LDAP over SSL - Works with AD Username but not with full logon @

Hello
I have 2 Cisco ASA 5505 and have configured SSL over LDAP to connect via a Active Directory server.
Everything works fine apart that lets say I have a user called [email protected] - When I am using Anyconnect or Cisco VPN Client and try that it does not work at all.
If I try abc without the @zzz.com then it works and authenticates to the AD and gets DHCP and user is fine.
The only question is since I think I have seen this documented somewhere - is that correct or can I use the @ full AD UPN ??
I am trying to make our users do a single SSO and have every other application using the full UPN.
Thanks

Similar Messages

ITunes library stored on an external hard drive which is connected to my airport extreme, I wish to share my iTunes library over my network, I can do this with my laptop, but not with my iPad, can anyone tell me if it is possible

I have my iTunes library stored on an external hard drive which is connected to my airport extreme, I wish to share my iTunes library over my network, I can do this with my laptop, but not with my iPad, can anyone tell me if it is possible

You can't connect directly to the external drive, but should be able to use iTunes Home Sharing via the laptop.
http://support.apple.com/kb/PH1453

My firewire port works with ext hd but not with audio interface

2010 Imac 21.5 running 10.8.5. My firewire port works with ext hd but not with audio interface. The local authorized Apple tech said that I need a new motherboard, but my firewire ext drive works perfectly. I don't understand. Thanks.

You must go to the website of the audio interface manufacturer and look for, download and install updated drivers for the audio device you are using.
This is not, neccessarily, an Apple issue.

Have Sony reader 505, ADE doesn't recognize when attached to mac OX 10.6.8. works with reader library but not with ADE

Have Sony reader 505, ADE doesn't recognize when attached to mac OX 10.6.8. works with reader library but not with ADE

YEAY!
I just got the solution (that worked for me, anyway) from a Sony support rep. No PC or VMWare needed.
OK, you've installed Sony eBook Library v3, and Adobe Digital editions, you've set up your acocunts and authorized your computer on both of them, and you've authorized your Reader with the Sony Library application.
You go to the public library ebook download page, either through the Sony Library or just through a bookmark.
You check out a book, and open it in Adobe Digital Editions, which still won't recognize your Reader.
BUT, in the Sony Library app, you can now click "File, Import.." and go find the pdf you downloaded with the Adobe app.
On my Mac, it was in ~/Documents/Digital Editions
Import it, and drag it to your Reader.
The first time you do this, it will ask you to authorize the Reader with your Adobe ID.
Worked like a charm.

My Printer (samsung clx-3185fw) says it connects to my network but I can't seem to print wirelessly. I could with my netgear but not with my airport extreme, any ideas?

My Printer (samsung clx-3185fw) says it connects to my network but I can't seem to print wirelessly. I could with my netgear but not with my airport extreme, any ideas?
I have restarted all units, disconnected and reconnected

Hi ryanfromstockbridge,
I apologize, I'm a bit unclear on exactly what you are seeing when you try to add the printer or print to the printer. If you continue to have issues printing to this wireless printer, you may find the information and troubleshooting steps outlined in the following articles helpful:
OS X Yosemite: Printing troubleshooting
Troubleshooting printer issues in OS X - Apple Support
OS X Yosemite: Add or remove a printer
Sincerely,
- Brenden

Using iCloud my iCloud calendar is syncing with my iPhone but not with the Outlook calendar on my PC (Windows 7)

Using iCloud, my iCloud calenda is syncing with my iPhone but not with the Outlook calendar on my PC (Windows 7)

smurfanda wrote:
I agree. What I see is that it is creating an icloud calendar in Outlook but I want it to sync to Outook itself.
That is what it does. There is no sync, you have a new calendar.

Windows 8.1 64bit. Webcam works with "Camera" app but not with Skype.

I've spent a few hours googling and trying out various things - all listed below. I give up - any ideas??? OS: Windows 8.1 64bitMemory: 32GBWebCam: Microsoft VX-7000. As per subject - the webcam works with the "Camera" app but not with Skype for desktop or for Modern UI (or the Microsoft Lifecam software for that matter). Already attempted: 1) Uninstall webcam drivers - download latest from microsoft (Windows 7) and install in Windows 7 compatibility mode.2) Close (from taskmgr) anything that looks like it might use Webcam. 3) Run Skype for Desktop in Windows 7 and 8 compatibility modes None of the above work. In Skype for Modern UI the webcam doesn't appear in the drop down in Settings - so I can't even select it. In Skype for desktops (version 6.11.32.102) the webcam is found but instead of image I get "Can't start video. Try closing other programs that might be using your webcam". I see from a bit of googling that various people seem to have the same issue (i.e. Webcam works with Camera app but not Skype) - so I'm hopeful someone has found a workaround / fix to this issue and I've just not had the googling skills to find it Thanks, - Matt Symes

OK - I appear to have resolved the issue. I restricted my google terms to [vx-7000 site:microsoft.com "windows 8.1"] Which uncovered this article: http://support.microsoft.com/kb/933311 I noticed there were a couple of Windows 7 x64 specific registry settings that were mentioned so I checked these and they weren't as per the article. In fact - one of the Registry Keys was already used by other software "AI Charger+" which is some ValueAdd software that came with my motherboard. I uninstalled AI Charger+, uninstalled LifeCam driver. Reinstalled LifeCam driver in Windows 7 compatibility mode. Still not working. I returned to the registry and noticed the settings still differed from the above article. I corrected them (which involved not just amending Data but having to add new Values). I then disabled and reenabled the LifeCam from dvcmgmt.msc I was then able to get video from the webcam in the Skype for Desktop preview screen.

ESR,ID working with 8000 port but not with 50000

Hi experts,
I am working with PI 7.1. I am working with SOAP to ABAP SERVER Proxy scenario. I have downloaded the WSDL from ID and using XMLSPY sent a SOAP request to PI server and I got an error in SXMB_MONI under the Call Adapter step saying CLIENT_RECEIVE_FAILED.
We cross checked the services in SMICM transaction, and we missed the HTTP port 8000 for the parameter icm/servr/port_xx.
Then basis team changed the port 8000 in SMICM for the same parameter and restarted the Java stack.we checked the icm/HTTP/j2ee parameter which is having 50000 port.
Now ESR,ID,SLD,RWB... etc are working with ABAP port 8000 but not with 50000 java port and also I am getting an error in SXI_ CACHE while doing my delta refresh if_http_client receive http_communication_failure : http_communication_failure:ICM_HTTP_CONNECTION_FAILED. Kindly suggest me to resolve this error.
Naveen

Hi,
Re: Architecture of PI 7.1
NW PI 7.1 - ICM is not binding to port 5$$00
from the above two threads it is very clear that from PI 7.1 both the ABAP and J2EE ports are same.
Now we maintained both the ICM and j2ee port as 50000. Now ESR,ID,SLD are working with port 50000.
But in my SOAP to Proxy scenario I am getting the same error. When I try to send request to XI server using Altova xmlspy I am getting following error in SXMB_MONI under Call Adapter
<SAP:Code area="INTERNAL">CLIENT_RECEIVE_FAILED</SAP:Code>
<SAP:P1>400</SAP:P1>
<SAP:P2>ICM_HTTP_CONNECTION_FAILED</SAP:P2>
When i click that HTML error It shows
404 Resource not found
I am getting the following error in CC monitoring .
com.sap.engine.interfaces.messaging.api.exception.MessagingException: com.sap.engine.interfaces.messaging.api.exception.MessagingException: XIServer:CLIENT_RECEIVE_FAILED
My reciever communication channel is in green status CC monitoring.
I tested my server proxy in my end system which is successfully fetching data.
I am using the following URL format for generating the WSDL from Integration directory.
http://host:port /XISOAPAdapter/MessageServlet?channel=p:s:c
Do we need to maintain the Fully qualified host name in the above URL?
I tried with a test scenario which is an asynchronous communication with the above mentioned URL format. I got a success message in SXMB_MONI.
Since I am using PI 7.1 I tried the following URL also but i this case,the XML spy itself throws error. I couldnt see any messages in SXMB_MONI.
http://host:port/XISOAPAdapter/MessageServlet?senderParty=&sender
Service=FS&interface=IF&receiverParty=&receiverService=TS&interfa
ceNamespace=IFNamespace
I have seen many threads in SDN for this same error but I didn't get an answer for my scenario.
Lakshman and Manjusha
Thanks for the quick responses.
Regards
Naveen
Edited by: naveen perumal on Jul 24, 2009 8:00 PM

Wireless video link example works with antenna only but not with SMA to SMA cable

I am trying to run wireless video link example https://decibel.ni.com/content/docs/DOC-22728 . It works fine if I use install antennas on my Tx and Rx USRPs. But it does not work if I use SMA to SMA cable to connect Tx and Rx USRPs. Can somebody guide me what is the reason why it is only workng with antennas but not with SMA to SMA cable.
Thanks
JK

I connect the 30 dB attenuator at RF input port of Rx USRP. But it does not work completely.
Without connecting attenuator i was not able to receive any thing on my Rx VI although it shows waveform. But after connecting attenuator receiver some times receive text messages and some times not. Also it does not work at all for images and for video it works partially but gives some error related to memory full after few mins.
I want to know why this example works completely without any problem if I use antennas, and why it does not work perfectly if i use sma to sma cable for connecting transmit and receive usrps.
Please guide
Thanks
JK

Macbook Pro 7,1 (mid 2010?) boot with 6GB mem, but not with 8GB

Hello,
I bought a Macbook Pro 13" equipped with 4GB RAM at Apple Store on Oct-2010, and it says it's Macbook Pro 7,1 in profiler.
I tried to upgrade the RAM from 2GBx2 to 4GBx2, but the MBP freezed in boot sequence with 8GB RAM.
After some tests, including swap and change the combination of memory modules, I found my MBP can boot with 2+4GB configuration, but not with 4+4GB.
Does anyone know similar issue on the latest MBP 13"?

This is a memory speed problem - check here: http://discussions.apple.com/thread.jspa?messageID=13154160#13154160
When using 2+4 gb, memory speed is choosen, based on the slowest dimm - the 2gb one (1066mHz), when using single/double 4gb - speed is 1333mHz).
You can see the memory speed in diagnostic mode. I'm trying some stuff, if I succeed, I'll post my way.
ps. Changing 4gb memory sodimms to 1066mHz will solve your problem. Or if apple fixes the efi to downclock the 1333mhz ones (which btw every pc can do from the bios).

4g iPod works w/iTunes 5, but not with iTunes 2

I have two G4s, one with OSX.2.8 and iTunes 5, the other has OS9.0.4 and iTunes 2.0.4. My iPod will mount and work with the G4 with iTunes 5, but I haven't been able to get it to mount on the G4 with iTunes 2. I've used the same firewire cable for both machines, and the firewire ports seem to be working on the G4 w/iTunes 2. My iPod software is up to date. I tried resetting the firewire ports, but the iPod still doesn't show up. Is iTunes 2.0.4 too outdated to work with an updated 4G iPod? Any ideas?
Thanks,
Gary

I imagine that's the problem as well. What's the latest version of iTunes that is compatible with OS9? Is iTunes 2.0.4 it? My kids have a bunch of older games that they play on OS9 because the games freeze on OSX's classic environment, so I'm hesitant to move them over to X, but I bought my daughter an iPod mini for Christmas, and I want her to have her own iTunes library.

Why does my Web Handler work with Internet Explorer, but not with Firefox

I am trying to develop a web page that uses the Simile Timeline (http://code.google.com/p/simile-widgets/wiki/Timeline) with data from SQL Server.
In initial testing of my timeline I tested it with Example.xml, a static XML file in the correct format to be event data. I wrote the following in the appropriate place within mytimeline's Javascript: -
var WebHandler = "Example.xml"
tl.loadXML(WebHandler, function (xml, url) { eventSourceFamily.loadXML(xml, url) });
This worked fine with both Firefox and Internet Explorer. I then changed the assignment to
var WebHandler = "GDBTimeline.ashx?Type=Family&Userid=" + getControlValue("input", "hdnUser");
so that invoked a web handler that could look up the SQL database and return the XML that I wanted, and wrote this web handler.
This works perfectly with Internet Explorer, but with FireFox the timeline band is blank. Yet when I examine the http traffic with Fiddler2 (http://www.fiddler2.com/fiddler2/) I see that with either browser there is a response from URL
/GDB_pages/GDBTimeline.ashx?Type=Family&Userid=robertb
that returns the XML that it is supposed to.
I have previously used web handlers with Firefox before, with no problems. The Fiddler results conclusively show that the web handler is invoked, and returns the appropriate XML, and this XML is identical to the XML from the static test with Example.xml.
Where do I start looking for answers? I don't even know if this is a Simile problem, a Firefox problem, or an ASP.NET problem.
Thank you, Robert.

Problem solved. The issue: Content Type was not correct.
Visual Studio creates the web handler with dummy code like this: -
Public Sub ProcessRequest(ByVal context As HttpContext) Implements IHttpHandler.ProcessRequest
context.Response.ContentType = "text/plain"
context.Response.Write("Hello World")
End Sub
I wrote a database query that set a string variable to the XML I wanted: -
Public Sub ProcessRequest(ByVal context As HttpContext) Implements IHttpHandler.ProcessRequest
Dim Outstring as string
' my logic to fill Outstring with XML
context.Response.ContentType = "text/plain"
context.Response.Write(Outstring)
End Sub
This works with Internet Explorer. However it's not strictly correct: to make it work with other browsers as well,
context.Response.ContentType = "text/plain"
should be
context.Response.ContentType = "text/xml"
It now works with IE, FF, and Chrome, and presumably all others.

Front Row for Lion works with Movies, Photos, but not with Music!

Hi guys,
what do i do wrong? i installed front row and everything works fine, just no music. i always get the message...
FRONT ROW CANNOT FIND ANY SONGS!
so at first i thought there is something wrong with this app, but then i realized, movies and photos are working perfectly!
maybe someone has a simple solution for that problem?

Hi guys,
what do i do wrong? i installed front row and everything works fine, just no music. i always get the message...
FRONT ROW CANNOT FIND ANY SONGS!
so at first i thought there is something wrong with this app, but then i realized, movies and photos are working perfectly!
maybe someone has a simple solution for that problem?

Applet work with JRE 7_51 but NOT with JRE 7_45

Hello,
My major problem is, that my Applet signed with COMODO certificate DOES NOT WORK with JRE 7_45.
The SAME applet works fine with JRE 7_45, if I sign this applet WITH A SELFMADE UNTRUSTED certificate.
WHY the comodo signed applet doesn't run in JRE 7_45 ???
If i launch the comodo signed applet with JRE 7_51 it works perfect !!!
But in our company we got JRE 7_45 and I have to deal with JRE 7_45. That’s my problem.
Could you please tell me a solution what I have to do that the comodo signed applet works also in JRE 7_45.
Thank you!
Philipp

Thanks gimbal2.
I agree the problem may be in the proxy or in the firewall but I don' to know how to prove it as if i call the servlet url from browser I dont have problems .
The version im using is 6.45 but im sure the same problem occurs also with other versions of JRE6 .
... and the problem disappear with JRE7 ...
trouble is my company want people to use JRE6
any idea ?
Gio

PDF-Presentation works with Macs keynote but not with iPad keynote ???

Using this Converter PDF to Keynote" ( http://www.cs.hmc.edu/~oneill/freesoftware/pdftokeynote.html ) PDF-Presentations works totaly well inside Macs keynote. Transfering with iTunes to the iPad works well, too. But opening such a presentation in iPads keynote results in "Could not import, unknown error".
Are there any tips or tricks?
A.

Hi,
I didn't understand how you fixed the problem.
Could you please explain step by step how you sorted it?
Thanks

LDAP over SSL - Works with AD Username but not with full logon @

Similar Messages

Maybe you are looking for