Lenovo care don´t work after upgrade to windows 7

...and I can´t find any upegrade for Lenovo care on this site. Have Lenovo dropped all upgradeservice to this computer.
I have un Lenovo 3000 N200
tommy berkert

I had these problems with a T500 and Windows 7 Pro 64-Bit.
For anyone that is experiencing problems with Windows 7 64-Bit, try this procedure:
1. Uninstall the Authentec True Suite software.
2. Uninstall the Lenovo Fingerprint Software.
3. Reboot.
4. Reinstall the Lenovo Fingerprint Software. 3.3.0.56
5. Reboot.
It worked for me, I had every error imaginable and most of the ones you all have mentioned, including "please insert the primary sensor" and "Cannot communicate with sensor. Please confirm sensor is ready" errors. True Suite is a product put out by Authentec that acts like the Lenovo Fingerprint software. It has a fingerprint manager that looks a lot like the Lenovo one. I believe that it loads second and takes control of the reader, so the Lenovo software believes the hardware doesn't exist.
Note: Also, in Device Manager, under the fingerprint reader device properties, I told windows that it wasn't allowed to make the reader sleep to save power.

Similar Messages

G460 WiFi + Bluetooth don't work after upgrading to Windows 7 Pro x64

I recently did a clean installation of 7 Professional 64-bit. I erased OKR partition and everything else. The install went fine, but the OS doesn't recognize the Broadcom card or the Bluetooth unit. I've tried installing each of the drivers available on the Support and Downloads page, but nothing there has worked. I even tried manually installing the drivers through Windows' Device Manager, but nothing.
The BIOS was updated. I've tried "restoring defaults" on BIOS. Nothing. The third light (for WiFi/BT) comes on when the computer starts but turns off once Windows is loaded. Also, the Fn+F5 combo doesn't work although the other hotkeys work. I even tried removing the Broadcom chip from the computer, booting Windows, shutting down, and then re-installing the hardware and re-booting Windows, but nothing.
This is terribly frustrating! Any help would be appreciated.

re-install power management for hotkeys.
use vista drivers instead of windows 7.
if the drivers on support page doesn't work, try to install drivers from here

Bookmarks don't work after upgrading to Firefox 5.0

My bookmarks don't work after upgrading to Firefox 5.o. Please help! The icons no longer show and instead there is a blank paper with the top right corner folded. I can't even bookmark new pages! I tried reinstalling the program and that didn't work. Please help!

Your bookmarks file may be corrupt. Navigate to /[UserName]/AppData/Local/Mozilla/Firefox/Profiles/[profile_name]. Either rename places.sqlite to places.sqlite.corrupt (or whatever) in case this isn't the problem, or delete places.sqlite. Start/Restart Firefox. The icons for sites that have a favicon should return after you visit each site.

Genius gamepad don't work after upgrade to Yosemite.

My game Genius Maxfire 3 gamepad don't work after upgrade to Yosemite, please help.
Juan.

Try deleting the previews directory and then rebuilding the standard previews.

Bookmarks and reading lists don't work after upgrading to ios6 on ipad

Bookmarks and reading lists don't work after upgrading to ios6 on ipad

Your bookmarks file may be corrupt. Navigate to /[UserName]/AppData/Local/Mozilla/Firefox/Profiles/[profile_name]. Either rename places.sqlite to places.sqlite.corrupt (or whatever) in case this isn't the problem, or delete places.sqlite. Start/Restart Firefox. The icons for sites that have a favicon should return after you visit each site.

Microphone no longer works after upgrade to windows 8.1

After upgrade to windows 8.1 my internal microphone no longer works.
I tried installing updates suggested in other posts with similar driver problems but they did not work.
HPSupportSolutionsFramework-en-11.51.0048 did not work.
My internal microphone is IDT High Definition Audio Codec
When I go through the control panel and look at it - it shows a status of "not plugged in"
Please help
thanks

OK I am a little confused.
There has been no response on this subject in over a week. Not since I responded to your questions regarding product name and number.
However I just received the following email from you:
Hello gordml,
The questions you posted on the HP Support Forum recently received one or more answers.
Question: Microphone no longer works after upgrade to windows 8.1
Date: Sun Dec 21 01:01:56 PST 2014
View the answer(s).
Did this reply resolve your post or question?
If yes, then share the good news! Let others know this reply was helpful by accepting this solution.
You can also show your appreciation by giving kudos.
We appreciate your feedback. It's what keeps our community such a helpful, vibrant place for our members.
Thanks for being a member!
The HP Support Forum Team"
Why would this be sent to me if there has been no recent replies on this issue?

Re: NB200-134 - FN key not working after upgrade to Windows 7 Ultimate

My FN keys of NB200-134 is not working after upgrading from Windows 7 starter to Windows 7 ultimate. I tried installing every drivers found on Toshiba website for my lappy but still it does not work.
Help please

Hi asalamk,
The FN keys are controlled by Value Added Package and Flash Cards Support Utility. I think you have forgotten to install these tools
You should check the Toshiba page again and download both tools. Start with installation of Value Added Package then restart your notebook. After this install Flash Cards Support Utility. Once again restart and all FN keys should work properly now.

Macbook pro 13inch,mid2010 qwertyu keys don't work after upgrade os x Yosemite

macbook pro 13inch,mid2010 qwertyu keys don't work after I upgrade os x 10.10 Yosemite. but it works on keyboard viewer. I'm not sure if it's hardware or software problem, how can I fix it?

Hello there, kipolo.
Great job using the Keyboard viewer to troubleshoot your issue so far. The following Knowledge Base article provides a great checklists of steps to pinpoint the issue a bit further:
One or more keys on the keyboard do not respond - Apple Support
Some keys don't work as expected
From the Apple menu, choose System Preferences.
From the View menu, choose Speech.
Click the Text to Speech tab.
If "Speak selected text when the key is pressed" is enabled, the key or key combination set to speak text cannot be used for other purposes or used to type text--click Set Key and change it to a less-commonly used key combination (try to use modifier keys such as Shift, Command, Option, and Control). Or, disable the "Speak selected text when the key is pressed" option.
Click the Accessibilty or Universal Access pane in System Preferences, then click the Keyboard tab.
Make sure that Slow Keys is turned off. With Slow Keys on, you need to press a key for a longer period of time for it to be recognized.
In the Accessibilty or Universal Access pane, click the Mouse tab, and make sure Mouse Keys is turned off. With Mouse Keys enabled, you cannot use the Numeric Keypad to enter numbers--instead the keypad moves the pointer (cursor). (There is an option to enable Mouse Keys with five presses of the Option key; you may want to turn that option off to avoid accidentally enabling it.) If Mouse Keys is enabled and you are using a keyboard with no numeric keypad or Num Lock function, see Unable to type while Mouse Keys is enabled in Mac OS X.
If the function keys on the top row of the keyboard are not working as expected, see Mac OS X: How to change the behavior of function keys.
If the issue persists, use Keyboard Viewer to help isolate the issue:
Click the Language & Text pane (Mac OS X v10.6) or International pane (Mac OS X v10.5.8 or earlier) in System Preferences.
Click the Input Sources tab (or Input Menu tab in Mac OS X 10.5.8 or earlier).
Click the Keyboard & Character Viewer "On" checkbox to select it (click the Keyboard Viewer "On" checkbox in Mac OS X 10.5.8 or earlier).
From the Input (flag) menu, choose Show Keyboard Viewer.
If the keyboard is connected and detected by OS X, the keys you type will highlight in the Keyboard Viewer window. Open TextEdit (or any text application), and try to type something using the keys that were previously not responding to see if they highlight in Keyboard Viewer.
Start from the Mac OS X Install Disc, choose Terminal from the Utilities menu and test the keys which were previously not working. If the keys work while started from the Install disc, then the keyboard itself is working correctly. Use How to troubleshoot a software issue to isolate the software issue that may be causing the keys to not respond.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Bluetooth Not Working after upgrading to Windows 8.1

My Laptop is HP Pavilion G6 2015 tx after upgrade to windows 8.1, bluetooth is not working also the battery drain has increased anyone know a fix atleast for bluetooth problem ???

You're very welcome.
That is very interesting, because I didn't know of anyone who upgraded to W8.0 with a Ralink wireless card with the BT 3.0 radio that got the BT to work at all.
We tried the W7 drivers, and they didn't work.
That is why you don't see a W8 Ralink BT driver for the bluetooth on your PC's support and driver page amongst the other 11 drivers listed.
The Ralink 3.0 version of BT is not supported in W8.
While somehow the BT has worked in W8 for you, I'm afraid your luck has run out.
Unless by some fluke, HP installed a card with the BT 4.0 radio on your model...
You can try this W8 driver for the Ralink card with the BT 4.0 radio, but don't get your hopes up.
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5229457&sp...

Dolby Home Theater v4 not working after upgrading to Windows 10

Hi there, I just upgraded to Wndows 10 Home from Windows 8.1; everything went smoothly except for the fact that Dolby Home Theater v4 does not work. I had to reinstall it using the .msi file found in the Realtek Audi folders. I chose v4 over any of the other versions because I like how I can tune the equalizer to my liking and different uses. Anyways, the regular audio works and Dolby is turned on but there is no activity appearing on the equalizer and my music does not change once adjusted. Had this problem when doing an optional audio driver update in the past when I was running 8.1. I do not have the option to rollback the driver after upgrading to Windows 10. Does anyone have a solution to this issue or know what the correct Realtek driver is to make Dolby work? This is one of my favorite features of my laptop and I really want it up and running again! Thank you in advance! JakeStiebs My unit: Lenovo Ideapad Z580 running Windows 10 Home with Realtek Audio Driver 6.0.1.7535

one more thing. I was not able to download cleanup tool/online scanner too. but may be it has something to do with my internet bandwidth. and other strange thing i observed is that before restart i was not even able to turn off all security features. but after restart that problem seems to be corrected.

ThinkPad X240 WWAN not working after upgrade to Windows 10

Hi, My 3G Card stoped working after upgrade to Win 10.I tried latest drivers from Lenovo but with no success. When I open Device Manager the Card is shown as properly installed but the driver manifactire is Microsfoft not Lenovo/Ericsson When I try to reinstall the driver the installation package poppup a message 'No action was taken as a system reboot is required'On the network connections the Mobile Netork is disabled:after trobleshooting on the connection I recieved and error: witch code 36. Is there a solution available ? regards,stuckoff

Which Operator and Country SIM card you are using ?Error Code 36 is regular deactivation. Do a Windows update , Restart then Shut Down System and start ( TYhis Power cycles the Device ) . From your Screenshot it Looks like the Cellular Data is not ON and Microsoft cellular service is in some mismatched state after upgrade.After restart press like in below screenshot order 1 --> it turns cellular on or off, 2---> It will take you to settings page 3--> Connect from here. Dont ask why Microsoft made connecting to WWAN device so complex

Scanner of HP 8500 A909g does not work after upgrading from Windows 7 to Windows 10

After upgrading from Windows 7 to Windows 10 and subsequent upgrade of printer software, the scanner functionality did not work. When I tried to uninstall the printer software I got the message "HP uninstaller has stopped working". After another upgrade of printer software the scanner was still not working. How can I get around this problem? Update:
I followed the instructions for a similar problem with Windows 8 on http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/Scan-doesn-t-work-on-Solution-Center-after-migrating-to-Win/td-p/2228367.After this, the scanning seems to work. Not sure whether it is possible to uninstall, though (don't want to try since it is working).

I had the same problem with my Officejet Pro 8600 All-in-One scanner, sfter upgrading from Windows 8.1 to Windows 10. After uninstalling and then reinstalling the printer driver, the problem is solved. You can look up the model of your printer on HP's support site and download it from there. Apparently, not all printers are compatible with Windows 10. In that case, they recommend you buy a new printer. ;-)

Keyboard wireless key not working after upgrading to windows 8.1

Hello,
I am having hp pavilion dv6-6165tx notebook, where keyboard having a wireless button that turns ON and OFF all wireless devices, After upgrading to windows 8.1, HP Connection Manager is not getting installed, as well as Key is not working, key color turns red and white but no action is performed.
Kindly suggest me some solution.
Note: HP Doesn't provide drivers for windows 8/8.1 ONLY WINDOWS 7 for hp pavilion dv6-6165tx.
Thanks.

Hi @Jayesh_Bhadja ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6165tx Notebook and the Wireless keyboard not working correctly. Here is a link to troubleshoot the keyboard.
The HP Connection Manager is something that is for Windows 7 not Windows 8.1. I would uninstall this from your Notebook. Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating. It has a troubleshooting tool in this.
Make sure all your updates have been completed. I would try restarting my Notebook a few times.
If that does not help I would uninstall the keyboard from the Device manager.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Ethernet LAN not working after upgrading to windows 8.1

After upgrading from Windows 8 to 8.1, my Ethernet LAN is no longer working. Wireless LAN connectivity is OK. I have run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I do not see a 8.1 driver listed for the Ethernet LAN.

You're very welcome. See if the recovery manager still works so you can roll back to W8. Please read this guide for how to use it. http://support.hp.com/us-en/document/c03489643 If it doesn't then you will have to order a set of recovery disks from HP, or you can install this plain W8 OEM software this guy has posted on a link. Lots of folks have used it successfully, which is why I posted it. https://docs.google.com/file/d/0B0W9PBigPy94aVJWSndyTFNFMzg/edit?pli=1 Then use this tool to make the iso file bootable to a DVD or 4+ GB USB flash drive. http://www.microsoft.com/en-us/download/windows-usb-dvd-download-tool Yes, that really stinks why you and I could not upgrade without an issue. I disabled about 5 or 6 devices in the device manager and the code 12 would not go away. I have no clue why the PC works fine on W8 but not on W8.1. My notebook is a few years older than yours and it worked fine on W8.1 but not on W10. Go figure...

2015 HP Envy 23 Ips monitor with Beats Audio is not working after upgrading to Windows 10

Hi I have upgraded OS to Windows 10 recently. from then there is no sound from my monitor. FYI.. am ussing a Dell laptop to connect to the monitor witha HDMI cable. It was working fine before upgrade and suddenly it stoped working after the OS upgrade.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your notebook computer's monitor will not produce any sound after upgrading to Windows 10, and I would be happy to assist you in this matter! According to the available list of supported drivers for your monitor, there is currently no Windows 10 software published at the moment. In the meantime, I recommend following the steps in this document on HP Products - Where do I find Windows 10 drivers and software for my model? I also suggest connecting the monitor on a different computer to test the hardware functionality of the speakers. I hope this helps! Best Regards

Lenovo care don´t work after upgrade to windows 7

Similar Messages

Maybe you are looking for