Latest FirePro cards not supported in first 16x slot on S20
I have a few of the new Firepro cards (specifically the W5000 and the W7000) and I am finding that neither of them will work when they are placed in the first 16x slot of my S20. If I place them in the second 16x slot, then it will work. This is not good as I want to run two cards. I currently am running a Geforce GTX 480 in the first slot and it is behaving as expected.
Is there a specific vbios that is required for this to be recognized in the first slot.
Note that the LED light on the back of the card is red and I am getting the video not found post beeps. I am also on the latest system bios.
Thanks
Just to be clear, mixing NV and AMD cards is a bad idea. I think you're trying to get a config working with multiple Firepro cards, but it wasn't totally clear.
Taking the GeForce card out of the equation, the Firepro cards in question aren't officially supported. From a power perspective, the W7000 is 150W TDP (or lower) and the W5000 is bus powered. So dual W7000 shouldn't be an issue there.
My guess is you're running into BIOS issues, and probably more specifically OPROM issues. It could be a space problem, so disabling features such as second LAN and PXE boot (if they are not used) is an option. But given that we've done no official qual work on those cards, it's hard to say what the exact problem is.
Also note that the first x16 slot on the bus that gets detected by BIOS is the "lower" x16 slot...so your "primary" card should go there.
I'll finish by my standard canned response of:
The W5000/W70000 is not officially supported
NV GeForce cards are not officially supported
Mixing of the two above cards are definintely not supported
Similar Messages
-
I phone blocked! Sim card not supported!
I phone blocked! Sim card not supported!
Recently bought an Iphone here in the Republic of Congo for about $600 and it was working fine until an update on Itunes. Now the phone just shows a USB cable and I tunes logo. When I connect the phone to Itunes it wants to restore and update, but then just blocks the phone again.Who did you by the phone from? Apple? A telecom company? Ebay?
The phone was most likely jailbroken and unlocked. Applying the latest firmware updated undid that.
A -
I need to download a eariler version of firefox because the latest version is not supported by my financial institutions or colleges im attending, every time i look for 3.6 im redircted to the 4.0 download
http://www.mozilla.com/en-US/firefox/all-older.html
-
Sim card not supported after unlock iphone 5c
iphone 5c, 12.7 GB, version 8.1.1, after unlocking when i connect it to itunes w/ other sim, sim card not supported error registered,. i check it to IMEI and its unlock, but why icant use it? I try to restore to itunes and erase my iphone nothing works, what can i do?
How was the phone unlocked? Was it unlocked by your previous carrier? The only way to unlock your phone is to have your previous carrier unlock it for you.
If you phone was unlocked in any other way, this constitutes hacking or jailbreaking and your phone will not work with another sim card.
Get the phone unlocked properly by your carrier and there is no reason why it should not work. -
i installed new 6.0.1 os it is done succesfully but after that insterted my sim it is showing sim card not supported any one plz help me
That message occurs when updating a phone that was hacked to be used with your network. Upgrading the phone has re-locked it to it's rightful carrier. You will need a SIM from the original carrier to proceed.
-
1st think my billing info is not support debit card not support by apple 2nd think is my old I'd is not working even free app in app store......
1st think my billing info is not support debit card not support by apple 2nd think is my old I'd is not working even free app in app store......
-
VWIC is showing as "WIC module not supported/disabled in this slot"
Hello All,
please help me on this asap!!
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
HWIC Slot 0 0x00200000
PVDM 0 0x00200000
Onboard devices &
buffer pools 0x0228F000
TOTAL: 0x0268F000
Rounded IOMEM up to: 40Mb.
Using 7 percent iomem. [40Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 22-Mar-10 02:13 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2901/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FGL162722DK
2 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
Press RETURN to get started!
*Mar 1 00:00:04.931: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = ipbasek9 and License = ipbasek9
*Mar 1 00:00:05.019: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = uck9 and License = uck9
*Jan 23 07:37:07.403: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Jan 23 07:37:15.119: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/0 has an unknown id 0x6EF
*Jan 23 07:37:18.679: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Jan 23 07:37:18.679: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to reset
*Jan 23 07:37:18.679: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to reset
*Jan 23 07:37:19.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Jan 23 07:37:19.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
*Jan 23 07:37:20.823: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Jan 23 07:37:20.823: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
*Jan 23 07:37:21.063: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 23 07:37:23.083: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
*Jan 23 07:37:23.755: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 22-Mar-10 02:13 by prod_rel_team
*Jan 23 07:37:23.759: %SNMP-5-COLDSTART: SNMP agent on host Hewitt_Noida is undergoing a cold start
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to up
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 3 in slot 0, changed state to up
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 2 in slot 0, changed state to up
Hewitt_Noida>
Hewitt_Noida>
Hewitt_Noida>
Hewitt_Noida>en
Hewitt_Noida#
Hewitt_Noida#
Hewitt_Noida#sh diag
Slot 0:
C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:00:56 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC1624697D
Hardware Revision : 1.0
Part Number : 73-11834-08
Top Assy. Part Number : 800-30795-06
Board Revision : A0
Deviation Number : 123694
Fab Version : 03
Product (FRU) Number : CISCO2901/K9
Version Identifier : V06
CLEI Code : CMMJA00ARA
Processor type : C1
Chassis Serial Number : FGL162722DK
Chassis MAC Address : d48c.b51a.b668
MAC Address block size : 72
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 36 32 34 36 39 37 44 40
0x10: 06 17 41 01 00 82 49 2E 3A 08 C0 46 03 20 00 78
0x20: 4B 06 42 41 30 88 00 01 E3 2E 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 30 31 2F 4B 39 89 56 30 36 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 4A 41 30 30 41 52
0x50: 41 09 C1 C2 8B 46 47 4C 31 36 32 37 32 32 44 4B
0x60: C3 06 D4 8C B5 1A B6 68 43 00 48 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 65 40 01 25 41 00 87 42 00
0x80: 00 F8 00 28 03 E8 1C 89 07 D0 20 21 0B B8 20 93
0x90: 0F A0 21 2F 13 88 21 83 17 70 21 A8 1B 58 21 B0
0xA0: 1F 40 21 AB 23 28 21 79 27 10 21 78 41 01 1D 42
0xB0: 00 00 F8 00 28 03 E8 1C 20 07 D0 1F 40 0B B8 20
0xC0: 6C 0F A0 21 34 13 88 21 34 17 70 21 98 1B 58 21
0xD0: 98 1F 40 21 98 23 28 21 34 27 10 21 34 FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 0:
128-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11810-03
Board Revision : C0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC1602145Q
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-128
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 DC 41 01 00 82 49 2E 22 03 42 43 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 30 32
0x20: 31 34 35 51 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 31 32 38 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 1.0
Top Assy. Part Number : 800-34658-01
Part Number : 73-13420-01
Board Revision : B0
Deviation Number : 124402
Fab Version : 05
PCB Serial Number : FOC16100L9C
Version Identifier : V01
Product (FRU) Number : VWIC3-2MFT-T1/E1
CLEI Code : COUIA7NCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 EF 41 01 00 C0 46 03 20 00 87 62 01
0x10: 82 49 34 6C 01 42 42 30 88 00 01 E5 F2 02 05 C1
0x20: 8B 46 4F 43 31 36 31 30 30 4C 39 43 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 32 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 4E 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Hewitt_Noida#Hi Akshay,
As per
http://www.cisco.com/en/US/partner/prod/collateral/routers/ps5855/data_sheet_c36-609138.html
VWIC3-1MFT-T1/E1 is supported since 15.1(1)T1 and later.
Make sure you have this minimum IOS.
HTH
Manish -
Hi, i forgot my passcode for my iphone 4 and restored the phone to factory settings and it updated itself to ios5, but now the phone says that the sim card is not supported. what should i do? I've tried with other sim cards and got the same error. Now the phone cannot be activated
Ok, here we go with a solution from the Official Apple Website. Test it after each step.
Reseat the SIM card: Remove the SIM card in your iPhone and then reinsert it.
Restore your iPhone. Note that the computer you are using to restore the iPhone needs to be connected to the Internet. You can verify the connection by loading the first page of the iTunes Store.
Contact your carrier to verify that the unlock was applied in their system. -
SIM Card Not Supported. Never Hacked iPhone Bought From Apple Store!
My 3GS was stolen yesterday. I have my never hacked iPhone 2G that I wanted to re-activate so I went down to the ATT store and they gave me a new sim to put in and activate. iTunes says that the SIM is not supported. Went back and tried another SIM and no luck. After 2 hours at the store still no working phone.
I never hacked the phone, just always updated it with the latest apple software. It sat in a drawer for a year now until my 3GS was stolen. Restore didn't help.
ANY IDEAS?Mmmm...the sim you're trying to use is activated, correct? If so, try this:
See if you can force the phone into recovery mode:
Leave the USB cable connected to your computer, but NOT your phone, itunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new. You, of course, would chose "new". -
SIM card not supported after upgrade OS
I bought iPhone in Hongkong & use it in Jakarta. Originally iPhone worked well with SIM card of Telkomsel/XL, but few days ago I downloaded & installed upgraded OS ver 1.1.4.7 from internet and the result is my iPhone cannot work since the SIM Card is not supported anymore. pls help me resolve this.
DjendAll the iPhones sold in Hong Kong are hacked. Once you done the Restore, it would loss the unlock SIM function.
Hope the iPhones can officically launched early in Asia.
Message was edited by: Mitch 751 -
3GS iOS4.1 new sim card not supported
Hi guys, I own a PAYG iPhone that was bought direct from apple. I have been using it on O2 for the last year but I have just signed up for a Vodafone contract. I received my new sim card and put it in, it now goes to the emergancy calls pages and itunes says that the sim card is not supported.
The phone has never been jailbroken or anything in anyway. I have tried restoring the phone and this has made no difference.
Tried the sim in another phone and it worked fine.
Any ideas?Doesn't sound like it.
I would contact O2 to determine if your pay-as-you-go iPhone that was used with O2 over the last year is carrier locked with O2. If the iPhone is carrier locked with O2, it will be up to O2 to unlock the iPhone.
If you specially requested an unlocked iPhone when purchased from the Apple store which is the most expensive, you need to contact the Apple store. -
SIM card not supported for the 2nd time
My initial iphone 4 was broken beyond repair, under warranty I forked out the cash to receive a replacement. A replacement which told me my sim was not supported - receiving a replacement micro SIM from my carrier it STILL DID NOT WORK. I sent my replacement away, and received a replacement for my replacement. SIM card still not supported. SIM works fine with any other iphone 4, i've tested it on several other computers and completed full restore. Is it just me or does Apple seem to be trolling me?
I bought an iphone from o2 yesterday and got the micro sim activated today, inserted it and itunes says the sim carrier is not supported :S yet the phone is from o2 and so is the sim! And the sim works fine in a normal o2 phone when inserted with the bigger tray.
I have taken it out and put it in again but no luck! I rang o2 and they said they are sending me a replacement micro sim but i have read about the problem being in the phone (well at least it was in the 3gs)!
I'm so gutted - owned an iphone for 24 hours without using it think im going to o2 and then the apple shop tomorrow! Not at all happy... -
I bought iphone 3gs. Restored successful, but says your phone not support this sim card. Contact your carrier get supporting sim card. I have att simcard. I restored other iphones with no problem.
Have you gone to AT&T to get a replacement SIM card?
-
Graphics card not supported?
I have a 2008 Mac Pro, 8 core, 2.8GHz system. It has the ATI Radeon 2600 video card, with 256MB of GDDR3 RAM. I want to purchase and play the upcoming Bioshock 2 game, but it says that my card is not supported, but I am curious if the game will still play, but maybe at lower settings, or lower frame rate. My question is does "not supported" mean that it will not run at all?
JaredThanks,
Sounds like I need a better card, or forget about this game.
Jared -
Graphics card not supported - GMA X3100
I've replaced a Macbook 2.0GHz from 2006 with 64MB shared video memory with a brand new 2.2 GHz with 144MB shared video memory. But when I start MainStage, I get the message that my graphics card is not supported.
Any idea why is that?
I haven't done any updates. Would that do it?
Thanks.Thanks Blueberry
Maybe you are looking for
-
HP Pavilion P7-1141 will not shut down... Any thoughts?
Brand new HP Pavilion P7-1141 desktop (AMD A8-3800 quad-core CPU, 8GB RAM, 1TB HDD, Radeon HD 6550D, Windows 7 64-bit) will not shut down properly regardless of what I do - I can press on/off button on the desktop, or choose "shut down" from Windows
-
Hey, I wanted to know how to move the photos on my camera roll to other albums to organize them. I am using Windows, so IPhoto is not an option for me. Is there a way to do this...or am I stuck and just going to have a gross amount of photos in the C
-
Web service call "getAllServiceNames"
var oListURL = "http://localhost:3612/WebSite18/Service.asmx?WSDL"; var e; try xfa.host.messageBox("starting List Retrieval."); var service = SOAP.connect(oListURL); if (typeof service != "object") xfa.host.messageBox("Couldn't get List object."); if
-
HI experts I would like to show the positve values with + sign in BEx ANALYZER adn WAD also . Is the any option for this. Regards Ranganath Edited by: Ranganath on Jun 30, 2011 1:03 PM
-
Dear experts, I have used functionmodule as RFCs to fetch data from SAP using java/jco.Here i realised that all work has to be done in sap itself.Java is just a platform to fetch that object and show me the data. However i wish to know can i use nati