LDAP on Cisco SPA514G ip phone

Hello I am having issues setting up LDAP on our SPA1514G phones.
I completed the setup in the we configuration utility, but cannot see the LDAP directory on the phone display.
Is there something I am missing?
Thanks!

You probably want to ask/move this to the SMB community.

Similar Messages

Cisco SPA514g Secure web interface only.

I have a Cisco SPA514g, I want to secure the web interface with a password. When I change the password and it reboots the phone comes up fine. On certain functions in now asks for the user password for example on redial. Is there a way to disable the security on these functions other than removing the password on the profile "user"?

Use the following document http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1100/accsspts/i12213ja/i12213sc/s13web.htm to get access to the Web interface

Using Cisco wireless IP phones in Cisco Call Manager 5.1

Hello,
Currently we are using Cisco CallManager ver.5.1.2.3000-2, Berbee InformaCast ver.6.1.1 and Cisco Unity 1.1 Build 10. We like to replace few Cisco IP Phone 7961G-GE with Cisco Unified Wireless IP Phone 7920 ver.3.0. Does CCM ver. 5.1.2 supports Wireless phones? If it does, how do I configure it? Also, do I have to purchase any new license or other hardware?
Any suggestion / recommendations greatly appreciate.
Alex

Yes, it does:
Cisco Unified IP Phone Series 7900
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr.html#wp51474
Config on CUCM itself is no different from any other phones neither other requirements like DLUs.
Of course you should already have APs for connectivity.
HTH
java
if this helps, please rate

Cisco 7821 IP Phone not registered in CUCM 9.1.2

Dear all,
We have CUCM 9.1.2.11900-12 and we have uploaded this device package: cmterm-devicepack9.1.2.12028-1.cop.sgn and reboot cluster
But the Cisco 7821 IP phone not registered in CUCM
can some one advise me?
Thanks and best regards,
Tan

Hi
Can you please share the output for show version active from CUCM.
Please check the following thread as well:
https://supportforums.cisco.com/discussion/12030206/adding-7800-phones-cucm-8691

Cisco 7925 Wireless Phone Wireless Auto Config

Hello all,
My rehabilitation hospital is located right next to a large hospital connected by a catwalk. We have had 3 incidents where our RTs have gone over to the hospital next door for patient MRIs and our Cisco 7925 wireless phones are being configured with that hospitals wireless profile. The RTs are saying that no one from that hospital are manually configuring the phones to be on their wireless network so they can be used while off our wireless network. We're thinking that the RTs are putting their phones down and picking up the other hospitals 7925s by accident before leaving. My question to you is...Does the Cisco 7925s have an auto configuration tool that will automatically pick up on a particular wireless network and automatically configure itself and register with a Call Manager? Thanks!
Regards,
Terence

Leo and George,
Exactly! It makes absolutely no sense. All our Cisco 7925 phones are manually configured for our voice VLAN for our wireless network infrastructure. It's the only profile I've configured for those phones. I spoke to the other hospitals IT personnel and was advised that they use a wavelink server that sends the configuration to their 7925s after they have been entered into the server. The only explanation I can come up with is that our RTs are sitting our phones down, doing whatever they need to do over at the hospital, then picking up the hospitals 7925 thinking they're picking up ours. Another thing to note is that when I reconfigured the phone to be put back on our wireless, the phone performed a firmware update and then registered to our Call Manager.

Question about Cisco 7940 ip phones

I always have the same problem with Cisco 7940 ip phones.
I only have direct access to one speed dial with the button near of the screen and I think that it isn't good because to get access to the rest speed dials I must to use short dials and I must to have it written in a paper to remember the number where I have each speed dial.
Is there any way to solve this problem?.
I use CCM 4.1.
Thanks, Carlos.

7914 should supports with 7940, 7960 and 7970. But in CCM4.1, I couldnt add phone button under 7940. I guess 7940 no longer suppot 7914.
After CCM 4.0, you have to create phone button template. For example, if you have one 7914 which has 14 buttons, then you have to create phone button template with additional buttons.
Under phone device, you can pick the new phone button template, and then select "Expansion Module Information" 7914 module.
Thanks
Please rate helpful post.
Ken

Cisco 7912 IP phone

HIii..
can any one tell me , hw to use the ip phone without handreceiver , i mean hw to use speaker/mic of phone..
Is there any setting before to use it ?
if so plz tell me
Thanx...

Hi Manoj,
Unfortunately the 7912 does not have a "built-in" mic, so the speaker is listen only. Have a look at the following excerpt;
The Cisco Unified IP Phone 7912G is designed to grow with system capabilities. Features will keep pace with new changes via software updates to the phone Flash memory. Examples of currently available features include:
Support of a single line or directory number
Calling name and number display
Call waiting
Call forward
Call transfer
Support of Extension Mobility
Three-way calling (conference)
On-hook dialing, predialing, and off-hook dialing
Redial
Call hold
***Call monitor (speaker only, no microphone)***
"Messages" soft key that allows access to voicemail messages
Four speed dials configurable at the Cisco Unified CallManager
From this 7912 data sheet;
http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet09186a00801739c0.html
Hope this helps!
Rob
Please remember to rate helpful posts.....

Cisco sip ip phone CP-7841 couldn't registered in cisco CME SRST 2951

Hello,
My IP phone CP-7841 couldn't registered in my call manager. Can you help me please?
See the configuration below:
yourname#sh run
Building configuration...
Current configuration : 7013 bytes
! Last configuration change at 17:52:57 UTC Mon May 4 2015
version 15.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname yourname
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
aaa session-id common
ip dhcp excluded-address 192.168.2.1
ip dhcp excluded-address 158.113.41.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool voice
network 192.168.2.0 255.255.255.0
default-router 192.168.2.1
option 150 ip 192.168.2.1
lease 0 2
ip dhcp pool data
network 158.113.41.0 255.255.255.128
default-router 158.113.41.1
lease 0 2
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server expires max 1200 min 300
voice register pool-type 1
description Cisco IP phone 7841
reference-pooltype 6941
voice register global
mode cme
source-address 192.168.2.1 port 5060
max-dn 400
max-pool 150
load 7841 sip78xx.10-1-1SR1-4.loads
load 7861 sip78xx.10-1-1SR1-4.loads
authenticate register
authenticate realm all
tftp-path flash:
file text
create profile sync 0002065003436039
voice register dn 1
number 101
name phone 1
voice register dn 2
number 102
voice register pool 1
busy-trigger-per-button 2
id mac E0D1.73E4.0C58
type 7841
number 1 dn 1
voice register pool 2
busy-trigger-per-button 2
id mac E0D1.73E4.A54C
type 7861
number 1 dn 2
license udi pid CISCO2951/K9 sn FCZ185070TS
hw-module pvdm 0/0
username unicef privilege 15 secret 5 $1$pCbf$7NtwVixNLu1vbwJJLRTN5.
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 10.10.10.1 255.255.255.248
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.10
description router interface for voice vlan
encapsulation dot1Q 10
ip address 192.168.2.1 255.255.255.0
interface GigabitEthernet0/1.50
description router interface for data vlan
encapsulation dot1Q 50
ip address 158.113.41.1 255.255.255.0
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
nls resp-timeout 1
cpd cr-id 1
tftp-server flash:rootfs78xx.10-1-1SR1-4.sbn
tftp-server flash:sboot78xx.10-1-1SR1-4.sbn
tftp-server flash:sip78xx.10-1-1SR1-4.loads
access-list 23 permit 10.10.10.0 0.0.0.7
control-plane
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
mgcp profile default
gatekeeper
shutdown
telephony-service
max-conferences 8 gain -6
transfer-system full-consult
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you want to
use.
^C
banner login ^C
Cisco Configuration Professional (Cisco CP) is installed on this device.
This feature requires the one-time use of the username "cisco" with the
password "cisco". These default credentials have a privilege level of 15.
YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
CREDENTIALS
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want
to use.
IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
For more information about Cisco CP please follow the instructions in the
QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
^C
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
scheduler allocate 20000 1000
end

*****After looking at your config again, I see your "voice register pool-type 7841" had been added. I should have looked at the config a little closer.
Hello Akaffou Aristid,
The 7841 phone is a revision of the older 6941 phone and it needs to be referenced in the config.(Fast Track Configuration)
New SIP Phone models validated for CME using Fast-track configuration
voice register pool-type 7841
description Cisco IP Phone 7841
reference-pooltype 6941
"Once the new SIP phone model is configured using the fast-track configuration approach, the new phone model can be provisioned using the existing voice register pool configuration option as shown below."
Below is the link that references the above commands.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmebasic.html#pgfId-1295535
Hope this helps.
Please rate helpful posts.
Thanks.

Problem in Cisco Unified IP Phone 8961: How to register in Cisco Unified Communications Manager 7.1.(3)

Hi,
I am trying to register our 8961 Cisco IP Phone to register to the CUCM 7.1.3 but it doesn't seem to appear in the list of the phones supported. Upon further research, we found out that it is actually a SIP Phone. We tried registering it as a SIP Phone, however we cannot find any user/password field in the phone itself.
I hope anyone can help out.

You may need to download latest device pack for version 7.1.3:
cmterm-devicepack7.1.3.33031-1.cop.sgn
http://software.cisco.com/download/release.html?mdfid=282421166&flowid=5328&softwareid=282074299&release=7.1(5.36121)&relind=AVAILABLE&rellifecycle=&reltype=latest
HTH, please rate all useful posts!
Chris

Non cisco/Third party phones are compatible with CCX 9 or not?

Dear Guys,
I have a CCX 9 server integrated with CUCM 9 and also non cisco based/Third party phones (SNOM IP Phones) as agent for CCX server. when i try to log in to CAD software with User ID and password that assigned to SNOM phone i got JTAPI error but with CIPC(Cisco IP Communicator) works fine and i could log on without any issue. i checked RMuser controlled device and also allow controlled CTI port,all configured. i checked all documents about this issue but it is not mentioned anything about SNOM phone used as agent. any idea for that? any documents for compatibility list between CCX and agent platform...
i have checked below links
http://www.cisco.com/en/US/prod/collateral/voicesw/custcosw/ps5693/ps1844/prod_qas0900aecd80422e66.pdf
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf
Special thanks in advance for your help
Sara

Hi Sara,
If you do not see it in the UCCX comp matirx, than please remember that you will not get support from Cisco TAC incase if you hit any issues with this deployment.
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_compatibility/matrix/crscomtx.pdf
Thanks,
Anand

How to upgrade cisco 7940 ip phones

hi
i have cisco 2801 autocom with 7940 ip phones.
i wish top upgrade to the latest version but don't really know how i can do it.
please ask everything you need to know to solve the problem.
thanks a lot
reply to :
[email protected]

Do you mean upgrade the phone load? If yes, then try upgradign to the latest phone load that is 8.0.4 SR2 that can be found in the following link:
http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser
cmterm-7940-7960-sccp.8-0-4.exe
7940/7960 IP Phone load - Compatible CCM Versions: 3.3, 4.0, 4.1, 4.2
The installation instructions are in the Readme file in the same link:
When using Cisco CallManager Release 5.0 or later
For Cisco CallManager 5.0, you must do all software installations and upgrades by using the Software Upgrades menu options. The system can upload and process only software that Cisco Systems approved. You cannot install or use third-party or Windows-based software applications that you may have been using with a previous version of Cisco CallManager with Cisco CallManager 5.0.
Using your web browser, login to the Cisco IPT Platform Administration web page
Under the Software Upgrades menu, select Install/Upgrade.
Fill in the appropriate values in the Software Location section for the file you downloaded above, and click Next.
In the Available Software drop-down box, select the file you downloaded above, and click Next.
After validating the MD5 has the correct value, click Next.
In the Warning box, verify you have selected the correct firmware, then click Install.
Check that you received a Success message.
When Using Cisco CallManager earlier than Release 5.0
Login to the console of the CallManager Server where you downloaded the installer.
Note the location where you saved the downloaded file.
Double-click the file to start the installation.
In the Welcome window, click Next.
In the License Agreement window, click Yes.
If a Read Only File Detected window pops up, click Yes.
After the installation finishes, click OK.
Reset all corresponding devices.
Cisco IP Phone Model 7940/7960 Alternate Firmware format
The Cisco IP Phone Model 7940/7960 Firmware version 8.0(4) is also supplied in a zip file, as an alternative in case a Cisco CallManager is not available to run the executable installer program. The name of this file is cmterm-7940-7960-sccp.8-0-4.zip.
After unzipping the firmware files, they should be manually copied to the appropriate directory on the TFTP server.

DAP using LDAP and Cisco Attributes

I would like to be able to set up a Dynamic Access Policy with the criteria that if all of the following:
cisco.grouppolicy=Sales
ldap.memberOf=Remote_Access
can have specific set of access. My Connection profile is using a Radius server to authenticate and assign the Group Policy.
Is it possible to accomplish this? since it doesn't seem to work for me.

Hi Luis,
if you want to use LDAP attributes in your DAP policy, then you have to use LDAP for authentication or authorization in your tunnel-group.
So you will either have to replace radius with ldap for authentication, OR keep radius for authentication and add ldap for authorization on top.
hth
Herbert

Am I asking too much of the Cisco DX 650 phone?

At the beginning of the week, I had high hopes for the DX 650. I set up this device with the hopes that it would not be a Cius 2.0 device. However, when trying to setup some of the non-standard calling features, the device seems to bog down and become painful to use. Here is what I setup, or tired to setup:
External 24" monitor
Logitech C930 camera
Bluetooth wireless keyboard and mouse
Proximity via Bluetooth to my iPhone
VMWare Horizon client
I have to say, the Bluetooth connectivity is poor and clunky. The iPhone would not stay connected, and the DX 650 would rarely show my phone as a second device for calling. Contacts were synced sometimes, and if I left the room and came back, it would not connect again. In addition, having the Bluetooth keyboard and mouse were slow when everything was connected. The keyboard and mouse would connect, sometimes. Before anyone judges me, I am not using the WiFi at all.
The Horizon View client is OK, but when you are in a video call, it is horribly slow. I ultimately disconnected the Bluetooth and went back to a wired keyboard and mouse. I also disconnected the external Logitech camera. With all the other devices disconnected, the video calling and Horizon View client were usable, but not great.
If I reboot the phone, it is OK for a while.....
Am I asking too much of this device? It has potential, but how can I recommend this as an all-in-one solution to my customers? Will it get better? I still want to test the VPN connectivity on top of all I mentioned above, but I am afraid it will be disappointing at best....
Thanks
Jesse

hi Jesse,
have you tried the latest dx650 firmware? cmterm-dx650.10-2-2-23.cop.sgn
Cisco has done a huge improvement compared to old firmwares. I can understand your experience, but i was surprised, when i´ve done an upgrade the latest Software Version of the DX.
Best regards
Simo

WRT54GL & Cisco 7960G VoIP Phone

Hello fellow Cisco users,
I use a Cisco VoIP phone, the ubiquitous 7960G IP phone, and have no problem using it with non-Cisco routers. The phone does not seem to work with the Cisco WRT54GL router under the setup I have as explained below.
I usually connect my Cisco IP phone directly to my laptop's ethernet port giving the phone a shared internet connection. This arrangement works fine with two non-Cisco routers I've used. With the Cisco WRT54GL router however, the phone cannot get an IP configuration, even after opening the needed ports, leading me to believe the problem is likely to be something with the router. I have also tried setting up a DMZ for the router without success. The biggest problem is that the phone uses DHCP (which I also prefer) and the DMZ and port forwarding features require I set the phone's IP address.
I would greatly appreciate any thoughts on how to resolve this.
Many thanks for suggestions.
PS: I forgot to add that the phone works (i.e. receive and make calls) when plugged via ethernet cable into the router. Apart from the problem of having an ethernet cable running across a room, this setup also has some features missing like date and time so calls aren't stamped.

I think your phone is not getting IP address when it is connected to the computer. But when you connect it directly to the modem, it works.
You can try to upgrade/re-flash the firmware on your router.
Connect the computer with the Ethernet cable to the router.
Download the latest firmware from Linksys website and save it on your computer. Open the setup page of the router. Click on Administration tab and go to Firmware upgrade sub tab. Browse the firmware file that you have already downloaded and upgrade it on your router.
After upgrading the firmware on the router, it is recommended that you should reset the router and reconfigure it. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.
Also try to change some advanced wireless settings on the router. Click on Wireless tab and go to Advanced wireless settings. Change the Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.

Cisco 8941 IP phone background image

Dears,
I have cisco 8941 connected to CUCM 9.1, I tried to upload backgroung image unsuccesfully. where I already upload the background for cisco 7942 succesfully.
I already used (640x480x24) for cisco 8941.
Appreciate your support,
Regards

Hi
Are you sure from the below:-
1-Full-size image
640 pixels (width) x 480 pixels (height)
Thumbnail image
123 pixels (width) x 111 pixels (height)
2- Did you restart TFTF servers , if you have pub and sub ) . Upload for both TFTP and restart both.
3-disable and reenable the Enable Caching of Constant and Bin Files at Startup TFTP service parameter (located in the Advanced Service Parameters).
4- Tell us the path on your TFTP management is /Desktops/640x480x24/
5- Share also the firmware of your IP phone 8941 , is it 9.3 ?.
Thank you
Please rate all useful information

LDAP on Cisco SPA514G ip phone

Similar Messages

Maybe you are looking for