LE8 not recognizing my Fantom x6 through usb

So, I have installed the necessary drivers and put my fantom x6 to midi mode, but when I plug in through usb, logic does not recognize it.
I want to be able to play logic's software instruments from my fantom (using it as a midi controller). I thought this was possible through usb. Is it the fantom?
I previously had a an m-audio keystation 49e that I plugged in and worked right away, but I'm very confused and frustrated with this fantom setup (or lack thereof).
Also, follow up question: Could someone explain what multi-channel instrument means? What qualifies as one, what would be a single channel instrument? I'm new to some of the lingo.

I couldn't find any info on the hub, but it's this one:
http://www.meritline.com/usb-2-0-f-w-combo-hub.html
Is there any easy way to plug my firewire external hd into my time capsule?

Similar Messages

"USB Device Not Recognized. One of the USB devices has malfunctioned..."

I'm running Windows XP with external hard drive. When hard drive is connected, iPod will not sync and I get message stating "USB Device Not Recognized. One of the USB devices has malfunctioned..."
When disconnect the external drive, he iPod appears in My Computer. However, iTunes is on external drive; therefore music is not syncing onto iPod. I've attempted the 5 R's as well as searching for iPod in Device Mananger. When iPod is conncected, it is listed in Devce Manage as "Unknown Device."
I've changed drive letters on boh iPod and external drive and get the same message. Please help.

QRe: Zen MX Causes "USB Hardware has Malfunctioned" Msg from Windows XpyUhh, Yes.
I used to same cable to attach my Motorola Razr and the computer correctly found it and identified it as such.
I also tried another cable (brand new) same thing.
I went to recovery mode and did a "CLEAN UP" but no dice.
I also got my I.S. tech guy to look into it and on the USB page it say "UNKNOWN DEVICE"? when he tried to delete it it did not help, it just reappears as "UDVC"? Also in looking into it it seems to have no drivers.
He came to this site and tried to do somethinm through here but it did'nt work.
Now in listening to it last night it began to 'skip' or what I call 'HICCUP" terribly. Where a song starts and stops, during the middle of it. ? It's always done it a little but it has been getting more and more common and now? It's WAY worse about it.
It has never been dropped, or nishandled in any way. I bought the clear hard case to protect it. And only has about 300 songs on it. Never used for anything else. No vids no pics, nothing.

Shuffle is not recognized thru 2013 Santa Fe usb port. Any suggestions?

Shuffle is not recognized thru 2013 Santa Fe usb port. Any suggestions?

You should consult the documentation or tech support for the car audio system, to see if a shuffle is supported as a device connected to the USB port. Also, there may be a setting on the car audio system, where you tell it that you are connecting an iPod to the USB port, and not something generic like a USB flash drive with song files.
When you connect an iPod to a USB port on a car audio system, it is just acting as a storage device. The car audio system is reading song files off the iPod and doing all the playing. Therefore, you may want to use a cheap USB flash drive with song files for this purpose, instead of an iPod. Here's one that barely sticks out of the USB port
http://eshop.macsales.com/item/SanDisk/SDCZ33008G/
and has four times more storage compared to a 2GB shuffle. You can also leave it connected to the car audio system, except when you want to update its songs, instead of having to constantly connect and remove an iPod. If you forget your iPod in your car, extreme heat or cold can cause damage.

IPod is not recognized by my computer's usb port and itunes

Remove my ipod from the computer without ejecting it and now the ipod want turn on, it is not being recognized by my computer's usb port or itune. I have reinstalled itune and still have the same problems.

1. Update iTunes to the latest version. Plug in your iPod. If iTunes still can't recognize it, then in iTunes in the top left corner click help> run diagnostics. On the box that comes up, check the last two things. Click next and it should identify your iPod.
2. Click on your windows start menu. Type in "services". Click on it and when it pops up, on the bottom of it click on "standard". Now Scroll down to find "Apple Mobile Device" Right click it when you see it and click on "Start". When it has started, close iTunes and replug in your iPod and it should show up.
3. Check the USB cable
4. Verify that Apple Mobile Device Support is installed
5. Restart the Apple Mobile Device Service and verify that the Apple Mobile Device USB Driver is installed.
6. If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job.
7. Check for third-party software conflicts.

IPhone 4 not recognized when connected to new USB 2.0 card

I have an iphone 4 OS4.1 on a no-name Windows XP Pro (service pack 3) PC with an AMD processor and lots of RAM.
I had the phone working and syncing beautifully with the onboard USB 1.1 but it was slow. So I bought a new PCI USB 2.0 card and installed it. Card is installed and there are no problems according to the status in System Devices.
But the computer does not recognize the iphone when plugged into one of those ports. If I plug it into one of the USB 1.1 ports that are still in the machine, it syncs and works fine. If I plug it into one of the new USB 2.0 ports, the PC shows the window at bottom right saying the device is not recognized. Tried the wizard but it's useless.
THOUGHTS?????

Nevermind!!!
It turned out to be a faulty cable! I tried it with a different sync cable and it works fine!
So disregard the question above.

TS1538 Iphone5 not recognized by Itunes, only shows USB and Itunes logo

I have tried all items listed my Apple. Will turn on and off but only shows itunes logo and usb. Not recognized by Itunes. Have been thru ALL items listed. Phone is less than a month old

Yes, we tried that, tried everything listed in the troubleshooting sections. Even checked pc with itunes. Took it to Applestore and they fixed it. I have no idea what they did but it's fixed and was free.

Hp officejet 4680 is not recognized by either wireless or usb connection. Windows 7 OS.

This printer used to work wirelessly to my Windows Vista Laptop, then I bought a new HP tower computer and now the printer is not recognized by anything, new or old. New computer is an HP Pavilion Elite HPE running Win 7, old computer is a Sony laptop running Vista. I've tried turning on and off everything several times, unistalling and reinstalling all softwware several times, and running the HP Home Network Diagnostic Utility (both basic and advanced tools) several times. I have a Netgear 2.4GHz wireless network router -- Security type WPA2, Encyption type AES and a functioning Netwrok securty key that is not recognized by the wireless network setting on by the wirelsss netwrok wizard on the printer tools application. I don't remember running the network wizard to enable the printer when I was only using the laptop.
Any help wopuld be most grateful.
Thanks.

I just fixed my J4680 printer a couple of minutes ago (see my post).
Step 1: Unplug your printer
Step 2: Uninstall the program J4680 and ALL associated HP programs (IRIS, Websmart, etc.). There is a screen to select ALL programs.
Step 3: Reboot your PC to complete the uninstallation
Step 4: Plug in your printer
Step 5: Download the FULL j4680 package from HP's support website:
Step 6: Run the Installation. The first screen will ask if you want a Wireless connection so click on that. It connected my printer automatically.
That's it. My printer is printing and scanning great.

External HDs not recognized by iMac when using USB cable

I just bought a new iMac & plugged in my two Western Digital 1tb drives using the supplied USB cables and neither of them are recognized by my iMac.
I've been using both of these drives with my other G5 iMac using the firewire cables & have not had any issues. I also purchased an adapter (USB -->firewire 800) and each hard drive mounts ... but neither will mount using the USB connections.
Any suggestions as to how I can get the second drive to work using the USB cable ...
Thanks,
Brent

+do I need to move the contents of the external drive off the unit before the partition?????+
YES! Absolutely! The partitioning process erases the drive, so you need to temporarily copy data onto your old Mac.
+how do I achieve this? I'm guessing there's a piece of hardware that I'll need to connect the two hard drives together and then feed another line into the iMac ... correct?+
All you need are firewire cables (hard drive to hard drive to iMac). See Dennis' link and the excerpt here:
+Question 7: Can FireWire devices be connected in a daisy chain?+
+Answer: Yes, and if the devices are designed according to the FireWire standard, they can be turned on and off as needed. For example, all devices don't need to be powered on to use the last device in the chain. For the best result, and to avoid overstressing the FireWire port, connect one FireWire device to the Macintosh, then add one device at a time to the chain. Avoid plugging in live power adapters into devices connected to the chain.+
And congratulations on your new iMac - you'll love it; I got mine about a month ago.

N95 USB id not recognized if behind two levels usb...

Hi,
I spent a lot of hour, to reconnect my N95 via USB, because, explanation at the end, it seems impossible to connect the phone is there is a HUB between the N95 and the computer (else than the native buitin-the-computer).
Before everything was installed since two years. By accident equipement bluetooth have been destroyed and Windowd XP SP3 installation should have to be redone.
Even I many people that I am a professionnal in informatics, expert in some subjects, I have been lost. I pass on erratics ways, and lost hours to go to the diagnostic : mine :
The USB driver is unable to recognize a N95 (always set to the right USB connection PC-Suite or OBVI) if it is connected on a second level USB Hub.
as I have only three USB main ports I use two USB (USB2 and USB ... ) on my portable (DELL Latitude D800 and XP SP3)
During installation of PC-Suite or OVI, the soft see the "new usb device", sometimes says 'N95 master...." but never reaches to end the installation : what happends :
- the windows USB detection sees too at the same time (behind the HUB) the new USB device and propose to install it automatically, while PC-suite says "installing" (what ?).
then :
If you don't make anything this can spend as long siecles you want.
If you say OK to windows : it answers "impossible to install" and later PC-suite say "you have problems with your connection". If you disconnect you N95 you can have the "blue screen on <ousbehci.sys at address F76BE41D based at F76B7000 datestamp 433c099a>
If on windows you answer "cancel" it immediately detects "a new device" and so on... eternally. But it will create for each try an undefined device into the device manager (stopped at 32).
Some times the main N95 is detected and some others are seen but never all the link devices are detected and soft installed you are reconducted to the previous situation.
This as been repeated on clean installations (unistalling part of drivers installed)
If you connect your N95 directly on the first level of HUB it is perfectly installed.
But as my Hub are well alimented and Ucc controlled (7 disks, camera, Micro-cards reader etc...) ir is not a current alimentation problem.
Later when you reconnect your N95 is not detected if it his not connected on the first HUB level (integrated to computer)
So after this bad experience I have one advice to the others users (by security) :
- never install threw a second level HUB
- if after a good installation at a reconnect via an HUB, the 'new USB device found' main USB installer panel appears (if you change of connection this can be normal) but fails, which is not normal, connect directly your phone only on a main USB connection of your computer (and clean your device manager - XP SP3)
Trebly
03/01/2011 16:15

im having the same problem i think. When I plug my bionic into my computer nothing happens on my computer or my phone. I can't access any files from my computer. I think I may be stuck in charge only mode but I don't know how to get out of it. I have tried this on multiple computers. Anyone know how to fix this?

Ipod touch 5th gen suddenly not compatible with volvo s60 through usb

My 5th gen ipod touch is suddenly not working in 2013 Volvo s60. When I plugged it in via usb this afternoon (as usual), message came up on screen saying ipod was not compatible with this accessory. I've already tried resetting it by pushing home and power button at same time but it didn't work this time. Worked fine until today. Any thoughts?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Try another cable if it is a Lightning to USB cable
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.

My iPod is not recognized by anything when connected USB. Firewire works.

Ok, so I haven't been able to put songs on my iPod for at least a month now... reason being, my computer doesn't recognize it. Hooking it to USB gives me this error message:
http://img79.imageshack.us/img79/1397/ipoderror28ea.jpg
However, it charges with Firewire (although obviously I can't put songs on it that way). What should I do?

I have exactly same error although my iPod version is 2.3. Initially got the error when I did not disconnect correctly (pulled USB out!!) I have successfully installed a new USB 2.0 & tried the reset options short of totally wiping my iPod clean but still get the Windows malfunction error. Once I get all my music backed up I will try the total wipe but if anyone has answer in meantime then all the better
Windows XP

After updating my 3gs to ios5 nothing works properly the phone is slow, no service, rapid battery drain, excessive heat when in use for longer periods of time, does not connect to vehicle stereo through usb, and screen is on but not responding to control

my 3gs battery dies rapidly and gives off excessive heat when in use no service anywhere, slow reponse time sometimes not at all like lights on but no one home, calls drop can text no 3g can not connect to vehicle usb as a note i restored the phone from my back up

Same problems, unfortunatley I updated to 5.0 1 hour before going on holiday for three weeks and no way to restore my phone to try to remove it.At the same time, drop outs, range problems and the most annoying was my music and apps were corrupted and would not function properly :-(

Windows 7.5 phone not recognized. Charges but no usb connection. USB works with HDD, Flash, 3G modem, Iphone, just no the Win 7.5 phone. Using 27" IMac with Lion.

When I connect windows Phone (HT7 using Windows Phone 7.5 (tried 2 phones) usb wont recognise it. Charges but no usb connection. USB works with HDD, Flash, 3G modem, Iphone, just no the Win 7.5 phone. Using 27" IMac with Lion.
I am running VMWare fusion when I connect any USB device Lion prompts to connect Windows or MAC. Both work for many devices. When I plug in the phone Lion simply does not respond.
Peter

Also.... my phone works and can do everything fine when not plugged in.. I just can't get my computer or others to recognize the darn thing when plugged in!

New 30g iPod Not Recognized By iTunes/Mac Using USB 2.0

Hey there folks . . . I just came home today with a shiny new 30GB iPod, but am having a little trouble in getting it to behave properly. The iPod doesn't show up in iTunes 7 or the Finder when I connect it to a USB 2.0 port. It recognizes the thing on a USB 1.1 port, but this is a very unpleasant way to fill a 30GB hard drive, so, hopefully there's some silly thing I'm overlooking . . .
The USB 2.0 controller is functioning fine and dandy it seems, my flash card reader, mouse, and keyboard all function without a hitch when attached to either of my 2 USB 2.0 ports. When the iPod is plugged in, it charges the battery, and it shows up in the System Profiler under the USB High-Speed Bus just as would be expected . . . but Finder doesn't mount it, and iTunes doesn't recognize its existence.
I'm running MacOS X 10.3.9 on an older G4 PowerMac, and I did upgrade to iTunes 7.
Any ideas? :-/

Try updating to the latest version of QuickTime http://www.apple.com/support/downloads/quicktime713.html Then reattach i-pod and let it update the videos & or podcasts..
This fix worked for me...
rnaphoto
G4 PB, G5 2.7 dual, G4 1.42 dual Mac OS X (10.4.4)

USB Device for IPOD not recognized by Windows, whether ipod connected or no

During the past few days I have received a pop up error message from (I would think) Windows that the USB device is not recognized. I have the USB plug for the ipod connected (as always)but the ipod isn't even connected. It keeps popping up like every few seconds that the usb device is not recognized.
When I attach the ipod itself, the ipod is recognizing it because it powers up. But, it took 10 times just to get the ipod to recognize through itunes. It updated, then immediately upon completion, windows again starting giving repeated error messages that the usb device wasn't recognized.
I have downloaded the newest itunes but I had it on my system for 4 days with no problems whatsoever. I don't think that's it. No other system changes.
I've deleted my temp files and cache. Also did a "disk clean up" and "defrag." It's still doing it.
Any suggestions?

I'm having the same problem. Ever since I upgraded to version 7, iTunes & my PC no longer recognise my iPod, and it therefore won't sync.
It's not the USB port (other devices work in it), I rebooted my iPod and re-installed iTunes, I've tried stopping and starting the iPod Service (but can't see my iPod in My Computer). When I run the Diagnostics it says iPod connection failed. I've even bought a new USB cable but that doesn't work either.
This is driving me up the wall. Is there a glitch with iTunes 7?
Can anyone help me out?? Thanks
Windows XP

LE8 not recognizing my Fantom x6 through usb

Similar Messages

Maybe you are looking for