Latitude E6330 BSOD via SCCM 2012 R2 OSD

Hi All,
I'm currently struggling to build some Latitude E6330 laptops via SCCM 2012 R2 CU3 OSD . I'm getting a BSOD with error code 0000007E after the drivers are applied and the laptop reboots.
I've built nearly 100 OptiPlex desktops without issue from the same server. I've tried both the A09 and A10 E6330 driver CABs, and both have the same issue. I was having an issue even building the boot image with these drivers, but removed a faulty driver
before importing them into SCCM (Conexant USB Modem driver) which resolved that issue. I'm assuming that the removal of this driver wouldn't be causing the BSOD - but I'm currently trying to find a replacement driver to see if that resolves it anyway.
I've tried using 'Auto Apply Drivers' and 'Apply Driver Package' in the task sequence, using a WMI query and also without a WMI query to no avail. I've blown away all previous drivers, imported only the A09 and then blew away + imported only the A10
drivers, rebuilt the driver packages and re-added to the boot image numerous times. Yep I've been distributing/updating distribution points each time too :)
Unfortunately I can't get onto the laptop to check the smsts/setupact/etc etc logs because it blue screens even in safe mode.
My last resort will be to add just the network+HDD drivers, and then slowly add drivers until I figure out what driver is causing the BSOD. Unfortunately this would be quite a lengthy procedure, so I'm hoping that someone has had a similar problem and
may know which driver could be causing me this grief.. Or perhaps could point me in a different direction as to what may be causing this issue....
Thanks for your time.

Are you trying to deploying Windows 7 to the laptops?
If so does your WIM file include the platform update (how long has it been since you created / updated it)? If not then you may need to update / capture a new wim and try again.
A lot of newer drivers will cause this sort of problem if you try and inject them into an older wim file.
If this isn't the case, then I have had this happen to me a long time ago with a webcam driver so maybe exclude these drivers first? A long shot though.
Cheers
Damon

Similar Messages

ThinkPad X1 Carbon 2nd+OneLinkPro Dock = No IP Address During Imaging (OSD) via SCCM 2012 R2

I'm trying to image a second generatoin X1 Carbon that also has a OneLinkPro dock attached via SCCM 2012 R2.
The USB stick is plugged into the dock, as is Ethernet & power.
When I boot into the preinstallation environment, I don't have an IP address.
The USB stick is fine - works on all 26 other devices here
The network cable is fine - I'm able to get an IP & image from other systems
I tried two OneLinkPro docks, same problem on both
If I use the Ethernet adapter, it works fine
I'm convinced its a driver issue at this point.
I was directed to www.lenovo.com/onelinkdrivers to locate OneLink dock drivers, and I've downloaded the package.
The downloaded EXE (tp_onelink_dock.exe) extracts to C:\SWTOOLS\DRIVERS\Dock by default
In C:\SWTOOLS\DRIVERS\Dock you have another EXE Setup_OneLink_Dock_Lenovo_v10826.exe
This immediately launches an installshield setup (run from %temp%)
There no options to extract the drivers - it just installs the drivers, and none of the switches I've thrown at it have yielded any results.
I found a data1.cab file but I can't seem to extract anything with 7Zip or expand
How are folks with second gen X1 Carbons who use SCCM for OSD successfully imaging those machines with the OneLinkPro dock? (without the use of the Ethernet adapter of course.)
Solved!
Go to Solution.

Fauxlution:
Install drivers on an x86 machine
Navigate to C:\Program Files\Lenovo\Onelinkdock (or something like that)
Grab the driver directories & save them elsewhere
Repeat process for x64 machine because the installer will only install drivers for the architecture of the system its run on. (x86 system = x86 drivers; x64 system = x64 drivers)
Clean up the drivers (extra non-essential files in there)
Import both sets of drivers into SCCM
Bake architecture specific Realtek drivers into boot image
Couldn't be simpler.

Lync 2013 x64 silent client deployment via SCCM 2012 SP1

Greetings everyone!
I ran into a problem with Lync 2013 x64 silent deployment.
I need to provide every workstation with Lync 2013 client, so i decided to use deployment via SCCM 2012 sp1.
I created 2 msp files with OCT, one based on x86 Office 2013 Proplus, and other based on x64 Office 2013 Proplus.
Added them as applications to sccm software library.
Deployment of Lync 2013 x86 application was a success with over than 80% compliance.
But all Lync 2013 x64 automatic installations finish with different errors.
I created special device collection for workstations with office 2010 x64 and 2013 x64, because i can't install other architecture products once it has x64 product installed.
My membership query-rules for this collection:
Office 2013 x64
select SMS_R_SYSTEM.ResourceID,SMS_R_SYSTEM.ResourceType,SMS_R_SYSTEM.Name,SMS_R_SYSTEM.SMSUniqueIdentifier,SMS_R_SYSTEM.ResourceDomainORWorkgroup,SMS_R_SYSTEM.Client from SMS_R_System inner join SMS_G_System_INSTALLED_SOFTWARE on SMS_G_System_INSTALLED_SOFTWARE.ResourceId
= SMS_R_System.ResourceId where UPPER(SMS_G_System_INSTALLED_SOFTWARE.SoftwareCode) = "{90150000-0011-0000-1000-0000000FF1CE}"
Office 2010 x64
select SMS_R_SYSTEM.ResourceID,SMS_R_SYSTEM.ResourceType,SMS_R_SYSTEM.Name,SMS_R_SYSTEM.SMSUniqueIdentifier,SMS_R_SYSTEM.ResourceDomainORWorkgroup,SMS_R_SYSTEM.Client from SMS_R_System inner join SMS_G_System_INSTALLED_SOFTWARE on SMS_G_System_INSTALLED_SOFTWARE.ResourceId
= SMS_R_System.ResourceId where UPPER(SMS_G_System_INSTALLED_SOFTWARE.SoftwareCode) = "{90140000-0011-0000-1000-0000000FF1CE}"
My application deployment type points to setup.exe in office 2013 x64 installation folder, where i created msp file in updates folder via OCT and edited config.xml file in proplus.ww folder.
So my installation program looks like this setup.exe /adminfile updates\1lync.msp /config proplus.ww\config.xml
The same configuration works with Lync 2013 x86 deployment, except other setup folders.
When i try running installation program setup.exe with /adminfile and /config parameters locally, it installs successfully without errors or warnings.
I'm trying to find out problem source, does anyone have ideas what I am doing wrong?
Also i'm trying to reduce office 2013 installation folder size, what subfolders are necessary for Office 2013 proplus installation (still installing only lync with common files and tools)? Because now 3.5 GB package is quite hard to distribute to sccm secondary
sites with deployment point.
Thanks in advance.

Hi,
Here are some tips and tricks for your reference.
Tips and Tricks: Deploying Lync 2013 client using SCCM 2012 | Lync 2013 Client Customization for SCCM 2012 Deployment Package
http://zahirshahblog.com/2014/01/08/tips-and-tricks-deploying-lync-2013-client-using-sccm-2012-lync-2013-client-customization-for-sccm-2012-deployment-package/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

App-V 5.0 SP2 user applications published via SCCM 2012 to VDI workstations with roaming only

Hi,
The environment consists of App-V 5.0 SP2 (KB2956985) user based applications published via SCCM 2012 to Windows 7 VDI snapshotted workstations that are reset at user logoff.
When a user logs on the SCCM 2012 client initiates App-V client package publishing. After a couple of minutes after logon the shortcuts appear and the user can launch their applications.
The issue is that at logoff, even with roaming enabled, the publishing information disappears. This causes the next logon process for that user to repeat, the applications are not available until the SCCM client has completed it's publishing cycle.
Roaming profiles are implemented. %APPDATA% is redirected to a UNC path. The following registry key is set
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\AppV\Client\Integration\PreserveUserIntegrationsOnLogin=1
U-EV, global publishing of applications, and AppLocker rules are not an option. Also, I have read this already - http://technet.microsoft.com/en-us/library/dn659478.aspx#BKMK_PE
I do not want to wait for the SCCM client to kick in prior to the user applications being available. What do I need to roam or run to create a seamless transition for the user between sessions?
Eddie.

Hi Tywin (bad username considering the last GoT Episode ;))
If you ask Microsoft, they always recommend using SCCM for deploying App-V packages and reuse your current SCCM infrastructure if that is already in place. Problem is, as you now experience, is that there is some big caveats both in regards to publishing
time and to roaming of settings.
As Nické states I would suggest looking into the Full Infrastructure Model for App-V 5.x, which gives you much better performance in what I call "from no apps" to "being able to click the shortcut" - the add and publishing phase. If you don't have the time/budget/whatever
to start looking into that, you could look into some community tools like App-V Scheduler which is developed specific by Citrix guys to ease the publishing and management in a Citrix world.
Microsoft have a great article about Performance Guidelines, which you have read, but it mostly presumes you work with Full Infrastructure. Have you looked into Steve Thomas' session from TechEd NA? It talks about "implementation trends".
Senior Consultant at Atea Denmark - http://Atea.dk Atea Technical Evangelist for App-V NoLightPeople - http://NoLightPeople.com Access Director - http://www.nolightpeople.com/index.aspx#accessdirector

Shockwave 12.0.0.112 MSI errors when installing via SCCM 2012

I am experiencing the same type of issue i have entered a bug report for Flash Player.
Upon pushing the vendor provided MSI via SCCM 2012, the uninstall of the older version 11.6.8.638 which is pushed enterprise wide, is removed from the machine, but the installation of the new 12.0.0.112 is not actually installing. The log file that was on the machine from the command line we use shows this error:
MSI (s) (A8:FC) [08:02:03:374]: Product: Adobe Shockwave Player 11.5 -- Error 2753.The File 'swhelper_1159620.exe' is not marked for installation.
Anyone else seeing this happening or getting the same issue when installing Shockwave 12.0.0.112 with the vendor provided MSI for distribution?

JVENGLEY wrote:
MSI (s) (A8:FC) [08:02:03:374]: Product: Adobe Shockwave Player 11.5 -- Error 2753.The File 'swhelper_1159620.exe' is not marked for installation.
Anyone else seeing this happening or getting the same issue when installing Shockwave 12.0.0.112 with the vendor provided MSI for distribution?
I didn't have any installation issue on Windows XP 32 bit and Windows 7 64 bit.
You didn't say anything about your OS, btw.
And that swhelper_1159620.exe is a legacy (it's not related to the previous v11.6 or the current v12 installations).
For future, to get rid of installation issues, use the UNinstaller first of all:
http://www.adobe.com/shockwave/download/alternates/#sp
cheers

Trying to deploy a VB Script via sccm 2012 R2

Hello All
This is my first attempt at deploying a script via SCCM 2012 R2 and I seem to be stuck. Essentially what this script does is map a printer. The script on its own works fine. Meaning it works when I double click it and also running it from the command
line. Its when I try to use in sccm things go down hill. I have tried the following from the command line in the package properties.
\\my-sccm-server\Sources\Applications\VBSripts\cscript.exe Impact.vbs
\\my-sccm-server\Sources\Applications\VBSripts\Impact.vbs
Phil Balderos

looks good :)
You can check execmgr.log on the client to monitor the install as it is running.
Thank Richk,
Still no luck. Here is the output from execmgr.log. Its saying that is completed but nothing ever happens. I am about ready to throw in the towel on this one but I just feel like that is should work because its such a simple script.
Set WshNetwork = CreateObject("WScript.Network")
WshNetwork.AddWindowsPrinterConnection "\\srv-gtt-papercut\followme"
WshNetwork.SetDefaultPrinter "\\srv-gtt-papercut\followme"
Phil Balderos
Is the script running as an Admin ,if so then you likely set the printer up for the local system user account and not anyone else.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ

Fasten the Process of MDT UDI OD Installation in SCCM 2012 R2 OSD

Hi,
I have implemented MDT UDI Task Sequence in SCCM 2012 R2 OSD. The issue which I am facing is the UDI Installation progress is very slow. it is taking around 2 hours to complete the whole Installation.
Is there any way to fasten the Process of MDT UDI OD Installation in SCCM 2012 R2 OSD.
Thanks & Regards,
Sanjay Dubey

Application installs can take awhile - it depends on what applications you're installing, and how many. For instance, installing Office is clearly going to take longer than say 7-Zip. How many applications are you installing during a normal OS
deployment? You can check the AppEnforce.log to see how long an application(s) is taking to install, as the start and end times are recorded.
As for the MDT Settings package, how many times are you calling this package? My task sequence only calls it 5 times, and one of them is before you even get the UDI wizard, while the second and third is an either/or situation, depending on whether
you do a refresh or a fresh PC build.

Deploy Lync 2013 Via SCCM 2012

Dear,
I wants to deploy Microsoft Lync 2013 via SCCM 2012, I have created a new deployment package based on MSI file to install Microsoft Lync 2013 for company machines, during the installation package will install for clients computer perfectly but instead of
install automatically to users, every time message coming user should do it manually for example user should accept the terms of the agreement, kindly I need a way to solve this issue, I need Lync 2013 automatically install without users doing anything, please
see attached snapshot.

Make sure that you are using the right command line using your newly created MSP
ex: setup.exe /adminfile "Lync_Updated.msp"
As proposed, update your DP so that your MSP gets distributed.
You can also follow this guide if you're still experiencing difficulties.
http://systemcentersynergy.com/lync-2013-silent-or-unattended-install/
Benoit Lecours | Blog: System Center Dudes

Lync 2013 client deployment via SCCM 2012 forcing restart

All,
I am attempting to deploy the Lync 2013 x86 client via SCCM 2012 to 158 machines running the Office 2010 suite. My package runs, and the installs complete but they are forcing a restart after the install even though I have gone in to everything that I can
think of to tell the install not to force a restart. I am a newb in the ways of SCCM so I have been self teaching, and I may have missed something.
I have gone into the config.xml and changed the value SETUP_REBOOT to NEVER.
In the program properties I have RUN set as HIDDEN, and AFTER RUNNING set to NO ACTION REQUIRED.
Is there something that I am missing to stop the users machine from restarting after the install completes?

Great, unfortunately it will be because files (usually shared DLLs) are in use as Office is opened, despite it being an older version.
Agree it's not optimal, I usually just tell clients that they will need to reboot, or that it will push out overnight (when I schedule it) and their computer will restart, so make sure they save everything.
If this helped you please click "Vote As Helpful" if it answered your question please click "Mark As Answer"
Georg Thomas | Lync MVP
Blog www.lynced.com.au | Twitter
@georgathomas
Lync Edge Port Check (Beta)

Trouble Deploying Windows updates via SCCM 2012

Hello
I'm testing Windows updates via SCCM 2012 - I have successfully deployed updates to 4 test PC's.
I then added another 15 Test PC's into the same group - Not one of them receive updates (they're all within the same Domain and even in the same room)
I reviewed "UpdatesDeployment.log -
1. I highlighted some points that stood out to me
2. I have the Maintenance window set to 24hours for this test
From the Server side and Clients side - What are the best .logs to look at.
CUpdateAssignmentsManager received a SERVICEWINDOWEVENT START Event   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
Suspend activity in presentation mode is selected   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
At least one user has elected to suspend non-business hours activity when in presentation mode. Checking for presentation mode.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
Proceeding to non-business hours activites as presentation mode is off.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
Auto install during non-business hours is disabled or never set, selecting only scheduled updates.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
A user-defined service window(non-business hours) is available. We will attempt to install any scheduled updates.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
Attempting to install 0 updates   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
No actionable updates for install task. No attempt required.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)
Updates could not be installed at this time. Waiting for the next maintenance window.   UpdatesDeploymentAgent   22/08/2014 10:00:00 PM   4604 (0x11FC)

Hi,
You could also check Windowsupdate.log on the client.
Best Regards,
Joyce
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to deploy MS Visio & MS Project via SCCM 2012

Dear friend,
Please let me know the How to deploy MS Visio & MS Project via SCCM 2012, step by step
Thanks

You need to utilize Office Customize Tooltik to build config.xml, then distribute the config.xml with setup file. Below are some documents talking about this.
http://blogs.msdn.com/b/visio/archive/2011/02/04/more-on-visio-2010-volume-deployment.aspx
http://blogs.technet.com/b/odsupport/archive/2010/12/03/volume-license-editions-of-visio-2010-install-premium-edition-by-default.aspx
Juke Chou
TechNet Community Support

SCCM 2012 CU2 OSD forest trust: ReleaseRequest failed with error code 0x87d00317

Hello,
Actually i have a difficult Problem with my SCCM 2012 R2 CU2 Windows 7 x64 SP1 Tasksequence:
I get the folowing error in smsts.log:
::RegQueryValueExW(hSubKey, szReg, NULL, NULL, NULL, &dwSize), HRESULT=80070002 (e:\qfe\nts\sms\framework\tscore\utils.cpp,811) TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
RegQueryValueExW is unsuccessful for Software\Microsoft\SMS\Task Sequence, SMSTSEndProgram TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
GetTsRegValue() is unsuccessful. 0x80070002. TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
End program: TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Finalize logging request ignored from process 1736 TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Waiting for CcmExec service to be fully operational TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
CcmExec service is up and fully operational TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Access handle will be read from _SMSTSActiveRequestHandle TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Access handle: {B699D570-B2BF-4874-8CB7-3B208B380969} TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Attempting to release request using {B699D570-B2BF-4874-8CB7-3B208B380969} TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
CoCreateInstance succeeded TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
pISoftwareExecutionRequestMgr->ReleaseRequest(ActiveRequestGUID), HRESULT=87d00317 (e:\nts_sccm_release\sms\client\tasksequence\tsmanager\tsmanagerutils.cpp,136) TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
ReleaseRequest failed with error code 0x87d00317 TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Task Sequence Manager could not release active TS request. code 87D00317 TSManager 9/5/2014 1:20:35 PM 1740 (0x06CC)
Here is the complete smsts.log: http://1drv.ms/1pwTEBf
To explain the Problem in Detail:
The SCCM Primary Site Server and the Clients are in different trusted (bidirectional) forests!
Everythings working fine in this Scenario, I can install SCCM Agent on the Clients with Manual ccmsetup and with Client Push Installation. Additionally i can deploy Software Updates and so on... only OSD is crashing in the releaserequest step.
During my Tasksequence new Clients are joined to Domain A while SCCM Primary Site Server is installed in Domain B
If I change my TS and let the Clients also join Domain B everything works without any Problems and the Tasksequence finish without any Errors.
My Problem must be related to the different Domains and the forest trust.
My Setup:
MP published to DNS in both domains
Schema Extended in both domains
System Management Container published and verified in both domains
ccmsetup Parameters in TS: ccmsetup SMSMP=sccm.domain.b FSP=sccm.domain.b DNSSUFFIX=Domain.b
Network Access account configured with Domain B account
Domain Join account has create Computer rights on the OU in Domain A (Domain join is successful)
DNs conditional forwarders configured in both Domains and DNS resolutin is working in both directions
Any suggestions?
Many thanks.
regards,
Christian

Hi Christian,
So do you actual get an error message in your TS or is it just failing to join Domain B? (Could be both if the machines fails to join the domain).
Can you review netsetup.log on the machines after the issue and see what error message you might be getting during the domain join process?
Also, if it a domain join issue, can you try manually joining to domain B using the same service account?

Lenonvo T440 with Intel SSD SC2BF240A4L - failing to install apps via SCCM 2012 task sequence

Hi there
Wondering if anyone else has encountered this issue with a T440 with Intel SSD hard disk.
Our firm purchased two Lenovo T440 laptops. One has a magnetic hard disk, the other a SSD hard disk. Here are the models:
SSD hard disk: Intel SSDSC2BF240A4L
Magnetic hard disk: 500Gb 7200rpm HTS725050A7E635
We deploy our Windows 7 build via a SCCM 2012 task sequence.
Building the T440 with the magnetic hard disk was trouble free. I built it repeatedly, and encountered no errors; our core applications installed successfully every time and the task sequence completed successfully every time.
All well and good.
Building the T440 with the Intel SSD hard disk has been frustrating. When I run the task sequence on this machine, 8 times out of 10 the task sequence will fail, either stopping abruplty at installing Oracle Single-Sign On or Appsense agents. When the task sequence fails it is ALWAYS at one of these two apps.
Frustratingly, sometimes the task sequence will complete successfully on this T440.
Given we successfully deploy this task sequence to a variety of different hardware from different vendors, including other Lenovo laptops, I can only guess the Intel SSD hard disk is the culprit.
Has anyone encountred anything like this? I've went through the smsts.log file and other SCCM log files and can find nothing obvious. That this ONLY happens on the T440 with the SSD suggests to me the issues lies in that direction.
I'll swap disks in either T440 to see if the other T440 fails also with the SSD aboard, to see what happens.
Meantime if anyone has any information about this issue I'd be grateful if you coud share.
Thanks
CT

Does the install provide any logging? Does execmgr.log show any other info?
Per the readme, it should be setup.exe.
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/girc15ww.txt
Unattended Install
This is for system administrators' use only.
1. Refer to the Manual Install section, and download and extract the file.
2. In the step 11 of the Installing files section, uncheck the checkbox next
to "Install ..... now", and then select Finish to cancel installation.
3. At the command line, execute Setup.exe with the -s option.
Example: [Path where the files were extracted]\Setup -s
Daniel Ratliff | http://www.PotentEngineer.com

SCCM 2012 SP1 OSD in 802.1X environment

Dears,
we have SCCM 2012 SP1 CU5, and the network team has enabled the CISCO port security (802.1X network authentication) on the desktops VLAN and OSD is not working since then until port security is removed. i've seen some guides regarding how to make SCCM 2007
OSD, WinPE 3.0 and 802.1X work together like : http://myitforum.com/cs2/blogs/lakey81/archive/2011/07/06/configuring-802-1x-network-authentication-for-winpe-3-0-and-configmgr-deployments.aspx , but ot's very confusing.
does anybody have the same scenario with SCCM 2012, WinPE 5.0, and 802.1X . please help me.

Hello,
What confused you here? 802.1X authentication is to authenticate before sending network packages. That is why we need import netwrok profile to win pe for anthentication. The point is authenticate, so I think it won't be any difference between
ConfigMgr 2012 and 2007.
Another good article here:
http://blogs.technet.com/b/deploymentguys/archive/2010/03/02/adding-support-for-802-1x-to-winpe.aspx
Please also pay attention to the shared document in the blog.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

IE11 prereqs deploy via SCCM 2012

Hi,
To deploy IE 11 on Windows 7, apparently you need to install 9 prereqs (see http://www.itninja.com/blog/view/how-to-package-internet-explorer-11-x64-for-windows-7-x64):
These prereqs are: KB2834140
KB2670838 KB2639308 KB2533623 KB2731771
KB2729094 KB2786081 KB2888049 KB2882822
I don't find the prereqs in red within sccm 2012. Did check the classifications (checked them all in software update point) and did a full sync.
Please advise howto find/deploy them (I hoped to do this via windows updates and not via seperate packages).
J.
Jan Hoedt

Hi,
I just checked the first Patch:
http://support.microsoft.com/kb/2670838
And there you can find the section: How to obtain this update.
Is there is Windows Update not noted, you can't receive this Patch through Windows Updates. Consider to deploy the Patch as prerequisite as an application. Here you can find an example of installing hotfixes as prerequisite for the App-V client:
http://scug.be/sccm/category/detection-methods/
Detection method is VBScript. Ar you want to create a Detection method with Powershell, refer to this blog post:
https://sccmfaq.wordpress.com/2013/03/19/sccm-2012-application-detection-with-powershell-and-code-signing/
Hope this helps.
www.sccmfaq.ch

Latitude E6330 BSOD via SCCM 2012 R2 OSD

Similar Messages

Maybe you are looking for