Latest uefi and legacy bios for R9 280X Gaming 3G

By working too late with too little sleep, I'm afraid I've done something pretty stupid while trying to flash two separate R9 280X Gaming 3G cards; I've corrupted both the legacy and hybrid bios on both cards. And (wait for it) I don't have backups of the original ROMs. Fortunately, I have a third card I can run the machine off of while I flash the hosed cards, but I need the ROM files. Could someone please point me towards the proper legacy and hybrid ROM files for these cards? The serial numbers, in case it matters, are 602-V277-34SB1402014989 and 602-V277-44SB1312123180.
I promise I'll be more responsible in the future. Thanks!

Yes, that's the picture I was referring to. If you take it literally, it's showing that position two (the UEFI bios) is towards the side of the card with the power connectors (on the right, if you're looking at the side with the fan). However, while only one of the R9 280X cards I have is labeled on the motherboard, it shows position 2 as being towards the end of the card with the video connectors.
To state that more simply, I suppose, the picture on the page you linked implies that the polarity of the switch shown is in relative to when you're looking at the card from the fan side. I think what's actually going on here is that the picture of the card with the fan is just intended to show where the switch is; the actual close-up of the switch is actually from the side with the motherboard visible (in other words, position 2 is towards the end of the card that is visible at the back of the computer case).

Similar Messages

  • [Request] Latest BIOS for R9 280X Gaming 3G

    Card: MSI R9 280X Gaming 3G
    S/N: 602-V277-250B150100xxxx
    BIOS ver: 015.042.000.000.003435

    The attached is the latest UEFI/GOP vbios for your card (TV277MH.351).
    We are unable to check what version you have now though as the numbers you have taken from GPU-Z are not a real vbios version.
    The actual vbios saved to file is required to check. If you want to flash the attached follow the below.
    Create a bootable usb stick (https://forum-en.msi.com/index.php?topic=165175.0).
    Unpack the provided archive (TV277MH_351.rar) and put the included file (351.rom) on that stick.
    Put the atiflash.exe also included in the archive on the USB stick too. Now boot from the stick.
    Type atiflash -p -f -noaper 0 351.rom [ENTER] and let it flash the vbios.

  • [Request] Latest BIOS for R9 280X Gaming 3G with Samsung RAM

    Card: MSI R9 280X Gaming 3G
    S/N: 602-V277-44SB1312xxxxxx
    BIOS ver: 015.042.000.003.000000
    ROM msg: 113-MSITV277MS(or MH for UEFI).380 TAHITI B0 XTL C38650 GDDR5 3GB
    RAM: Samsung K4G20325FD-FC03
    Thanks

    you are using latest versions

  • [Request] Latest (or alternative) bios for R9 280X Gaming 3G

    I'm having artifacts, graphical errors and crashes in games, in desktop and when watching videos, so basically all the time. I have tried 13.12 official and 13.11 beta -drivers provided by AMD and the one provided by MSI, no help there. I could try newer/older/some other bios for this card before sending RMA.
    Serial number: 602-V277-38SB1401020604
    Current BIOS: https://dl.dropboxusercontent.com/u/43449874/Tahiti.rom

    Current setup:
    CPU: 4670k
    MB: Asus Z87-A
    PSU: Seasonic x-560
    RAM: 16GB Corsair 1600MHz 1.5V
    SSD: Samsung 128GB 840 pro
    I have OC'd the CPU, will try later with stock settings. I could also give a try for removing one set of RAM or setting it to 1333MHz. I can try the R9 in another computer in couple of days when a PSU for my 2nd machine arrives.
    Edit: Forgot to mention, the system is completely stable with another GPUs I have tried.
    Update: Removed one 8GB kit of ram, set the rest to 1333MHz. Set CPU to stock speed and voltages. Nothing changed, still artifacts.

  • [REQUEST] UEFI/GOP VBIOS BIOS for GTX 780Ti Gaming 3G

    Hello, I am having some issues with windows 10 and fast boot where black screen comes up on windows boot. I've reinstalled drivers, uninstalled drivers, formatted my OS hard drive, tried everything, the problem continues to come back.  I even decided to go back to Windows 8.1, same issue. nVidia is suggesting I need a new video BIOS for my GTX 780Ti Gaming 3G.
    The version on my card per system information is 80.80.34.00.35
    The serial of my card is : 602-V298-12SB1402080334
    Any help is appreciated.

    save and upload your current vbios

  • Requesting UEFI GOP BIOS for R9 280x gaming 3g

    hi as the title says. a vbios for this card plz.
    s/n 602-v277-31sb1402067820
    not allowed to post links, this is what gpuz says on the bios info: 015.041.000.000.003435(113-C3865000-O77)
    thx for the help

    This vga has two vbios chips which can be selected with a switch on top of the card. One should be legacy (default position) and one should be GOP. Have you tried both?
    If so and none is GOP add a copy of the vbios (save to file and uploaded to some file hoster afterwards add link here). If not allowed to link yet simply mask the link with a break.

  • 660Ti UEFI/GOP & legacy bios request.

    Hi.
    Preparing myself for the Haswell upgrade.
    Can I please have the latest UEFI/GOP & legacy BIOS(es) for the following card?
    Card: MSI N660Ti PE 2GD5/OC 2GB.
    Serial#: 602-V284-050B1211045023.
    Original Vbios: 80.04.4B.00.16 (P2004-0001).
    Vbios image dump: (*https://www.dropbox.com/s/y6crdr9y1ti5t6u/MSI%20N660Ti%20PE%202GD5-OC%202GB%20GK104%20original%20bios.rar *)
    Thanks.
    PS.
    Which ver. of nvflash should I use for flashing?

    Thanks for the file.
    I upgraded just for the sake of being up-to-date,
    but I solved the problem earlier otherwise 
    So, I can't really comment if the newer/provided VBIOS solves the black screen problem or not.
    In my case the problem was from Nvidia driver 320.18.
    There is a supposedly acknowledged problem with Win 8 which silently installs  on the background
    an earlier Nvidia driver (311.06) from windows update,
    and *not* informing the user about the background install/need for reboot.
    If the user installs another/later driver without rebooting 1st it becomes a driver binary mess.
    In my case, when using 320.18 with Win 8 (even from a clean install and not messing with any previous driver),
    caused the monitor going to sleep after POST and when MB UEFI handed-off control to OS in 80% of the cases.
    A situation I could exit from only with a hard shutdown.
    So, for any other poor soul having similar problems,
    it might be a good idea to try an earlier Nvidia driver.

  • [Request] BIOS for R9 280x (19SB)

    Hi guys,
    This is a different thread, different card
    Can you send the a "good" bios for :
    R9 280x GAMING 3G
    S/N : 602 - v277 - 19SB13090980xx
    I installed this (https://forum-en.msi.com/index.php?topic=174707.msg1268039#msg1268039)
    And works fine, but fans are under 40% , with HIGH temps (80ºC  Fans 40%)
    THANKS 

    those are latest versions, there is no newer

  • Request: UEFI BIOS MSI R9 280X GAMING 3 G

    Hello there,
    I require a uefi bios for r9 280x gaming 3 gb graphics card.
    S/N: 602-V277-19SB1309097412
    Link to my bios:htt://www.dropbox.com/s/36lp55nqkbwn2cc/Tahiti.rom which was extracted from gpu-z
    Could you please also show me tutorial on how to actually flash bios cause i'm rather new on this entire matter :D
    Thank you for your help.

    here it is
    For flashing: http://www.techpowerup.com/downloads/2232/ati-winflash-2-3-0/

  • Switch from uefi to legacy bios

    How would you go about switching from uefi to legacy bios/boot? Would you have to reinstall windows? Can you use the hidden partitions for this? Would you need a windows install disk?

    how do I switch my partitioning scheme to MBR so I can use legacy boot/bios?
    In the System Configuration section of the UEFI, for starters, set the Boot Mode to CSM Boot. That essentially bypasses the UEFI.
    The easiest way to change the partitioning from GPT to MBR is to use old fashion tools like a Windows 7 installation DVD to delete the existing partitions and create new ones.
    -Jerry

  • [Request] UEFI Secure boot Bios for: GTX660

    My old motherboard died so i have replaced my computer, I now have:
    4690K
    32gig ram
    Asus Maximus hero Vii mobo.
    All set to using secure boot / UEFI.
    Have installed windows on a fresh GPT partition with secure boot and Im currently using the On Chip HD4600 graphics.
    My GTX660 is sat beside me on the desk. (It's *waving* , currently feeling neglected)   
    Im unable to boot to Win 8.1 with the card plugged in as the computer complains about a non UEFI device.
    Info from GFX card box:
    912-V287-001
    N660 TF 2GD5/OC
    PCI - E,N660,2G,GDDR5,Twin Frozr,OC,
    DL - DVI - I,DL - DVI - D,HDMI,DP,
    Power Cable,SLI
    S/N:602 - V287 - 04SB120902****
    I do not know the current BIOS on the card.
    1) As im currently unable to boot to windows with the card installed can the entire flash procedure be done from a DOS enviro?
    techpowerup.com/downloads/2257/nvflash-5-136 - I think it can.
    2) Can somone provide me with a suitable bios file please?
    3) Once I perform this flash will I be able to use this GTX660 an old non UEFI system? (I plan to sell this card on , and get a MSI GTX970 next paycheck)

    Use the attached.
    Decompress the provided .rar archive with Winrar: http://www.rarlab.com/download.htm
    Then flash the included file with Nvflash for dos: http://www.guru3d.com/files_details/nvflash_download.html
    To do so rename the included file to .rom and create a dos bootstick (https://forum-en.msi.com/index.php?topic=165175.0)
    Put nvflash and the vbios file on it and boot from the stick. Then type nvflash -4 -5 -6 gop.rom (if renamed vbios that way) and hit enter. Confirm the questions and let the tool flash
    Quote from: farrantcj on 06-June-15, 15:52:09
    3) Once I perform this flash will I be able to use this GTX660 an old non UEFI system? (I plan to sell this card on , and get a MSI GTX970 next paycheck)
    Old boards with a legacy bios will have no problem as the vbios is hybrid and can work in UEFI and legacy mode. Only older boards with a UEFI bios that is not GOP compliant might run into issues.

  • UEFI and Legacy .... tips

    I was  installed ubuntu alongside windows8 but while restarting PC directly windows8 loaded, even I enabled Legacy mode. In BIOS setting it was clearly given that "In Legacy mode both UEFI and Legacy are available and UEFI has heigher priority ".
    How to change the priority and how to load both operating systems and give a choice to us to select one of them while starting PC. 
    " HP Pavilion g6-2202tx Notebook PC "
    please provide me the details.

    I found that there is no way to change the boot order priority ...,
    this is the link saved my time...
    http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-Software-Recovery/UEFI-vs-Legacy-Boot-order/m...

  • Request for a GOP UEFI bios for R9 270 gaming 2g

    Request for a GOP UEFI bios for R9 270 gaming 2g
    thank you

    Request for a GOP UEFI bios for R9 270 gaming 2g
    thank you
    BIOS
    http://qd.baidupcs.com/file/f854518f3ebcb6e0918296e99dedbe39?xcode=651e731f64d217396dcee8d89df53b8bbc89b6a7ca8cf985&fid=1141293504-250528-731006637695005&time=1396108361&sign=FDTAXER-DCb740ccc5511e5e8fedcff06b081203-QapW05N0P5fS7fKuuF9rsE%2BzbVI%3D&to=qb&fm=Q,B,T,t&newver=1&expires=8h&rt=pr&r=691888291&logid=3537789216&vuk=1141293504&fn=Pitcairn.rom

  • Request for a GOP UEFI bios for R9 280 GAMING 3G

    Request for a GOP UEFI bios for R9 280 GAMING 3G

    Quote from: flobelix on 25-April-14, 22:32:46
    You need to add a bit more: GOP / UEFI Vbios requests - Read Here First
    Hi,
    I'd like a GOP VBIOS for the R9 280 3GB
    SN: 602-V277-46SB1403050298-W92
    Thanks

  • Need latest  SLD and NWDI version for PI 7.1 EHP1

    Can any one update me the latest  SLD and NWDI version for PI 7.1 EHP1?
    Kindly provide me the path of implementation guides for SLD, NWDI  which can be used with PI 7.1 EHP1. For PI 7.1 EHP1, can we use the same version of  SLD and  NWDI which used IN PI 7.1?
    Please help me for the above questions.
    Regards,
    Yuvaraj.

    Hi Yuvaraj,
    Please check the NWDI Development Infrastructure 7.11 and SLD 7.11 for the PI 7.1 EHP1.
    Go to Service Market Place - Software Download > Support Packages and Patches > Support Packages and Patches - Entry by Application Group > SAP NetWeaver and complementary products > SAP NETWEAVER PI > SAP EHP1 FOR SAP NW PI 7.1  >Entry by Component > Development Infrastructure.
    Hope it will helps
    Regards
    Arun Jaiswal

Maybe you are looking for

  • Acrobat X freezes when I run the search function

    Every time I run the search function Acrobat X, Acrobat freezes and then locks up. This is happening on two different computers, both of them are running Acrobat 10.1.1. I've also repaired both installations through the control panel in Windows 7.any

  • Classes not found in package

    I am migrating an Workshop application from 7.0 to 8.1. Classes under com.company.ctrl.*.ctrl and *.wsdl can't be found by the classloader, while all classes in the com.company.* can be found.... Anyone having similar problems???

  • Auto shot down no longer works

    I pulled a power plug out of my iMac. And now my 2 external Seagate drives no longer auto shut down. They stay on unless I pull my firewires 800 and 400 out. The new Free agent Seagate doesn't have the on and off buttons. Its very frustrating. What h

  • PDF Creation - how to return output to user?

    I am using PDFLib to create dynamic pdfs. I'm having a hard time trying to return the pdf to the user. I tried using a ServletOutputStream but I keep getting an IllegalStateException. I believe this may be because I am already using a PrintWriter els

  • Install Digital filter design toolkit on labview 8

    I get an error that says: You must install labview FDS or PDS 7.1 (or later) before running Digital Filter Design Toolkit 7.5 Setup. I have only Labview 8.0 installed.