Lenovo 3000 N200 ( Bios flash failed) now just black screen

Updating bios and froze ,had to take power out, now when turning on just a black screen no sounds, no bios, nothing ,i downloaded the update from the lenovo website and started the bios flash on about block 7 or 17 the laptop froze for a hour so i decided to pull the power out, on booting the laptop doesnt get past post, just a black screen ive tried phoenix bios recovery but i dont know if im doing it right ?

There's a lot threads about this kind of issue.
Please, use the search form.
Thanks.
Best regards.
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

Similar Messages

Pavilion g6t wont boot after bios update now just black screen please help!

I downloaded an update for the bios for my pavilion g6t-1d00 laptop running windows 7 64 bit. It started acting kind of funny but I didnt think anything of it til I tried to boot it up the next day and all I got was a black screen and a orange led light on the f12 button for the internet and the caps lock button after blinking afew times started the dredded two times every couple of seconds. I tried the windows key+B key power key, no luck. I cant access anything because I have no monitor and I'm at my wits end. I refuse to wipe my hard drive and start over even if I could! I cant access hp tools or manager or anything, please someone has to have a solution!

@Fuschia4me,
1.       You will have to use another computer
2.       Access the HP.com site with the BIOS updates available here is the link
3.       You want to select the F.36 BIOS version
4.       When you click on the update then click download and it will ask you to save or run, you want to save to a flash drive
5.       Once done insert the flash drive into your laptop
6.       Turn the computer on and press the windows and B key like before
If the process doesn’t work the first time I would try at least 2 more times.
Please respond back at your earliest convenience.
Thanks
Clicking the White Kudos star on the left is a way to say Thanks!
Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

Noisy fan on Lenovo 3000 N200

Hi,
I have had my Lenovo 3000 N200 for a week now. So far im happy with it. But ive noticed how the fan goes in intervals up and down very often. Have you noticed this also? Read about it in a review http://www.notebookreview.com/defaul...ew=Lenovo+N200 where it is described as the fan has "ADHD".
Sometimes (like now) Ive heard the fan go constantly (not max but still going so you can hear it) for about half an hour.
I guess its manufactured that way... or do you think its bad or wrong if it goes up and down like that? This is my first laptop so I dont have any experinces regarding this area.
Since this is my first laptop Ive no experience regarding how much the fan should go/sound. But is it normal that you can hear it while youre working at your computer?
The machine was pre-installed with Vista and i have tweaked it a little but still its not a very good OS for this machine I can tell.
I have plans on installing XP (saw on Lenovos homepage that its compitable with XP) and I have read about it on forums something about that you have to creat a install disc with SATA-drivers.
Thanks
Ekano

Hi
It is normal to hear the fan running, it shouldn't be loud but a wooshing sound is normal.
Window Vista does a lot of background stuff (far too much in my opinion) so your laptop runs hot. The fan will hardly be on with Windows XP (make sure you select the Portal/Laptop power scheme in XP to get even cooler running).
To slip stream the ACHI drivers for SATA you will need the F6 install files from Intel, the Intel Storage Matrix driver page has info about getting these files. To slip stream them into Windows XP Google for NLite.
The easiest way though is to go into the BIOS and set the hard-drive to Standard IDE, install Windows XP, then install the Intel Matrix drivers, reboot and set the BIOS back to ACHI. There isn't really much difference in performance between standard and ACH I modes.
Regards
Phil

Lenovo 3000 N200 0769 BIOS problem

Hello everybody! I'm a new entry in the forum, but i am a 6 year old user of a Lenovo 3000 N200 (0769) and i am very happy with its services so far! However, after a format that i make, i saw a BIOS update for this model, so i decide to install it. But the result wasn't the οne that i wish for. My poor laptop now when i try to open i can see just a black screen and nothing else. Although, i can hear the fan and the LEDs of the AC, HDD are light up (HDD's led is off after while). The laptop has got Windows XP 32bit.
I think i must recover the old BIOS, but i would like to see your suggestions and anwsers first.
Thank you.

Hi LongBeacher,
Welcome to Lenovo Community Forums!
I’m sorry to hear that your N200 is displaying black screen when tried to turn ON after updating the BIOS, Remove the battery and any other peripheral device connected to the computer. Hold the power button for 10-15 seconds and then connect only the AC Adapter and try to turn ON the computer, check if the display is working also check if the computer display is working in External display.
If the issue persists even after performing the above step, I would Strongly Suggest Calling Technical Support for Assistance. Click here to open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
Hope this helps!!!
Do post us back if the issue still persists.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Just bought a Lenovo 3000 N200 without a hard disk drive, need software

I just bought a Lenovo 3000 N200 Type 0769-BLG assembly date 07/09 from e-bay, it looks brand new but it had a fault, it was dead, perhaps a faulty motherboard and the hard disk drive had been removed. Assuming I can get the fault fixed, where can I get the Lenovo software that came with the original hard disk drive, I would prefer a free source, if that is possible, perhaps some kind person has put all of the CD's on to a DVD that I can borrow or buy a copy of. I was an IBM employee for 30 years before retiring 15 years ago. Dan McLean in Scotland, UK.

Call customer service directly to get a quick solution for this.
IPnaSh
First Spanish Community Guru - Colaborador ad honorem

Can't turn on my Lenovo 3000 N200

Hello, I've got a problem with my Lenovo 3000 N200 laptop.
Yesterday I used it without it's power supply, so it discharged. I let it charge, but none of the indicating power lights are lit up even though the power supply is good. It has now ''charged'' all night, but nothing has changed, no power lights and I can't turn it on. I'm confused, it's the first time when something like this happens, I haven't dropped it or anything it just completely discharged..
I already tried 2 times this trick when you remove the battery, push the power button for about 30 seconds and then put battery back in, but it didn't work.. :/
Any ideas or it's dead?

could be power cord or mainboard issue due to "no power lights"
i believe you don't have valid warranty but is it possible to contact local support center? you'll need probably some more help to diagnose the problem.

Lenovo 3000 N200 0769 ERG

I need urgent help please, I just bought a Lenovo 3000 N200 0769 ERG and we changed Microsoft Vista with
XP but we have a problem with the drivers. The Lenovo doesn't recognise them for example: Audio driver, Video VGA driver,
and all the drivers needed to run XP smoothly. Maybe we are installing the wrong drivers? Is there something that we
have to change in the BIOS in order to install the drivers ? If anyone knows where we can download the correct drivers
please tell me. Anything and everything will be appreciated.

im not sure if this will help new to forum but hey here u go anyways scan through the guide about the suipport & downloads should have all ur info there
http://forum.lenovo.com/lnv/board/message?board.id=N_Series_Lenovo_3000&message.id=2652

Lenovo 3000 N200 0769-ALU Dual Monitor Support

My nephew has a Lenovo 3000 N200 0769-ALU, downgraded from Vista to XP. Does this notebook support Dual Monitor Extended Desktop configuration? If so, how is this configured?
My nephew lives in a different city, so I am not able to just go over and lay w/ his machine. I am familiar w/ the dual monitor support on my HP LapTop, but am not sure what to look for on the Lenovo. Assistance is appreciated.
~ K

Computer is working now. The hibernation is still a problem.
I got a question though, i have SATA mode disabled now, but i'd like it to be enabled. How do i install this driver:
http://www-307.ibm.com/pc/support/site.wss/MIGR-67897.html

Lenovo 3000 N200 0769. Soon-to-be-doorstop unless...

Hello.
New forum member. I joined because I have been passed a Lenovo 3000 N200 0769 by one of my good customers (I look after all their IT). My notes indicate that this was purchased January 2008.
The problem does not seem unique. It will not start at all. Pressing the power button and releasing it results in the power ‘z’ light to illuminate for a few seconds. That is all. No hint of the screen illuminating, no fan noise, no other action at all. No accessories attached.
No BIOS updates have been applied (he would not know how). The user is not a fiddler. This PC is a tool for his job and the company relies on my business to look after these (computer) tools, rather than have their executives fiddle about.
I have tried it with battery only, with battery and mains unit, with mains unit only. Nothing.
I have searched this forum and spent too long reading threads. The only conclusion I have is that this is not an unusual problem and that (Murphy’s Law) it happens shortly after a twelve month warranty period expires. The nearest suggestion is motherboard failure. Forlornly I tried to check the warranty, to see if it was longer than 12 months. On the Lenovo warranty lookup page it returned an error with ‘document not found’ message – hmm…
Happily the data is backed up, which means the user does what he's asked! Hopefully the HDD is OK, which gives me a tiny fragment of value.
Does anyone have any ideas how to rectify this problem? Thus far my experience of Lenovo has not impressed. This could be my last experience of Lenovo. If there is no meaningful response I just don’t know what my thoughts will be.
Please will someone help me?
Thank you

Hello.
Thanks for the fast reply and the suggestion.
When I press the orange button it has the same result as when pressing power button: brief illumination of green 'z' light and nothing.
I had already seen the suggestion about resetting CMOS and tried that, although it said it was the CLRP1 spot, opposite the modem. Is there another spot by the RAM? I can't see anything.
I've also removed the RAM and HDD - still no luck.
Any other suggestions will be very welcome.
Thank you again.

Problem with Lenovo 3000 N200 0769 Laptop

Hi all,
I'm new here and hope someone can tell me whats wrong with my Lenovo 3000 N200 0769. Two days ago I got up in the morning and turned on my laptop, it started and shut off about 3 seconds later. It does it every time I try to start. I was able to get the windows intro, and then could not sign in as the keyboard didn't work. When I unplugged the power cord it immediately shut off. Is it a Battery malfunction thats caused this or a Virus? PLEASE I need some help here!! I googled it and on some other sites some said it was the Battery. Thanks very much.
Regards,
Michael

Also, with the battery out and AC unplugged, press and hold the power button several times. Then, re-attach AC and try to start it up. You could go into BIOS and reload BIOS defaults (that's an option) save and exit. Try to start up normally again.
If the system boots up only part way, hangs, or shuts off then I would tend to think the fan & heatsink could be clogged. See this article on cleaning.
http://forums.lenovo.com/t5/Lenovo-3000-and-Value-line/Lenovo-3000-Fan-amp-Heat-cleaning-N100-exampl...
The N200 is very similar to the N100 in this regard.
If the fan and heatsink are clean, I would check the battery - these systems don't like to run with just the AC. Try to see if it will start up from just battery with no AC, or start with battery in and AC, and then unplug AC. If it shuts off, then the battery is defective and should be replaced. Most of these, especially N100 seem to do much better with a good battery.
Best regards,
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Lenovo 3000 N200 0769 ERG upgrade memory 1GB- 3GB only recognize 2GB

I bought a Lenovo 3000 N200 0769 ERG with 1GB installed in first slot.
To get the system better work I wanted to expand the RAM.
As the spec's tell a maximum of 3GB should be possible.
Thefore I added a 2GB mem-card.
I expected to see the I would have in total 3GB in use.
Now the system and BIOS tells that only 2GB is in use.
I already checked:
- startup with only 1GB works correct.
- by adding the 2GB card the total value increased from 1 to 2 GB so the card is expected to be correct
+ systems works correct
- only using the 2GB card gives problems, system doesnot recognize RAM at all.
On this forum I see some suggestions to place 2 x 2GB cards and Vista only recognizes 3GB.
Is someone aware that this may be a solution?
Does someone else have an other solution.
Your help is very welcom.
Thanks in advance.

Wow, thank you, what an awesome little tool!
So, I found that these 2 RAM products are compatible with my laptop:
Part Number: CT758799
Module Size: 2GB
Package: 200-pin SODIMM
Feature: DDR2 PC2-6400
Specs: DDR2 PC2-6400 • CL=6 • Unbuffered • NON-ECC • DDR2-800 • 1.8V • 256Meg x 64 •
Part Number: CT699699
Module Size: 2GB
Package: 200-pin SODIMM
Feature: DDR2 PC2-5300
Specs: DDR2 PC2-5300 • CL=5 • Unbuffered • NON-ECC • DDR2-667 • 1.8V • 256Meg x 64 •
I then went to a well-known auction site and found RAM cards from the same manufacturer with exactly the same specs as above but with different Part numbers. Does it have to be the exact part number or do I stand a good chance of it working if it has the required spec? I searched for the exact part numbers and yielded 0 results.
Thanks for all your help on this.

How to enable execute-disable bit and other hidden settings on Lenovo 3000 N200 model 0769!

2008-11-16: I have posted some more settings, scroll down to message 19 in this thread to read them.
Hi,
Here's some good news for anyone with a Lenovo 3000 N200 model 0769, who is disappointed and frustrated with the lack of options in the BIOS setup menu. (I had a moan about that in this thread.)
This is a long post but I hope you'll find it worthwhile. Here are the features/settings which I will explain how to enable:
The BIOS disables the execute-disable bit function of the CPU, with no way to turn it on. You can enable it.
You can set VGA and VESA graphics modes to not be stretched to fill the whole screen (sharper graphics with no distorted aspect ratio).
Speed up the POST display by skipping the memory test
Disable various features (if you don't use them, that might save some power): the HD audio controller, WLAN card, on-board LAN, shadowing of the video BIOS
Enable beep before booting the OS
Enable key click sound (only in DOS, not Windows or Linux)
I'm still working on this, and hope to figure out more hidden settings soon, e.g. to disable the DVD drive and trackpad, and to change the video output from NTSC to PAL.
The information below applies to the Lenovo 3000 N200 model 0769 with BIOS version 3.03. My N200 has Nvidia graphics. For some background on the general principles/research required to figure this out, please see this thread at Wimsbios.com.
To change the settings, you need to create a bootable DOS floppy disk or USB drive. Download SYMCMOS.EXE (Google for it) and put it on the bootable disk. Boot the disk and run SYMCMOS to back up your current CMOS settings: SYMCMOS -Lsettings.txt
Next load the settings.txt into a text editor. It will begin like this:
( SYMBOLIC CMOS EDITOR - Version 643710-035 )
CRC = 3EDD
(0000) [0001]
(0003) [0001]
Your CRC value may differ. Each line after the CRC contains a token number, followed by the value of that token. You can start with the settings.txt you created and edit any tokens you want to change, or delete all token lines and just include the tokens you want to change. Then use SYMCMOS.EXE to apply the new file: SYMCMOS -V2 -Uupdate.txt
After running that command you can reset, and hopefully notice the new settings in action. (For certain settings, such as re-enabling the execute-disable bit, you need to turn the computer off then on again.)
Here are some specific tokens you can change:
Token Default New Description
(0000) [0001] [0000] Disable the HD audio controller
(0042) [0001] [0000] Disable LCD panel graphics scaling/stretching
(004B) [0000] [0001] Beep before booting the OS
(0267) [0001] [0000] Enable support for the CPU execute-disable bit
(028E) [0000] [0001] Enable key click (only works in DOS and BIOS setup)
(02A3) [0001] Set to 0 for slower memory test, or 2 (or 3?) to skip
test for faster booting, especially with 4GB RAM
(046E) [0001] [0000] Disable video BIOS shadowing. (Best to leave enabled.)
(0471) [0000] [0001] Enable 1MB memory hole at 15MB. (Best leave disabled.)
(0486) [0001] [0000] Disable PCI Express ports 1-6. This takes precedence
over the individual port bits below, and disables the
LAN, WLAN and (probably) ExpressCard port.
(0489) [0001] [0000] Disable PCI Express port 2 (WLAN card)
(048C) [0001] [0000] Disable PCI Express port 3 (maybe ExpressCard?)
(048F) [0001] [0000] Disable PCI Express port 4 (LAN)
For example, if you want to disable LCD panel scaling and enable the execute-disable bit, you would create a text file like this:
CRC = 3EDD
(0042) [0000]
(0267) [0001]
Some final points:
Loading the default settings in the BIOS setup menu will overwrite any changes you make using SYMCMOS.EXE. So keep that bootable disk around in case you need to re-apply your settings in future.
The token numbers above are specific to version 3.03 of the Lenovo 3000 N200 model 0769 BIOS. They might be different for earlier BIOS versions, and will be different for other models of computer.
Once you have created a bootable floppy disk with a text file containing your updated settings, you could create a bootable CD with the floppy's data on. Just boot that CD to restore your settings in future.
Before experimenting with randomly changing token values to discover other hidden settings, make sure you know how to reset your computer's CMOS memory! Changing some settings results in your computer becoming unable to boot, so you can't use the BIOS setup screen to reset. I wrote about how to reset the N200 model 0769 CMOS in this thread.
If you discover any other settings, please let me know.
Any changes made are at your own risk; if you "brick" your laptop don't blame me!
Message Edited by Donuts on 10-15-2008 09:45 AM
Message Edited by Donuts on 11-16-2008 11:35 PM

Hi Donuts !
My computer is a 3000 N200 0769BAG. It has a Dual Core Pentium and the information I get about the BIOS using lshw are :
========================================================================================
description: BIOS
          vendor: LENOVO
          physical id: 0
          version: 68ET35WW (04/16/2008)
          size: 106KiB
          capacity: 960KiB
          capabilities: pci pnp apm upgrade shadowing escd cdboot bootselect edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot biosbootspecification
====================================================================================
I've nothing telling me it is a 3.03 BIOS version but only got the BIOS file name (68ET35WW);
Is it the same BIOS you used and if not how could I find the list of (token, default value,new seting) for that particular BIOS ?
Thanks a lot in advance for your help !
Regards

How can I install Microsoft bluetooth stack on Lenovo 3000 N200?

Hi there,
so far I have failed to get the Microsoft bluetooth driver working on my Lenovo 3000 N200 with Windows XP in order to easily sync my BlackBerry via bluetooth. The RIM software requires the Microsoft driver and does not work with the Lenovo driver.
I have managed to deinstall the Lenovo driver. However, I do not know how to install the Microsoft driver.
Could someone please help me?
Have a nice weekend, everyone!

When I used BT for the first time (pre XP SP2 era) I just installed the MS BT package that you can download. Later SP2 came out and it was included as part of it. You just plug a BT stick in and its installed...
One out of two: or your XP is old or the bluetooth brand is non-standard... In the past many BT, network, etc. hardware came with its of drivers and application, maybe you can find out your exact model and search for the application by any manufacturer that uses the same chip.... Should be Lenovo of course, but....

Lenovo 3000 N200 0769 Startup Problem

Hello,
I recently installed a new harddrive which is a Samsung HM251JJ 250GB 7200rpm
Before I inserted the new harddrive I disconnected the the power supply and akku as mentioned.
I started the Laptop and after the message mouse initialized the System hangs... So I have no chance to get the Boot Menu to install the Operating System...
First I thought, might be a problem with the harddisk itself but I've run a full harddrive scan with serveral tools also from Samsung itself but all reported that the haddrive should work fine...
Next thing I did was a Bios update to the newest available version, which does not solved the problem.
Another Idea I got was installing another harddrive this time also a Samsung with 250GB but instead of 7200rpm it had 5400rpm that drive worked fine...
So I wonder if the Lenovo 3000 N200 does not support harddrives with a speed of 7200rpm???
best regards

I once had a "wake" key stuck on a keyboard, and the computer kept re-booting!
I thought maybe the "one touch restore" button, or one of the F key could
be stuck partially down.
Your computer problem is very strange, have not heard of that one before.
Sorry to be no help.

Lenovo 3000 N200 (0769) | Windows 7 | What driver do I need?

Hello,
fist of all I'd like to mention that I am german and consequently am not familiar with all the technical terms in their english incarnation. I am going to describe what I mean the best way I can.
Here's what happened: I fell victim to a virus the other day, which forced me to format my harddrive an reinstall Windows 7 Ultimate on my laptop, a Lenovo 3000 N200 (0769). All went smoothly exept for one thing: I can only choose between a solution of 800x600 and 1024x768. This is apperently due to my computer not beeing able to detect my graphics-device-card-thingy. I know it is in there however, because before i reinstalled Windows everthing was fine.
Assumably there is a driver missing. I tried to find out which one I it was by installing Everest and have it have a look at it, but a message popped up that Everest does not suport my particular laptop. And indeed there was no information it could give me concerning my graphic devices.
I wound greatly appreciate any help I could get.
Thanks,
Giles

please provide the device name or/and id. ( such as pci\ven_8086&dev_2929&subsys )
( just click the unknown devices from the device id tab )

Lenovo 3000 N200 ( Bios flash failed) now just black screen

Similar Messages

Maybe you are looking for