LCD off after OS 10.3.1

On my Z30 I did the OTA (Rogers) on Feb 19, 8 PM and was able to use 10.3.1 until I left
the device charging overnight and then it bricked.
Display was off and and all I get after numerous resets was periodic red LED pulsing. I used Link to try and update and it would start and then say device update not complete. So then i tried to use Link to go back
to factory default load. same issue. I then used an autoloader to 10.2.1 and same problem
then autoloader to 10.3.1.1581 and still no luck.
summary of steps:
1) hard reset by holding top switch down for 30s
2) made sure fully charged
3) connected to PC and saw that device manager recognises the device.
4) windows explorer sees the SD card and onboard memory
5) In Link tried SW update to latest version and also back to factory
***these didn't appear to complete (in hindsight because the device prompts onscreen probably to complete
the set-up but I couldn't see the screen!
6) from crackberry forums was able to find and run autoloader to an older version of the OS
and then to most recent version (10.3.1.1581). Same problem as before no screen.
7) Determined the issue is the LCD display by hooking up HDMI cable to TV and indeed the device is fine and using settings/about I could see the following SW is loaded:
10.3.1.1581 SW
10.3.1.2267 OS
10.3.1.2268 radio
So the device is fine, except the LCD. I have had 0 issues with my Z30 till this OS upgrade.

Using HDMI to TV i was able to launch and run BB Virtual Expert.
The LCD touch tests pass
All colour tests pass, mind you this is HDMI output to the TV.
all other tests pass (I skipped some because it's so annoying navigating via TV).

Similar Messages

Update: Video - Canon 6D turns itself off after a few shots with fully charged battery

Update: I uploaded my video to youtube, please comment:
http://youtu.be/3PNLUYd8g7A
TIA and pardon me for my English.
I posted this originally at another forum, and somebody suggested me to post it here as well, to get more help.
Long story short, I purchased a brand new Canon 6D from B&H on Oct 24th, 2013. From early december, the camera starts to shut itself off randomly and displaying empty battery. I found the camera constantly shuts itself off after 20 - 100 continuous shots with a FULLY charged battery (right off charger, showing 8.23V using multimeter, and showing 98% in battery info).
The camera will just turn itself off in the middle of shooting, showing empty battery int the shoulder window. The solution is simple, open the battery door, then close it again, no need even to pull the battery.
So, I contacted Canon support, sent the camera to the VA service facility, waiting for it be repaired. As an engineer myself, I understand things fail, and I thought this is such an easy issue to reproduce, anybody should be able to repro it.
Couple of days later, I received a phone call to send my accessories in, no problem, debugging needs more info, that's normal. I sent my lens and stuff in. I unfortunately had to bear the cruel fact that I don't have a decent camera for the holiday, though I have a backup.
After a long wait, on 12/28the, the accessories were delivered at 9:35am. At 10am, they called me, they were sending the camera back. No issue at all. I was like, have you tested AT ALL? They didn't care, sending the camera back regardless.
I received the camera on Jan 2nd, and saw the same issue on that day. Of course, it was NOT fixed at all.
I googled really hard, somebody said he had similar issue but it was a defective battery, so I got a brand new Canon battery, unfortunately, the same issue pops up again.
Ok, the only choice for me is to send it back again. But this time I am totally amazed by Canon.
I sent the camera in again with my lens and battery. Also, a video showing the issue on a standalone CF card (I know 6D does not take CF, just to put the video on it).
Couples of days later, they called asking for accessories, I was like, what accessories, I don't have any more.
Then the camera sit in their facility for a few days for nothing. All of sudden I received a phone call on Monday morning, said it is ready. The camera has no issue at all.
I called, asked whether they have watched the video, they told me two technicians, including a senior one, was not able to upload the video to the computer. I was like, what the hell? why the heck you need to upload it to the computer, find a card reader, plug the card in, double click, how simple is that?
I talked to the service manager over the phone, he told me that there is nothing he could do, if their technician said so. They have decided to send my camera back, NOT fixed, again. I esclated the issue again, but haven't heard anything back yet.
Honestly, I am totally pissed, how stupid can they be? I included a letter with detailed steps on how to reproduce this issue. As an engineer myself, I know how easy to reproduce this issue. But what shocked me is that they don't even know or they didn't even bother to watch the video. In the same letter, I asked/begged them to contact me if they cannot reproduce the issue instead of just sending it back unfixed.
Guys, any other ways to get their attention? I already filed a BBB complaint. For a brand new camera of 3 months old, it has been in Canon's repair shop for almost a month. Leave to say that I missed the most importand holiday season in the year. This is simply not acceptable.

"The camera usually shuts itself off after 20-100 continuous shot, ..."
By this you mean your are in continuous drive? You just hold the shutter release down until it stops shooting?
"... the shoulder LCD shows a ..."
What is the "shoulder" LCD?
Sorry for the extra questions but I am trying to understand exactly what you are going through and why Canon said it is OK.
Canon did not say it was all right if it is not.
You are, also saying, if you use the camera, just for a single snap shot, say several in a session, it is OK? Right?
It only shuts down when on continuous drive or video?
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 8.7, Lightroom 5.7

My apple calendar shuts off after a second on some days not others

My google calendar turns off after a second on some days and not others

Hello JPhardboiled,
To save battery power, the camera turns off automatically after 1 minute of non-operation. To turn on the camera again, just press the shutter button halfway.You can change the auto power-off time with [: Auto power off] Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons.1 Select [Auto power off]. Under the [] tab, select [Auto power off], then press <>.2 Set the desired time. Select the desired setting, then press <>.
Even if [Disable] is set, the LCD monitor will turn off automatically after 30 min. to save power. (The camera’s power does not turn off.)

My iphone wont turn on but when i plug it in to charge the apple logo comes on and turns back off after a few seconds i dont know what to do i need help

my iphone wont turn on but when i plug it in to charge the apple logo comes on and turns back off after a few seconds i dont know what to do i need help

Hello warhogs17,
After reviewing your post, it sounds like the iPhone will not turn on past the Apple logo. I would recommend that you read this article, it may be able to help the issue.
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Why does audio in Tremolo and Legato mode cut off after 3 or 4 seconds???

Question regarding the symphony orchestra section when it comes to bass, string, cello, viola in Tremolo and Legato modes: why does the sound cut off after 3 seconds.
Let's say you have Viola, Tremolo section selected, how do you make the sound not cut off after 3 seconds. What if you want it lasting 6 or 7 seconds???
Can you override that limitation???
Thanks very much in advance,
- Nicholas

Most likely a network issue. Power cycle the router.
Disable any firewall on the computer, if issue is using AirPlay from a computer.
Ensure the router is running the most current firmware.
If the ATV is connected via Wi-Fi, try ethernet.
Change the Wi-Fi channel if ethernet is not an option.

IPod Nano (4th Generation) switches on when connected to USB power - shows Menu & hangs (unresponsive to click wheel) - deems off after 5-sec - Switches off after disconnecting from USB Power - syncs with iTunes - Tried 5R's - Problem still persists

1. The iPod Nano (4th Generation - 8GB) switches on, only when connected to USB power by showing apple logo and displays Menu options thereafter..
2. However, I can not access Menu as it is unresponsive to click wheel. As a result it is inaccessible to any further use,
3. NOTE: it displays "Battery Fully charged" icon on the screen without any "Lock" icon.
4. After 5-sec to 10-secs the screen deems off.. i.e. goes to sleep mode.. And thereafter would probably remain like that (sleeeping) for eternity!!!!
5. It Switches off after WITHOUT DISPLAYING any Apple Logo immediately after disconnecting from USB Power.
6. In other words, it can be switched on only through USB power in spite of battery being fully charged.
7. Interestingly, it syncs with iTunes. It is recognised in iTunes (Latest version 11+).. Displays on screen all commands Like.. syncronising, connecting, connected,
8. Allows to add Music, videos like a normal ipod & displays all status information in iTunes.
9. Read Trobleshooting & Tried all 5R's. Registered, Resetted, updated & Restored to iOS 1.0.2
10. It is now displaying to select Language in place of Menu options, with no access through click wheel, centre button whatsoever... Problem still persists
KINDLY GUIDE ME THE SOLUTION. APPRECIATE YOUR RESPONSE in advance...

"I get the feeling that this is a software issue that could probably be solved quite easily"
Since you have already tried all the normal troubleshooting solutions, take the iPod to your nearest Apple Store for a *proper diagnosis.* The staff there will be able to confirm if your problem is software or hardware _*at no cost to you.*_
!http://i50.tinypic.com/izvwo1.gif!

15-r007TU-Display does not turn on when it automatically turns off after closing lid.

I just purchased hp 15-r007TU, Windows 8.1 x84. I'm facing a strange problem. After all initial setup, I put the laptop on to download and install all lates Windows 8.1 patches. The display is set to tuen off automaticaaly after 5 minutes. After 5 min it did turn off as set. But then I can not turn it back on. I pressed all (except power) keys, used touch pad, closed lid and opened but it stayed off. Laptop was on and running as I could see HDD lights flickering, I could hear system sounds on pressign mute/volume keys, also I could toggle WiFi with key. I then pressed power off key to turn Windows off normally. I did turn off. I again turned it on, I could see 'hp' logo with spinning wheel and then nothing. Display is off and I don't see start screen. I have to hard reset (press power button for more than 5 seconds) then display is normal. This happens every time the display turns itself off automatically after set time or I close the lid. Only after hard reset it works normally and I see the start menu.
The power settings I use are:
1. never put system to standby after preset time. (either on battery or AC power)
2. turn display off after 5 min. (both on battery or AC power)
3. when I close lid - do nothing. (both on battery or AC power)
4. when I press power button - shut down
I am using Windows 8.1 x64 with all latest patches installed. BIOS updated to lates available. All latest drivers installed.
I have not yet set password to the system to log in.
Help would be immensly appreciate. The device is still in warrenty if it needs to be replaced.

Hello K1200LT,
Welcome to the HP Forums!
I understand the computer will not sleep when you shut down the lid. You seem to have already done most of the troubleshooting I would've suggested.
To be honest, it is either a hardware or software-related issue. To determine this, I would like you to reinstall the operating system. It will clear up any software conflicts and allow you to start fresh.
First, please ensure you backup your files. Here is information on how to do this: Backing Up Your Files (Windows 8)
Once this is done, it is safe to reinstall the operating system. Performing an HP System Recovery (Windows 8)
If the same situation occurs, the computer likely has faulty hardware. At that point, please contact HP phone support. You can utilize this website to learn how to contact HP appropriately, based on your region: Contact HP Worldwide
Please let me know what happens. Thanks!
Mario
I worked on behalf of HP.

Macbook Pro shuts off after few seconds of gray screen

Help - I came home to discover my power cord had died and my laptop turned off due to no power. I used a friend's power cord to turn it on later that night and send some emails. I bought a new power cord the next day, plugged in, and turned the laptop on. It stayed on the gray screen with a spinning wheel beneath the apple logo for a while. I restarted it and it turned off after a few seconds of the gray screen. An empty bar flashes twice horizontally at the bottom before the spinning bar begins.
I tried booting in safe mode, but it would just stay on the gray screen. I tried doing shift+command+v and received a message about keys out of order and disk error full, can't repair. I was able to boot from the install disc, and when I click "Repair Disc" I get the same erros. Not sure what to do now?

Migg7 wrote:
Would my time machine data be preserved with this?
Well this is the big gamble. You really don't know for sure.
TimeMachine has gotten corrupted from a failing original drive and then unable to restore properly to a new drive.
It's not like you can access the files on a TM drive directly and cherry pick what you need and leave the rest. It's all or nothing.
If you go erasing your only other copy on the boot drive, which the files still could be accessed from another boot drive, and if you find out the TimeMachine drive can't restore, then your up the creek without a paddle right?
So if your able, create a data recovery drive and try to rescue your second copy of the files on the boot drive or restore the TM drive to the second boot drive , so this way your files can be accessed directly if you need it and you have two copies again.
Once you can direclty access your files then you can go about erasing and installing on the internal boot drive.

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the b.u. stops

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the backup stops. The system preferences are set to "Never" for Computer sleep and Display sleep. The computer does not ordinarily log off automatically, but it has done this twice since I started the Time Machine backup.

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If all you see are messages that contain the word "Starting," you didn't clear the search box.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting.

Yoga display turns off after 1 minute

I'm having an annoying problem with my new Yoga related to the display and have not seen any other posts with a similar complaint so perhaps this is a simple fix that I'm just not able to sort out on my own. My display turns off after 1 minute of inactivity. The only means for changing behavior like this that I am aware of is through the Control Panel Power Options. My settings for "turn off the display" are 10 minutes on battery and Never while plugged in (note screen shot attached). Regardless of my settings, the screen turns off after 1 minute. I've changed the settings to multiple configurations and restarted with no change in behavior. Perhaps there's some other settings area, maybe something specific to Lenovo that I'm not aware of (since this is my first Lenovo laptop). Anyone with similar problems or insight?

This may be a Windows 8 issue. I finally fixed this problem by identifying the screen saver as the issue (and I wasn't using a screen saver). Type "lock the computer" into the search box after clicking the search charm, which brings up the screen saver dialog box. Mine was set to 1 minute, though I'd never set it myself. If you can't change it, choose a screen saver and you should be able to do so (and can then switch back to no screen saver). BUT, here's the problem. Other things you install (or settings within things you install) can apparently change and override whatever you type in for the delay time. Try applying your new time and exiting from the dialog box, then open it back up again. I was finding that it kept going back to 1 minute. To reset things so that you can get control again, type "user accounts" into the search box and when the dialog box comes up, choose "Reset Security Policies". Then you can go back to the screen saver dialog and successfully change the delay time. See http://social.technet.microsoft.com/Forums/windows/en-us/ace4085a-b0ba-4a98-898d-cd92d9e88e13/window... for some detail.

Sound cuts off after 1 minute. Wireless HPs Model: TMR-RF985R

I replied to a topic regarding the same issue, but will make a thread about it as the problem is urgent (I need noise cancelling sound for a symptom I suffer from) and of course I use these headphones almost 24/7 as my work/lifestyle relies heavily on them.
THey were working fine for roughly ~ 2 years until recently when I started noticing that they shut off after some use. I used to think it was the batteries, but I charge them for 15 hours every night just as I always have, so that can't be it. Everything is plugged in. I've lurked over threads discussing the same problems all over the net and applied all their inputs to no avail.
Any help is MUCH appreciated - any help that would actually work! My gut says these headphones are on their way to the grave.
Thanks in advance
Solved!
Go to Solution.

Argh now I'm ransacking the entire internet to figure out how I'm supposed to get to the batteries on these headphones. Any help would be appreciated... (I know it's quite a newbish question, but what the he11, given the stealth on this thing!)
UPDATE: I guess there is no option to replace the batteries without sending it over to the manufacturer??? That's kinda imprudent IMO but maybe I'm missing something (?). So I have to pay an additional fee including shipping for something that I should be able to do free of charge minus expenditure on batteries.

My screen darkens after 1 minute and turns off after 3. All of a sudden, now, after the screen shuts down, it comes right back on????

My screen darkens after 1 minute and then turn off after 3 minutes (energy saver). Now, all of a sudden, after it shuts down it comes right on???

thank you so much sir... i am very thank ful to u... it was an breath taking moment ... i was almost dead as it didnt work

My radio cuts off after about 5 min. It didn't do this until the last update. How do I fix this?

After the most recent upgrade on my IPhone I can no longer keep listening to my radio. It cuts off after about 5 min. I used to also be able to lock my screen and have my radio or music keep playing but now it shuts off when locking my phone. How do I fix this - it's very annoying to be running and have to stop every 5 min. to turn the **** radio back on.

Push the headphone jack in farther, the plasic on the headsit jack must be flush with the body of the Nano.

Screen turns off after a few minutes and needs to be closed then opened

hi, as the title suggests my powerbook screen turns off after a few minutes before my screensaver is set to come on and when i come back and press a key or move the pad it wont start up so i need to close the powerbook then open it up again for it to activate. its not a huge problem but my programs which connect to the internet seem to lose their connection when i open it up again. is this normal? is there a setting i can change?
thanks
ross

Is there a way to "disable" Standby, Suspend and Off just when watching movies (in fullscreen or not)? I want them to do what they usually do in all other cases.
Setting them to 0 in xorg.conf does the thing, but I need that functionality only when I'm wathing movies. Making a script that alters adjustments in xorg.conf isn't the best solution - you'd have to restart X every time you want to watch a movie .
Cheers,
Daniel

My iPad does not automatically shut off after several minutes of non use. I can shut it off with the on/off switch. What can I do to get the auto sut off feature back?

My IPad does not automatically shut off after several minutes of non use as it had been doing a few days ago How can I restore this auto feature?

Settings>General>Auto-Lock and select an Auto-Lock time (the "Never" setting will of course never auto-lock the device)

LCD off after OS 10.3.1

Similar Messages

Maybe you are looking for