Latest firmware update killed my network, HELP!

so.. I updated the firmware about a month ago when it was first available.. My device is completely stock and i'm not really ready to root nor factory reset it. I reset it before due to an error on the backup assistant screwing with my external sd card (the real issue was the copy and paste error some devices were faced with). I've been through about 4, 32gb externals and the latest sandisk just sent me.. is bad too. :/
But, that's not the issue i'm getting at. Since the lastest firmware update with caller ID, etc.. I've had little to no signal, dropped messages in my house, completely dropped 4G LTE while using GPS.. horrible due to some areas I was in.. slow or lagged device to the point where i've had to restart my device 3-4 times each day in the last week...
Can someone either tell me if there is a quick solution to this or what the next step should be in this process. because this whole "we've retracted the update but are looking into a fix" ** isn't very settling. Since, on Verizon's time.. I'm afraid the next update won't come for a few months..

I am having the same issues described by everyone else (dropped 4G, worse signal, etc.) after the update to MD3.
My wife's phone is identical but without the update and it works fine (like mine did before the update)
WHAT is the resolution to this issue, Verizon? I really don't believe I should have to go down the root-my-phone route and find third party sources to fix this issue. Why can't you just push the old firmware back to my phone?
I am quite disappointed that what was my best smartphone experience to date has been ruined.

Similar Messages

Has latest firmware update killed y TC?

Hi all,
I have recently purchased a Time Capsule to back up y MacBook Pro and my iMac. All worked well after a bit of trouble with initial set up, but then a few days ago I got a message telling me to run a firmware update for the TC. Since running that I have been unable to get it back on line. I have reset it a number of times but still my machines do not pick it up when running the set-up through the Airport Utility.
Can anyone help?
Thanks
Frank

Well I did the very same upgrade and now the airport utility cannot find the time capsule ? What a pain in the *** is apple aware of this? How can I get Airport Utility to 'not' scan so I can manually reset the firmware on the time capsule ? It took days to back up my G5 and iBook and in the end ethernet was the only way. Anyone know how to fix this mess ?

Internet stopped working on MBA after latest firmware update. Help please!!!

Internet stopped working after installing the latest firmware update. WiFi still connects to router, our other mac desktop still connects to internet as usual (same network). I can't even re-install the MBA OS since it needs an internet connection!!!
Any ideas?

FIXED.
I swapped our wireless router for a newer one, internet seems to work fine again (we were sent a new one by our internet provider which we never set up until now).

Zen Touch latest Firmware Update...player not connec

I tried installing the latest Firmware update for my Zen Touch (released 2-09).
The player is connected and recognized by Windows and the Media Explorer. However, when I try to install the new Firmware it keeps saying "player not connected".
I tried d/l two different language packages cause I wasn't sure what counted - player language or operating system langauge. Anyway, that didn't make a difference.
So what do I do? I have no idea where to start. It's firmware for the correct device connected through Windows XP.
I have made a firmware update before, which worked fine. After that I updated the media explorer software.
Help is very much appreciated! Thank you in advance.
-tina-Message Edited by tinas on 2-0-2005 08:56 PMMessage Edited by tinas on 2-0-2005 09:00 PM

Perhaps it's worth making sure no software is using the player, so reboot the PC, and turn off the Creative Detector. Then try again.
Are you trying to upgrade to the .0.03 version?

Mid 2006 iMac Boot Problem (Since latest firmware update)

I have a Mid 2006 17" iMac. Ever since the latest firmware update in early December, about every other startup I've been having boot problems. After the white screen with the Apple Logo and the spinning wheel it goes to a blue screen like normal, but instead of the 'Loading Mac OS X' white window popping up it stays blue and the spinning loading wheel starts. I've left it loading for quite a while before and nothing changes. I have to do a force shut off by holding the power button. and then I start it up and it will boot normally.
Any help would be appreciated.
Thanks!

Actually, I think it'san early 2006.

HT3728 Does factory reset go back to latest firmware update.

I have resently updated my airport express to latest firmware. The airport express is configured as an extension to my wifi with an Extreme as main device.
Shortly after the firmware update (1-2 days) the express stopped working and status light turned yellow.
I have since then tried to do factory reset several times without getting the device up and running again.
When doing factory reset the status light turns yellow after releasing the button and stays amber with short interval with green (1 second every minute or so)
I have not been able to discover the express from my iPad, iPone or iMac again.
Could the reaons be latest firmware update?
Any advice to get it back to normal?
Thanks,
Per

Does factory reset go back to the latest firmware update.
A Factory Default Reset will not affect the installed firmware.
Shortly after the firmware update (1-2 days) the express stopped working and status light turned yellow.
A solid amber light is unfortunately an indication that the internal power supply inside the AirPort Express is failing, or has failed.
I have since then tried to do factory reset several times without getting the device up and running again.
The AirPort Express has failed, and will need to be replaced.
When doing factory reset the status light turns yellow after releasing the button and stays amber with short interval with green (1 second every minute or so)
This is yet another confirmation that the Express has failed, and will need to be replaced.

Attempted Iphone 4 update to latest firmware update "failed"

Ive attempted to update the Iphone to the latest firmware update and it has failed 3 times, the final time it looked as though
it worked but stopped and went into new mode to go-back to Restore to old setting. Now it is locked up and asking me for the admin backup password
and everything I've tried is not working.. Not sure what to do at this point.
The laptop I'm using is a Panasonic CF29 and running Windows XP with SP3 installed.
I'm open to any ideas at this point.
Thanks Artman

Then it's pretty hopeless. Normally the error message remains displayed until you click "OK", so it's surprising that you didn't see it. You can try the shotgun approach; just try a bunch of stuff in the hopes that it will work. But first I suggest trying to update it again, and this time watch it. The following list covers the most common causes of update failures:
Open a Command window and type the command "netsh winsock reset"
Reboot your computer
Disable your antivirus and firewall
Launch iTunes
Connect the phone using a USB port directly on the computer, not a hub
When the phone is recognized in iTunes click on it, then click Restore
If the phone is NOT recognized in iTunes, disconnect it, the hold the HOME and SLEEP buttons for exactly 10 seconds until the screen goes black, then release SLEEP but continue holding HOME while you connect the cable and continue holding HOME until iTunes recognizes a phone in recovery mode
If the update completes you are in business
You mentioned being prompted for a backup password. If your backup is encrypted you will need to know the password to complete the restore; if you don't know it you will have to restore as New and manually add your content back. If it is encrypted you really did enter a password for it once, whether you remember doing so or not.

Can't send mail after latest firmware update

My outgoing mail won't go out after the latest firmware update. I have 4 different accounts and none are working. Tried in various locations. Any ideas would be appreciated. Thanks

Was this for 10.5.8???
Others have reported it for 10.6.8 & up...
http://x704.net/bbs/viewtopic.php?f=12&t=6118

Latest Apple TV Kills entire network connection

I was super excited to purchase my first Apple TV, until I hooked it up. I have found if I use it wirelessly, it will kill my entire network within a short amount of time. 10-15mins. After that time, no computer can access anything on the internet, and the Apple TV will not find the library again after I finish watching whatever was playing. But, everything runs smoothly until that point. It finds the library, internet access through ATV is fine, remote app on my iPhone works fine, it's beautiful! …for a short time.
Through troubleshooting that issue, I found if I connect via ethernet, it will not find my iTunes library at all, but it will connect to the internet just fine. ????
I've found a few random things on the web related to this, but they are all in reference to old ATV models, and I cannot seem to come across any posts mentioning my exact problem. So far, I've tried doing the following on both wired and wireless connections:
-made sure my Linksys router has the latest firmware version available
-tried increasing the client lease times on the router to roughly 1 week.
-tried manually configuring the ATV IP to maintain a static address, but it still kills the entire network when running wireless, and will not find the library when wired in.
I've never had problems with my network before; it's been running smoothly for 5 years. I've also been streaming Netflix to my LG Tv for about a year now with no issues. I am totally happy to invest $99 in an ATV-love the concept, love the convenience. But if Apple has something going on where it will only work with an airport extreme, I am not happy with investing $278 in an apple tv when my current wireless setup works just fine. Does anyone have any ideas on what I may be doing wrong or how this can be resolved? I really do love the idea of having access to my media wirelessly, and would hate to have to return the ATV.
Tech details:
Latest little ATV model, library hosted on a mid 2011 MBPro Core i7 running OS 10.6.8 with latest iTunes version. My library has about 65gigs of music and about the same in movies. We have that MacBook and 1 PC runing on the network. I am using this Linksys router: http://homesupport.cisco.com/en-us/wireless/lbc/wrt54G
Many thanks in advance to anyone who can help!

Very similar situation here. My ATV3 is connected via WiFi, but it loses its network connection if the following two conditions are met: it sleeps, and my Aiport base station is turned off any time afer the ATV sleeps. When I power up the Airport again, the ATV does not find my network without either restarting or selecting the network manually from a list of nearby networks.
In other words, sleep is OK only if the network is never powered off.
-dan

TC issues after latest firmware update

Here is the skinny, my TC went through the normal firmware update a bit ago. Wednesday my Internet stopped working, when I use the Airport Utility app it showed the TC online, at first, then it gave me the error that the TC did not have a valid IP. Thought might have been a problem on my ISP's end so I grabbed another router and set it up Internet no problem. Has to be the new firmware right so I pushed the firmware back 3 versions, and still the same thing no valid IP but connected to the Internet but no HDD (Yes it said not a valid IP but connected to the Internet on one wireless PC). Everything else in the house would not connect to the TC they could see it but when you went to connect never asked for a password and I got the spindle of death type deal. I saved my settings and did a hard reset with the button on the back of the TC, started over and rebuilt the connection, same thing happened not a valid IP. I have read that Apple released 3 different firmware updates supposedly the last one works, it doesn't when I load the firmware I get the same error TC does not have a valid IP. I need some help, I have cycled through power down and power up situations over and over. Anyone have any other suggestions?

Need some more info.
What is the modem.. make and model?
Is it both modem and router or just a modem?
What is the actual model of the TC.. the number from the base.. A1xxx where the x are numbers.
The latest firmware is an issue.. that is 7.6.4 and you should go back to 7.6.1
But it does seem hard to get rid of properly.
I want you to do a factory reset not just a hard reset.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Please redo the setup using all SMB names.. that is short, no spaces and purely alphanumeric characters.
eg TCgenx (use actual gen if you want) for base station name.
TCwifi for wireless name. (or TC24ghz and TC5ghz which is well worth naming both bands so you can test more carefully).
Please download and install a v5 utility on a computer if any of them use up to Mountain Lion.
Tell us what OS the computers are running and I can tell you how to install the old airport utility.
Test the TC in bridge to your other router is also a good alternative.

Latest firmware update and startup problems

Hi I have been reading all about this so-called firmware and its importance in keeping updated on my new macbook pro. Therefore I have been diligently trying to keep it updated over my dial-up connection. I installed the latest firmware as my automatic update suggested. Now I get the spinning startup circle of death. Tried booting in safe mode to no avail. Help? (I also have version cue installed.)

Hi jbell,
Firmware updates are not availible in Software Update, only sofware updates are. Did you Repair Permissions prior to and after updating software? You always should. Go to Applications-Utilities-Disk Utility, and highlight Mac OS X in the left hand column, then Repair Permissions below. Firmware updates are available here....
http://www.apple.com/support/downloads/macbookproearly2006firmwareupdate101.html
http://www.apple.com/support/downloads/macbookpro15inchsmcfirmwareupdate.html

EFI Firmware update kills Airport

I just installed the EFI firmware update w/o trouble. However, upon reboot I noticed the airport was gone from the menu bar. I booted Safari and got "not connected."
I then opened the network sys pref's and when I try to connect I get "No Airport Hardware Found."
Under System Profiler I see "No info found" under the airport tab.
Any help? Thanks!

Called Applecare. Always polite and helpful. Found solution to this airport problem.Here are the steps:
Turn off your mac.
Take off your battery, disconnect the power cord.
Then press the power button for 5 seconds.
Replace battery and power cord and restart your mac.
Now airport should be back. Hope it helps as it helped me

Firmware updates kill ATT DSL

Every time I update the firmware on my AEBS, I end up not being able to get online with ATT DSL.
I end up in an infinite loop trying to configure the router (I just ask it to use the old settings) and resetting the Speedstream modem, then finally end up resetting and re-setting up everything with an older (pre-7.3) firmware version to get things working again.
ATT tries, but is not always able to help other than "shut down, unplug, turn off, restart" type advice. If I bypass the router, it works just fine.
Any suggestions out there?

Seems impossible for router to corrupt password. But still try to update to latest firmware to ruleout that possibility.

WAP4410N wireless traffic locks up even when running latest firmware update

I maintain multiple buildings, and each building has anywhere between 1 and 4 Cisco/Linksys WAP4410N access points. The problem is that at random intervals, the access points just stop sending and receiving wireless traffic. Every day or two, I have to log into every single access point (either via HTTPS or SSH) and reboot them in order for them to start working again.
In short, here are the config details:
They are all version 2 hardware (either WAP4410N-A V02 or WAP4410N-E V02).
They are running IPv4 (IPv6 is disabled) and get static IP addresses via DHCP.
When there are WAPs with overlapping signals, each WAP is on a different non-overlapping channel (1, 6, or 11).
Each WAP has two SSIDs (with spaces in their names). One is secured with WPA2. The other is unsecured.
There are two VLANs on the Ethernet interface. Each of the two SSIDs are assigned to a separate VLAN.
There is a DHCP server on the network, so the WAPs do not actually assign IP addresses to clients.
All of the WAPs are running on PoE switches. However, some are gigabit and some are 10/100 switches. Brands vary (Dell and Linksys) and models vary.
Cisco finally recognized this issue as:
CSCtx62203—In certain environments and traffic model, the WAP4410N may lockup after some undetermined time. Workaround: Reboot the device.
As such, the workaround didn’t really offer anything new. Rebooting every WAP ends up being a very time consuming process. It’s awful. And since you have no control over when this issue surfaces and can’t put any safeguards in place, I get calls about it at various points of the day almost every day.
Supposedly the most recent firmware update (2.0.6.1) claimed to fix the issue, but it only seemed to make it worse. So now instead of a WAP locking up every day or two, it locks up anywhere between every 15 minutes to 4 hours when in use.
The firmware was updated and the following issue was fixed in firmware version 2.0.6.1: CSCtx62203—In certain environments and traffic model, the WAP4410N may lockup after some undetermined time. (A protection mechanism was added to guard against sporadic problems with client association that could occur after six to 24 hours.)
As for troubleshooting, there are no error packets. On access points running firmware 2.0.6.1, these messages appear:
Feb 7 13:42:27 Syslogd start up
Feb 7 13:51:59 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 13:52:01 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 13:52:05 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 14:47:01 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 14:47:02 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 14:47:05 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 15:22:53 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 15:22:56 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 16:15:19 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 16:15:33 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 12:27:25 Syslogd start up
Feb 7 14:06:18 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 14:06:23 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 14:44:28 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 14:44:31 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 15:09:18 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 15:09:24 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 15:42:23 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 15:42:25 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 16:52:18 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 16:52:24 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 16:53:05 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 17:20:05 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 17:20:08 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 17:23:34 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 17:23:39 syslog: Found beacon stuck, down and up the VAP interface.
Feb 7 21:21:28 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 7 21:21:30 syslog: Found beacon stuck, down and up the VAP interface.
Feb 8 09:55:23 kernel: ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
Feb 8 09:55:29 syslog: Found beacon stuck, down and up the VAP interface.
These log messages appear on both WAP4410N-A V02 and WAP4410N-E V02 devices.
I noticed that when the “beacon stuck” message appears, wireless traffic locked up 10-15 minutes prior to the message’s appearance in the log, and the SSID drops for 4-6 minutes after the message appears.
Is there anything that can be done to address the issue?

1) LAN port speed doesn't appear to have any effect
2) Forcing a connection type doesn't seem to have any effect. This is also rather impractical.
3) I don't have that option (though there is a TKIP/AES mixed option). Either way, I'd rather not have to resort to using a weaker encryption method.
4) No effect.
I did manage to find some information about the error message (older versions of firmware didn't even offer that clue).
http://www.dd-wrt.com/wiki/index.php/Advanced_wireless_settings#Beacon_Interval
I ended up increasing the beacon interval from 100ms to 500ms under Wireless > Advanced Settings.
The wifi analyzer app on android seems to keep dropping the SSID when the beacon interval is set that high, so I might have to adjust it to find a good balance.
However, while it was set to 500ms, none of the access points went down for two days.
[edit]: I reduced the beacon interval incrementally down to 300ms. It started locking up at 250ms.

My macbook pro screen remains grey after latest firmware update

i just had the update notification for the latest firmware, proceeded to do so, and the screen remains grey, its been more than one hour and still grey, since its a firmware update i don't want to disturb it, but could it be that is taking so long?

Reboot it by pressing the power button down hard to force a shutdown.
If your still having problems, take it to Apple. I hope you have AppleCare becuase if they can't fix it, it's a new logicboard.

Latest firmware update killed my network, HELP!

Similar Messages

Maybe you are looking for