET MARKUP HTML ON SPOOL ON HEAD "<TITLE>Job Comparison Report</title> - STYLE TYPE='TEXT/CSS'><!--BODY {background: ffffc6} --></STYLE>" SET ECHO
-
Some incoming emails have the comment that Mail is not currently configured to show HTML. Under Mail>preferences>view I have checked the box display remote images in HTML. How do I correct this without having to go to a web link to read the message i
-
How can I introduce in my page an inteligent text that shows the last update the page? Thanks!! MCCG
-
Hi, When is nokia 207 set to release in india, i work in a company where camera phones are not allowed and i need a phone with whats app. Regards, ravi
-
My itunes store is not loading on my iphone
i cant get on to the itunes store on my Iphone. is anyone else having this problem and how can it be fixed? i press on the app it opens and then shuts right down. HELP