Lenovo g510 100% still charging

Hi,
i just bought a lenovo g510. Everything seems to be fine, except that after the battery is still charging after 100%.
I got the same message on windows 7 and 8.1,  : 100 available (plugged in, charging)
the icon in the bottom right of the screen shows me the current cable is connected.
may damage the the battery? What should i do?

after i spet some time searching infos about this.. i found this: http://forum.notebookreview.com/sony/65055-sz-battery-fully-charged-still-charging-revisited.html
i installed http://www.passmark.com/products/batmon.htm and i watched the charging rate after the battery hits100% 
and I noticed that the loading rate was declining. After about 10 min loading rate dropped to 0 and the message displayed by Windows was fully Charged 100%.
mention that I installed 64 bit and Windows 8.1 software for energy management is the cd that came with the laptop.

Similar Messages

  • Lenovo G510 won't start when battery is on and it's fully charged

    Hi there. I have my Lenovo g510 i5 notebook for 10 months, and my battery is wrong. I haven't used it on battery too much, but when I used it, I empty all of it and then charged it when it's turned down. Couple of days ago, the battery was empty I put it to charge, the orange light appears that it's charging, and day after when I put the battery on the notebook won't start, but with the battery and adapter start normally and show that the battery is 100% (fully charged). Why I can't use it on battery? Please help me.

    Hi Kocevski_91,
    Welcome to Lenovo Community!
     As per the query we understood that you are facing issue with system not starting with battery in your G510 laptop.
    Please remove the battery and connect only adapter and check for the issue, also try to perform a power drain by removing all the external devices connected to the devices and shutdown the system, now remove battery and adapter, press and hold the power button for 30 seconds, connect battery and adapter and check for the issue.
    If still the issue persist, perform battery gauge reset, go to power manager select advance mode and select battery tab and click on battery maintenance under this option click perform under battery gauge option. Please perform and reply with results.
    Hope this helps. Do post back if issue persists!
    Best regards,     
    Ashwin.S
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Lenovo G510 Inaccessible Boot Device and Internal Empty Port 5

    Hi! I´ve got a lenovo G510 Laptop and I´ve been having several issues lately with it. First, it sometimes does not boot (a blue screen saying  Inaccessible Boot Device appears on the screen). On the other hand, there are moments when the DVD recorder is not recognized either on windows or BIOS. (On Intel Rapid Storage there´s a SATA disk for the OS and instead of recognizing the DVD recorder it says Internal empty port 5); but this is not always, just sometimes. Is it possible for the two problems to be conected?Best, 

    To me that sounds like a harddrive is getting ready to, or has, totally failed. If this is a new laptop or the warranty is still good, I would contact customer support and see if you can get it fixed.
    Hoov
    Microsoft MVP - Consumer Security
    SpywareHammer.com

  • Lenovo G510 Graphics Cards Driver Problem

    Hi!
    I just bought the Lenovo G510 Laptop, with an Radeon 8750, and installed Windows 8 64 Bit.
    After installing the drivers from the provided CD, I get the following Bugcheck error code in WhoCrashed
    0xA0000001 (0x5, 0x0, 0x0, 0x0)
    when rebooting ,or when I try to open the Catalyst Control Center.
    Actually the AMD graphics card driver seems to be responsible, as this problem does not occur until I install this driver.
    I tried to use the driver provide at the Lenovo support page too (for both Windows 8 and 7), with the same result. The ThinkVantage System Update does not install an AMD graphics driver at all.
    Accordding to WhoCrashed atikmdag.sys causes this error.
    I would highly appreciate any help!

    Hi Aimor,
    Welcome to Lenovo Community Forums!
    I’m sorry to hear that the Wireless driver is not getting installed in your G510 Laptop, I suggest you to download a fresh copy of the driver from the below mentioned link and while installing the driver right click on the downloaded file and select “Run as administrator” option to get it installed without any error:
    WLAN Driver (Atheros, Broadcom, Realtek) for Windows 7 (32-bit, 64-bit)
    Do post us back if the issue still persists.
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Lenovo G510, i5 - Problems with booting Windows 8.1 from media disk

    Hello,
    I know that some of you got into this little trouble too, so please help me out.
    Yesterday I got a brand new Lenovo G510, i5, with free dos and tried to install the Windows 8.1 from a media disk.
    The problem is that it won't boot from CD.
    I got in Bios using the Novo button, changed the boot mode from legagcy support to UEFI and nothing happend.
    I tried the boot mode to legacy; boot priority to dvd and still won't do it.
    It is still trying to boot from the network...is this posible?
    How can I get it to boot from CD/DVD?
    Some help, tips, indications would be great!
    Pretty please 
    Thanks a lot,
    Irina

    hi Rurulinda,
    Welcome to Lenovo Community Forums!
    Boot again inside BIOS
    Try setting these
    Under Exit TAB
     OS Optimization or OS Optimized Should be set as Disabled or Other OS
     Under Boot Tab / Start up Tab
     Boot Mode Should be set to Legacy
    Boot Priority Should be set to Legacy First
    UEFI Boot should be set to Disabled
    Quick Boot Should be Disabled
    Secure boot Should be Disabled
    Now press F10 to save everything and Exit
       Computer will Restart now inster your CD / DVD Disc in and Turn Off the Computer.
    Now on OFF state
       Turn it back on and Start tapping F12
           This will give you a boot selection with your DVD / CD as an option to boot from.
    Hope this helps
    Cheers!
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Adding SSD Hard in Lenovo G510

    Hi ,
    I have bought Lenovo G510 with 1TB hard core i7
    I want to add SSD hard with it.
    How i can add hard. Is there any way to add SSD Hard
    THanks
    Solved!
    Go to Solution.

    hi shanalikhan,
    Looking at the bottom, the G510 only has one HDD bay.
     - Link to picture
    In this case, it's still possible to add an SSD using the following options:
    Option 1:
    - Remove the stock 1TB HDD and replace it with an SSD
    - Use a 2.5" USB SATA Enclosure to convert the 1T HDD into an external drive.
    - To install Windows on the SSD, you can either clean install a retail copy or migrate the OS from the HDD to the SSD.
    Guides:
    - OS Migration (using Paragon Backup & Recovery Home)
    - Disk Cloning (using Macrium Reflect)
    Option 2:
    - Remove the ODD and replace it with an HDD caddy. From this thread, there are users who have successfully done this procedure. The HDD caddy that was used is this item.
    - To install the OS, you can follow the same guide above to either migrate or clone HDD to the SSD and make the SSD as the boot drive.
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Problem with AMD and Lenovo G510 Notebook

    Hello,
    I bought a Lenovo G510 Notebook i7 with both Intel and AMD Radeon 8570 graphic cards and I have to say my (first and only) experience with AMD and Lenovo is being so far totally disgusting.
    My problem is that there's no way I can make the computer use the AMD Radeon while playing, I updated the drivers (even following instructions from Lenovo Staff in this forum) and there's no way to do it. I updated it from AMD and Intel webpages and neither works. Right now I have the latest drivers from Lenovo webpage and the computer can't even recognize the AMD graphic card (in Device manager is written as OPAL GT/XL 6604).
    I don't know what else to try, I've been trying to look for more solutions in the websites but I have to say they are for me totally a mess and the only thing I got was "update your drivers" once and again. I hope the service is better than the offered in the website.
    Diego

    Can you tell me what Windows version are you using? And some other information.
    For example:
    G510
    i5-4200M
    4GB
    500GB
    Fresh Windows 8.1 Pro Update 1 x64 (means I did not update but installed fresh after formatting all partitions)
    Intel HD 4600 & AMD Radeon HD 8570M
    Also post a picture of your Device Manager with Display adapters expanded.

  • Anyone having same problem? I phone 4 after updating to Vers.5.1.1. battery cannot be 100% full charge, always stop at 99% and battery drains off fast too :(

    Anyone having same problem? I phone 4 after updating to Vers.5.1.1. battery cannot be 100% full charge, always stop at 99% and battery drains off fast too

    I had major issues with the iPhone 4s battery, however it’s resolved.
    The tech who set the phone up at the Apple store did so with little training.
    if you have a mobile me account. First go and move all your data to the cloud by going on your computer and logging in at me.com/move. The cloud has replaced mobile me, so there is no need for those two accounts
    Also make sure that for any of your email accounts you set them up to fetch, not push. My tech person set them all to have the email servers push data to the phone. The new iphone4s antenna is extremely strong so it will continually try to access stuff that is pushed–***** a lot of battery life doing this. It makes it worse if you have exchange 2010 accounts. Something about changes made to exchange really suck battery life from devices that access such accounts.
    turning of locator and the push notifications from facebook--they have a lot!

  • My Ipod Touch is not recognised in itunes or my computer but still charges, Please help

    My Ipod Touch is not recognised in itunes or my computer but still charges when connected via USB Please help

    Did plugging it into another USB port do any good? Make sure it is a USB port on the back of your PC and not via a USB hub or one on the front as they sometimes do not output enough power for the iPod to properly communicate with your PC.
    Do you have another 30 pin dock connector cable around you use to try and rule out a faulty cable? 
    Did you try a hard reset of the device with it still connected to your PC?  To do this, press and hold both the Sleep/Wake and Home buttons together long enough for the Apple logo to appear.
    With the article above were you able to verify that the Apple Mobile Device Service was installing and running on your system?
    Lastly, try plugging it into a different PC to see if it is recognized there.  It can help narrow down whether it is an issue with the iPod or with your PC.
    B-rock

  • Lenovo G510 - High temps

    Hi forum, i bought this laptop one and a half months ago and i notice that the temps are getting higher than normal.
     When its idle it sometimes drop to 28C which is the lowest ive seen but usuallly is about 36C. When i open Skype, facebook game etc it can hit 83C with no reason. The cpu usage at that point is bearly 18%. My first thoughts are same, the fan is not kicking when i has to and makes the cpu run hot and then unable to cool it as  much as it should.
    I hope someone help us because i started to get annoyed, i cannot stress the laptop atall. Even when i play a game in facebook i can hear the fans rpm increase.
    www.postimg.org/image/nsrxsavz1/
    Is there any update that can fix this? cause its no dust or thermal paste issue and ofcourse no applications are running
    According to :
    http://www.notebookcheck.net/Lenovo-G510-Notebook-​Review.117221.0.html
     The G510 graphics core always clocked at full speed in the stress test (Prime95 and Furmark run for at least one hour). The processor only ran at maximum speed in AC mode (2.9 GHz). When performing the stress test in battery mode, the CPU clocked with 2.5 GHz. The CPU's temperature settled to approximately 69 °C in the stress test (AC mode).

    Check temps with hwinfo.
    With tmonitor you can disable turbo boost which is a manufacturer hardware overclock and monit temps

  • Lenovo g510 poor performanc​e

    I have bought laptop Lenovo g510 series, i want to play some games on this laptop, but i cant run them on good graphics. It is impossible to run and play some of the new games. Help me configure my laptop, please. Also the fan is making noisy all the time, even i stay on desktop with no running process. The specs of the laptop are very good  : 
    Windows 8.1 
    RAM  8 GB 
    HDD 1 TB 
    Video Intel graphics + amd radeon r5 m 200 series - 2 gb 
    CPU Intel core i5 

    Hi Immitrofanov,
    Welcome to Lenovo Community!
    As per the query we understood that you are facing issue with poor graphics in your G510 laptop.
    Try to update the graphic driver and check for the issue.
    Click here for the driver.
    Hope this helps. Do post back if issue persists!
    Best regards,       
    Ashwin.S
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • My iPod nano 6th gen is not recognised by my computer or itunes, but still charges?

    My laptop recently came back from repairs and  wiped everything off of it, so I have had to reinstall everything again. The only way I have got my music is on my ipod, so I cant lose any of the music stored on the ipod.
    I have tried everything to connect it to my laptop, but it just wont connect.
    I have followed all instructions from other people who have had the same problem, but nothing works. I have tried uninstalling itunes, where I delete everything and reinstall it. I have tried uninstalling all my usb ports and reinstalling them. I have tried to download apple usb driver, but it didn't work. I have reset my ipod many times - but nothing works! My computer just wont show my ipod, but it still charges it.

    And you have a tried a different USB cable to verify that the current cable is not faulty or damaged? If so, that points to a hardware issue with the Nano, likely its dock connector port. Look for signs of damaged/bent/corroded pins or debris that could be blocking a proper connection.
    B-rock

  • My ipod touch used to sync on my old Hp laptop but now it's not even recognized as a device but will still charge on my new asus windows laptop. Itunes on my old laptop is missing something and won't work and I've reinstalled itunes on the HP already.

    My ipod touch used to sync on my old Hp laptop but now it's not even recognized as a device but will still charge on my new asus windows laptop. Itunes on my old laptop is missing something and won't work and I've reinstalled itunes on the HP already. Could somebody please help me to get my ipod touch to sync on the Asus laptop please?!

    Hello hieunguyen2012,
    The following article can help get your iPhone to appear in iTunes on your new laptop.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Cheers,
    Allen

  • My iPod Touch is not being recognised by iTunes or my computer, yet still charges. I have done EVERYTHING.

    When I plug my iPod in, my computer makes the 'ding' noise. However, neither the computer or iTunes actually recognises that there is anything there, yet it still charges.
    This iPod is BRAND NEW. I havn't even had the chance to ACTIVATE it yet. I installed the latest version of iTunes. I have tried THREE different USB cords, and EVERY USB available. I have restarted my computer. I have restarted the iPod. I have waited until it was charged. I have spend about HOURS going through Apple Support, and looking up alternative solutions from people having a similar problem. Most of their problems were fixed by wiping the iPod... mine isn't even activated yet.
    Solve this one, Apple. WITHOUT sending me a replacement.

    Is iTunes version 11 installed? Just do not say latest.
    Did you try everything here?
    iOS: Device not recognized in iTunes for Windows
    including here
    Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
    If you  have iTunes 11 turn on the Sidebar. Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar. The sidebar is where Devices appears. and Control+B to show the Menu bar
    Next try another computer to help determine if you have an iPod/cable or computer problem
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • Ipod not being recognized but still charging

    I've had my 60 gig ipod for about two years now. I tried connecting it the other day to charge and add songs to it when my computer says that the device has "malfunctioned" and cannot be recognized.
    I disconnected and tried again but no luck. It still charges,it still plays music,but itunes and windows choose not to recognize it. I tried 4 out of the 5 "r's" because of course i can't restore my ipod without itunes.
    I also tried the other ipods I had in my house and they all worked perfectly fine.
    Any suggestions as to what i can do?

    We're having a similar issue with a 30Gig 5th Gen on Windows XP. The only difference is that the battery was completely dead when initially attached and we didn't get the malfunctioned error. We've tried it on different computers (one with iTunes 7.x and the other with 8.x) with the same results.
    Have tried resetting (menu/select) numerous times, as well as going through the diagnostic (both manual and automatic). Can't seem to find anything wrong in the diagnostics.
    The device now has a full charge, and still won't be seen by either Windows or iTunes.

Maybe you are looking for

  • Custom file chooser

    Hello, I need to design a custom file chooser. Infact, I cannot call it a file chooser, because this is not accessing local system files. I am uploading some files into a directory using ASP and I keep that file name in the database. I can even uploa

  • Acrobat X Reader / Pro Issue with Window border resizing / flickering

    I have installed Acrobat X Pro and Acrobat X Reader on a new computer.  This is the only program on my entire computer that has problems. The problem occurs only with the menu bar (F9) displayed and when a PDF document is open. When resizing the wind

  • Is there a way of reinstating the scrolling options before ios9 was installed?

    is there a way of reinstating scrolling options before ios9 was installed?

  • Map the hierarchical queries pseudo column level

    Is it possible to map the hierarchical queries pseudo column level in the Workbench? I have an object for which I use connect by queries. I would like to map the pseudo column level. is this possible? if yes, how If the mapping is not possible how do

  • Parallel sequence - scheduling operation

    Hi, when I was creating parallel sequence in routing I was faced with problem in scheduling operation. After making a routing with parallel sequence, which are executing on the others work centers, system doesn't take into consideration the fact that