Lenovo Helix i7 CPU cpu clock down after Bios 1.14

Hi all.
I have about 25 Lenovo Helix, and I must admit that I'm a little angry - I have found out that after bios 1.14, then run the only maximum 2.5 GHz, whereas before it ran 3.0GHz - not that I have purchased. It's an easy solution to the heat, just to clock the CPU down.
Is there anyone who can help me, what can I do? Some have bios 1.10 to lie, it works with the real speed. You can easily feel the difference.
Thank you

Use a program like coretemp and after executing the program hit F4 or from the menus select logging. Run some processor intensive applications, either software (AutoCAD, hd video, etc.) or benchmark such as (IBT, Ortho, etc.) then review or post the csv here.
The multiplier is a ratio of the cpu clock rate and front side bus. For instance, with the Helix the fsb is just under/around 100mhz. The clock will either throttle down to 8x and speed up to 32x, resulting in cpu speeds between 800mhz to 3.2Ghz, respectively.
Helix: 3697 CTO.
Thinkpad user since IBM. I do not work for Lenovo or any entity working for Lenovo.

Similar Messages

Helix CPU remains throttled down after redocking

Dear all,
Here is a problem I've just noticed: when I redock the tablet on the keyboard, the CPU will never exceed 30 (occasionally 31%) usage and 0.75 GHz (occasionally 0.78), even under heavy stress (Intel Burn Test at maximum stress level, or CPU-intensive games), and even when temperatures are quite low (65° C) and fan speed far from being maximal (inaudible or just low noise).
I just checked the CPU speed and usage percentage using the Performance tab in the Task manager, so it might be inaccurate, but it is really clear that the CPU is clocked down. See the screenshot below during an Intel Burn test (it's in French, sorry):
Link to picture
I've checked dozens of times: the max CPU speed is set to 100% in the advanced power settings for the power management profile I'm currently using, i.e., High Performance.
If redocking does not revert the CPU to its full capability, then the convertible feature of the Helix is of extremely limited interest. I've realized that because I started to search why my Helix sometimes seemed to show lower performance when executing tasks or running applications, despite free RAM, SSD in good health and with free space, and no processus eating much CPU. In summary, I could feel the différence, and that's how I noticed that it was capped at 30%.
All my drivers and BIOS are up to date. What should I do? Anyone else experiencing this? I'm running the i7 version, quite a disappointment to only benefit 30% of this expensive Helix version...
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

Use a program like coretemp and after executing the program hit F4 or from the menus select logging. Run some processor intensive applications, either software (AutoCAD, hd video, etc.) or benchmark such as (IBT, Ortho, etc.) then review or post the csv here.
The multiplier is a ratio of the cpu clock rate and front side bus. For instance, with the Helix the fsb is just under/around 100mhz. The clock will either throttle down to 8x and speed up to 32x, resulting in cpu speeds between 800mhz to 3.2Ghz, respectively.
Helix: 3697 CTO.
Thinkpad user since IBM. I do not work for Lenovo or any entity working for Lenovo.

K7266 Pro - down after bios update

Hi guys,
i need help.
I flash my bios throught live update to version 1.9. I have winXP.
after few sec i see NT update and after 15 secs computer goes down.
I wait. after 2 mins i turn computer off and boot again. but bios
doesnt working now. I try your procedure for AMI bios with diskette
the problem is that I didnt you A drive before crash co floppy is disabled
in bios now and I cant erase bios config by jumper
What can I do
Thanks for your answers
Tomas

Hi buddy,
the only thing you could do is to bring your machine to an ASP (authorized service partner) for a hardware checkup or BIOS repair because you in your situation cannot do anything.
Please, contact a service partner and send your machine to them, its the only way to solve your problems.
Heres a link to find the nearest ASP in your country:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT
Good luck and nice weekend

Cpu speed is clocked down during heavy use (msi x79a-gd45) ?

Hi
I overclocked my cpu, intel i7 3930K, 32 gb ram win 7 on msi x79a-gd45
cpu base clock : 100
adjust cpu ratio 42
intel turbo disabled
dram freq @1600
cpu core temp 1.290
hyper thread enabled
Everything else is auto
This pc is running at 4.2 in general but when I do render type heavy cpu rendering cpu speed starts going down to 2900, they oscillate betwen 4200 and 2900/2700. I am trying to get it start around 4000. TO me it is kind of pointless that the cpu would clock down when I need them not too. I do not mind if they are clocked down when they are not in use.
I have 750 W with corsair hydro h60
I asked this issue before but I was not able to resolve. I am hoping that someone else might be able to help me out here .
thanks

Quote from: PirateDog on 07-December-13, 17:08:38
Yes, with a Turbo OC on the Core Ratios (set them all to 44X) in CPU Features sub menu plus the CPU V. and CPU Ratio must both be set to Auto. EIST and C1E enabled. Enhanced Turbo enabled. Overspeed Protection disabled.
If the mainboard also has the VDroop option, then set it to 100%. Have you tried the CPU Ratio OC at 44X with the CPU V. in Auto already? If it is stable, then no need to try the Turbo method of OC. With CPU V. in Auto, you can enable EIST and C1E and get power saving features to work. CPU V. must be in Auto for the voltage to decrease at low use or idle (33C).
Hi PirateDog
Thanks for your reply, very helpful
So I now have
Cpu base 100
ratio 44
EIST enabled (intel turbo disabled, enhanced turbo disabled)
Dram auto
Cpu Core V auto
C1E Enabled
C-State disabled
Cpu Phase Control Disabled
VDroop +%100
This setup seemed to push my average cpu temps by around 7C degrees, so I am around 64C if all are at max. I am not sure if this issue is from another place but worth mentioning. I am not sure if this is still in the good range. On the other hand this setup seems to lower my average idle temps couple degrees.
Before I was using
Cpu base 100
ratio 44 Cpu Core V auto
Dram 1600
and everything else was either disabled or set to auto
Any further recommendations?
thanks

MSI Z77 Mpower + 3770K cpu doesn't clock down

Hi MSI Guys, need your help :
my back-up rig is now on duty, but cpu does not clock down, in default cpu speed or overclocked cpu speed
MSI Control Center doesn't shows cpu clock down, core temp 1.0 RC4 either, CPU-Z 1-62.0 x64 the same, only real temp 3.70 does.
In bios every thing regarding cstates and power saving are enabled :
RIG INFO:
CPU: 3770K
MAINB: MSI Z77 MPower
RAM: Corsair Platinum 16GB 2400mhz
VGA: 2XMSI Lightning GTX 680
OS: Windows 7X64 (7601)
PSU: Enermax Revo 85+ 1250W

Quote from: xmad on 14-November-12, 04:27:39
Make sure in advanced, the min max cpu states are what you want them to be and if they are, try the newest beta. Looks like you have H53, it is up to: H57.
Also, after you flashed you bios last, did you re-installed the Intel ME drivers from Intel Downloads?
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22092&keyword=management+engine&lang=eng
Edit: A clearing of the cmos may help as well. >>Clear CMOS Guide<<
i've update the bios as well, and made a correct clear cmos as you linked me to, and even updated those drivers as suggested, and nothing changes
Quote from: Froggy Gremlin on 14-November-12, 04:36:38
Tried with CPU Phase Control 'Enabled'?
yes this too doesnt have any effect
just real temp 3.70 is reading the correct cpu speed, i went on another os installed on my system and no program reads cpu clock down & turbo mode speeds, only Real Temp 3.70 does.
why? what is wrong now?

T43 cpu upgrade shuts down laptop

i have a t43 2668-43u. i tried to install intel m 770 cpu, unit shuts down without warning shortly after booting to windows xp sp3 (i was in the middle of 7 upgrades).
i put the intel m 750 back in and the unit ran fine for 3 days (powered on the whole time).
is there some adjustments i need to make for the 770 to run correctly?
thank you
charlie
Solved!
Go to Solution.

Sounds like a bad CPU to me - 770, that is.
No adjustments of any kind are required, it's a plug & play upgrade.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

694D Dead? Changed CPU Host Clock

Hello all,
This board was running great. I had to do a new OS install and started playing in the BIOS to overclock it. I wanted to change the CPU multiplier but did something with the CPU Host Clock setting. After I changed it the board, just died. It turns on, but the 4 LEDs are RED. I had two PIII 800 w/1GB RAM
I've done the following:
1. Pulled the board and installed one memory stick, one CPU and Video
2. Tried different CPUs (confirmed old CPUs are working fine in a Gigabyte board)
3. Cleared the CMOS by shorting the "Clear CMOS" jumper serveral times.
Any thoughts? I saw this in a earlier post - http://www.flashbios.org/
Thanks!
NB

Sorry I wasn't more complete:
I removed the battery, flipped the Clear CMOS jumper to clear the CMOS and removed all power sources, removed everything (CPU, Cards, etc)
I let it sit for a few days.
I then but the battery back, flipped the jumper so it would boot, added just memory, 1 cpu, and a video card.
Same results.
Thanks for helping out!
NB

Lenovo 3000 N100 laptop shuts down after about 1 minute

Despite being plugged into AC power, my Lenovo 3000 N100 shuts down after about one minute. It boots properly but suddenly shuts down. I have not used this laptop much since purchasing it in 2006 and have seldom used it on battery power alone. Any suggestions before I buy a new battery? Maybe I am mistaken, but shouldn't the computer work on AC despite a depleted battery?

Hi Charleydog and welcome to the community,
Take the battery out and unplug the ac. Hold the power button down for about 15 seconds. Do it twice. Then plug only the ac in and see if it fires up.
Dave
T430u, x301, x200T, x61T, x61, x32, x41T, x40, U160, ThinkPad Tablet 1838-22R, Z500 touch, Yoga Tab 2 Windows 8.1, Yoga Tablet 3 Pro
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
If someone helped you today, pay it forward. Help Someone Else!
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Prime Infrastructure NCS Alarm Message: CPU: 85 crossed down threshold: 90

Dears,
We have Cisco Prime NCS Ver.2.0 running on plad. Since yesterday the alarm give us severity major message (Message: CPU: 85 crossed down threshold: 90).
Please advice what this problem and how to solve it.
Thanks,

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

CPU FSB clock

I don't know much of computers and i have just bought an Athlon XP 2000+ processor. What BIOS settings do i have to change to make it work at the correct operating speed?
I've anyone could help me, i don't wanto fry my PC.
AMD says it's 266 for the CPU FSB clock it this correct?
thanks
Montana

Welcome
It may be set up correctly now. What speed is your chip running now - about 1667 MHZ. How is chip IDed at startup - XP2000+? If not, say you have 2000+ Tbred, set FSB to 133 (266 DDR) and multiplier to 12.5 (think that's correct default). Be sure to give your motherboard manual a good read! Will help with settings.
Depending on your motherboard model, memory, cooling etc, you may (with some experience) be able to run that chip to 166-200 FSB. But don't try above 133 FSB without proper research. You can damage your system. You'll have to furnish your system details to get a better handle on its potential.

Confused about the 'cpu fsb clock frequency' setting, etc., in cell in bios

just got a new k8n neo2-f nforce3 board with an a64 3500+ venice chip. It is properly recognized in the bios and windows as an a64 3500+ at 2.2ghz, but I'm confused about the cell menu settings in the bios. I see a 'cpu fsb clock frequency' which was automatically set at 200mhz, but the fsb runs at 1Ghz (1000mhz), so what is the 'fsb clock frequency' if not equal to the cpu fsb? Is 200 the correct setting for that? Should I need to change any of the other settings in here? I wonder, because my 3dmark03 score only went up 200 points from the same system with a AthlonXP 2500+ chip and kt4avl mobo, which seems like a low increase to me.....

I would set that to Manual in BIOS, so that you can incremently increase the CPU speed without causing a sudden crash. Each system is different and operates within the specs of not only the CPU, but system memory and PCI-E add-ins as well. Your video card is the primary driver behgind your 3DMark scores...but you haven't listed that?!

Setting BIOS CPU FSB clock to 333

Hello everyone,
I recently acquired the K7N2-Delta ILSR (MS-6570) motherboard; nVIDIA Next GF2 400 FSB DDR. The CPU is an Athlon XP 2500 1.85 GHZ, 333 MHz.
The mainboard specs states the Socket A (Socket - 462) supports AMD Athlon XP processors @ FSB 266/333/400. I have the jumper J11 on the board set to 'short'.
With all that said, I've tried adjusting the CPU FSB Clock Frequency to 333 in the BIOS Setup Utility yet 200 is the highest option it gives. Does the CPU Interface have to be set to 'High Performance'? Other adjustments necessary?
Thanks for any feedback!

200 mhz fsb is the correct setting, DDR is just that "double data rate" so 200 x 2 = 400 mhz
MikeB

Cpu fsb clock setting?

I bought a Microstar MS-6380E KT3 Ultra with an AMD Athlon XP 1800+ (1.53Ghz) 266FSB CPU -- it just got in today.
I have it all set up EXCEPT for the clock frequency. The 6380 has a default of 100mhz, up to 220. But the AMD Athlon XP 1800+ is supposed to be a 266 fsb.
I don't want to overclock my system -- am afraid to endanger my system when I really don't need the extra processing power. I just want it set the way it should be.
There's another field -- CPU Ratio/Vcore (V), w/ the following manual description for it:
The items are used to adjust the CPU clock multiplier (artion) and CPU core voltage (Vcore). The fields provide users a tool to overclock the system. WARNING: Changing CPU Ratio/Vcore could result in the instability of the system; therefore, it is NOT recommended to change the default setting for long-term usage.
I was gonna _guess_ that I set my CPU FSB Clock to 133 and input a CPU clock multiplier (ratio) of 2 (assuming I could do that). Is that the correct way to configure this AMD Athlon 1800+ to this motherboard? The 'CPU core voltage (Vcore)' descriptor is what is making me afraid of experimenting. I would really hate myself if I destroyed my new cpu and/or motherboard less than 6 hours of having received it.
Please advise.

I doubt you can set the clock multiplier to "2" - simply it isn't available. Even if it is available and u hv not unlock your CPU, adjusting the multiplier ratio has no effect at all.
The default multiplier for 1800+ is 11.5x. Multiply it by 133fsb you get 1529.50mhz, hence xp1800+ (1.53G).
Don't confuse yourself, juz follow this setting if u r not overclocking:
FSB Clock: 133
CPU Ratio: AUTO
CPU VCORE: AUTO

KT4AV MSI-6712 Dead after BIOS Flash to support XP3000 CPU (Photos)

Hello, I'm a 15-year veteran system administrator and hardware hacker and this is the first time I have ever had what appears to be a truly DEAD mobo killed after a BIOS flash!
Of course I read all the stickies and spent 2 hours research & homework first, before posting here. I tried everything to revive this mobo.
Here's what happened:
MSI-6712 KT4AV system with onboard Audio and Ethernet, Athlon 2800+ CPU, 1GB (2 x 512MB PC2700 DDR) RAM. 300W PSU. It's been running great for years with never an issue. I just got a Athlon 3000+ CPU I wanted to upgrade, but before I did I decided I had better upgrade the BIOS to support this newer CPU, since the BIOS Version History says the later revisions handle the 3000 CPU.
I upgraded the BIOS from DOS Boot via a Bootable USB and it Verified successfully. Then I rebooted and it said something like Invalid CMOS settings, so I entered BIOS Setup to view my new BIOS. I noticed new features like Network Boot ability, so the new BIOS seemed to be a success. (Note this was a soft-reboot, not a hard power-off reboot). I set my normal settings and saved to reboot and the system was DEAD from that point on! No beeps, monitor stays black. CPU fan does run but that's it.
Here is what I have:
(This image is larger if you view it directly)
Things I have tried:
Removing all RAM and vacuuming dust, reseating 1 stick nearest the CPU. (This shouldnt be necessary since I have not removed the ram or disturbed it, but I tried anyway since D-Bracket LED indicates a Memory error.)
Trying a different brand PC2700 DDR RAM stick.
Removing CMOS battery for 10 minutes.
Jumpering Clear CMOS a dozen times. Leaving Clear CMOS jumper overnight (desperate!).
Disconnected all devices from mobo, all HDs, even the AGP video card.
Unfortunately, since the mobo fails so early, it never beeps or initializes the keyboard, so safe-mode INS or CTRL-HOME don't work... so I can't reload my old BIOS backup I carefully saved before I flashed the new one.
As you can see the BIOS chip is soldered directly to the mobo.... so am I 100% dead here? Is there anything I can do?
I am 100% positive I did this BIOS update correctly and there is no reason it should have killed the mobo!

Quote
UPDATE: Oh boy, it looks like I may have flashed the WRONG BIOS???!?!
Too possible, that's why i ask
Quote
I'm not sure what my old bios version was, I couldn't find any way to tell? The BIOS flash utility did not display my old version anywhere either.
Well you told that you have created BIOS backup before update the BIOS, ==> "so I can't reload my old BIOS backup I carefully saved before I flashed the new one."
Can you upload it somewhere to check it?
Quote
I now see that I should have instead flashed BIOS v5.4 for KT4AV: http://www.msi.com/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=552
I am shocked at this mistake... Can such a small discrepency (KT4V-L vs KT4AV) really kill my motherboard? I saw the KT4V-L and thought it was right because my mobo has Onboard LAN...
I'm doomed!
Quote
Can such a small discrepency (KT4V-L vs KT4AV) really kill my motherboard?
Sure yes, will be no wonder

Disp+work process was down after the Restoreing the backup

Disp+work process is down after the Restore of the backup
s/m configration: windows 2003 server + oracle 10g
The below is the log file
trc file: "dev_disp", trc level: 1, release: "700"
sysno      01
sid        PRA
systemid   560 (PC with Windows NT)
relno      7000
patchlevel 0
patchno    52
intno      20050900
make:      multithreaded, Unicode, optimized
pid        2928
Thu Apr 07 18:58:10 2011
kernel runs with dp version 210000(ext=109000) (@(#) DPLIB-INT-VERSION-210000-UC)
length of sys_adm_ext is 572 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (01 2928) [dpxxdisp.c   1231]
     shared lib "dw_xml.dll" version 52 successfully loaded
     shared lib "dw_xtc.dll" version 52 successfully loaded
     shared lib "dw_stl.dll" version 52 successfully loaded
     shared lib "dw_gui.dll" version 52 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3901
Thu Apr 07 18:58:15 2011
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 5 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5233]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >pwsap_PRA_01                            <
DpShMCreate: sizeof(wp_adm)          18304     (1408)
DpShMCreate: sizeof(tm_adm)          3954072     (19672)
DpShMCreate: sizeof(wp_ca_adm)          24000     (80)
DpShMCreate: sizeof(appc_ca_adm)     8000     (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm)          528064     (1048)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm)          0     (72)
DpShMCreate: sizeof(vmc_adm)          0     (1452)
DpShMCreate: sizeof(wall_adm)          (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm)     48
DpShMCreate: SHM_DP_ADM_KEY          (addr: 05C00040, size: 4613144)
DpShMCreate: allocated sys_adm at 05C00040
DpShMCreate: allocated wp_adm at 05C01E28
DpShMCreate: allocated tm_adm_list at 05C065A8
DpShMCreate: allocated tm_adm at 05C065D8
DpShMCreate: allocated wp_ca_adm at 05FCBB70
DpShMCreate: allocated appc_ca_adm at 05FD1930
DpShMCreate: allocated comm_adm at 05FD3870
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 06054730
DpShMCreate: allocated gw_adm at 06054770
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 060547A0
DpShMCreate: allocated wall_adm at 060547A8
MBUF state OFF
EmInit: MmSetImplementation( 2 ).
MM diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation flat
<EsNT> Memory Reset disabled as NT default
<ES> 511 blocks reserved for free list.
ES initialized.
Thu Apr 07 18:58:16 2011
J2EE server info
start = TRUE
state = STARTED
pid = 3208
argv[0] = D:\usr\sap\PRA\DVEBMGS01\exe\jcontrol.EXE
argv[1] = D:\usr\sap\PRA\DVEBMGS01\exe\jcontrol.EXE
argv[2] = pf=D:\usr\sap\PRA\SYS\profile\PRA_DVEBMGS01_pwsap
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=1069
argv[5] = -DSAPSYSTEM=01
argv[6] = -DSAPSYSTEMNAME=PRA
argv[7] = -DSAPMYNAME=pwsap_PRA_01
argv[8] = -DSAPPROFILE=D:\usr\sap\PRA\SYS\profile\PRA_DVEBMGS01_pwsap
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c   1617]
***LOG Q0K=> DpMsAttach, mscon ( pwsap) [dpxxdisp.c   11414]
DpStartStopMsg: send start message (myname is >pwsap_PRA_01                            <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
Thu Apr 07 18:58:17 2011
CCMS: start to initalize 3.X shared alert area (first segment).
DpJ2eeLogin: j2ee state = CONNECTED
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c   1050]
DpMsgAdmin: Set patchno for this platform to 52
Release check o.K.
Thu Apr 07 18:58:42 2011
***LOG Q0I=> NiIRead: recv (10054: WSAECONNRESET: Connection reset by peer) [nixxi.cpp 4235]
ERROR => NiIRead: SiRecv failed for hdl 4 / sock 1472
     (SI_ECONN_BROKEN; I4; ST; 127.0.0.1:1085) [nixxi.cpp    4235]
DpJ2eeMsgProcess: j2ee state = CONNECTED (NIECONN_BROKEN)
DpIJ2eeShutdown: send SIGINT to SAP J2EE startup framework (pid=3208)
ERROR => DpProcKill: kill failed [dpntdisp.c   371]
DpIJ2eeShutdown: j2ee state = SHUTDOWN
Thu Apr 07 18:58:56 2011
ERROR => W0 (pid 3216) died [dpxxdisp.c   14021]
ERROR => W1 (pid 3224) died [dpxxdisp.c   14021]
ERROR => W2 (pid 3232) died [dpxxdisp.c   14021]
ERROR => W3 (pid 3240) died [dpxxdisp.c   14021]
ERROR => W4 (pid 3248) died [dpxxdisp.c   14021]
ERROR => W5 (pid 3256) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xbf --> 0xbe
ERROR => W6 (pid 3264) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xbe --> 0xbc
ERROR => W7 (pid 3272) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xbc --> 0xb8
ERROR => W8 (pid 3280) died [dpxxdisp.c   14021]
ERROR => W9 (pid 3288) died [dpxxdisp.c   14021]
ERROR => W10 (pid 3296) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xb8 --> 0xb0
ERROR => W11 (pid 3304) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xb0 --> 0xa0
ERROR => W12 (pid 3312) died [dpxxdisp.c   14021]
my types changed after wp death/restart 0xa0 --> 0x80
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=1597
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Thu Apr 07 18:59:06 2011
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long)               Fri Apr 08 01:59:06 2011
========================
No Ty. Pid      Status Cause Start Err Sem CPU    Time Program Cl User         Action                    Table
0 DIA     3216 Ended         no      1   0             0
1 DIA     3224 Ended         no      1   0             0
2 DIA     3232 Ended         no      1   0             0
3 DIA     3240 Ended         no      1   0             0
4 DIA     3248 Ended         no      1   0             0
5 DIA     3256 Ended         no      1   0             0
6 UPD     3264 Ended         no      1   0             0
7 ENQ     3272 Ended         no      1   0             0
8 BTC     3280 Ended         no      1   0             0
9 BTC     3288 Ended         no      1   0             0
10 BTC     3296 Ended         no      1   0             0
11 SPO     3304 Ended         no      1   0             0
12 UP2     3312 Ended         no      1   0             0
Dispatcher Queue Statistics               Fri Apr 08 01:59:06 2011
===========================
--------++++--
+
Typ
now
high
max
writes
reads
--------++++--
+
NOWP
0
2
2000
5
5
--------++++--
+
DIA
5
5
2000
5
0
--------++++--
+
UPD
0
0
2000
0
0
--------++++--
+
ENQ
0
0
2000
0
0
--------++++--
+
BTC
0
0
2000
0
0
--------++++--
+
SPO
0
0
2000
0
0
--------++++--
+
UP2
0
0
2000
0
0
--------++++--
+
max_rq_id          12
wake_evt_udp_now     0
wake events           total     8, udp     6 ( 75%), shm     2 ( 25%)
since last update     total     8, udp     6 ( 75%), shm     2 ( 25%)
Dump of tm_adm structure:               Fri Apr 08 01:59:06 2011
=========================
Term    uid man user    term   lastop mod wp ta   a/i (modes)
Workprocess Comm. Area Blocks               Fri Apr 08 01:59:06 2011
=============================
Slots: 300, Used: 1, Max: 0
--------++--
+
id
owner
pid
eyecatcher
--------++--
+
0
DISPATCHER
-1
WPCAAD000
NiWait: sleep (5000ms) ...
NiISelect: timeout 5000ms
NiISelect: maximum fd=1597
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Thu Apr 07 18:59:11 2011
NiISelect: TIMEOUT occured (5000ms)
DpHalt: shutdown server >pwsap_PRA_01                            < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_PREPARED

trc file: "dev_w0", trc level: 1, release: "700"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      all, MJ
B
B Thu Apr 07 18:58:16 2011
B create_con (con_name=R/3)
B Loading DB library 'D:\usr\sap\PRA\DVEBMGS01\exe\dboraslib.dll' ...
B Library 'D:\usr\sap\PRA\DVEBMGS01\exe\dboraslib.dll' loaded
B Version of 'D:\usr\sap\PRA\DVEBMGS01\exe\dboraslib.dll' is "700.08", patchlevel (0.46)
B New connection 0 created
M sysno      01
M sid        PRA
M systemid   560 (PC with Windows NT)
M relno      7000
M patchlevel 0
M patchno    52
M intno      20050900
M make:      multithreaded, Unicode, optimized
M pid        3216
M
M kernel runs with dp version 210000(ext=109000) (@(#) DPLIB-INT-VERSION-210000-UC)
M length of sys_adm_ext is 572 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 3216) [dpxxdisp.c   1293]
I MtxInit: 30000 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
M DpShMCreate: sizeof(wp_adm)          18304     (1408)
M DpShMCreate: sizeof(tm_adm)          3954072     (19672)
M DpShMCreate: sizeof(wp_ca_adm)          24000     (80)
M DpShMCreate: sizeof(appc_ca_adm)     8000     (80)
M DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
M DpShMCreate: sizeof(comm_adm)          528064     (1048)
M DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
M DpShMCreate: sizeof(file_adm)          0     (72)
M DpShMCreate: sizeof(vmc_adm)          0     (1452)
M DpShMCreate: sizeof(wall_adm)          (38456/34360/64/184)
M DpShMCreate: sizeof(gw_adm)     48
M DpShMCreate: SHM_DP_ADM_KEY          (addr: 05C00040, size: 4613144)
M DpShMCreate: allocated sys_adm at 05C00040
M DpShMCreate: allocated wp_adm at 05C01E28
M DpShMCreate: allocated tm_adm_list at 05C065A8
M DpShMCreate: allocated tm_adm at 05C065D8
M DpShMCreate: allocated wp_ca_adm at 05FCBB70
M DpShMCreate: allocated appc_ca_adm at 05FD1930
M DpShMCreate: allocated comm_adm at 05FD3870
M DpShMCreate: system runs without file table
M DpShMCreate: allocated vmc_adm_list at 06054730
M DpShMCreate: allocated gw_adm at 06054770
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 060547A0
M DpShMCreate: allocated wall_adm at 060547A8
X EmInit: MmSetImplementation( 2 ).
X MM diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation flat
M <EsNT> Memory Reset disabled as NT default
X ES initialized.
M
M Thu Apr 07 18:58:17 2011
M ThInit: running on host pwsap
M
M Thu Apr 07 18:58:18 2011
M calling db_connect ...
C Prepending D:\usr\sap\PRA\DVEBMGS01\exe to Path.
C
C Thu Apr 07 18:58:27 2011
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPSR3's password
C Connecting as /@PRA on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet                 NationalCharSet              C      EnvHp      ErrHp ErrHpBatch
C    0 UTF8                                                      1   0619F158   061A46F4   061A3F7C
C Attaching to DB Server PRA (con_hdl=0,svchp=061A3EC8,svrhp=061B5794)
C Starting user session (con_hdl=0,svchp=061A3EC8,srvhp=061B5794,usrhp=061CA558)
C
C Thu Apr 07 18:58:28 2011
C *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1033
[dboci.c      4345]
C Detaching from DB Server (con_hdl=0,svchp=061A3EC8,srvhp=061B5794)
C *** ERROR => CONNECT failed with sql error '1033'
[dbsloci.c    10704]
C Try to connect with default password
C Connecting as SAPSR3/<pwd>@PRA on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet                 NationalCharSet              C      EnvHp      ErrHp ErrHpBatch
C    0 UTF8                                                      1   0619F158   061A46F4   061A3F7C
C Attaching to DB Server PRA (con_hdl=0,svchp=061A3EC8,svrhp=061B5794)
C Starting user session (con_hdl=0,svchp=061A3EC8,srvhp=061B5794,usrhp=061CA558)
C *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1033
[dboci.c      4345]
C Detaching from DB Server (con_hdl=0,svchp=061A3EC8,srvhp=061B5794)
C *** ERROR => CONNECT failed with sql error '1033'
[dbsloci.c    10704]
B ***LOG BV3=> severe db error 1033      ; work process is stopped [dbsh#2 @ 1199] [dbsh    1199 ]
B ***LOG BY2=> sql error 1033   performing CON [dblink#3 @ 431] [dblink 0431 ]
B ***LOG BY0=> ORA-01033: ORACLE initialization or shutdown in progress [dblink#3 @ 431] [dblink 0431 ]
M ***LOG R19=> ThInit, db_connect ( DB-Connect 000256) [thxxhead.c   1403]
M in_ThErrHandle: 1
M *** ERROR => ThInit: db_connect (step 1, th_errno 13, action 3, level 1) [thxxhead.c   10019]
M
M Info for wp 0
M
M    stat = 4
M    reqtype = 1
M    act_reqtype = -1
M    rq_info = 0
M    tid = -1
M    mode = 255
M    len = -1
M    rq_id = 65535
M    rq_source = 255
M    last_tid = 0
M    last_mode = 0
M    semaphore = 0
M    act_cs_count = 0
M    control_flag = 0
M    int_checked_resource(RFC) = 0
M    ext_checked_resource(RFC) = 0
M    int_checked_resource(HTTP) = 0
M    ext_checked_resource(HTTP) = 0
M    report = >                                        <
M    action = 0
M    tab_name = >                              <
M    vm = V-1
M
M *
M * LOCATION    SAP-Server pwsap_PRA_01 on host pwsap (wp 0)
M * ERROR       ThInit: db_connect
M *
M * TIME        Thu Apr 07 18:58:28 2011
M * RELEASE     700
M * COMPONENT   Taskhandler
M * VERSION     1
M * RC          13
M * MODULE      thxxhead.c
M * LINE        10204
M * COUNTER     1
M *
M
M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c   720]
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c 260]
M Entering ThSetStatError
M ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
M Entering ThReadDetachMode
M call ThrShutDown (1)...
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 3216) [dpnttool.c   327]

Lenovo Helix i7 CPU cpu clock down after Bios 1.14

Similar Messages

Maybe you are looking for