Laserjet 4050n basic driver for vista causes crash on print command

This is a printer that works fine with several windows xp systems on the network, but on this LG LGR40 laptop, the print command causes a bluescreen crash. A previous intsallation of different drivers for vista caused the same problem. The OS is completely uptodate. Pls help!!!
Here's the incident report from Vista:
Product
Windows
Problem
Shut down unexpectedly
Date
29/03/2009 9:33 PM
Status
Not Reported
Problem signature
Problem Event Name:    BlueScreen
OS Version:    6.0.6001.2.1.0.768.3
Locale ID:    4105
Files that help describe the problem (some files may no longer be available)
Mini032909-02.dmp
sysdata.xml
Version.txt
Extra information about the problem
BCCode:    1000008e
BCP1:    C0000005
BCP2:    8CBFBC49
BCP3:    A72CFC98
BCP4:    00000000
OS Version:    6_0_6001
Service Pack:    1_0
Product:    768_1

The printer is on the network, so it's directly to IP address.
The driver was installed as admin user
No problem with the printer for >8 years.
No other vista systems. 

Similar Messages

  • Laserjet 2600n network driver for vista 64bit

    Is there any way I can have a network driver for HP Laserjet 2600n for Windows Vista 64bit .

    Vista 64 bit drivers for Laserjet 2600n can be downloaded from the following weblinks:
    http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=446154&p... 
    Refer the following two links to configure the printer on Network
    Link1:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=115&prodSeriesId=...
    Link2:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=115&prodSeriesId=...
    I am an HP employee.
    Regards,
    Vidya
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
    ***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

  • Looking for basic driver for psc all in one 2175 for XP 32 bit. Thank you

    looking for basic driver for psc all in one 2175 for XP 32 bit. Thank you Dont need all the photo suite stuff,just basic scan and print.
    Thanks

    Hi @RUkiddingme 
    You can download the full feature software and driver, and only install the basic driver. In the installation you should see the option for custom software. Here is the link to download the software; rw2_021_w02_enu.exe
    Please let me know if this resolves the issue.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • Where can I download Windows 8.1 32-bit basic driver for HP Photosmart 3310

    Hi, I hope someone can help.
    I've been scouring the HP support site trying to find a download of the BASIC driver for HP Photosmart 3310 for 32-bit Windows 8.1.  I don't want the full istall package, just the printer driver.  I found a 64-bit version, which doesn't work on my system.  
    I downloaded and tried the printer install wizard, which only lets you download the full 434MB software package, which I don't want.
    Thanks! Any help appreciated.

    Hi,
    There is a 32 bit WIndows 8.1 drivers available for download, however it is a full feature software and not the basic drivers. You can try to install it and see if it helps you.
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4157&lc=en&cc=us&dlc=en&sw_lang=&product=4394...
    Thanks.
    I work for HP.

  • I need hp laserjet 1000 series driver for win 8 64 bit

    i need hp laserjet 1000 series driver for win 8  64 bit
    [Personal Information Removed]

    Hi,
    The printer is not supported on Windows 8 or Windows 8.1, a drevice is not available for the OS:
    http://h20564.www2.hp.com/hpsc/doc/public/display?​docLocale=en_US&docId=emr_na-c03450061
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • Still no working driver for Vista

    Heck, at this rate we may be up to RC or RC2 before a working driver is released. I stated in another post that I would not post anymore on this board until a working driver for Vista was released, but was shocked to see that the driver for my Audigy 2 has not been updated and the release schedule still states TBA!!!
    For those who are interested, the Vista Transformation Pack #4 provides the best of both worlds. A very similar look to the Vista GUI and the updates, drivers and support that Windows XP offers.
    Honestly, why spend over $00 for a sound card and then lose most, if not all, of its functionality just to say that you are running Vista. I know that Vista is neat, but it is a resource hog and who wants to use their motherboard's onboard sound?

    Actually the latest Audigy 2 ZS driver for XP works on my Windows Vista Beta 2 build 5456.5.
    I've since reactivated UAC, but not driver signing since several drivers are unsigned.
    But disabling UAC got my whole Audigy 2 ZS Platinum Pro Creative cd installed, with the exception of the DVD-Audio Player. I then installed all the software updates (except the DVD-Audio), and then the latest driver for XP and the AudioConsole that is part of the install. I did need to run the driver setup twice and let it reinstall AudioConsole over the one it installed the first time.
    All works except Soundfont Banks. They don't load, the Soundfont Bank Manager will keep trying to if I start it, but it's a no go. Windows uses only the Microsoft Roland Midi Synth (but it works).
    All EAX stuff in AudioConsole works. The software from the cd works too, but since alot isn't being used they're mostly useless. I just use Windows PlayControl and Creative AudioConsole to control stuff.
    There's a problem with Windows Media Player where visualizations only play with cd's, but not mp3's from the hard dri've. If I toggle the Audio Quality from, say, 6/44,000 to 6/48,0000 (where I leave it), then the visualizations will show for one song then deactivate again. Kind of given up on it as I'm not about to toggle that and reset everything for every song.
    Haven't messed with MediaSourcePlayer yet, except to open it and turn off all the remote control stuff.
    Played some games, some music, some DVD's. Stuff sounds fine. When I plug in my headphones it switches my 2. speakers off correctly.
    I did need to install PowerDVD 6 Deluxe to get commercial DVD's to play. (Adult movies played fine as they're not copy protected.) Weird DRM error in WMP when it tries to play normal Hollywood DVD's. But PowerDVD plays them fine. The PowerDVD 7 Upgrade removes 6, then fails to install. So I needed to reinstall 6, then update it to 2003e again. It works.
    So, it'll be nice to get drivers and software that completely work but until then the XP drivers and most of the software does work.

  • Tecra S10-106 - 3G driver for Vista Ultimate 64bit

    Hello,
    I am owner of a Toshiba Tecra S10-106. Due to the fact that Vista Ultimate 64bit is much faster as Vista business 32bit, I would like to use Vista ultimate 64bit as operating system, but I can't find the 3G driver for Vista 64bit. All drivers can be downloaded from USA in english and can be used in german, only the 3G driver is missing. Can somebody else send me a download link or tell me where I can find a suitable driver for Vista 66bit?
    Thanks in advance.

    Hi
    To enable the card you will also need to install the 3G RF Power control utility which is here at http://support1.toshiba-tro.de/tedd-files2/0/3grf-en-20090217134719.zip.
    That is only half the story as I think you also need to install the Value Added Package here http://support1.toshiba-tro.de/tedd-files2/0/vap-en-20090217134137.zip as this then enables the hotkeys to turn on and off the 3G wireless card.
    Hope that helps.
    Regards
    Phil

  • Compatibility of graphics driver for vista with xp

    I have a HP Pavilion a6320in desktop. It came installed with Vista OS. I have now installed Win XP. Will the graphics driver for Vista:  NVIDIA GeForce 6100 nForce 420, 6150 LE, 6150SE nForce 430, 7100/NVIDIA nForce 630i and 8200, also work for Win XP?
    This question was solved.
    View Solution.

    luit wrote:
    I had simply pasted the name of the graphics driver from the HP download page, that's why the names of all the differing devices appear.
    I had replaced the original motherboard MCP61PM-HM (Nettle2) with ECS GeForce6100PM-M2. I tried installing winXP, but the graphics were hazy and performance very slow. Somebody suggested I need to install the graphics driver. Will the graphics driver you suggested work?
    OK.
    Now that is new information that you should have shared earlier with us.
    You need to use all of the drivers that are available at the ECS website for the  ECS GeForce6100PM-M2 motherboard. Do not use the HP drivers for the replacement motherboard.
    FYI ..Once you replace the motherboard with a different brand than delivered your desktop PC ceases to be an HP desktop PC.
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Problem with finding driver for Xerox Phaser 3117 laser printer.

    Hello!
    I have trouble with finding appropriate driver for my Xerox Pahser 3111 printer. There is no support for iOS on their official support website.
    Thank you for your help.

    Hello there, AnnaVod.
    The following Knowledge Base article provides some helpful pointers for troubleshooting AirPrint on your iOS device:
    About AirPrint
    http://support.apple.com/kb/ht4356
    For best results
    Make sure your software is up to date. For iOS, verify that your device is using the latest version of iOS available and that the app you're printing from is up to date. For OS X, Use Software Update to update OS X and apps you've purchased from the Mac App Store.
    To use your AirPrint printer with Wi-Fi, the printer must be connected to the same Wi-Fi network as your iOS device or Mac, either through bridging, or a direct connection to your Wi-Fi network.
    AirPrint printers connected to the USB port of an Apple AirPort Base Station or AirPort Time Capsule are not supported with AirPrint. Connect your AirPrint printer to your network using Wi-Fi, or connect it to a LAN port on your AirPort device using Ethernet.
    Make sure that your AirPrint printer is connected to your network before attempting to print. Some AirPrint printers can take several minutes to join a network after being turned on.
    If you're unable to print
    Check these things if you are unable to print, or if you see the message "No AirPrint Printers Found."
    Make sure your printer has paper, and enough ink or toner installed.
    Make sure your printer is connected to the same Wi-Fi network as your iOS device.
    Make sure your printer has power and is turned on. Try turning your printer off and then back on again to see if it resolves your issue.
    Check to see if your printer has any error lights or indicators displayed on the printer's control panel. Check the documentation that came with your printer to clear any errors displayed.
    Check with your printer's manufacturer to see if any firmware updates are available for your printer. Check your printer's documentation or contact the printer vendor for more information. A firmware update may be available, even if you just bought your printer.
    Important: Printers not listed in this article are not supported by AirPrint. To search for an AirPrint printer model, use the Find feature of your web browser (usually Command-F) to search the list below.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Need Driver for Minolta PageWorks 20 Laser Printer, Mac OS 10.4.11, G5

    Does anyone have any idea where I can find a driver for the Minolta PageWorks 20 printer? I can't find it on the Minolta site nor in a Google search. Generically it'll work with a LaserWriter driver, but I am unable to utilize the different configurations available on the printer itself (which tray to print from and so forth). Or if it's not available, does anyone know how I can customize the standard LaserWriter driver to run this specific printer? Many thanks!

    Hi,
    I'd try a PPD from another QMS printer, like this one...
    http://www.qms.com/support/currentprinters/mc2200sup.htm
    You can also try hand editing a copy of the Generic one to add/change some features, here's a sample of what the start looks like...
    *PPD-Adobe: "4.0"
    *FormatVersion: "4.0"
    *LanguageEncoding: MacStandard
    *LanguageVersion: English
    *Manufacturer: "PostScript Printer Manufacturer"
    *Product: "(Generic PostScript Printer)"
    *PSVersion: "(2000.0) 1"
    *ModelName: "Generic PostScript Printer"
    *ShortNickName: "Generic PostScript Printer"
    *NickName: "Generic PostScript Printer"
    *LanguageLevel: "2"
    *OpenUI *PageSize: PickOne
    *OrderDependency: 30 AnySetup *PageSize
    *DefaultPageSize: Letter
    *PageSize Letter/US Letter: "level2 {
    2 dict dup /PageSize [612 792] put dup /ImagingBBox null put setpagedevice
    statusdict /lettertray known {statusdict /lettertray get exec /letterR where {pop letterR} if}{letter} ifelse
    } ifelse"
    *End
    *PageSize Legal/US Legal: "level2 {
    2 dict dup /PageSize [612 1008] put dup /ImagingBBox null put setpagedevice
    statusdict /legaltray known {statusdict /legaltray get exec}{legal} ifelse
    } ifelse"
    *End
    *PageSize A4: "level2 {
    2 dict dup /PageSize [595 842] put dup /ImagingBBox null put setpagedevice
    statusdict /a4tray known {statusdict /a4tray get exec}{a4} ifelse
    } ifelse"
    *End
    *PageSize ISOB5: "level2 {
    2 dict dup /PageSize [499 708] put dup /ImagingBBox null put setpagedevice
    statusdict /b5tray known {statusdict /b5tray get exec}{b5} ifelse
    } ifelse"
    *End
    *PageSize LetterSmall/US Letter Small: "level2 {
    2 dict dup /PageSize [612 792] put dup /ImagingBBox [30 31 582 761] put setpagedevice
    statusdict begin /lettertray where {pop lettertray} if lettersmall end

  • I am looking for a Mac driver for a Muratec MFX 1430 printer/fax/copier.  Is there one out there for a Mac?

    Looking for a Mac driver for a Muratec MFX-1430 printer/fax/copier
    is there such an animal out there?

    http://www.muratec.com/new/support/drivers.asp does not appear to support that model at all on the Mac.
    Some open source drivers* may exist to support it.
    * Links to my pages may give me compensation.

  • OS Lion driver for Brother QL-570 Label Printer

    Where to find driver for Brother QL-570 Label Printer ?
    Have been to Brother web site no listing for OS Lion.
    10.6
    10.3,,, etc..

    Also run Software Update, you will quickly find out if the printer is supported in Lion or not. The printer manufactureres supply Apple with drivers so if one isn't avaible via Software Update then Brother isn't supporting the device under Lion. Make sure the printer is connected to the computer and turned on when running Software Update.

  • Laserjet 3100 driver for Vista OS

    Need help finding a driver for my Laserjet 3100 on Vista OS
    Thanks

    DA61--
    Here's another idea, with a caveat.
    **I do not know if it will work. Please create a restore point on your PC before attempting this.**
    Here is a link to the download page for the LaserJet 3200. It is a later version of the 3100.
    http://h20566.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=60706&swLangOid=8&swEnvOid=2093
    Please let me know if you try this and how it turns out.
    Best,
    AlliBee
    I am an HP employee, but opinions expressed here are my own.
    Click the thumbs up + button if I have helped you. Mark Accepted Solution if your problem is solved. If both apply......do both.

  • Nvidia Geforce 8600M GT Driver for Vista

    Hi mac-world!
    I'm using BootCamp to start Windows Vista on my Mac Book Pro. I recently bought a seperate TFT-Display from Belinea, which I connect to my Mac Book via DVI. This isn't a Problem while using MacOS, but in Vista I can't adjust the resolution of the seperate Display to more than 1024x768 px. I already installed the Belinea Driver, but that doesn't solve the problem.
    I am wondering, if I maybe need a driver update for the grafic-card. Unfortunately, Nvidia doesn't provide a driver download, but says, I need to contact my Laptop-Vendor for this issue. I didn't find a driver-download section on this page. Does someone know a solution? Where do I get the new driver?
    Thanks in advance
    regards
    Thorsten

    In my case after going through normal Shut Down procedures, I
    noted that after I go through normal shut-down-from-Windows, the machine does not power off. I can only turn off the machine by pressing the power switch for a few seconds.
    When I do not press this switch, Windows restarts after about ten minutes;
    after, however, I receive a brief report (which I never manage to read in full)
    informing me that a software may not have been properly installed or that I
    need a windows update.
    This problem appeared long after I installed all the software that I use,
    and I have checked whether I'm fully updated (I am).
    Lately when I start-up after experiencing this problem, Windows indicates
    that the problem is caused by an NVIDIA graphics driver and suggests that I
    check for a driver update. I have tried the NVIDIA Website but there was no
    reference to the graphics card installed in my machine, namely GeForce 8600M
    GT - I only found a driver for GeForce 8700M GT.
    I have since solved the problem as rerported in http://discussions.apple.com/thread.jspa?threadID=1492731&tstart=0
    However, I stll wonder why there is no reference to 8600 in the NVIDIA site.

  • Wrong IDE Driver for Vista

    The MS Vista SiS IDE Drivers posted for the MB "655 Max HT Ready" @ here:
    http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=424&kind=1
    ... ARE WRONG!!!
    Actually the driver version is vR2.03 which was created to be compatible with Win2000/XP BUT NOT VISTA!.
    Do not dare to install that driver on ur MB, once it's installed it will KILL ur OS (MS Vista). You wont even be able to access the OS in safe mode, it continues throwing a BSOD that appears some micro-seconds then it reboots automatically the system.
    The people on charge of posting the drivers should be extra careful be4 posting them. It could lead a person to loose all his/her info by only trusting in the drivers posted @ manufacturer's OFFICIAL SITE!
    THESE DRIVERS SHOULD BE REMOVED IMMEDIATELY!! (before it causes more serious damages in people's systems).

    Quote from: tcsenter on 02-March-07, 08:18:53
    Well the driver date is clearly labeled 2002, which ought to have raised a little curiosity or suspicion by any observant person.
    You are totally right also. But that date is refered clearly to the OS stated in the info (OS: Win2000/XP)... so could be the case that by some reason they forgot to clarify the different version for "the 1 released" for Vista.
    In addition, as u can check in a glance, the size of both files is different, which could lead to reinforce my previous theory (they forgot to clarify the driver version for the 1 released for Vista).
    Quote from: tcsenter on 02-March-07, 08:18:53
    There is no IDE driver available that is newer than the one already included in Vista for your SIS chipset.
    Yea unfortunately, I discovered that after damaging my OS. But fortunately I had backed up the OS (by creating an image).
    I mainly created this thread for saving other's people work/life/files ... since I was already saved! 

Maybe you are looking for