Lenovo Flex 15 bootet nicht, Power LED blinkt

Hallo zusammen,
Mein Lenovo Notebook lässt sich seit gestern nicht mehr einschalten. Die Power LED blinkt dauerhaft jede Sekunde als wäre es im Stand by. Ob mit oder ohne Netzteil passiert nichts beim drücken der Power Taste. Einzige Veränderung, die herbei zu führen ist, ist dass beim abstecken des Netzteils nichts mehr blinkt, bis zum nächsten drücken.
Da der Akku fest verbaut ist habe ich schon alles andere versucht, um das Notebook kalt zu starten. 1 min die power taste gehalten, die recovery. Shift + power, fn+power... Alle Tipps haben nichts gebracht.
Auch der Support ist ratlos.
Soll es einschicken, mit dem Hinweis, dass zu 50% auch meine Daten weg sein werden.
Ein vorheriges öffnen würde zum Garantie Verfall führen...
Hat irgendwer noch Tipps?

Schön das es wieder funktioniert!
So wie es aussieht hat der sich einfach irgendwo verhangen. Problem ist halt das man den Akku nicht einmal kurz rausnehmen kann...
Würde an deiner Stelle erstmal ein Backup machen (sollte man ja ohnehin immer haben ) und ihn dann normal weiternutzen. Einschicken würde ich ihn nicht mehr solange du keine Einschränkungen feststellst, wird für den jeweiligen Mitarbeiter dann ja auch schwer einen Fehler zu finden, wenn keiner vorhanden ist

Similar Messages

Pxi 8360 power led flashes red

I have a PXI 8360 MXI Express board mounted in a PXI 1050 chassis. I am seeing the power LED occasionally flash red and I lose communication with the computer. The power LED will return to solid green status after a few minutes but I am not able to do much with NI DAQ to test the system since it has failed self test. The suspicion here is the power supply may be bad but how do we check that.
The system with the computer has worked well over the past several years and we are concerned about possible damage from a power fluctuation that happened here around Christmas time.

Hi Xavier,
The red flashing light is on the PXI 8360. I have not seen any flashing lights on the chassis.
The modules present in the system are
PXI 8360 MXI Express
PXI 4071 7 1/2 digit flex DMM
PXI 4110 Programmable DC power supply
PXI 4110
PXI 4110
PXI 8252 1394 Host Adapter
TB 2627 multiplexer terminal block
PXI 6289 M series multifunction DAQ
SCXI 1306
SCXI 1303
SCXI 1303
SCXI 1300
So far all testing has been done with all modules installed. Another person has tried reseating all modules to see if that would fix the problem but it does not.
The system will work fine for a few hours and then the blinking LED will begin and somewhere near that time the communications fail with the computer. The light will blink for a few minutes and then will return to solid green. Once the error has occurred it seems that the only way to re establish proper operation is to shut down the whole system, PXI chassis and computer, and restart. I saw one time where the power LED on the 8360 went from flashing red to solid green when the computer was turned off.
The computer is a Dell Precision 690 with PCIe 8361.
I will be opening up the chassis hopefully in the next day or two to check fuses and voltages where I can.
Bill

Lenovo Yoga 11s startet nicht

Hallo zusammen =)
Wie im Titel schon beschrieben, startet mein kleines Lenovo Yoga 11s IdeaPad nicht mehr.
Nicht mehr bedeutet folgendes:
Wenn der An/Aus-Schalter an der unteren Seite des Gerätes gedrückt wird, passiert für 2 Sekunden nichts (die Standby-LED geht an) und nach diesen 2 Sekunden fährt der Lüfter an der oberen Seite des Gerätes hoch und weiter passiert nichts. Der Bildschirm bleibt schwarz und der Lüfter dreht solange, bis ich das Gerät wieder via Shift + An/Aus-Taste "zwangsabschalte".
Da ich bei dem kleinen IdeaPad den Akku nicht rausnehmen kann, hab ich die Liste mit USB-Geräte entfernen, Akku entfernen, SD-Karte entnehmen etc.. schon durchgeführt - ohne ein erkennbares Ergebnis.
Ich hoffe, dass man mir hier weiterhelfen kann =)
Mit freundlichen Grüßen
Hügli

Hallo Hügli,
lass das Yoga einmal in diesem Zustand komplett leerlaufen bis es von selbst abschaltet. Wenn es dann auch in keiner Weise mehr auf den Einschalter reagiert, halte diesen bitte 10-15 Sekunden gedrückt.
Lade dann den Akku erstmal mindestens eine halbe Stunde und schalte das Yoga dann ganz normal wieder ein.
Wenn das auch nicht geholfen hat, bleibt nur noch der Weg, das Gerät über den Support einschicken zu lassen. Rufnummer oder Mailformular findest du hier: http://support.lenovo.com/de/de/contactus
Gruß - Sebastian
→ Wenn Du eine Lösung auf Deine Frage erhalten hast, markiere diese bitte als gelöst - Hilfreiche Beiträge verdienen Kudos. Zögere nicht Kudos zu vergeben.

Lenovo Flex 2-15 notebook monitor

I bought a Lenovo Flex 2-15 notebook months ago but it has not been used much. I sat in my roommates room on a dresser. As far as I know it has not been dropped or fell off any thing. However, when I was going to use it last week I seen that the monitor was separated and i seen a white wire sticking out the top. the touch screen still works but I am afraid to use it. Need to know if there is a way to fix it or do i need to send it to be fixed or buy a new computer. please advise. Jamie Coley

Hallo Mischu123,
das wird leider nicht gehen, da du versuchst eine Art "Zelt-Modus" umzusetzen, der für das Gerät einfach generell nicht vorgesehen ist.
Um da auch jegliche Schäden am Gerät zu vermeiden, wird die Tastatur dort geblockt, damit das ganze Notebook gar nicht erst so hingestellt wird.

K450 bootet nicht mehr

Hallo hallo,
nachdem mein neuer K450 erfolgreich auf Win 7 lief nun der Supergau, das Teil bootet nicht mehr, keine Ahnung warum. Er kommt nur noch bis zum Lenovo-Screen und das war's, kein F1 oder F2 möglich, kein Booten von CD möglich. Es liegt definitiv nicht am USB (wie im englischsprachigen Forum beschrieben), ich verwende keine externe HDD, beim letzten Shutdown befand sich auch nichts in den USB-Slots. Die Startreihenfolge im BIOS wurde auf CD - Festplatte festgesetzt, USB nicht in der Startreihenfolge vorhanden.
Irgendwer eine Idee???
Danke für Hilfe,
Alex
Gelöst!
Gehe zu Lösung.

Hallo Alex,
versuche erst einmal eine simple Reststromentladung:
- PC ausschalten
- alle Peripherie und das Stromkabel abziehen
- wenn am Netzteil ein I/O-Schalter ist, den wieder einschalten (auf I)
- Einschaltknopf vorn gedrückt halten (mindestens 15 Sekunden)
- wenn am Netzteil ein I/O-Schalter ist, den ausschalten (auf O) - Stromkabel + Peripherie anschließen - Schalter wieder auf I
- PC einschalten
Wenn das nicht geholfen hat, schau bitte, ob im BIOS der Boot-Mode noch auf "Legacy" steht, wenn du Win 7 vorher in diesem Modus installiert hattest. Eventuell wurde nach einem BIOS-Update dort wieder UEFI-Boot eingestellt.
Gruß
Sebastian
→ Wenn Du eine Lösung auf Deine Frage erhalten hast, markiere diese bitte als gelöst - Hilfreiche Beiträge verdienen Kudos. Zögere nicht Kudos zu vergeben.

Lenovo Flex 2-15 Rotation ausschalten

Hallo Zusammen, ich würde gerne die Rotation bei meinem Lenovo Flex ausschalten.Ich hatte schon eine Anleitung gefunden, aber leider hat das nicht funktioniert. Folgendes habe ich schon probiert:1. angeblich kann man die Rotation bei der Helligkeit abschalten, bei mir gibt es dort jedoch nicht diese Funktion2. über Bildschirmeinstellungen soll man unter "Orientierung" eine Option zum Ausschalten finden, ist dort nicht3. ich habe schon die registry unter HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\AutoRotation auf 0 gesetzt. Hat auch nicht funktioniert.Die Treiber habe ich aktualisiert.Zu Beginn war der Sensor nicht so empfindlich, jetzt nervt es aber wahnsinnig, da man wirklich nur auf einer geraden Tischplatte arbeiten kann und nicht auf einem Notebook Kissen etc. Wäre toll, wenn mir jemand helfen könnte. :-) Danke!

Hallo,
bitte mal folgendes versuchen:
1) Rechtsklick auf den Desktop, in einen freien Bereich.
2) Dort Bildschirmauflösung wählen.
3) In den angezeigten Einstellungen sollte es eigentlich eine Option geben, die "Automatisches Drehen des Bildschirms zulassen" heißt. Diese dann abhaken.
Alternativ funktioniert bei einigen Geräten auch das Kürzel "Windows-Taste" + O (der Buchstabe)

Flashing power led on c200

Hi, I am new to the forum but I have looked for an answer before posting.
My laptop specs are: Lenovo 3000 C200 8922 5YG (OS not important)
My problem: If I insert a battery while using my laptop it turns off. It will restart, but when I restart it uses the battery even though it is plugged in to AC.
(extra info -
If AC only, works fine, solid green power led, no battery led....
If battery only (new battery, old one is fully discharged), works fine, solid power led, solid green batter led ...
If AC and battery, works fine, but not charging, running on battery, solid green battery led, BLINKING green power led...
Removing battery switches off laptop, even if AC attached, inserting battery switches off laptop when using AC...
Battery will not charge even if laptop turned off but battery and AC still inserted....
end of extra info)
Because it switches to battery, obviously my battery will not charge, (neither new battery or old one).
I presume this is related to my question, I have read all the manuals and searched on-line but nowhere can I get any reference to the power led flashing or blinking on this model. Even in troubleshooting no mention is made of the possibility.
Does anyone have any idea what a flashing power led on a 3000 C200 indicates please?

the warranty is out of date, this is a used machine and it seems that it has had a VERY tough life. I nursed it back to life as a project . It was in a very sorry state with much damage to plastics and basically dirty and abused. I have completely dismantled it and rebuilt it. I thought it was maybe the battery, so i bought a new one!! I guess it is a failure in the charging circuit somewhere so I am using it as a non portable desktop machine. I guess some things are better left to die
Anyway, I was curious about the behaviour of the flashing LED as I couldnt find any reference to it.
Thanks for the responses though.

T400 Power Problem: Flashing AC Power LED, No Battery Charge, Screen Flicker, No AC Boot

I bought a refurbished T400 less than 3 months ago. Today the power status change beeps started going off every minute or so, the power indicator light went off (while plugged in) and the battery began discharging. At the same time, the screen started flickering.
I powered down and tried draining the static by using the old trick: removing the battery and ac plug and pressing the start button 10 times and then holding on the 11th try. Didn't solve the problem.
When I use battery only, the screen doesn't flicker.
Plug in power and the screen starts flickering again, with the power LED mostly off but occasionally flickering on briefly.The battery is not listed as charging. Nothing to indicate that the power is plugged in, except for the occasional flash of the LED and the power status change beeps.
When I power down again and stay plugged in both the power LED and the battery LED keep flashing. First both are flashing green, but in a few minutes the battery light turns flashing orange.
If I remove the battery, both LEDs keep flashing. Try to power on that way and nothing happens - the LED's keep flashing, but it doesn't power on at all
Battery is new (the first one shipped wouldn't hold a charge at all; this one lists as good condition).
I don't have another Lenovo power supply to try, but the current one doesn't appear damaged or bent at all. I tried jiggling it while plugged in and there was no change.
The last thing I did before the problem began was remove a scanner from the usb port. I heard the thinkpad ports were fragile, so I am always very careful and gentle when using. I cannot see any damage to the ports.
I have about 70% battery charge left to work with, according to power manager.
My 30 day warranty is over, so I either figure this out, or I'm out the purchase price of $260., which I know is cheap for a replacement laptop, but a lot for only ten weeks of moderate use.If it's the motherboard I don't think it would be worth replacing - am I wrong? But what else can it be?
Any troubleshooting suggestions greatly appreciated. Please help! Thanks in advance for reading.

Thank you so much for the quick reply. It is a fake adapter - no lenovo written anywhere.
Now what? Should I test the unit with another adapter, or check the output of the adapter?
I hope that is the only problem, that would be wonderful. I'll update when I know more.

Battery life lenovo flex 14 - does not last long at all! (2h30)

Hello , I got a lenovo flex 14 last september so it's very new.
The battery lasts only 2 hours 45 when charged fully. I find it too short considering the computer is new and the battery is supposed to last between 5 to 8 hours on a lenovo flex 14.
I am very average user. i am listening to music, typing word document, searching on the internet..
I have already checked in task manager and no application seems to be running and "" eating" the battery.
Do you have a similar issue to mine?
Thank you for your help. I am wondering if my battery is defective...

Me too im regret to buy apple product. Battery NO GOOD

Lenovo Flex 2 15 warranty is incorrect

I bought my laptop on November 11th, 2014. I bought it at Futureshop in Canada. I looked up the warranty status and it has the wrong date on it.
I have called 2 times and they said it would be fixed in 24 hours. Today I check and it is still the incorrect date.
Can someone @ Lenovo fix this? I can show you the receipt.

I have a Lenovo Flex 2-15, and I want it to startup with Mozilla Firefox, but it opens Firefox as it is set to do in my startup file, but then it goes to Internet Explorer. I think this must be a Lenovo thing, because know of someone else who has same settings, but they do not have this problem. IE is not responding at this time, so it is a pain to get out of it. Anyone know of any Lenovo settings that could be changed that override the startup instructions? Or does anyone else have similar problem? Help would be GREATLY appreciated.Thanks!

No wifi connections with Windows 8.1 on Lenovo Flex 2-14

I got me a new Lenovo Flex 2-14 with Windows 8.1 on it yesterday, but I can't connect to my wifi network. In the tray there's always the red cross (not the yellow symbol) and no network is found at all.
I read that a lot of users experience this, so I tried multiple drivers but none of them works. I tried the one pre-installed on the D drive, the newest one from the Lenovo website and also some that I found via Google when I searched for my wifi-adapter (it's a Realtek RTL8723BE). But as I said, no driver works.
Does anybody have an idea what I could do? It's a completely new notebook, so I didn't change any settings.
Thank you!
Solved!
Go to Solution.

Actually I have no idea what wireless adapter I have, on the Lenovo page both drivers are listed. When I install the Realtek driver I at least see an entry in the Device Manager, whereas when I install the Intel driver nothing happens at all. I deinstalled the Intel Tools and reinstalled the Realtek driver afterwards, but nothing changed.
In my router's settings I can only choose between channels 1 to 13, as far as I know these are at 2.4 GHz, right?

Mac Pro will not boot. Power led just flashes

When I start up, the HD spins but then the power led starts flashing at a constant rate. It also never gets to the gong. I tried everything on the support pages.

Power On Self-Test Beep Definition - Part 2.
It would be helpful to be more specific about the flashes such as the sequence, timing, etc. So, you will need to examine the above and its links to see if you find something descriptive of what you have.

HP Envy 15" TouchScreen Power LED shows up, but fans not running and screen does not come on

Hello there!
I am a 1A Software Engineering student at University of Waterloo, and I am running into a very serious problem with my HP Envy 15" TouchSmart laptop running Windows 8.1. This is a problem that just started today, and I would rather get some support from here first before I go see the technical support office sometime tomorrow; it has to do with the screen and fans where the Power LED lights up white, just as when the laptop is running properly.
(I do have warranty on the laptop since it was bought last June, except that if I find out I need to get a replacement, I'll lose all of my work I've been doing on it ever since I started my semester. It's so ridiculous of me to not have all of my work saved on a backup, as I do have an external hard drive. Trouble is, I got way too many problems in getting myself organized, I am not being open-minded as I should, and worst, I am not finding a balance between homework and life.)
Before I had my MATH 117 (Calculus 1 for Engineering) lecture, I was in a lab nearby where my laptop was opened and turned on, functioning properly. I had NetBeans IDE running since I wanted to work on the second part of my current CS 137 (Programming Principles) assignment. Because it was almost time for my lecture, I closed the laptop by simply moving the screen back down onto the keyboard, where it goes into sleep mode. (Anytime I flip up the screen, the laptop is supposed to come back on, and the login sliding screen from Windows 8.1 shows up.)
When I took my seat for the lecture, I wanted to spend a little bit of time to work on my programming assignment. However, upon flipping the screen back up, instead of having the login screen show up, I encountered the problem: the Power LED is showing a white light, but I can't hear the fans running from the vents on the left side of the laptop, and the screen does not turn on. I did try to hold the power button for several seconds, and once at least 10 seconds, except that the Power LED keeps on showing a white light. The light for the Wi-Fi board does not show up.
Whatever it is, I don't want to pull the battery out because I did do that on my last laptop, and it was from there that I couldn't turn the old one back on again. If I pull the battery out from the Envy laptop, it'll short-circuit the connections from the battery to the computer, and thus several components will fry. For now, what I'm doing is leaving the laptop as is to drain the charge on the battery. And then, once I notice that the Power LED does not show a white light anymore, plug the AC adapter, then try turning the laptop back on using the Power Button.
It's going to take a little while for the circuit to drain the charge on my battery though...
Anyway, would you please be so kind as to help me out with this issue? I would really appreciate it if you can give me several recommendations. Thank you!
This question was solved.
View Solution.

Hello @GregPDesWHP,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer is not powering on, and I would be happy to assist you in this matter!
In order to regain functionality of your computer once again, I recommend following the steps in this document on Computer does not start (Windows 8). If the issue continues after exhausting all of the steps in this document, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Lenovo Flex 10 touchscreen stops working after 1 hour of use.

Just bought a new Lenovo Flex 10 from a retail and it works perfectly except that after an hour of use the touchscreen stops working, the computer still works ok, but only with the mousepad. The notebook came with Windows 8.1, and I haven't installed any program on it. I need an urgent response please, since i've been looking for days in the community and other support pages, and still can't get a satisfactory answer and the period to get the a refund are about to expire.
Thanks in advance.

hi riglesias,
Welcome to the Lenovo Forums.
Once the Touchscreen stops responding, can you check the following:
1. Open System Properties and see if the Touch functionality is still there
- Link to picture (Touchscreen feature is not detected)
- Link to picture (Touchscreen feature is detected)
If the Touchscreen feature is detected, proceed to Step 2.
2. Press the Windows key‌ +R, type devmgmt.msc and press Enter. On the Device Manager, navigate to the Human Interface Devices section and uninstall anything that says HID-compliant device (this is the driver that controls the touchscreen). When finished, reboot the system and observe.
3. If the Touchscreen is still not working, hold the Shift Key and hit the restart button inside Windows and you should be able to see the image below then try to tap on the screen to test and observe. I
If the touch capability is still not functioning, I recommend you contact lenovo for service.
- Link to picture
- Support phone list
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Lenovo flex 2 can't connect to samsung LCD tv by HMDI

I got a problem te connect my Lenovo flex 2 to my Samsung T200HD tv. wen i connect it says no signal... and yes i know i need to activate it from my computer. the thing is t doesnt find it. it says connect to screen by VGA... I dont have a VG poort, and i have no option to change it HDMI. The support desk of samsung say it my laptop software.... The thing is.. when i connected my laptop with the same HMDI cable to a other Samsung tv it works instantly. I have tryed all kinds of things and lloked on forums.. nothing worked... not updating the drivers... not reinstalling them.. i think its the combination between the useless Intel HD software and the Geforce software... Does anyone has the same problem and a fix!

Update:
I can connect through the IE Tabs extension on Chrome. In other words, when Chrome simulates an Internet Explorer browser tab, I'm able to connect. I'd still like to find a fix for this problem since I can't configure Outlook. Can anyone help me out?

Lenovo Flex 15 bootet nicht, Power LED blinkt

Similar Messages

Maybe you are looking for