Lenovo H500s stuck at Lenovo logo boot loop

I've never had an easy use with this PC eversince I purchased it. It first rejected Windows 7 to be installed due to BIOS incompatibility which I had been warned before. I flashed the new BIOS version shared across the forum that worked for some people, it worked for me too.
 
Then just yesterday when I turned it on, it went into Lenovo logo for few seconds then restarted. It kept repeating the boot loop before I ran the power down to shut it completely. Already ran a system diagnose but found nothing. This already occurred before when I had to perform a windows fresh reinstallation for a constant fix, it runs normally for couple of weeks till yesterday when the problem came back.
 
Any ideas on what to do in this situation ?

Hi Warnbroom,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system stuck at Lenovo logo in your Lenovo H500s laptop.
Try to remove the hard drive(HDD) and check for the issue if the system is able to boot to BIOS.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

Lenovo K910 Stuck on Lenovo logo

I have lenovo with recovery and oryginal software(4.2.2). Today I want to enter to recovery CWM. I restart phone and make mistake. Instead to push volume+ I pushed volume+ and volume- together. Now i stuck on lenovo logo, i try diffrent combination of buttons but still I have logo of lenovo. What shuld I do ?

Press combination of Power + Volume down button after a vibration release the power button keep holding the Volume button its should entering the recovery mode.. good luck.

Lenovo g510 stuck in lenovo splash screen

I bought this g510 less then a year ago without an OS.
I've installed win7 first then ubuntu14.04, back when i get it.
Yesterday I deleted my win7 partition and reinstalled a premium sp1 win7 version from a usb formatted as NTFS - as you might have guessed I'm booting the laptop in legaci mode. The installation got stuck and failed and i had to do a hard reset.
After the hard reset the laptop won't boot and in fact it won't even pass the splash screen or respond to fn+f2 or any other shortcut to get into the bios. Even when i shut it off and press the Novo button it starts but doesn't display the blue utility menu with bios and boot options. Ive tried pressing the power button for 30 seconds witn the battery and power cable disconnected and tried to boot from usb but still nothing.
I then took the hard drive out and the laptop would boot and respond to novo button and fn+f2 and i can go into bios. It would also boot from usb when the hdd is disconnected. But it dosen't matter which bios settings i change or if the bootable usb is connected, when i hook the hdd back the laptop will just get stuck on lenovo splash screen again and won't respond to Novo button or fn+12 and it won't boot from usb - i should mention it does respond to capslock or the key to make the screen black (fn+f9).
I have a 1TR samsung sata hdd that seems to be perfectly fine. I don't think its the hdd or any of the hardware and the symptoms are not of defected hdd or anything else i've seen before. It 's also not a uefi problem as i've tried legacy and uefi mode with the same results. Also my usb boot is enabled in the bios just in case you're wondering.
This has ruined my weekend and about to ruine my week. Help lenovo please save me....?!?

hi markwills,
Welcome to the Forums.
If using another drive works fine on the G510 then I suspect that the stock HDD is failing or has corrupt partitions.
Can you consider using a 2.5" SATA enclosure to convert the stock HDD into an external drive and try to format the drive and/or run a hardware scan on it using the following:
- Lenovo Storage Test or
- HD Tune.
- http://www.hdtune.com/faq_1.html
When finished, try to insert it back on the G510 and observe.
If you get errors on the scan or if the above step is not possible, I recommend you contact warranty support on how to go about getting the unit serviced.
Support phone list
Similar thread:
G500 stuck on lenovo screen
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Ipad stuck in apple logo reboot loop to home page and then goes off

my ipad2 stuck in apple logo to home page rebooting loop and cant charge to 100%

Mine is doing the same thing and won't charge. It stays at 2%....this happened suddenly.

IPhone 4s stuck in apple logo reboot loop

I have an Iphone 4s, iOS 7.0.2 ,two days ago it hanged with newshunt apps after that i switch off my mobile but then it went into the apple logo reboot loop. I conected it up to my PC, and and the phone stayed in the reboot loop. I had to force my phone into recovery mode ,PC recognized it. I click "restore Iphone" and the process starts. get the following screens
last i got the following message
In my iphone screen, completed one loading bar But after that it brings up the Apple logo reboot loop, Please help

I also discovered that If I push it to DFU and then use Recboot to exit it it will show 4 lines from the console over the logo and than screen turns black until the battery will die.

LENOVO Y2P stuck at Lenovo Splash Screen

I partitioned my SSD into two parts trying to install another OS to the newly unallocated partition. Rebooted into boot menu, but couldn't find my USB drive in the menu. Anyways I said nevermind it's okay and decided to boot normally. It booted without any problem and then for whatever reason I shut down the pc. Turn it back on a little later, now it's stuck at the LENOVO splash screen, won't boot no matter what I do

Do you have a Windows 8 or 7 recovery media? If so, boot to that, enter advance options and do a system restore or boot fix (boot fix is your last option if using a Windows 7 recovery img). This might fix the boot but, the okr system is broken for good unless you purchase recovery disks.

Lenovo G500 stuck at "lenovo splash screen"

Hi
I have Lenovo g500 core i7 ram6 ati radeon 8750 1tb hdd. It's been like a month that laptop freezes at the splash screen. I live in Iran and the laptop is made in China.
I've searched the forums and found the "battery removing, 15sec button-holding and AC Adopter pluging" solution and it worked ...
but today it's not working anymore ... I'm stuck at the splash screen for 4 hours and this is our desktop pc I'm using to post this message.
I really need my laptop! It's my life!
Please help ...

Thanks for reply ...
Your suggested solution does not work
After turning on with "NOVO" button, it stuck at the splash screen ...
I left the laptop to play guitar and after 20 minutes I saw the menu appeared
I went to the BIOS and did the reset. Nothing new happened ...
It still freezes ...
Please help me ... my laptop is my life!
My job, my projects, my researches, everything!

Stuck On Apple Logo (boot menu) HELP!!!!!

Hello, I recently jailbreaked my ipod touch 4g and all i wanted to do was to instal siri. I followed the instructions as they were given but after my device rebooted its stuck on the white apple logo now what can i do? Also I tried to restore it using itunes and i get error "3194" and after getting help from the internet it told me to downoad TINYUMBRELLA somehow, the error 3194 is removed but instead of that another error shows up when it says "veryfying the restore with apple" and that is error "11" please I need help can someone tell me what to do????

Check for hardware issues
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the alert when you update or restore, contact Apple support.
Common errors: 1, 10-47, 1002, 1011, 1012, 1014, 1000-1020.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

K1 stuck in boot loop

My K1 was working great until just recently, now when I turn the power on it is stuck in a startup boot loop. It shows the lenovo logo, then the nvidia logo, then the startup music, and right after that it goes back to the nvidia logo and on and on and on. I have left it in the loop for several hours and not change, it just drains the battery.
I have a lot of videos and pictures on the tablet and they were not backed up (my bad). Is there any way to retrieve the data on the tablet. When I plug my laptop to the tablet via the USB cord, the laptop is not seeing the tablet (for obvious reasons). Has anyone come across this before, is there a way to retrieve the data?

hi Cyclepath,
Sorry to hear about your trouble.
For you to be able to detect the k1 tablet from the laptop, the tablet must first boot into the Android OS. Since the tablet is not doing that, there's no way to backup the data on the tablet unless you send it to a professional recovery company like Drive Savers
What you can try is to:
1. Restore your PC using this method
2. After complete restore, connect your tablet to the PC using the USB cable and check if it's being detected under PC (see this guide)
3. Try to run a data recovery software like EaseUS Data Recovery Wizard.to scan and retrieve the deleted files.
Hope this helps.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Windows 10 Upgrade infinite boot loop after reset

I did a Windows 10 upgrade on an old computer with these specs:-Windows 7 Pro- 64 bit-Dell Optiplex 755-4 GB RAM-Intel Core2 Duo processor Everything ran fine after the upgrade. However I wanted to do a clean install. So I did so and chose the option to not keep any files or programs. It went through the process and was stalled at 99% for some time. I let it run over night. I came back and looked at it about 16 hours later and the 99% was gone, but the "hourglass" was still going. I pressed Escape and then CTRL+ALT+Delete to try to get it to respond. Now it is stuck in an infinite boot loop. It will reboot and then after several minutes it brings up an error message of "Your PC ran into a problem and needs to restart...- Inaccessible boot device." Then it restarts and the loop starts over.I've tried booting into safe mode using F8, but...

These days, there are many ways to combine electronics. Custom gaming PC? No problem. Raspberry Pi arcade? Easy. GoPro on the hood of your RC car? Awesome!I thought up this combo, a tiny portable computer with a huge screenhttp://www.newegg.com/Product/Product.aspx?Item=0FC-001H-00017&cm_re=pico_projector-_-0FC-001H-0...http://www.newegg.com/Product/Product.aspx?Item=N82E16883400001&cm_re=compute_stick-_-83-400-001...What are some of your cool tech combos?

The Phenom K9A2 Platinum Cold Boot Loop with Vista 64-Bit

I've posted about this before and I think others have as well. I will describe it again.
You power up the machine, it POSTS successfully and starts loading Vista 64-Bit. You get the green progress bar and see a bunch of disk activity. The screen flickers for a second as the kernel kicks in. Instead of a pointer you are greeted with "NO SIGNAL" and the machine POSTS again!
I've seen this on 2 different K9A2 Platinum boards with 3 different CPUs: 9500, 9600, and now 9850BE.
I did some debugging last night to isolate it but I don't have a complete answer, I do have some extremely interesting news to report. I have Vista 64-bit on my Promise SAS drives in RAID-0. I have XP 64-bit on an IDE drive on the PATA port. When I experience the "cold boot loop"
as described, I go into the BIOS and switch the primary boot to XP 64-bit. I let the system boot, which is always does successfully. Then I restart the computer and use the BIOS to boot off the Promise RAID. Vista 64-bit always (in 7 out of 7 tries) boots the first time no problems
if I first boot XP 64-bit then try booting Vista. Furthermore if I use a tool like AMD Overdrive to push the CPU, voltage, or memory to a high enough speed to freeze the computer, I can cause the cold boot loop in 7 out of 7 attempts as well. Once the cold boot loop begins, the computer rarely boots (if I leave it for ***HOURS*** sometimes it will boot into Vista, after 100 attempts or something).
I'm not entirely sure what this means. It sounds like there's a sticky bit somewhere, and who knows where, that is causing the issue. I would think not in the CPU itself, although I guess that is possible, when I switched from the 9600 to the 9850BE and powered up, I was stuck in the cold boot loop so I think I can discount the CPU. That really just leaves the BIOS in my opinion. Anybody have any interesting comments
about this?

I experienced similar problems this weekend with my rig.
I have two WD Raptor drives, 150GB on the promise controller and SATA DVD on SB600. If I started Vista, it would boot, show POST screen, then I would see the initial Windows green bar, but after a minute with lots of disk activity then the system would reboot.
Next, I would then be promoted to start windows normally, or start with the last known good configuration, sometimes this worked, sometime it did not. This happended for a while, until I managed to install all of the optional and recommended Vista 64bit OS patches and an updated promise raid driver.
Once these were installed, my system had no boot problems at all, so I would make sure your promise driver is up to date and that all the Vista 64bit OS patches, updates etc are installed.

[LENOVE G460] Stuck at Lenovo Logo Screen when a Boot-able USB plugged in

The subject says it all.
I was thinking of doing a Live Install of a Linux Distribution using a Bootable USB.
So I plugged the Boot-able USB and then Power the Laptopn ON and then press F2 to enter the BIOS SETUP
But even after a few minutes the screen doesn't even budge from the Lenovo Logo... It just says "Entering Setup..."
First I thought something was wrong with my Boot-able USB so I checked it by using another laptop and TADA!!!! I managed to enter the bios setup screen, change the boot order and then start the Linux Installation without any problem.
And then I decided to do it again on the Lenovo G460 and then... The same Stuck at The Lenovo Logo Screen happened again.
Could Anyone shed some light on this problem?
Thanks XD

Hi Warnbroom,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system stuck at Lenovo logo in your Lenovo H500s laptop.
Try to remove the hard drive(HDD) and check for the issue if the system is able to boot to BIOS.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Changes the LCD density on my Lenovo S6000l and now im stuck in a boot loop

I used a program called LCD Density to change my dpi from 160 to 200.
It asked me to reset and i did and now im stuck in a boot loop.
Anything that i can do to fix it.
I did a factory reset but that didnt worl.
Please, i dont know what to do.

I'm sorry this is still happening crimsong19! If you have the Extended Warranty, it's for the life of the phone as long as it's activated on your line. However, if you remove the battery, like you said, it will void the warranty. At this point, you can try reaching out to Motorola to see if they can better assist with this. They may have a good solution. You can reach them at http://www.motorola.com/us/home
Thank you,
VanessaS_VZW
Follow us on Twitter @VZWSupport

Lenovo G45-50 boot loop.

My Lenovo G45-50 has been stuck for days at a time on a boot loop. It starts up, the Lenovo logo comes on the screen, and then reboots again. After about 3 days of this, sometimes it boots up fully. However, as soon as I have to restart (due to updates) or shut down, it will go through this cycle again.
Anyone else have this issue, or know how to have it fixed?

bornxfree wrote:
Thank you CBHendricks,
I did try the reset, but to no avail. Nothing happened. My computer finally turned on this morning, so I tried to contact support, however it is apparently not available in my country yet (Canada). When opened my laptop, there was an alert about "the charger not being able to provide enough power", or something of that nature. I had never seen it before, would the lack of charging capabilities be causing my issue?
Hmm... no support in Canda? That seems rather strange.... It does sound like there is a problem or two with the hardware of your system and it needs to be serviced. Have you spoken to Lenovo support by phone? I would suggest doing so and discuss warranty options, and confirm service center locations. I am certain that I have seen Canada in the list of supported countiries.
Cheers.

Table Yoga 10 stuck at Lenovo logo.

I tried to recover it by pressing the Power+Volume button, it showed a chinese menu which I choose the second option with 2 "M"s it rebooted after like 5 seconds and stuck again in the same Lenovo logo, I'm kind of lost, any help would be appreciated.

Hi Warnbroom,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system stuck at Lenovo logo in your Lenovo H500s laptop.
Try to remove the hard drive(HDD) and check for the issue if the system is able to boot to BIOS.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Lenovo H500s stuck at Lenovo logo boot loop

Similar Messages

Maybe you are looking for