Lenovo 3000H series Desktop Motherboard

Dear Members.Could anyone of the forum member help me to get a good working condition Lenovo 3000H series Desktop Motherboard?Please offer your price.Thanks!

Think there is really nothing you could do. Mine is also faulty. I changed the internal battery of the m/board and the bios set up continuously asked me to press F1 to enter setup or F2 to resume. Worst, it getting from bad to worst, the power supply seems to be giving trouble too. I am a seasoned guy who used to build desktop from scrap and i have one that is based on 486 which is still working today. Inspite of its fame(ie IBM) lenovo's m/board doesn't seem to be so lasting afterall.

Similar Messages

  • Lenovo H Series desktops H520 Desktop bios

    Hi
    desktops H520
    My problem I entered the bios and changed a bit in the settings specifically in devices Video Setup I do not remember what this has done is important to change a setting from Automatic to the middle option I do not remember what it was and then became the screen does not signal
    How do I treat the problem
    thanxx
    Solved!
    Go to Solution.

    Copy this link and paste it on your browser and you'll see an interactive bios. The same as your computer. In the video settings, if you click on the AUTO it will open more options. Hope this helps you.
    http://service.lenovo.partner-management.com/content/CoursewarePublic/15412/H520BiosSimulator.swf
    CB2011

  • Lenovo X201 Series Tablet/Laptop

    Hi I recently bought a Lenovo X201 Series Laptop but the screen is cracked it has a touchscreen interface I would like to know can I replace the touchscreen with a 12.1inch LED or LCD Screen as I dont want to spend to much on a touch screen details of laptop is below
    Product ID: 2985DMG
    Specs:
    Corei7 CPU,500GB Hard Drive 4GB Ram 12.1inch Touch screen.

    Hi,
    there is a lot matrices are installed into x201t. Models also depend of the backlight type - LED or CCFL. I'm not sure whether any supported matrices models are compatible with your laptop. Also there are different LCD cable assembly and LCD rear cover assembly depending of the backlight type.
    To ensure what matrice you have and what's compatible check out on Lenovo' site parts list of your laptop by its [laptop] serial number. Support site doesn't answer a question by MTM only.
    I think it's impossible to fit non touch matrice into the tablet because of the different size (width). Compare the width of x201 and x201t.
    UPD
    Service parts DB says your laptop has 12.1-in. WXGA LCD panel, LED backlight (300-nit LCD), FRU 45N6092 or 45N5388.
    x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
    x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
    Do it well, worse becomes itself
    Русскоязычное Сообщество   English Community   Deutsche Community   Comunidad en Español

  • Cannot use recovery cd`s of lenovo T60 series thinkpad

    hi i am manu and i am using a lenovo T60 series thinkpad laptop.
    lastday operating system crashed and up on one of my friends i installed a windows xp evaluation version (only after installation i came to know it was evaluation and needs activation).
    after all these only i checked my recovery cds and its manual. by that time every thing in the hard disk has been formatted.now when i insert recovery cd 1 and it continues till 2% and then hangs down. after some time message shows that files have been recovered and remove disks and restart. but when restarted this is what is shown please help me....
    [IMG]http://i243.photobucket.com/albums/ff191/grimmygrave/DSC07132.jpg[/IMG]
    http://i243.photobucket.com/albums/ff191/grimmygrave/DSC07132.jpg
    [IMG]http://i243.photobucket.com/albums/ff191/grimmygrave/DSC07133.jpg[/IMG]
    http://i243.photobucket.com/albums/ff191/grimmygrave/DSC07133.jpg
    please help me any one...........

    manu, welcome to the forum,
    your recovery cds, are these cds which you created yourself, or are they from Lenovo?
    Please also state how many discs you have and what they are named.
    This information will enable members to offer you hopefully the right solution.
    Thanks
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • Predictions: When will Lenovo X-series support 802.11ac ?

    When do you predict we will see a Lenovo X-series laptop introduced that supports 802.11ac ?
    FYI - 2 sites I read for reliable tech info, including home networking:
    http://www.anandtech.com/show/7127/the-joys-of-80211ac-wifi
    http://www.smallnetbuilder.com/wireless/wireless-reviews
    I'm getting 375-405 mbps by hanging this orb
    ASUS Dual-Band Wireless-N900 USB Network Adapter
    http://amzn.to/14ql6WG
    off my downstairs Thinkpad's USB port .
    That orb pairs with an ASUS RT-N66U Dual-Band Wireless-N900 upstairs.
    On the downside, it's something permanently plugged into my USB port. 
    On the upside, with a USB cord extender, it easily stays put on the laptop coffee table.  And I like the idea of the antenna being further away from my brain.  Most importantly, the performance is compelling. (it seems to be twice as fast as before)

    Any Lenovo laptop with mini PCI-E port should support 802.11ac as long as there's no whitelist in the BIOS. I could've put the Intel Dual Band Wireless-AC 7260 on my Y470, but instead I chose the Intel Dual Band Wireless-N 7260 since the Wireless-AC version has a bluetooth integrated which conflicts with my Broadcom bluetooth that came with the laptop. The Wireless-AC itself works, but both my Broadcom bluetooth and Intel's bluetooth won't work (they both show an yellow triangle with exclamation point on Device manager). The Wireless-N version has no bluetooth so the built-in Broadcom bluetooth works fully.
    Lenovo Y470: i7-2670QM | 8 GB DDR3 1333 MHz RAM | Nvidia GeForce GT 550M | 500 GB 7200 RPM Seagate HDD | ASUS PCE-AC56 802.11ac Network Adapter | Windows 7 Professional 64-bit

  • Bluetooth Freezing up on Lenovo T Series Computers

    Lenovo T Series Community
    I own three Lenovo Laptops (T400-Win 7 x86, T430-WIn 7 x64 and T520-Win7 x64) and I have problems with the Bluetooth locking or Freezing up. Its more prevalent on my T430 system than the other two although it happens with them occasionally too.  Typical I have issue when booting up my T430.  The booth tooth never seems to load.  I simply select the Fn +F5 key and re-boot the Bluetooth and I'm off.  With the T520 and T400 the problem usual occurs while using the computer.  Happen 2 - 3 times a week. Again, all I have to do is select the Fn+F5 key and re-boot the Bluetooth radio and typically have no further issues.  Any suggestions about what maybe going on.
    Jeff

    Lenovo T Series Community
    I own three Lenovo Laptops (T400-Win 7 x86, T430-WIn 7 x64 and T520-Win7 x64) and I have problems with the Bluetooth locking or Freezing up. Its more prevalent on my T430 system than the other two although it happens with them occasionally too.  Typical I have issue when booting up my T430.  The booth tooth never seems to load.  I simply select the Fn +F5 key and re-boot the Bluetooth and I'm off.  With the T520 and T400 the problem usual occurs while using the computer.  Happen 2 - 3 times a week. Again, all I have to do is select the Fn+F5 key and re-boot the Bluetooth radio and typically have no further issues.  Any suggestions about what maybe going on.
    Jeff

  • LENOVO C SERIES ALL IN ONE DESKTOP PC

    Hi...Im new to this site and just wanted to ask a question,
    I bought a lenovo all in one c series pc..Only a few days ago,
    I got it home and booted it up as you do,
    Then it went to mircosoft updates and found 45 updates....So it downlosaded them and it went to reboot but all i got was a blank black screen with just the wireless light and the power light on...
    Any ideas to what is happening ?....
    Im from the UK if that helps
    Rob

    I have had the exact same problem and it is confirmed it is down to the Intel GMA 3150 update that Windows Update installs for you.
    I recommend you print or write the following instructions down before doing them as restarts are required throughout the process.
    If the Intel GMA 3150 update has been installed you'll find your computer will go blank once it's loaded into Windows. There is an update available from Lenovo that I'll explain about below, but first you need to uninstall that update that is causing the problem. Press the power button on your Lenovo All-in-One for it to automatically switch off. Then turn your computer on again. AS SOON AS YOU SEE THE LENOVO START UP SCREEN, continue to press the F8 key until you see many options listed on a black background with white text (basically keep pressing the F8 key for 5-10 seconds when you see the Lenovo bootup logo). The reason for this is because the F8 key is registered just after the Lenovo bootup logo. If you don't see anything on your screen within 10 seconds, your display may be turned off even though the power is on - press the button next to the power button on your display to turn it on, and you should see the options I described.
    Now use your Arrow Key on your keyboard to select Safe Mode (choose the first option) and it'll eventually boot into Windows. Then go to the Start menu, right-click on Computer and select Properties. Then from the new window that'll appear, select Device Manager from the left hand side. Then in the newer, smaller window, double-click under "Display" and find the Intel Graphics Media Accelerator option - right-click on it and select "Uninstall". Make sure from the next window that pops up you select the checkbox to delete the files relating to the driver. It will probably ask you to restart your computer at this point. Your computer should boot up into Windows as usual but everything will appear bigger than usual.
    When you're logged into Windows, go to the Start menu, search for Windows Update and launch the program. From the left of the new window, select "Change settings" and where it says "Important updates" there's a drop down box; choose "Download updates but let me choose whether to install them". This is a temporary measure to ensure the Intel GMA 3150 driver isn't reinstalled until we install the update from Lenovo that fixes this issue.
    Now, this blank screen issue has been rectified by Lenovo in the form of a software update that is available from http://consumersupport.lenovo.com. From there enter your serial number (found on the back of your computer) - or alternatively select the option that starts at the top of the list of Lenovo computers - for instance, my All in One is Lenovo C200 so it's listed as "3000 C200". From there, find the BIOS update that can be installed via the operating system which is at the top of the list of the drivers available. Download the .exe file, run the application for it to install itself and then restart your computer once it is installed. Then go back to the downloads page at http://consumersupport.lenovo.com and also download the second file which has a .txt extension (I believe); these are the instructions. Follow the simple instructions. Once you have followed the instructions you'll see it asking you to enter any key to restart. For me it didn't restart the computer so I had to do this manually by pressing the Windows key on the keyboard which opens the Start menu and using the arrow keys to get to the Restart section of the Start menu. Once your computer restarts, go back to Windows Update and change settings back to "Install updates automatically". Now click OK and then back at the left section select "Check for updates". Once it has checked for updates click on the "important updates available" link in the Windows Update window and find the Intel Graphics Media Accelerator option (if you can't find it, from the left select "Optional", it should be in there instead. Whichever one it is in, make sure all updates are DESELECTED in both Important and Optional and then go back to whichever section the Intel Graphics Media Accelerator Update is in, and select that update, then click OK from the bottom right and go ahead and install it. Once it is installed, you'll find your display goes black. Don't worry at this point, this is the update installed. Wait 1 minute and then press the power button for 3 seconds for your computer to turn off (once you press the power button it'll take a few seconds to turn off). Turn on your computer again and you'll find it boots back into Windows fine with that Intel update that previously caused a blank screen at start up. Everything is now done and the Intel update is now installed. The reason it causes a black screen after it is installed I don't know, but after turning off/on again, everything works fine - since the BIOS update has fixed the blank screen at start up problem.
    Hope this helps. I know it's in depth, but it shouldn't take too long. I'm a customer and not a staff member at Lenovo, by the way and I did everything I described above when I had the same problem. A Lenovo staff member over the phone did explain about the Intel GMA driver causing problems when I called for an unrelated problem and then it happened to me later on, realising it's the Intel GMA driver that Windows Update installed.
    My personal tech blog

  • Froze at "Press any key to restart" on Lenovo 3000 J117 7387 series desktop with XP

    My system froze up the other day and I had to do a hard reset, and now the above is displayed at startup, and I haven't been able to figure out the cause or solution.  Any ideas?  Am I going to need to order a recovery CD from Lenovo and lose all my data?  I did not create a recovery disk (dumb me).  I have tried the F8 restor method and can't even get that to come up.....
    Help!
    Message Edited by G8rgrad98 on 02-24-2009 11:46 AM

    I had the same problem that was driving me nuts.
    Solution here:
    http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-67513
    Lenovo should have this driver for download on their drivers page for the J115, but they instead erroneously state that Windows XP has a native driver.

  • Lenovo Z Series Z50-75

    Bought the Laptop today. And registered it. But could not register the date I got the computer. It only shows the date it was manufactured. And for me that means om loosing nearly alot of time of my warranty. Also not possible to update Windows 8.1 from Windows update. Nothing wrong with my internet. Since it works with all my other appliances. Not sure what to do with this. Since I have to wait all to Monday to bee able to call support. I also found out that its not possible to even email support in Norway, for some reason.
    Solved!
    Go to Solution.

    Welcome to the Lenovo Community !
    Sounds like you purchase your laptop from a retailer other than Lenovo.  In those types of sales the warranty date starts on the day the retailer purchased their shipment from Lenovo.  Generally Lenovo will add an additional month to the warranty to make up for the time the computer may have sat in a warehouse or on the store's shelf unsold.  With your purchase it sounds like it sat longer than expected.  Not a problem.  Use my link below to update your warranty purchase date.  Choose the Americas as the Region and submit.  On the next page will be a web form.  Choose Inform Machine Purchase Date and fill in the form.  You can then attach a scan of your receipt and submit it to Lenovo.  Your warranty period will then be updated with the new date.
    http://shop.lenovo.com/gb/en/services-warranty/ser​vices_registration.html
    Owner & Operator of the following:
    ● Lenovo Ideapad Z570 w/ Win 7 & Win 8.1 Dual Boot ● Lenovo Yoga 3 Pro w/ Windows 8.1 ● Toshiba A75-S206 w/ Win 7
    ● IBM Thinkpad T-23 w/ Win XP ● IBM Thinkpad T-22 w/ Win XP • As well as multiple desktops dual/triple booting XP, Vista and Win 7.
    ★ Find a post helpful? Thank that member by clicking on the ☆Star☆ to the left awarding them a Kudo.
    ★ Posting a problem and a reply is helpful and it answers your question, please mark it as an "Accepted Solution"
    ★ I'm not a Lenovo employee, just a volunteer geek who likes to help folks. Enjoy your time here, pay it forward by helping others !
    ★ Sorry, I don't answer questions via Private Messages. Posting in the appropriate forum is the best way to get assistance.

  • HP PRO 3400 Series desktop won't boot CPU fan starts and stops , no video, no beeps

    I have the above computer with an i3-2125 CPU, Windows 7 Home Premium 64 bit, and a 300GB Seagate Hard drive.  I've had it for about 2 years and been working fine. It started acting up about 2 months ago.  It would lose the date and time.  I checked the battery, and it was OK, so I kept using the computer.  Then on 9/15/2014 it hung on "Starting Windows", I did the following:
    1.  Ran the built in HP diagnostic on hard drive and memory and they both passed.
    2.  Tried to go to last known good configuration and nothing happened.
    3.  Noticed the date and time were off, replaced the battery, nothing changed.
    4.  Tried another hard drive from another HP PRO 3400 Series and it would boot up but could not set date in bios.
    5.  Tried all kinds of things but could not set date in bios.
          a.  Bios date read 48/00/0048 after removing and replacing battery.
          b,  Tried to reset date to 9/16/2914 and it gets 56/00/0051
    6.  Then it wouldn't boot at all.   So now when you turn on the power, the CPU fan starts and runs for about 1 second, then shuts off for 4 seconds, then starts and runs for another 1 sec and it does this continuously.  There is  no video and no beeps and no difference when all memory is removed.
    7.  I removed the power supply, and checked voltages.  It appears to be OK.
    8.  I removed the motherboard, and inspected it- saw nothing obvious.
    9.  I connected the power supply to the motherboard with nothing else connected to the motherboard, and I get the same thing.  CPU fan starts then stops continuously, no video no beeps.
    10.  I am thinking it is the Motherboard, but I sure could use some suggestions as to what to do next.
    Thanks
    Maxgle from CA

    Maxgle, welcome to the forum.
    I believe that you would get more responses to your problem if you start a thread here.  They are the members who know your computer best.
    Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • Result code: WHD01V012-DK7B1F - lenovo g50 series

    Kindly be informed that i have run the lenovo diagostics for storage devices and got the below result. MY system has been dead slow these days and most of the time the screen will be in hung state.. So let me know whether my harddisk is crashed DiagnosticsSMART Status TestPassedTargeted Read TestFailedRandom Seek TestPassedFunnel Seek TestPassedSMART Short Self TestFailedSMART Drive Self TestFailed

    Good day.
    You can contact Support directly at:
    United Arab Emirates
    IDEA-branded and B, C, E, G, H, K, N, Q, V, Y Series Products
    Arabic
    8000-3570-2810 (Standard charges apply)
    9:00 - 18:00 Sunday - Thursday
    Regards.

  • Battery Maximizer Lenovo 3000 Series

    I would like why no Battery Maximizer software for 3000 Series systems/notebooks?
    Why only for ThinkPad series?

    I tried but it says "cannot install on this system"
    whats more interesting? the lenovo training website says you need to use the battery maximizer software to get maximum battery time.
    So I ask where is battery maximizer software for N100 3000?

  • Ayuda Lenovo C2 Series

    necesito ayuda mi ordenador lenovo c2 no me lee la tarjeta sd, me pone :  Intel(R)Pentium(R) processor N- and J-series/Intel(R) Celeron(R) processor N- AND J series EHCI USB - 0F34.

    Hola kevin9gomez6 que tal,
    Sigue este enlace http://forums.lenovo.com/t5/3000-Series-C-H-J-K-Q-S-D-E/lenovo-solution-center/m-p/1799939/highlight... , para ingresar a BIOS F1 cuando tu ordenador este apagado.
    Un saludo.
    @Antony_Vamu
    Comunidad en Español  English Community  Deutsche Community  РусскоязычноеСообщество
    Mis Lenovo: Y560p,Z580,Z500 touch,S920,T400,G50-70 ,Soy voluntario no trabajo para Lenovo, las opiniones expresadas por mi no representan a Lenovo, no se responde a preguntas de manera privada debes crear un nuevo tema, números del centro de llamada Lenovo Aquí , reglas de participación del foro Aquí , si encontraste solución a tu problema marcarlo aceptándolo como solucionado!!!!!

  • LENOVO H3000 Series 88242AA

    Hi! I'm new here.
    May i know what RAM can this computer support? & what graphics card can this computer support?
    Thanks in advance.
    Message Edited by HKS on 02-26-2008 01:28 PM

    Hi yuyu,
    Welcome to Lenovo Community Forums!
    First Try this,
        Turn OFF the Computer
        Remove the AC adapter
        Remove the Battery
        Hold Down the Power Button for 15 sec.
        Reconnect Just the AC adapter (No Battery) and try turning it on.
    IF The steps above does not work.
    Try Contacting The support in you current location and See if you can have the system serviced.
    Nigeria
    IDEA-branded and B, C, E, G, H, K, N, Q, V, Y Series Products
    English
    234-1277-0800
    8:00 - 17:00 Monday - Friday
    Hope this helps
    Cheers!

  • Lenovo S10 Series Black Netbook

    My question is when you order the S10 in black does that mean the keyboard is black.  My Son's friend stated that it's black on the outside but the keyboard is white.
    Also I wanted to thank Mark the Admin here for resolving the battery replacement question on my other Son's Y510.  I apologize for a well over due thank you and we are all one big happy Lenovo family.  Thanks again Mark for the extra effort!
    Best regards,
    wslandry6

    He might be thinking of the pre-release version that appeared on the web.  The current versiobn is ll black, including the keyboard.
    http://www.lenovo.com/shop/americas/content/img_lib/products/splitter/notebooks/IdeaPad/S-Series/gal...
    Message Edited by nonny on 11-16-2008 12:09 AM

Maybe you are looking for

  • How to add a button in Sales Order screen?

    Hi, Basically I want to add a new button "Show My lookup" in sales order screen and when clicking the button I want to show a form. Please anyone tell me how to do this?. thanks in advance Mina

  • Convert to a date format

    Hi, I have a table with a date field that comes as varchar2(20byte) with a content like this: 20/Jan/2011 and I need it to be converted toa real date format e.g. 20.01.2011. Please help, Thanks Walter

  • I need to reinstall PSE9 in a new MAC. For my surprise, this MAC doesn't have CD drive. So, I need t

    I need to reinstall PSE9 in a new MAC. For my surprise, this MAC doesn't have CD drive. So, I need the link to download the PSE9 for MAC.

  • Burn / Formatting Finished

    There seem to be a few unanswered treads on this topic so I hope someone has the answer. I'm using an older version of DVDSP. It was working fine so had no reason to upgrade but slowly I'm losing functionality. My problem now is when I try to burn I

  • Note to all upgrading to ML

    I just did the DL and install Of ML on my 15" Late 2011 MBP and first I saved a complete copy of the downloaded files. I then searched for the InstallESD.DMG file so I can in the future make my own ML Install USB thumb drive. I created a separate par