Latitude E4300 don't see new Seagate 750Gb HDD

I'd like to change my old Seagate 160gb 7200rpm disk to the new one: Seagate Momentus 750GB 7200rpm (st9750420as). I don't know why but the e4300 BIOS can see this disk only sometimes (i've noticed that it's happens only when i've unplugged the CMOS battery, left laptop alone for day or two or plugged the disk to my eSATA adapter, boot system from it and plugged it back to e4300).
Disk works fine in all other laptops that I have but not with this one (and even with this eSATA adapter on this e4300 works in everytime!).
The only difference that I see between those disks is current consumption (0,7A in 750gb and 0,62A in 160gb), maybe it's relevant?
I've tried all of the SATA settings in BIOS (ATA, AHCI, IRRT), with no difference.
Can you help me?

I think that the problem is causing by the Dell's Fast boot option in bios that was enabled. Anytime when I changed something in laptop hardware (put another ram memory or reset CMOS), bios have to be turned up in the normal (longer) way. But the second and subsequent boot on the same configuration has always failed, because it's trying to fast boot.
I turn off the fast boot option, but it's solved the problem only partially.
Do you know, what could cause this problem and how can I turne the Fast boot on with this particular HDD?

Similar Messages

Cannot install OS X Lion after new seagate hybrid HDD install

I just installed new seagate hybrid hdd (STBD1000400) in my early 2011 13" Mac Book Pro after stock drive failed;
formatted it as mac os extended (journaled);
downloaded lion installer and copied it to external with OS X Lion bootable drive;
started computer from external drive;
ran lion installer;
"Install Failed: OS X could not be installed on your computer. OS X can't be installed on the disk (null) because a recovery system can't be created. Visit www.apple.com/support/no-recovery to learn more"
I reduced partition size and same error. Any suggestions

Remove the SSd from inside the case and connect it to that same Mac with a SATA to USB adapter, one that has its own AC power supply (Not a USB BUS power adapter), and try to install Lion on it.
I am suspecting the cable that goes from the drive to the logic board is faulty which is very common.
If the drive works fine outside the system, IE you can install Lion on it and it creates the Recovery HD partition and you can boot and run the system from it then is is more than likely the cable.
One other thing to do is after you Repartition the drive in disk utility grab the bottom right hand corner of the partition layout area and drag it up a little shrinking that partition by a couple of 100MBs to 1-2GBs and try the install again.
There was a bug in some Macs that for some reason with the whole drive included in the primary partition the OS X installer couldn't create a Recovery HD. You don't have to create a second partition, you can just leave it as Free Unpartitioned space. If you can then successfully install Lion you can then Drag the corner back down to put the free unpartitioned space back into the main partition.

Don't see new UI in FF v21

I have FF v21 for Windows but I don't see the updates to the UI. For instance, my tabs are still under my bookmark toolbar, I don't see the Firefox button in the top left and I don't see the bookmark button on the right. I'm using an add-on theme but tried setting it to the default to see if that made a difference...it didn't.

This is because you are on Windows XP. Firefox doesn't switch XP users over to the new UI on an update. You can turn it on however if you'd like. Go to View, then Toolbars, then uncheck the Menu Bar. You should see the Firefox button now.

My CC applications are up-to-date but I don't see new features in InDesign. Why?

I've updated my Indesign but I don't see any of new features or they don't work. Why???
Does a corporate member make any difference to this?
Thanks for your help (if anyone could....).

Check your Creative Cloud app. Otherwise run the cleaner tool and start from scratch.
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
Mylenium

Ipod touch update with january apps, don't see new apps

Hi, I've buy the january update for add the new apps to my ipodtouch, but just transaction complete my ipod don't update with new apps. I try to syncronize but i don't see any new icons on my ipod.
I see on my itunes property and purchase is complishied.
Any suggest?
Thanks, Marco
(sorry for my english...)

I have the same problem as Marco. I have tried everything in the article from Apple but it was absolutely no use. I had tried everything that it suggested before I even went online to try to see if anyone else had the same problem. I wasted almost my whole Saturday trying to resolve this, all to no avail. If anyone has a solution I would be very grateful. I am an ardent Apple supporter, and have recommended Apple computers to many friends and relatives. I am therefore very disappointed that Apple has gone back to its bad habits of releasing software that has obviously undergone little or no beta testing. I hope a solution can be found quickly.

I don't see new image versions when exporting, etc.

Hi,
When I try to post pictures from FB to Aperture, I don't see any of my edited version, only the originals. This also happens with other applications...including setting my desktop photo under system preferences.
Any suggestions?
Thanks.

To see the edited versions of your images in the Media Browser and to be able to set the Desktop etc., you need to create Previews in Aperture. How are your Preview Preferences set?
Aperture -> Preferences -> Previews
Regards
Léonie

My new Time Capsule 2T 2013 doesn't see my Seagate External HDD

Hi,
I am new MAC user recently converted from PC. I have a Macbook Air 2013 and the new time capsule 2013 as well.
I did connect my external HDD (i.e. 1.5T Seagate HDD) in the Time Capsule USB port.
I went into the utility Airport Application to make sure "File sharing box is checked".
I went in Finder to look for my HDD and no sign of it...
I read many many discussions looking for the answer on how to make my External HDD (previously used on my PC laptop) appear on my MacBook Air throught my home network, but without success. From Apple website, it seams to be an easy task...!
Finally, I have read stuff about how the HDD is formatted. Could it be the reason?
I need some help please!
Thanks in advance.
FLTower.

Finally, I have read stuff about how the HDD is formatted. Could it be the reason?
I need some help please!
It surely is at least a major factor.. maybe several are involved.
You cannot see a disk formatted NTFS.. ie standard windows format from TC.
The disk must be plugged into the Mac and open disk utility..
You need to change the partition over to GUID from MBR.. and change the format to Mac OS extended Journaled.. or HFS+
Although FAT32 is also supposed to work.. that will lead to other issues.. don't do it.
If you format a drive with data on it.. your data is gone.. just to make sure you know that.
You can plug the drive into the computer and copy the data to another location.. and then format the drive.. and copy it back.. if you have an air without the Thunderbolt to Ethernet adapter this will take aprox 1month to achieve.

Cannot see new Seagate 1TB Hard Drive on SBS 2008 R2 (Onboard RAID)

This is probably an easy setup, but I just want to make sure that I am doing this correctly and not mess up the current Raid Array.
This is on a Intel S5000VSA server motherboard. It has an Onboard 6 port RAID card. Currently there are three SATA HDDs connected to the right of the Onboard RAID (if you are looking at the Motherboard directly). There is another connection that
least to an external SATA port that is connected to the left of the Onboard RAID. My boss purchased a 1TB Seagate and want is connected onto the server as its own drive; not connected to the current RAID array 0.
I have installed the new 1TB Seagate to the next open port next to the eSATA connection. When I start up the server, during the boot up I see the 3 hard drives (the three original and the new 1TB). When the Windows SBS 2008 R2 finally boots up and I open
the Disk Management, I do not see the new Hard Drive that I installed; I only see the existing C: and external BackUp. I tried to rescan the drives but no go.
Do I need to set up a new Array for the new 1TB Drive?
Just to look, I did launch the RAID Bios and confirmed that the RAID does see the new Hard Drive and has a READY status. I know I do not want to do a New Configuration, because it will clear the current configuration. When I select the view/add configuration,
I can set the new Hard Drive status from READY to Onlin A01-00. When I save and exit, then look at the physical disk status again, it reads as ready.
I don't think I have to add the new Hard Drive as a new array, but I could be wrong. I wanted to get some input before I do anything else further.

After some looking around, I found a Document about the RAID Controller on the motherboard. Instead of adding the new Physical Drive as a Virtual Drive in the RAID Bios screen, I found that I was able to download an Intel Console version that was more user
friendly.
I did add the new physical drive as a new Array and once that was done I was finally able to see the new 1TB in Disk Manager.
Thanks for that Assistance Al.

IPhone and Other 2.4GHz Units Don't See New Time Capsule Net

Problem: My iPhone and other 2.4GHz equipment do not see my new Time Capsule network.
I had an old circa 2006 Apple Extreme network and decided to upgrade with a dual-band Time Capsule. After setting up the Time Capsule with as close to the old settings of the AEBS as I could, I am no longer able to see the network with either my iPhones or other 2.4GHz units. I'm currently running with only the Time Capsule. The AEBS is off, although I do intend to add it to the network after my initial configuration problems are solved. I've searched the discussions for problems like mine and worn out Google looking for the answer. I'm stumped.
Here are some of my setting on Airport Utility:
Create a wireless network
Allow this network to be extended is checked
Radio Mode: Automatic (I've tried several combinations by holding down the option key, but none seemed to change anything)
Radio Channel - Automatic (summary shows 149 (automatic) and 3 (automatic) currently
Wireless Network Options - use wide channels is checked
Guest network enabled
Internet Connection is PPPoE

do you know what encryption is being used?
is the same at work?

Don't see new Item on Purchasing

Hi my friends!
I have an error. I create new item on OPM inventory. But when i create a Purchase Order, I can't find it.
Can you help me?

Hi
Syncronize all OPM Items should assign to all OPM organizatios. You need to mainly assign it to all OPM Warehouses and Organizations in which the material is to be received. The above process is good for syncronization.
Now. why you cant see hte items still. Please cehck you purchasing setups to see if there is any problems
Also, in Discrete Item Master check if the flags of "Puchasable", "Inventory" etc.. are checked at both Master Org Level and Item Organization Level
Regards
Girish

Ios 5 Update New Features says that iCal now has a week view for iPhone but after updating last weekend, I don't see any week view--just List, Day and Month..How do I get the week view?

ios 5 Update New Features says that calendar now has a week view but after updating my iPhone 4 last weekend, I don't see any week view for iCal--just List, Day and Month as in the past. Is the weekly view available for iCal and if so, how do I access it?

Rotate your phone to landscape.

HT204150 After having upgraded to mountain lion, the application "contacts" doesn't run. I don't see any contact and add new contacts . The application doesn't run

After having upgraded to mountain lion, why the application "contacts" doesn't run? Why is impossible add a new contact and I don't see old contacts that I can see on my Ipad?

I have the same problem. I would like to include this information:
.- A message "error CoreDAVerrorDomain 1" is shown
.- with other user, in the same MAC I do not have the problem

I can't sync any new songs to my iPod, when i plug it in my computer I don't see the iPod icon on iTunes, please help.

I can't sync any new songs to my iPod, when i plug it in my computer I don't see the iPod icon on iTunes, please help.

iOS: Device not recognized in iTunes for Windows
iOS: Device not recognized in iTunes for Mac OS X

I had to upload itunes on a new computer and after the iphone was updated my music was not on my phone and i don't see any music on my itunes any suggestions

I had to upload itunes on a new computer and after the iphone was updated my music was not on my phone and i don't see any music on my itunes any suggestions

iTunes- How to move your music to a new computer
Syncing to a "New" Computer or replacing a "crashed" Hard Drive

How do I authorize my new PC to purchase from itunes store? (it says go to Store menu and choose Authorize Computer but i don't see that option anywhere)

How do I authorize my new PC to purchase from itunes store? It prompts me to go to STORE menu, then choose Authorize this Computer (which i don't see anywhere) or Advanced (which I don't see anywhere).

There's a couple of ways to get through to the authorisation controls in the 11.0.x versions.
The control is still in the Store menu, but first (if you're using iTunes versions 11.0.x) you might need to bring up the menu bar to see the Store menu.
If you're using 11.0.x, click on the wee boxy icon up in the top-left corner of your iTunes to see the "Show Menu Bar" control, as per the following screenshot:
Then you'll find the control in the Store menu:
Alternatively, if you don't want to bring up the menu bar, it's still possible to get into the authorise controls via nested menus accessible from the wee boxy icon. Here's a screenshot of where to find them:

Latitude E4300 don't see new Seagate 750Gb HDD

Similar Messages

Maybe you are looking for