Laserwriter Pro 630 with Linksys Router. Do I need a driver?

I have a two Powerbook G4s and a Linksys Wireless G router. I want to use the Laserwriter Pro 630 wirelessly through the router. How do I do this?
I first tried by connecting this printer via ethernet cable directly from my laptop to the printer. The printer has a Farallon ethernet adapter. The computer could not find the printer.
Do I need a driver for this printer?
-Luis
Powerbook G4   Mac OS X (10.4.4)  

To be able to use the printer connected directly to the PowerBook you may need to use a crossover cable if you have an older PowerBook. The driver is built into OS X. Also you need to make sure that AppleTalk is turned on for the ethernet port. See http://discussions.apple.com/thread.jspa?threadID=339353&tstart=0 for details.
To try and set it up wirelessly you will need to switch AppleTalk to Airport and go through the same setup as above. You may not be able to print wirelessly as a lot of routers do not work with AppleTalk. Another possibility is to get a parallel print server, which uses TCP/IP.

Similar Messages

  • My LaserWriter Pro 630 thinks it's a LaserJet IIP and prints dirty pages!

    I recently aquired a LaserWriter Pro 630, and have been trying to get it to work. I've been using it with a WinXP Pro SP2 laptop as my PowerMac G4 doesn't have a parallel port and my print server has not arrived yet.
    Basically, the only time it'll print anything is when the push button on the printer interface rail is set to 1 or 3 - which is PCL output. While the printer will print when set to PCL, it's output is... undesirable. When configured in XP as a LaserWriter Pro 630, it simply starts printing out the raw PostScript sent to the printer! interestingly enough, the printer will print on push button setting 4 - it'll print the printer spec sheet, and nothing else. Anything other than 1, 3, 04 4 will result in the printer thinking for a bit then giving an "out of paper light" or having the print job pass on in to oblivion, not giving an error on the printer or computer.
    Now, the LW Pro 630 supports LaserJet IIP emulation... So I manually configured the driver to a LaserJet IIP in XP, set the push button to 3, and it prints! Only problem is, the pages look like they were sent through a bad fax machine.
    I uploaded the scan of the XP Printer Test page here (http://img221.imageshack.us/my.php?image=lwpro630xp2cq7.jpg). Obviously the printer works, but I'd rather not print reports and whatnot on it when it looks like this.
    For reference, here's the scan of the printer spec sheet that prints when the push button's set to 4 (http://img221.imageshack.us/my.php?image=lwpro630specsdy0.jpg).
    Does anyone have an idea how I can resolve the LaserWriter's identity crisis and make it print cleanly again? Thanks!

    The LaserWriter Pro 630 is a Postscript level 2 printer with LocalTalk, serial, Ethernet, and parallel interfaces.
    To use it with your Mac, you may need to convert its 14-pin AAUI Ethernet port (marked with <_> Icon) to an RJ45 Ethernet port by adding a used US$5 transceiver.
    It can then be used with the standard Apple LaserWriter driver when you turn on AppleTalk on your Ethernet port. No additional print server is required to use with a Mac.
    The overall smudginess is caused by shipping it with the cartridge in place, with the tape seal removed. The toner has flown all over the inside of the cartridge. You need a new cartridge.
    The LaserWriter test page is trying to explain the settings of the number dial in the center oval of the printout. It lists the ports in order and the settings imposed by each switch setting:
    8 -- for the MiniDIN-8 port, used for LocalTalk
    RS-232 -- for the RS-232 port, probably a DB-25, and shows the serial settings, like 9600, 8 data, etc.
    Ethernet -- for the AAUI Ethernet port, which accepts Postscript level 2 data using "EtherTalk" -- AppleTalk-over-Ethernet
    parallel -- for Centronics parallel, which will likely only provide HP PCL 4+ emulation and not Postscript.

  • Power Mac G5 and a Laserwriter Pro 630 - Is it Possible?

    Another question as I look to upgrade my father's computing setup.
    He probably wants to keep his older LaserWriter Pro 630. I'm going to load OS X Panther and Classic 9.2.2 onto the Power Mac G5. Is it possible to get the LaserWriter to print on a straight ethernet connection? Or do I need to devise another method to make it work. Also what's the scoop on drivers, AppleTalk, etc? Thanks very much.

    112491- LaserWriter Pro 630: Technical Specifications
    The laserWriter Pro 630 is a Postscript level 2 printer with an Ethernet port. It does NOT support LPR/LPD, so it must be addressed using AppleTalk-over-Ethernet. No adapter is required unless you intend to use a pre-Ethernet Mac. The printer is supported with the drivers built in to Macs running 8, 9, and all versions of X using a universal LaserWriter Driver and a descriptor file for that specific printer.
    On the Mac, you must turn on AppleTalk on the Ethernet interface you are using. Some third-party Wireless Base Stations refuse to pass AppleTalk packets, so if you need a new Wireless Base Station, use Apple or stick to the major brands.
    Message was edited by: Grant Bennet-Alder

  • Laserwriter Pro 630, Mountain Lion, and Macbook Pro

    Hi,
    I have a very old Laserwriter Pro 630 that I use for simple inexpensive proofing. On my old system (G4 Tower w/Leopard), it was connected via an ethernet hub.
    I'm now the proud owner of a Macbook Pro Retina (with no ethernet port), and I can't figure out how (or if) I can use this printer. Can someone give me some advice on this?
    Thanks,
    Mark

    There are certainly potential obstacles, but the "lowest common denominator" approach of a parallel to Ethernet (or wireless) solution works for me. If using a print server, the goal is to create an IP address where this printer will reside on the network. Since the LW Pro 630 is a PostScript printer, the rest is easy.
    To summarize the results of the thread you linked, including the links within it, regarding this specific model LaserWriter, based on my own testing on OS X versions from Jaguar through Mountain Lion:
    IOGear GUC1284B parallel to USB adapter attached to a Mac's USB port: works
    The same IOGear adapter connected to an AirPort Extreme or Express USB port does not work with the LaserWriter Pro 630, though it works with other parallel printers. I was never able to determine the reason but am pretty confident I exhausted every possibility. Read my responses to Loroi near the end of this thread: USB to Parallel Cable for LW Select 360?
    D-Link DP-311P and D-Link DP-G301 parallel to wireless adapters: both work. Similar parallel to wireless or Ethernet adapters ought to work as well.
    Another possibility would be to use a USB to serial converter, such as the Keyspan (Tripp Lite) USA-28XG. I have not attempted this potential solution. The challenge would be to discover the LaserWriter's default serial port settings, but a good guess would be 9600-n-8-1.
    Configuring the Mac to use this alternative would require no small amount of tedium with which you are well familiar I suspect the LaserWriter used a configuration utility that requires OS 9 and AppleTalk to configure its serial port, and may also have been required for the AAUI transceiver which the OP probably doesn't have. The fact this particular LaserWriter has a parallel port that requires no configuration makes this an unattractive alternative.
    The disadvantage of any of the above solutions is that complete, bidirectional communication won't work, meaning the printer will not be able to inform the Mac that it's out of paper for example. If the printer is not ready the print job will patiently wait until it becomes ready. Communicating with the printer to determine details such as page count are also unavailable without Intel-coded utility software that does not exist in OS X.

  • Change name of LaserWriter Pro 630

    I've got a LaserWriter Pro 630 connected via ethernet. I can print fine from my 10.4 box, but I've got 2 issues with it:
    1. The printer's name is a leftover from the previous owner. How can I change it? I know how to change the displayed printer name on my Mac, I want to change the stored name on the printer.
    2. How can I get the printer to stop printing a "ready" page every time I turn it on?
    No, I don't have access to Classic or any OS 9 machines.
    Thanks.
    -Pete

    I have a DP1.8 with 10.4.6 and don't have a problem opening "Apple Printer Utility" in a window, which is what is needed to accomplish the 2 items that you mentioned. I too thought that I didn't have classic for a long time as well, or that it was unstable to use. I realize that I can't boot from classic but "Apple Printer Utility" does open in a window and I don't remember installing classic.

  • Laserwriter Pro 630, USB to Parallel, Original Airport Extreme-- in 10.6.4

    *If you have used a USB to Parallel adapter to place a pre-LPD/IP Laserwriter on your Snow Leopard machine, I'm looking for your input!*
    I have a Laserwriter Pro 630 -- no more AppleTalk in Snow Leopard. I'd like to attach it through my Airport Extreme's USB printer port.
    It seems that:
    - Some people have had success with USB to Parallel cables
    - Some have been able to do this without additional software
    - Maybe the cable is the issue
    - Maybe it won't be possible
    I read several sources that explained you can use a USB to Parallel cable to bring up the printer in Snow Leopard. I bought such a cable. In the *Add Printer* dialog, it could see the cable, but would not allow me to Add the printer.
    I found a thread (http://discussions.apple.com/thread.jspa?messageID=12060195#12060195) that referenced what I was seeing, and the USBTB back-end. After installing that, I was able to print (though when I changed the name of the printer queue, it didn't work -- I had to add the printer again). Further, if Airport Utility, under Printers, it doesn't see the USB cable or the printer at all.
    I read an 11 page thread (http://discussions.apple.com/thread.jspa?threadID=2073321&tstart=0) which referenced a handful of people using a USB cable, though several of them seemed to be able to do this without USBTB. It strikes me that if my printer (cable) required the addition of USBTB to the Mac, it might be that the Airport wouldn't be able to see it without that same backend.
    So I'm left wondering:
    - should I get a different cable?
    - should I install something else besides USBTB?
    - is it even possible to connect the LW Pro 630 to the Aiport Extreme over the USB to Parallel adapter?
    Thoughts, experiences... Sought!

    You should get a parallel print server and not use USB.
    Why do you say that? Many people report success using USB to parallel, and while there may be advantages of using a print server, there seems to be several disadvantages:
    1- another power-consuming device I have to plug in and either run all the time or turn on when I turn on the printer
    2- more cables and connections and configurations
    3- more expensive
    I should probably note, too, that I re-read the 11 page thread and went ahead and bought the one cable mentioned there (iogear's). It works fine, selecting the 630's PPD. It won't be recognized by the Airport Exteme.
    Oh well. Waking the Mac so I can print from the MacBook is pretty trivial, since to turn the printer on, I have to go to the same room the Mac is in.

  • LaserWriter Pro 630

    I have a LaserWriter Pro 630 which will not now work with OS 10.6 because Apple Talk is no longer supported. Here are the connections I have been using: An Asante FriendlyNet adapter is plugged into the printer's D-connector LAN port. From there, an Ethernet cable goes to my Airport Extreme's RJ45 LAN port.
    Does anyone know if there is a way to get this printer working with 10.6? The LaserWriter Pro 630 is a slug, but it works and is paid for.
    Thanks!

    See Mac OS X v10.6- Mac 101 - Printing.
    AppleTalk is no longer supported in Snow, so as the other poster suggested you would have to share the printer from a system that supports AppleTalk.

  • Wallstreet, OS X and LaserWriter Pro 630

    I've got a WallStreet G3 PowerBook running OS 10.1 and a LaserWriter Pro 630.
    the laserWriter worked great with AppleTalk, LocalTalk Boxes on the Wallstreet when it was on OS 9.
    It works great on with the Built in Ethernet on a G3 iBook 500 running OS 10.1 and a G4 iBook running OS 10.4
    But I can't get it to run on the WallStreet with OS 10.anything.
    Any help here would really be appreciated.

    I don't know if this will help but I'm useing a HP 5110. Instead of hooking the printer to my network, I have it USB into the most used computer on my network. I then make sure that the folowing System Preferences are met on the Master computer.
    That under Print & Fax the box next to share my printer with other computers is checked.
    Under Sharing then Services that the box next to Printer Sharing is checked,
    and then under Firewall the box next to Printer Sharing is checked.
    If all of these are met I think it should work.
    PowerMac G4 Dual Quicksiver 1.46 GHz   Mac OS X (10.3.9)   iMac 233 and PowerBook G3 Wallstreet

  • LaserWriter Pro 630 : flashing 'Ready' light?

    Howdy, all!
    My LaserWriter Pro 630 just started 'acting up' recently and I was wondering if anyone has seen these symptoms before...
    The 630 is attached to my home network--there haven't been any changes to the network in the past 8-12 months.
    I can send a document to the printer from my PowerBook G4 (which is connected to the network through an Airport Base Station).
    The printer 'fires up,' as if it's getting ready to do some printing. Then, it spits out a blank sheet of paper--completely blank.
    The 'Ready' light continues flashing, even though the print queue is empty.
    I have pushed the Service Test Page Button, and the 630 successfully printed the page o' lines.
    I took the printer this afternoon to a laser printer guy, and he replaced the Laser/Scanner Assembly. Unfortunately, it hasn't remedied the situation.
    I've also got a brand new toner cartridge in the printer. I initially thought that the printer was simply out of toner, but I guess I was wrong.
    Anyone have any clues, hints, or words of encouragement?
    Thanks in advance,
    mg

    HMMM - tried it with the Appletalk connection - or even the parallel port on a PC?
    Tried your Mac with another printer (even a USB printer) - Could show some problem
    Can any other computer hit the printer?
    Just some thngs to check out -- hope this helps

  • LaserWriter Pro 630 two solid orange lights won't turn green.  Put in new toner and test page does print.  Any ideas?

    LaserWriter Pro 630 two solid orange lights won't turn green.  Put in new toner and test page does print.  Any ideas?
    The warmup stage does not seem to go all the way through its normal startup noises and the printer does not get hot.
    Thanks for any help.
    Steve

    See if this link has some useful info:
    LaserWriter Pro 600/630

  • Linksys Router + iBook + PC = Need Security set up!

    Hello
    I have a G3 iBook running 10.3.9 (wireless) and a Linksys router.
    I now also have PC laptop running Windows XP Home edition (wireless).
    I have been able to set up the Mac and PC both to work with the router, however, I need to set up security! There are several security options on the Linksys Admin site, and I'm not sure which is best, and will work for these two different worlds. Any help or articles on what to use and How to set it up??
    Thanks,
    Bonnie
    iBook Mac OS X (10.3.9)

    Point your browser to the next default address:
    http://192.168.1.1
    The default password is "admin", and no user should be entered.
    There you can change the network settings of your wireless network (and wired too). I suggest you use WPA.
    Here are more detailed indications.
    iBook G4 12, 1.33 GHz, 60 GB HD, 1 GB RAM, BT, Zire 72, 2 iPods Mini   Mac OS X (10.4.8)   . "Nacer es comenzar a morir" Théophile Gautier

  • Why dont the Mac Pro's with Retina Displays have a CD/DVD drive?

    Why dont the Mac Pro's with Retina Displays have a CD/DVD drive? Will Apple eventually stop producing CD/DVD drives?

    Gethin R wrote:
    Why dont the Mac Pro's with Retina Displays have a CD/DVD drive?
    Because Apple did not put one in there.
    Will Apple eventually stop producing CD/DVD drives?
    We can't really answer that, but it would not surprise me. More and more of the computers being produced by Apple lack an internal optical drive. If you really need one, get an external such as LowLuster suggests.
    Best of luck.

  • Why my  IPAD2  sometimes loose connection with my router and I need to enter again the WPA password?

    Why when my IPAD2 loose connection with the router sometime I need to enter again WPA2 password?

    same problem here.
    MBA (latest os), even my ip5 (latest ios) & ipm (also latest ios) looses the connecntion.
    Ive tried to figure out what causes the problem - neither my xbox360 nor (and i guessed they will be the problem) the pcs here...
    the connecntion runs well.. switching also (MBA-IP5-IPM).. but not for longer than an hour.. or even minutes. When the connection looses a high-frequency noise is followed by silence. A restart fix that problem and all devices streaming well... but not for long...
    any suggestions?

  • Laserwriter Pro 630 printing out as a negative WHY

    I have had a LWP 630 for 4 years with out any major problems. It is networked for 2 PC computers and is the default printer of 2 printers. I have a Netgear print server. My OS is Win XP. The other day after printing several docs, it started printing in the negative. in other words black and white are reversed. All the printable area is black and any characters are white. This is from either PC over the network. This is from either PC from the LPT1 port to the centronics port, on the printer. (without the print server) It prints whatever it's sent. What can be done to switch it back???

    I also have this issue. I just had a Pro 630 go belly up with a Green solid and Toner Solid and Paper Out solid. Diagnostics would NOT run. Printer just stopped responding and printing. It would however print a perfect test page with button push near exit tray.
    Got a used printer from Craigslist and swapped out the I/O board. Now, it only prints in Negative and in really big type. If I only have 8MB ram, it prints a blank page. I am guessing it is printing just fine, but white text.
    If I add 16 or 32 MB from the other I/O board, the background is gray or dark gray respectively and the type is really big.
    Cannot find anything that will reset this thing.
    Also, any leads on where I can get a copy of the latest LaserWriter Utility so I can run it on a Mac OS 8.6 machine?
    Mike

  • Trying to set up Time Capsule for WiFi access with Linksys router

    Problem: I must use a Linksys router to connect to internet, since I have my telephone connected to this router (Vonage). I have set up a Time Capsule and connected it to the Linksys router, which is NOT wireless. I would like to use the wireless capability of the Time Capsule to provide wifi connection for laptop computers. The Time Capsule's wireless network is visible to these computers, but they do not connect to the network, since the Time Capsule is not the source of dynamic IP addresses; rather, the Linksys router is the source for IP addresses on my network. What must I do to get IP addresses supplied to computers attached via wifi?

    The Time Capsule was set up using bridge mode. My initial error was to use the WAN port. After switching to a LAN port to connect with the Linksys router, the laptop computer was able to connect to the network wirelessly, but it could not obtain web page from the internet.
    The laptop is a Dell Inspiron 6000; with an ethernet cable attached to the Time Capsule, it receives an IP address AND it can obtain web pages from the internet. The command "ipconfig /all" issued at the DOS prompt yields approximately the following:
    Broadcom... (this is the ethernet card) ... IP address 192.168.15.104, with the gateway 192.168.15.1 (which is the Linksys router)
    Intel(R) PRO/Wireless... (this is the wireless card) ... IP address 192.168.15.103, with the same gateway.
    I can ping the iMac from the Dell laptop; the iMac is connected directly to the Linksys router. Running ping 192.168.15.104 from Terminal on the iMac succeeds, while ping 192.168.15.103 does not.

Maybe you are looking for