Latest OS X update & Bluetooth problems

After installing the latest software update on Tuesday, my bluetooth won't work properly. I have a Palm 650 that I sync with my Mac, and now the computer can find the phone but the phone can't find the computer, and I'm in desperate need of help. Anyone?

Restart, booting from your bootable backup/clone of 10.5.4.

Similar Messages

1.1.3 Update & Bluetooth Problems with Nuvi 680

I have been using my iPhone with a Garmin nuvi 680. The nuvi 680 has Bluetooth and can be used as a hands free speaker/mike. I had been using it happily until I upgraded to the 1.1.3 update last night. Now even tough I get an initial connection, it is dropped within a minute or so. Apparently, the connection is reestablished at some point, because after a few minutes the dialog screen warning comes up again telling me that the phone was dropped. This goes on ad infinitum until I unpair the iPhone or turn off Bluetooth. I have tried unpairing and pairing again with the nuvi. It didn't have any effect. I am going to reset the iPhone and try again, but I am not sure that will help.
The most irritating thing about this problem is that the dialog that keeps coming up, has to be dismissed manually before you go back to navigation. After dismissing the dialog 5 or 6 times, I just turn off Bluetooth in frustration.
Has anyone else experienced similar problems? How did you fix the issue?

I am experiencing the same thing. Very frustrating. I got rid of my Motorola Q about 1 week ago and the bluetooth with that phone did the same disconnect cycle (except it also crashed the phone a lot). I have been in heaven with my new iPhone especially with the bluetooth working with my Nuvi 680....for about a week. Now with 1.1.3 I'm back to angry. I would actually seriously consider going back to 1.1.2. I need bluetooth to work with my GPS more than I need homescreen icons or maps triangulation (that's what my gps is for). I'm new to Apple cycle with this type of issue, but I hope that I'm pleasantly surprised to find a quickly rolled out fix.

Latest SMC Firmware update causing problems?

Hello,
recently, I've attempted to install the update: MacBook Pro SMC Firmware V 1.7 and had issues booting up my system afterwards. I thought I ran my RAM down to its skivvies and it was rebelling, but it seems to work fine after repairing the disk drive using Disk Utility, because the first time it happened my Mac wouldn't open things as fast as it usually did, taking about 10-15 minutes to get to the login screen, and then some to get back into the desktop. After shutting it down and rebooting it wouldn't get past the Apple loading screen after the tone. Even with repairing the drive after installing the update, it wouldn't load past the tone and the Apple loading screen, so I restored the system from an external hard drive. This seemed to do the trick and allows me to do everything I used to do prior these problems, and the second time I tried to update the SMC V 1.7 it caused the same problem.
I wondered if anyone else was having these problems with their Macs in regards to the SMC, and maybe it isn't just the SMC but other parts of the MacBook that have problems. Specifically, the Mac I'm using is the 2011 MacBook Pro6,2 2.66 GHz Intel Core i7 with Snow Leopard version 10.6.8. The SMC that I have currently is the 1.58f16 .
Then again perhaps my disk drive and other components are stating their wish to retire. I've used it pretty hard over the past year.
Thanks for reading,
Dracien

Not on my Late 2011 15". But others have had some problems.

Bluetooth problems after latest OS update

On January 18, 2014 the latest Android OS update was pushed to my phone. Since that time I have had problems with the Bluetooth connection to my car stereo through Sync. The phone will connect, but I must manually go into the Bluetooth settings - select the Sync connection settings and enable Use for phone audio and Use for media audio EVERY TIME I get back in my car. These settings were automatically enabled prior to the OS update.
Is there a way to make these settings enabled automatically when this Bluetooth connection is made?
Any help is appreciated.
Thanks.
Cat

catnfran,
I'm sorry to hear that you have been experiencing this issue with your Bluetooth feature! Updates are meant to offer enhancements.
Based on our findings, with the new update, making this change manually would be the recommend option. If needed, we can attempt to master reset the device http://vz.to/1d1KPN1 to see if this helps resolve this particular concern.
EfrainM_VZW
Follow us on Twitter @VZWSupport

I cant seem to download and install the latest iphone software update. I have tried since the release and have been unsuccessful on more than 7 occasions and lost all the data on the process. Anyone have that problem an how do I fix this problem?

I cant seem to download and install the latest iphone software update. I have tried since the release and have been unsuccessful on more than 7 occasions and lost all the data on the process. Anyone have that problem an how do I fix this problem?

Hi
Thanks but I have tried doing the above - when I said 7 times I was modest, its more like 15 times.
And I am referring to the 5.1 software update. I dont have wifi so I guess I will have to try that seeing that my husband also has the same problem - he has also tried downloading several times. It always times out en says that the connection is lost but yet there are always an internet connection and a decent signal once it stopped. Think it said error 32052 or something!
I am disappointed because the update includes inprovement on the battery life - did you guys notice any difference?

Airport & Bluetooth problems after 10.4.7 update

(Note: I posted this in the Tiger forums and after no response, thought I'd try here.)
Greetings,
After updating to 10.4.7, my iMac G5 20" iSight exhibits occasional loss of signal strength in the Airport and poor or lost Bluetooth connections with the wireless keyboard and mouse.
The Airport and Bluetooth problems happen together at the same time. I can see the Airport signal strength drop and seconds later the mouse starts becoming slow and I usually lose connectivity with my keyboard. After about 10 minutes, signal strength returns on both.
The system is well isolated from interference, the cordless phone is a 5 ghz unit, and all cellphones have been removed from the room, but the symptoms continue. The wireless G router is only 3 meters away in the same room.
I reapplied the combo 10.4.7 updater, repaired permissions, cleaned caches using Applejack, zapped the PRAM and reset the SMU but the problem still happens.
Any suggestions? It is driving me crazy.
Thanks in advance for any help.

I'll add a "here, here". I have a 20" iMac G5 (1.8 GHZ). Since applying 10.4.7 I have had Bluetooth disappear twice. Disappear as in: keyboard and mouse no longer function and the bluetooth icon in the menu bar disappears. Power cycle works to recover the system. A far from elegant workaround.

Has ayone experienced any problems withe latest apple tv update

who has experienced problems withe latest apple tv update???

Welcome to the Apple community.
There are always a few that experience some problem or other after an update. Exactly what problems are you having please.

My iphone 4s wifi and bluetooth problem after updating ios 8? please help me...

my iphone 4s wifi and bluetooth problem after updating ios 8? please help me...

Hey there Abdulrahim0259,
I would recommend that you use the following 2 article to help troubleshoot the Wi-Fi and bluetooth issues you are seeing, respectively:
iOS: Troubleshooting Wi-Fi networks and connections - Apple Support
And:
iOS: Troubleshooting Bluetooth connections - Apple Support
Thank you for using Apple Support Communities.
All the very best,
Sterling

Bluetooth problem after update to lollipop

Hi,I've recently updated my 6503 to Lollipop.Everything went smoothly and is working fine, except 2 issues - one solved, second NOT. FIRST (solved) - phone after update waked up and logged to 2G network, with no data transmission (despite it was turned ON). What was strange - my operator's network appeared in 'available network list' as separate 3 NETWORKS ( 2g, 3g and LTE) Switching manually to LTE solved it - now phone is switching between technologies automatically, data transmission is working fine. SECOND AND NOT SOLVED: I'm using the hands-free system built in my car ( mitsubishi lancer, 2008 ) . After update, phone failed to establish connection with it, even hands-free system remained as 'associated device'. OK ... I erased hands-free system from phone, as well as phone from car's memory. Paired devices again - starting procedure from car's side. Nothing better. Erased and paired starting from phone side. Nothing better.What I've observed more: phone after try to establish connection , phone in eye blink looses it. On list of available services of hands-free system (in phone menu ofc) , only 'phone sound' appears, while -as I remember but i'm not sure- before update more (2 or 3) services were detected . PLEASE HEEELP !

Re: Bluetooth problem after update to lollipop As above post, I am also experiencing problems with bluetooth on my Z2:- Phone connection is OK if Bluetooth is turned on the phone for " car is ready". Then I can make and receive calls.
- Playing music on bluetooth does not work after Lollipop 5.0.2 update on my car head unit. Previously connected and able to stream music on 4.4.4 Kit Kat with no issues, looking on web this is not a new issue with Bluetooth connection issues to devices since Lollipop came out so what the **bleep** is going on? I purposely bought a Sony TV, Car Head Unit and Soundbar to ensure everything worked together now the head unit that I only had fiitted in February does not connect which cost me £249!!! No issues connecting to TV or Soundbar but on HU it tries to connect then disconnects and BT Audio Icon on HU display greys out although phone is connected and icon highlighted as connected. I have cleared cache, unpaired and paired again, reinstalled 5.0.2 again through wifi instead of OTA but still the same. Car device: Sony XAV-602BTAndroid version 5.0.2Version: 23.1.A.0.726

I have not been able to access itunes store for over a week now. I keep getting error -1202. I have updated to latest version of itunes but problem still exists. Any tips?

I have not been able to access itunes store for over a week now. I keep getting error -1202. I have updated to latest version of itunes but problem still exists. Any tips?

See this one
https://discussions.apple.com/thread/3742260?start=0&tstart=0

Bug in Latest Mavericks Security Update???

I just installed the very latest Mavericks Security Update as instructed. It was about 500+ MB and took 20 or so minutes to upload and then required a restart to complete installation, which was done. After restart you are asked if you wanted to login to iCloud, etc. the MacBook worked just fine. I shut down normally.
Several hours later upon boot up I first got a "security" warning about only using Apple software. It asks for acknowledgement = ok.
After rebooting the Apple logo shows as normal and the circular progress wheel spins but it never gets to login screen.
What is going on Apple???
Any suggestion fellow Mac users????

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

TWIST: Strange Bluetooth Problem

This doesn't make sense to me. When the system is started from a completely powered off state, the bluetooth radio doesn't turn on and no devices will pair. The bluetooth icon in the taskbar is missing. I tried to manually turn it on but Windows won't let me (in the Wireless section of "Change PC Settings", the Bluetooth option is grayed out).
If I restart the system (from the powered on state), the radio turns on and everything works fine.The bluetooth icon in the task bar is visible and my devices will pair.
My wireless radio always works regardless of how I start the system. It has never failed through all of this wierdness.
I have the Intel Centrino version of the twist (i5, 128GB SSD) with the latest driver and the latest bios version. I tried re-installing the bluetooth drivers but I get the same results.
HISTORY: From day one, I never had any bluetooth or wireless problems. Last week the system was crashing with the error DRIVER POWER STATE FAILURE. After a few of those I checked for updates and installed everything available to me (a bios update and a few other things but no actual drivers). After the updates, the bluetooth problem occurred. However, it's been a few days and I haven't had the Power State Failure crash.
I ran Lenovo's hardware scan and there are no problems with any devices.
Anyone have ideas what could be wrong?

I have been on the phone to Lenovo support. They say it has to do with power management, not all services restoring when PC is turned on. They asked me to,click the start button, run, enter compmgmt.msc, This opens a window to Computer Management. Now open device manager, expand Bluetooth, right click Broardcom Bluetooth 4.0, properties, power management tab, uncheck 'allow the computer to turn off this device to save power". I did all this and it made no difference on my PC. He then went on to say there is another way but it will add 10 seconds to the startup time of my PC which I am not willing to do. So things remain the same until I find a better solution. Has any one else had any luck with this annoying problem? Now I never shutdown my laptop, I just close the lid. Bluetooth starts again when the lid is opened.

Apple TV2 Just Disappeared from Remote app on iPad and iPhone after latest Remote app update

I Have used Remote app on my iPad and iPhones to control my ATV1, ATV2, and ATV3 for years. After the latest Remote app update ATV2 has disappeared from tRemote, and I can no longer find a way to connect it. Any advice about this?

Brilliant. Restarting did the job, and all is well. Since I have recommended this to others with other ATV problems, I'm a bit embarrassed that I didn't try it myself at the outset, and would probably have come around to trying it later, but you saved me some time. Thanks.

After installing the latest itunes/quicktime update, I can no longer access the itunes store and my iphone does not complete syncing. What can I do to fix this?

After installing the latest itunes/quicktime update I can no longer acces the itunes store nad my iphone does not complete syncing. What can I do to fix this? I have tried uninstalling and reinstalling itunes. I have uninstalled and reinstalled windows updates. I have checked the firewall settings. what else?

The problem is with version 10.4.1. I had to reload 10.3 to get it to work. The recommendation from a previous poster worked for me. Here was their list of steps:
Go to Control Panel>Programs>Uninstall
2. Uninstall the following Apple programs in the following order:
     a. iTunes
     b. QuickTime
     c. Apple Software Update
     d. Apple Mobile Devices Support
     e. Bonjour
     f. Apple Appllcation Support
3. Reboot PC
4. Find, Download and Install iTunes 10.3 (you can find it at FileHippo.com)
If you start iTunes now you will get an error message saying that the current iTunes library was created by a newer version of iTunes. To correct this:
5. Go to your Music>iTunes folder and delete the "iTunes Library.itl" database file
6. Within this iTunes folder find and open the "Previous iTunes Libraries" folder and locate the most recently dated "iTunes Library (date).itl" database file.
7. Copy and Paste this file back into the iTunes folder
8. Rename this "iTunes Library (date).itl" file by removing the date. It should say "iTunes Library.itl"
9. Reboot PC

Updater Software Problem

After installing the updater software and iTunes 5.0.1 I am in a position were my iPod is not being recognised by my PC, firewire or USB connection. When I try to start my iPod the Apple logo shows and then the connector icon and an arrow appear indicating connect to PC. There seems to be a few threads on this matter, is this an Apple fault?

Up unitl yesterday all was fine, it has worked for a year. Then I install the latest iTunes and update software and I'm in this position. I have uninstalled and reinstalled the software with but still the same problem.

Latest OS X update & Bluetooth problems

Similar Messages

Maybe you are looking for