Lenovo Beacon file transfer too slow

dear all, i'm a newby here and i need your help. I own a Beacon with 2x1TB HDD in RAID 0 mode, so when i move datas to Beacon the max. file trasfer speed is up to 5 mb/s. In my opinion this is tooooo slow. Can anyone help me, or say about your file tranfer speed to Beacon. My configuration: Lenovo Beacon + Netgear 5-port Gigabit Switch (GS305) + Win7 PC. Everything is LAN wired. I already tryed another PC (Notebook) but with the same result. Thank you!

Beacon use HTTP protocal, and we use Filezilla as benchmark comparison (Note, Filezilla use FTP protocal.)
Test config: Router, Netgear WGR614 V9 with Lan speed 100Mbps, Thinkpad Notebook (win7) wire connected to router, Beacon wire connected to router .
Test Result: Single file speed 5MBPS, and three files 10MBPS by Beacon; single file 11.6MBPS, multiple files 11MBPS

Similar Messages

Switch log file is too slow

hello,
my database is 10R2
the specified size of online redolog file is 50mb
the switching of log file is too slow..
even though the size of archived log file has become around 50,029,there is still no log switch of file..
why the log switch is not occuring immediately after the size reaches upto that limit(50,029)...?
what might be the setting do i need to do..
any help ....any guess ??
thank you..

Hello,
The frequency of the log switch depends on the activity of the Database.
You may check the Alert log for some messages like this:
Thread 1 cannot allocate new log, sequence ...
Checkpoint not completeWhile Oracle needs informations in the Redo log to complete the Checkpoint, it cannot reuse it. So, it can happen that the Database doesn't switch the redo log up to the Checkpoint is complete.
If you have this kind of messages, the following link may help you:
http://asktom.oracle.com/pls/asktom/f?p=100:11:0::::P11_QUESTION_ID:69012348056
Often, it's solved by adding redo log files.
The Parameter fast_start_mttr_target may also help the Database to optimize the checkpoint:
http://download.oracle.com/docs/cd/B19306_01/server.102/b14237/initparams068.htm
Else, if you don't have this message ( checkpoint not complete ...), but you want to log switch more frequently (even if the Redo log is not completely full), you have the parameter archive_lag_target. It can help to force log switch every n+ seconds:
http://download.oracle.com/docs/cd/B19306_01/server.102/b14237/initparams009.htm
NB: It's not recommended to get log switch too frequently, in general you shouldn't have more than 3 or 4 log switchs every hour.
Hope this help.
Best regards,
Jean-Valentin
Edited by: Lubiez Jean-Valentin on Mar 5, 2011 11:44 AM

Local file transfer speed slow on E1200

On a local file transfer (computer to NAS or NAS to computer) my file transfer speed with the E1200 is way too slow. I would expect the Wireless N speed to be at least 54mbps (megabits per second), which would be equivalent to 9 MegaBytes per second.
In practice the speed of transfer appears to be at 8mbps (1 MegaByte per second). Here is a screen shot:
The speed is the same whether I copy from the computer (on a wireless N link) to the NAS, or from the NAS (on a 100Mbit ethernet port on the E1200) to the computer. The NAS is brand new, auto configured to a RAID-1 setup with two new drives.
Anyone know why this is? is the encryption (WPA2-PSK/AES) slowing down the transfer? The same problem occurred with copying a folder of photos as with copying this large file. I don't think I can upgrade the firmware on my device, as I have the first version of the E1200.
Solved!
Go to Solution.

Sabretooth --
There is no option to set the Qos to zero. I can set it to "auto" in which case the number has no effect.
I could set it to manual but it restricts me to a range as you can see from the graphic.
In case you are wondering, my internet speed is 10Mbps downstream, 5Mbps upstream. So I am getting the same speed for the internet that I am getting for a local transfer.
The next troubleshooting step is to bypass the wireless and hook my PC to the router. I will let you know if that makes a difference.

Tiger Updates Have Broken Airport Appleshare File Transfer, Horribly Slow

Big horrible slowdowns in file transfer over wireless have me pulling my (remaining) hair out. I have seen several other posts and here are results of what I found. Hope you can add some suggestions.
I had given my Apple Airport base station (b) to my brother in Pakistan after I found a Belkin (g) at Staples for free (after rebates) and have been using it for a while (maybe almost 2 years). Not a pretty box but the price is beautiful and it works OK.
My real use for it is for my eMac and a couple of older PowerBooks I keep downstaors as a "music studio" for my music and podcast recording (and transferring upstairs to my server folder over wireless) and web browsing.
All worked OK as I would transfer the files to my PowerBook upstairs (connected Ethernet to a router connected to the wireless router or sometimes directly via Airport connection if laptop was not at my desk). Both configurations worked fine (only limitation being my eMac's (b) speed older Airport speed).
Since 10.4.4 or 10.4.5 (as that is the last "change" I can see made on my system overall, I have discpovered I cannot even transfer a 3.5 MB file from the 10.4.5 eMac to ANY of the other machines.
After reading several threads here it seems several people have noticed the HORRIBLE SLOWDOWN if not complete death of Airport usability for file transfer. People are being made to go around changing router settings, channel IDs etc. That sounds like typical tech support bunk to me.
After all, if the channel ID on the wireless router is a problem why is my web browing going on at normal speed but a 120 MB file transfer just told me it will take 2023642128 hours. No, I am not kidding. That is the time it would take to get man to Mars.
Someone else was told to hook up the machines over Ethernet. Sure, that works for machines in the same room - and is a bearable temporary solution in that case - but not in an upstairs/downstairs situation. Burning CD-Rs to transfer 120 MB files every time is also not a good way to show off Apple technology.
So, in my humble opinion, some recent update from Apple just broke something in Airport networking or Appleshare. So, I did some more testing.
I love Apple, getting friends to switch all the time, but annoyed at these bugs that basically render standard applications unusable. So far I have not been able to figure out what the problem is. Here is some more info I got.
I already deleted all the network port configurations on the 10.4.5 eMac except wireless. Activity Monitor shows 0.1 to 11 kbps speed (yes, that is 0.1 to 11 Kbps not Mbps). No other apps are running, Tried connecting to different machines. All machines can transfer data at high speed except over Airport/wireless.
I then fired up a PowerBook G3 500 10.3.9. It is slow as a machine, but it has no problems picking and dropping files on to other machines over Airport (it is sitting in the same area as the emac so signal etc. issues would effect them equally).
Next I came upstairs and changed my 10.4.5 PowerBook G4, previously working perfectly on Ethernet,to Airport only use. Lo and behold, it could not go to the Internet nor could it do any AppleShare transfers even with a PowerMac G4 which is Ethernet only.
There could still be two culprits, the Apple 10.4.5 update OR maybe the wireless router went bad. So I tried all of the above after changing channels on the Belkin router. Still no luck.
It could still be the router, so:
- I changed the HP 17" 8080 laptop from Ethernet to wireless only and it flies.
- I switched the PowerBook G4 BACK to Ethernet and it flies.
- I kept the PC laptop on WIRELESS and did file transfers from it to the now ETHERNET using PowerBook G4 and it works fine even PowerBook to PC and PowerBook to PowerMac both using Ethernet and 10.4.5 works fine too.
- I now tried to get or put files from the 10.4.5 ETHERNET PowerBook G4 to PowerBook G3 10.3.9 WIRELESS and it worked fine. i.e. no problems with older OS one using wireless.
- Then I tried 10.4.5 PowerBook G4 Ethernet to eMac wireless 10.4.5 and it would not take or drop a file, unless I was willing to wait for 3 years and 2 months.
In other words - the ONLY common thread is that 10.4.5 with wireless/Airport use will break Appleshare file transfers.
Obviously some planetary confluence did not suddenly corrupt all the settings in all my computers at the same as many others, who also happen to be using 10.4.5 or maybe 10.4.4 because the 10.3.9 using OLD PowerBook with 512 MB RAM does wireless file transfers faster than the 10 times faster Macs using Apple's own cards and newest software.
Seems like a now-becoming-usual Apple update that breaks things.
Hope you can suggest a solution so I do not have to burn CDs on the eMac for every 1 MB file I need to transfer upstairs.
Imran

Oosted on macfixit.com Friday, February 24 2006 @ 09:30 AM PST
Mac OS X 10.4.5 (#9): Another fix for network slowness -- re-applying the combo updater; SIIG FireWire card not working; more
Another fix for network slowness -- re-applying the combo updater Over the past few days we've outlined a number of fixes for network slowness that occurs after the update to Mac OS X 10.4.5, including entry of a DNS address, toggling of IPv6 and more.
We've now received notes indicating that a tried and true workaround for various issues -- re-applying the Mac OS X 10.4.5 combo updater (as noted in our general workarounds for 10.4.5) -- can have beneficial effects in this case as well.
MacFixIt reader Fred Moore writes:
"After much thrashing about and wasted time, I appear to have solved both the slow web page loading as well as my email sending problems in one stroke. Guess how: download the Mac OS X 10.4.5 combo updater and reapply it. This nonsense has cost me a lot of time but everything seems to work now. IPv6 is set back to Automatic, there is no entry in the Network prefs DNS server field, and my email sending works perfectly (so far; I've sent a bunch of tests). Why didn't I just download the combo updater and apply from my hard drive at the beginning? Well, Software Update should (yes, I know, I know...) work. I'll never again use Software Update for a system update."

Why is my file transfer so slow?

I got a Time Capsule for Christmas and am hoping to use it as a backup drive but also storage facility.
I understand it can take some time to back up the initial disk (I've only had my Macbook since October) but 72GBs taking 24 hours and stalling at 5 seconds remaining is unusual isn't it?
I also tried copying a folder the size of 8GB to the drive and it said it would take 2 hours to do this! Is there a common problem with the transfer rate?
And are there any fixes?
Colm

You are using wireless I presume. Wireless is a shared media and transfer speed on wireless whilst absolutely fine for internet is going to slow things right down to move large files. The basic recommendation is to do the first backup over ethernet and then use wireless for the incremental backup.. anytime you need to move large files or directories then cable it.
8GB in 2 hours is slow.. but the estimation is made at the point the wireless maybe busy. And those estimations are not accurate at all.
Try and get the your Macbook close to the TC and check the link speed. You can see it by holding the options key and clicking the airport icon... at least you can in SL .. Lion not sure.
You want it using 5ghz as the TC is slow in 2.4ghz and range is poor at 5ghz.
IMHO it is better to force the wireless yourself to 5ghz by using different network names. But Apple designed it to automagically swap to the fastest link.. the trouble is, links tend not to be dropped during a file transfer.
stalling at 5 seconds remaining is unusual isn't it?
Not for wireless it isn't.

File.length() too slow?

I'm working on an application that needs to process directory listings on network fileserver, looking for files and directories, and getting basic info about files found (size, last modified date).
I'm trying to use java.io.File.list(java.io.FileFilter) with java.io.FileFilter returning file.isDirectory() or file.isFile() to get a list of just files or directories, and try to get the rest of file information later for each of the returned Files. However, when it gets to a directory with a lot of files (13000+), it seem to be unacceptably slow. I have tracked it down to File.length(), taking up to 80ms per file (!), which amounts to only about 13 files per second.
It's not a problem of the platform (Win XP), directory listing contianing all information I need takes less than 3 seconds for this big directory, while getting the same through Java APIs (calling isDirectory(), isFile(), length() and lastModified() within the FileFilter callback ) takes ages.
Is there a better way to get a directory listing, without being orders of magnitude slower than necessary? I can think of calling native dir command and parsing the output, but that is a mess...

I have tracked this down to native implementation of File.length() - VC++ runtime function _stati64 which they use to get file length is too slow.
Why dont they use Windows API? I have tested that getting file size using GetFileAttributesEx() is at least 50x faster than _stati64 for my file!

File sharing too slow

Hi,
I have 2 macs connected via hub. My internet connection is very fast and everything is ok but file sharing is too slow. 1GB takes 8 hours to be transfered.
Any fix?
Thanks!

yup same here, 9 gb file shared via airport extreme from my Macpro 8proc to my 17" Macbook Pro was going to take 4 hrs?????? doing it via firewire now, 10 minutes.
is there a network setting in missing as both machines obviously have 902.11N and the extreme is setup for N (B/G compatible)??
jas

Windows 7 network file transfer absurdly slow

I know there are plenty of other posts about slow network file transfer. Here, elsewhere, I can't say I read them all but most are referring to slow down to 1MB/s.
I am getting <20KB/s.
If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for
a long time and then begin with <20KB/s immediately.
This is a fairly newly built desktop. Realtek gigabit on-board LAN of ASRock Extreme3 gen3. I have tested network file transfer to and from a Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens
with one direction, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue.
Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s.
I looked everywhere and can't find symptoms that fits my case well. I'd be cheering if I can get 1MB/s. Well, maybe not, but at this point it is more efficient for me to upload everything to the Internet and download them again than to use local file transfer,
which is just absurd.
I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look.
Any suggestions are greatly appreciated, thank you in advance.

Hi,
Firstly, would you please try again to install the HotFix instead of disabling TCPAuto-Tuning and Windows Scaling heuristics via netsh manually.
If issue persists, please try following:
1. Test the issue in Safe Mode with Networking.
2. Disable "Large Send Offload".
How to:
1) Open an elevated command prompt and press Enter:
netsh int ip set global taskoffload=disabled.
2) Disable and re-enable the network interface or reboot your system.
3) Run the following command in an elevated command prompt to confirm the command above is successful:
netsh int ip show offload
3. Check the value of “Speed & Duplex” is Auto in Advanced Properties of the NIC. If not, please let us know your value.
4. Check if “Flow Control” is disabled in Advanced Properties of your NIC.
5. Go to your Start Menu, search for “Local Security Policy“ and run it as administrator. Under Security Settings -> Local Policies -> Security Options.
1) Open “Network security:Minimum session security for NTLM SSP (including RPC based) Clients”,
unselect “Require NTLMv2 session security” and “Require 128-bit encryption”.
2) Do the same operation to “Network security:Minimum session security for NTLM SSP (including RPC based) Servers”.
3) Open
the policy “Network Security LAN Manager authentication level“. Locate and select the option “Send LM & NTLM – use NTLMv2 session security if negotiated“. Click Apply, and close out of all
policy management windows.
Hope this helps.
If a post solved your problem, click “Mark as Answer” on the post. If a post helped you, click "Vote As Helpful" on the left side of post.

Time machine file transfer very slow during OSX 10.7 re-install

I am using a macbook pro, and was running 10.7. (not sure exact version, and cannot look now, but should have been up to date) I tried the free upgrade to Mavericks, but it failed and said I had a disk error. At this point I could not boot back to 10.7 so I booted with apple-R. I tried to do a repair from disk utility but that failed so I erased my hard drive. Then I proceeded with an install of 10.7, which proceeded fine. I got to a point where it asked about transferring files, (forget the exact wording) and I said to use my time machine backup (from right before I tried the upgrade - backup was 80GB) and I started that. It has been 16 hours and it still has not finished. The external hard drive (Lacie) clicks / whirs, and I see signs of very slow progress... (seems to be at about 80% now judging by the progress bar) but it can go hours without any noticeable change. The "time remaining" information is variable -- going up and down -- and is clearly not correct-- has said 1.5 to 2.5 hours for the last 12 hours
Any ideas? should I just wait a few more days   should I abort and restart the file transfer (if so, what is the best way to do this?)
I cannot provide details on the computer since it is still busily restoring (I hope), but it is roughly 3-4 years old, lots of free space on hard drive (>100GB),

These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter the word "Starting" (without the quotes.) You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard."
Each message in the log begins with the date and time when it was entered. Note the timestamp of the last "Starting" message that corresponds to the beginning of an an abnormal backup. Now
CLEAR THE WORD "Starting" FROM THE TEXT FIELD
so that all messages are showing, and scroll back in the log to the time you noted. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
☞ If all you see are messages that contain the word "Starting," you didn't clear the text field.
☞ The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. Don't post more than is requested.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.

FILE TRANSFER RATE SLOW FROM WIN SERVER 2012.

Dear Team
The File Transfer problem From my Windows Server 2012R2 (File server) showing 200KB transer rate in 1g network. Please help

Hi,
What's the operation system are you using, Windows XP/2003 or Windows 7/8/2008/2012?
You can test to disable SMB2/3 and see if issue is related:
Set-SmbServerConfiguration -EnableSMB2Protocol $false
See:
http://support.microsoft.com/kb/2696547/en-us
Note: This is just for testing and you can enable it after testing.
If it is SMB related, try to disable the TCP Chimney Offload, Receive Side Scaling and Network Direct Memory Access features.
Information about the TCP Chimney Offload, Receive Side Scaling, and Network Direct Memory Access features in Windows Server 2008
http://support.microsoft.com/kb/951037
Here are the steps to disable RSS, TCP Chimney Offload and NetDMA:
netsh int tcp set global rss=disabled
netsh int tcp set global chimney=disabled
In HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters, double-click the EnableTCPA registry entry.
Note: If this registry entry does not exist, right-click Parameters, point to New, click DWORD Value, type EnableTCPA, and then press ENTER.
To disable NetDMA, type 0 in the Value data box, and then click OK.
Let us know if issue still exists.
Meanwhile we have an Forum FAQ article which provided some suggestions and quick-fixes for network slowness issue. Please see if it could help:
[Forum FAQ] Troubleshooting Network File Copy Slowness
http://social.technet.microsoft.com/Forums/windowsserver/en-US/7bd9978c-69b4-42bf-90cd-fc7541ccb663/forum-faq-troubleshooting-network-file-copy-slowness?forum=winserverPN
If you have any feedback on our support, please send to [email protected]

How do i fix a file where relinking or updating file is too slow and generating 60+MB pdf from a 4mb Indesign file?

I have an 18 page files linking several pdf images and working with this file is horribly slow. These pdf images(total of 15) easily take a min to relink or update (pdf's are at max 2mb but majority are less than 1mb). The Indesign file is only 4mb but when i export or print to pdf I get a 60-70mb file. Exporting or printing these 18 pages easily takes 30 min. I can't use the file with a higher display quality unless i have the patience of watching a plant grow on that day. I've read a majority of ways why InDesign would be slow. At work im operating Windows 7, Indesign 6 and I have 32MB of RAM. Extremely frustrating and reminding me of the days of dial up internet. I've already done a SAVE AS and tried to reduce linked files image size and to no avail has not helped. I was able to get my 72mb pdf file to reduce to 6mb after using Adobe Acrobat and getting rid of the hidden information but I lose alot of quality in the linework. I am guessing its because these pdfs are generated from Revit or Autocad is why it might be holding onto some hidden info. So how do i make this file work faster (relink,export,pdf etc)?

Just to note as well, InDesign only links to files, there's no embedding, you would see a 4mb file, but if it's linked to a 10mb pdf and it has to include all that PDF in the final file then it will be circa 14mb file.
What you have is a vector heavy PDF and there's no real way to reduce that without losing quality.
You may have better joy by opening the linked PDFS in acrobat and using File>Print and choose Adobe PDF (or another method) to basically refry the CAD pdfs.
I'd do this with a copy of all the files though just in case something goes drastically wrong.
Frankly, I feel it's the nature of how CAD pdfs are made that's causing the downfall here, refrying these and Printing these files to PDF removes a lot of the complicated things happening in CAD files and makes a very dulled down PDF version.
Once you've done this then try FIle>Export from indesign to make your pdf.

HT4527 Th the music file transfer so slow

How can this be done faster?

Get a faster network (not Internet) connection.
Get faster computers.
Transfering files via the network has nothing to do with iTunes. The speed of the network, amount of memory on the computer, and the speed of the processor dictate the speed at which files transfer.

File transfer EXTREMELY slow over wireless connection

Hi there,
I have recently been transfering some files from my TiVo to my iMac via a wireless connection. I don't know if the files are going through my router first, and then coming to my iMac or what, but the transfer rate is really slow; about 50 - 100 KBps. That's Bytes, not bits. I know that 802.11g is 54 mbps, which translates to about 7 MBps, but I'm getting about 1/70th that speed.
I recently moved my computer to a part of my house that has better wireless reception. I have an AirPort extreme card that is 802.11g compatible, an 802.11g Linksys wireless router, and a D-Link 802.11g wireless USB adapter hooked up to my TiVo. 2 dashboard widgets that I have tell me that the connection strength to my iMac is excellent (>75%), and that the speed is full (54 mbps). My iMac discovered the TiVo with the "Bonjour" technology built into Mac OS X. It doesn't make any sense to me. Even if the files are going through the router, everything is operating at 7 MBps, so why am i getting 50-100 MBps? Any help is appreciated!
Thanks,
Trevor

Here's what I did:
I moved my computer to a place where I could connect to my wireless router through an ethernet cable. I tried to transfer files from the TiVo again using the same application, and the download speed was no faster. I tried having both Airport and Ethernet on, and it was slower. I tried just Airport, and it was no faster than before. So I found a new way to download the shows using Safari and Bonjour. I tried, and it was downloading at (according to the downloads window)... 0B/s. I thought "Great". I can't even download it at all this way. So in desparation, I moved my computer right next to the USB device that the signal is coming from, and I get the same download speeds using the application. I try with Safari, and this time it actually starts downloading faster than 0B/s. The top speed I've seen it at is what it's hovering at right now: 129 KB/s. Now here comes the interesting part:
My internet connection (loading webpages with Safari) was lightning quick everywhere my computer was. That indicates that the issue is with the USB device on the TiVo, and not my router or mac. I looked for an ethernet pot in the back of my TiVo, but I could not find one. I found a phone jack (for connecting to the TiVo service via the phone), and my iMac has a phone jack too, but then I realized that the application I was using and Safari needed to use either the Ethernet port, or AirPort, so that wouldn't have worked. I guess that the TiVo cannot process and export the info at faster than 100-150 KBps. Oh well.
Trevor

File transfer very slow with a SSTP VPN

I have a serer in the office and I connect from my house through a SSTP VPN. In my home computer (client) I add a new network folder, this networkf folder is in the server, that has a shared folder. I can transfer files, but is very slow.
For example, to transfer a folder that contain about 20 files, and in total are 11MB, it takes about 3 minutes. The server has a upload bandwidth of 890kbps. With teamviewer VPN takes about 1minute with 55 seconds.
The problema with the SSTP is that the transfer speed is not stable, bteween 0-200kbps. The problema is that when has to transfer a file, always the same, the speed drop to 0bytes/s and in this state is about 1-15 seconds and continue the transfer. Why?
So the total time at the end it's much more than the time that I need if the connection was stable and used all the bandwith. How I say, teamviewer VPN takes about 1:55 inteado of the 3:00 of SSTP.
Thank so much.

Hi ComptonAlvaro,
Please check if we have other program is connecting the Internet when we use the SSTP.
Additionally, we could contact the ISP to check the stability of network.
Regarding the slow SSTP performance issue, we could refer to the following thread similar to this issue.
http://social.technet.microsoft.com/Forums/en-US/8e8e4220-af25-4627-bed2-47db8c04d318/sstp-and-slow-transfer?forum=winserverNIS
Please take the following steps to fix this issue:
1. Add new registry key and value “ TcpAckFrequency=1 ” for all NICs on VPN server, so that we can reduce ACK delay.
2. Disable Windows 2008 SNP feature, and restart VPN server
3. Disable TCP Checksum offloading on VPN server
Hope it will be helpful.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Airport Extreme file transfer speed slower than expected.

I have an Airport Extreme with a 1 TB drive attached.
I'm trying to copy a bunch of files to it with a Windows Vista computer with a D-Link wireless N dual-band adapter (connected to the 5GHZ channel, which I configured to act solely as wireless N 5 GHZ), but the transfer is only taking place at 1.3 MB/sec.
I'd expect more in the 8-9 MB/sec range for my new router given other benchmarks I've seen. What could be going on?

I have an Airport Extreme with a 1 TB drive attached.
I'm trying to copy a bunch of files to it with a Windows Vista computer with a D-Link wireless N dual-band adapter (connected to the 5GHZ channel, which I configured to act solely as wireless N 5 GHZ), but the transfer is only taking place at 1.3 MB/sec.
I'd expect more in the 8-9 MB/sec range for my new router given other benchmarks I've seen. What could be going on?

Lenovo Beacon file transfer too slow

Similar Messages

Maybe you are looking for