Lenovo ideapad u510 w/Fedora 19 Live USB black screen
I am having difficulty with a new lenovo ideapad u510. I am attempting to install Fedora 19 using the Fedora 19 xfce spin Live USB image, and the drive boots properly, but upon selecting the option to start Fedora 19 Live, I get a gray screen with a cursor on the top left, then two error messages that look almost idential to each other flash by, the Fedora logo starts to load, and then the screen goes blank.
The part of the error message that I was able to make out was "...failed to enable the AA(?????)"
I have attempted to turn the monitor back on using the F9 key's alternate function, and I have tried booting from DVD with the same result. Once the screen goes blank, it stays that way until I force the machine to shut down. Once I've forced the shutdown, the computer, upon turning back on, goes to the blank screen again without even loading the lenovo BIOS screen. Even the 'novo' button will not load any options for me.
My UEFI is set to Legacy / Legacy First, although the EFI setting is still Windows 8, with no alternate options. I've looked all through my settings in every tab of the BIOS and I can't find anything further to disable secure boot.
Is anybody able to assist me in installing Fedora?
Solved!
Go to Solution.
Follow up:
I have tried more flavors of linux, and over the course of doing that, I have discovered that after choosing to boot a linux live disk, the screen does not instantly go black as I had thought with the Fedora installation, but rather is reduced to 1/4 the physical size of the screen for a few seconds, then goes blank. After it goes blank, apparently, the live OS continues to load, as evidenced by the loading .wav sounds that play even after the screen is blank.
More and more I'm convinced that the graphics hardware is causing problems, but the lenovo site is completely silent about the specifics of the graphics, saying only that the hardware is nvidia GeForce series.
Similar Messages
-
Al cerrar la tapa, se abre el chasis Lenovo Ideapad u510
Saludos: No tenía idea de como llamar a mi problema, así que no se me ocurrió un mejor título. Mi Lenovo Ideapad U510 ya tiene más o menos un año conmigo. Pero hace unos días me percaté que al cerrar la tapa, el plástico del chasis parece como si quisiera abrirse, supongo, que por problemas en la visagra. Para que se entienda mejor les dejo un video. https://youtu.be/K0JeMUjyGRQ Quisiera añadir que donde vivo actualmente no hay ningún centro de Soporte de Lenovo o fabricante alguno de ordenadores. Es por ello que necesito consejos para solucionar esto tratando de arreglarlo por mi cuenta.
Hola elav que tal,
Has destapado para observar el panorama?.
Eh visto casos mas drásticos y resulta que este desprendimiento es originado por el tornillo que ajusta la bisagra hacia la parte inferior del ordenador.
Te recomiendo seguir el manual de mantenimiento https://download.lenovo.com/consumer/mobiles_pub/ideapad_u510_hmm_1st_edition_sep_2012_english.pdf para el destape del ordenador y verificar el estado en que se encuentra lo de las bisagras. y el tornillo, antes de proceder a hacer cualquier otra cosa.
La recomendación principal es si no se tienes las herramientas y el conocimiento adecuado lo mejor es llevarlo a un servicio técnico, por solucionar un problema se puede ocasionar otro mas.
Un saludo. -
Lenovo IdeaPad U510 touchpad scrolling with 2 fingers
Hello. I bought a lenovo ideapad u 510 yesterday and I think I have a problem. whenever i try scrolling with 2 fingers i have to press harder than when i am simply just moving the pointer with 1 finger. is this normal? on my old laptop i didn't had to press harder with 2 fingers, but here if i don't the touchpad thinks i am using just one.
paulalex93 wrote:
http://www.synaptics.com/en/drivers.php this is the site where i downloaded the latest drivers
This is your second post : "PS: i donwloaded the latest drivers from elan website and I also edited the sensitivity to light touch which is maximum."
So which touchpad do you really have? Elan or Synaptic? -
Lenovo Ideapad U410 scrolling down with a grey screen
HI,
I just recently purchased the Lenovo Ideapad U410 and sometimes when I try to scroll down with both fingers, a grey line and background bar starts to come down and encompass the whole screen, rendering the screen and all my apps useless. And then on the right side, it shows the time and date squished togetherand I can't seem to get out of it unless I go back to the start and then open the desktop again.
Why is it doing this and is there a way to stop it because when it scrolls all the way down, the laptop won't work and if I don't touch the touchpad, bubbles start forming forming as if it's a screen saver.
ThanksIt sounds like your hard drive is failing or has failed. It cannot repair the disk and is suggesting you back up and format the drive. Do you already have a backup?
A couple of things to try first:
NVRAM reset: http://support.apple.com/kb/HT1379
SMC reset: http://support.apple.com/kb/ht3964 -
I have bought a lenovo ideapad u510 a week before. From the very begining I am facing toucpad problem, The cursor jumps everywhere in the screen and make automatic selection all by itself. I am totally unable to control the cursor.
I have tried installing Synaptics driver after unistalling default Elan driver, but it wasn't solved a bit. I have tried by changing various options from the Elan menu, also disabled 'Multi-finger' option.
I have bought it from Canada but now I'm far away from there. So if anyone knows the solution please help me.Please reinstall your default touchpad driver (ELAN). According to Elan: The main cause of unexpected cursor moving or click is the accidental palm contact with the touch pad. You can adjust your Palm Tracking setting to maximum to make your touch pad insensitive to "palm contacts"
-
hey guys i have been using fedoras live usb installs on my 2 gig usb stick for a while now and would like to try arch on a usb, i will be putting barebone kdemod on there along with wireless apps for managing and connecting to wireless networks, my question is are there any tutorials, is it the same as a normal install but with no swap, and a different filesystem? and lastly will 2 gb be enough for bade arch, kde mod + apps such as web browsers, im, email, gimp and possible a few little games?
Cew27;
Faunos utilizes USB flash devices to install an archlinux-based system and which utilizes a program called ...mkxorgconfig....which examines the computer system being addressed to modify xorg.conf to enable the system to reach DE in KDE. This program is placed in /etc/rc.local and can be commented out after the xorg.conf is established for a given computer.
You may surmise correctly that this method doesn't fit every case due to third party driver problems.... -
Display replacement for Ideapad u510
Hello,
I want to replace the display of my Lenovo Ideapad U510 with a matte one. The FRU No. of the Display ist 18200449 or 18200450. But on this site I only find 18200442 and 18200453. Can I use these displays too?
And another question: the u510 looks very similar to the u400. Can I use this tutorial?
GreetzHi Phoenix53,
Welcome to Lenovo Community Forums!
Looking at this Maintenance Manual of this System.
Lenovo B460 Hardware Maintenance Manual V2.0
Youll find the replacement screen for your system at Page 76 of 88
Checking the part numbers with online resellers will give you options on where to purchase them.
Hope this helps,
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
Ideapad U510 Battery Stuck at 94%
Hi,
I bought a brand new Lenovo Ideapad U510 just yesterday, but when I charge it, it does not charge past 94%. The status remains at 94% plugged in and charging, but it doesn't actually change even after an hour or two.
I have tried unplugging to 10% and then recharging but again it got stuck at 94%. And yes I have checked the energy mangement and it is on Maximum Battery Life.
Should I drain the battery completely and then try recharging?
Is there a way to fix it to charge all the way to 100% or is it a problem with the computer itself? Thank you.Drain the battery first and then try again. Probably this is also maybe happening to prevent battery detoriation. So this can be normal.
Jonas
Microsoft MVP: Windows Consumer Expert
Yoga Tablet 2 10 || ThinkPad X1 Carbon (20A7007MPH) || ThinkPad Helix (3698-6EU) || IdeaCentre B540
Twitter: @jonashendrickx -
Lenovo Ideapad u400 6470M driver problems Windows 7 Home Premium 64bit HELP
I bought this lenovo u400 like 2 years ago and i had no problems, but now my SSD went dead and i bought another, after the replacement i just installed the original windows 7 64 bit home premium, put my notebook's serial installed all the drivers, and when i install the Ati driver from Lenovo my pc gets stuck in a black screen with a white line on the top left of my screen, when i do FN+F8 while booting and start window's safe mode and i go to the device manager i see this ones: 6470M and Intel HD graphics family, when i disable intel hd graphics family my pc boots up normally but the resolution is 800x600 and the max is 1024x768, If i install the Intel 3000 HD my 6470m appears with a yellow triangle on the device manager, i've tried almost 30 different drivers from leshcat, hp, dell, lenovo and AMD's webpage, none of them work, and when i go to the CCC it just lists the intel 3000.
Sorry for my bad english, im from Argentina, Lenovo's support on argentina sucks, last time i've sent it it costed a lot of money, they scratched multiple parts on my laptop and didn't fix most of my problems, and i can't get the One Key backup anywhere, pls help, atleast AND IF ANYONE WITH A LENOVO U400 WITH WINDOWS 7 HOME PREMIUM IS READING THIS AND HIS 6470M DRIVER IS WORKING, PLEASE CONTACT ME.
Lenovo, please, don't give me a crappy answer and most of times when that answer does not fix the problem then you give up and don't reply anymore. Im getting sick, i got this laptop for doing 3D modeling, video editing and multiple more and i just can't go and buy another, things are really expensive in Argentina.welcome to the community.
i would recommend that you call Service to request a factory recovery dvd set.
phone #s here: http://support.lenovo.com/en_US/detail.page?DocID=PD008370
for Slovokia, specifically: +421 2 4974 8888 for Think-branded machines and 0800-197-462 for Idea-branded machines.
hope this helps a bit.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee. -
Lenovo Ideapad U410 - no screen output or black screen, and just out of warranty
My kid has been using this laptop and loved it, but mentioned a while ago it was difficult to power it back on after turnned it off. However she managed to work around by putting it in hibernate/sleeping mode only, or recycling the system many times (by holding on power button to force it off). The issue was black screen (no Lenovo logo) but computer was on. I didn't pay much attention because she can still make it work, and I was too busy. Last week, there was a windows update (again) and the computer was forced recycle. It never comes back alive again. The same, computer is humming, but no any visual output on screen, just black. Tried novo button, bootable USB, external monitor, all no use. Check the warranty, just over by 2 months! Asked the service store, to fix will cost at least $200-$300 to replace the motherboard! It does not make sense when spent a bit more could buy a new notebook. But my kid liked it and it does not make sense to throw it away either, when it still looks pretty new and only being used very lightly (schoolwork only). It is sad, especially the brand has been gainning my trust. I probably don't expect a "good" solution either from Lenovo or community, but just throw my frustration here (only because have just registered the account and there is no support email or web form). If Lenovo want to make customer happy, the part shouldn't be so expensive for a short-lived laptop! Just by the way, there are many posts about Ideapad's black screen issue, and many blameed window 8.1 for the compatibility problem. It made me thought so too because the initial sympton was exactly the same. The best thing you should do: don't waste time on fixing the driver or config, get the hardware replaced as soon as you could when still in warranty. If not so lucky, probably think it twice next time when you want to buy a Lenovo.
Welcome to the Lenovo Community !
Sorry to hear of all the problems. Here are a couple of things to try........
First, try a reset of the BIOS. The procedure can be useful in resolving some hardware conflicts which your computer may have. Just do this......
1. Unplug the charger / adapter.
2. Press and hold the Power Button for 15 seconds.
3. Plug in the charger / adapter if needed and power up the system to see if the problem was resolved.
If you are comfortable working inside your laptop. try this........
Try the reset again with the battery removed.
If the reset didn't resolve the problem then you may have a failed piece of hardware preventing the bootup. Remove the battery, hard drive, optical drive, memory, wireless card and bluetooth if it is installed. Now try to power up the stripped laptop. With all the hardware removed you should have lights come on and it may possibly beep since there is no memory installed. If the laptop is showing signs of life start adding hardware one piece at a time starting with a memory module and boot up the laptop. If it doesn't power up try the memory in the other slot. Also try the other memory module separately in both slots if two are available. If it is still showing signs of life add another piece and boot. Do this for each item until it doesn't power up again. The last piece of hardware installed is your problem part.
The link below is for your model's Hardware Maintenance Manual. The manual will explain how to remove the various hardware items. When working inside your system please follow all precautions and recommendations that are noted in the manual.
http://download.lenovo.com/consumer/mobiles_pub/ideapad_u310_u410_hmm_1st_edition_mar_2012_english.pdf
There is also a Lenovo Training video that will show you how to remove the various items. These are listed in the FRU section.
http://service.lenovo.partner-management.com/content/CourseWarePublic/12769/player.html -
Lenovo ideapad s410p screen keeps black out,and started twitching
I have just bought a new lenovo ideapad s410p a month ago. The problem started when i inserted an external hard disk into the laptop and opened the photo gallery. The screen will suddenly blackout and srarted twitching.i on and off, and tried all other posible ways but the problem repeared. Once i on, it will totally blackout and have to wait quie long for it to load. Even i on, the screen also twitch. I dont know what is the problem and i have sent to the shop whwre i bought it and they couldnt find the problem.after a few days the same problem occured again.what is happening??
Heloo,
Don' turn off the Fish Pump!
~BDAqua
http://www.yelp.com/biz/b-and-d-aquarium-seattle
Ray C was a bit out of touch & was speaking of a place a half mile away that supports "Growers" for Hydroponic stuff... LOL
Anyway...
Get Temperature Monitor to see if it's heat related...
http://www.macupdate.com/info.php/id/12381/temperature-monitor
iStat Menus...
http://bjango.com/mac/istatmenus/
And/or iStat Pro...
http://www.islayer.com/apps/istatpro/ -
[concluded] Enabling SLI (Lenovo Ideapad y500 / dual gt 650m)
final edit:
Apparently there is no support for sli on mobile nvidia gpu. Thank you ever so much Nvidia, you willf orever hold a special place in my heart..
I've miracously gotten everything else to work. Only thing left is enabling sli, which I haven't been able to.
As far as I know, I've follow the instruction to the letter, but all I get i a black screen and a log with no particular useful information that I can find:
[ 13.106]
X.Org X Server 1.15.1
Release Date: 2014-04-13
[ 13.106] X Protocol Version 11, Revision 0
[ 13.106] Build Operating System: Linux 3.14.0-4-ARCH x86_64
[ 13.106] Current Operating System: Linux zarchbook 3.14.4-1-ARCH #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014 x86_64
[ 13.106] Kernel command line: initrd=\initramfs-linux.img root=/dev/sda2 rw quiet nomodeset rcutree.rcu_idle_gp_delay=1 loglevel=3
[ 13.106] Build Date: 14 April 2014 08:39:09AM
[ 13.106]
[ 13.106] Current version of pixman: 0.32.4
[ 13.106] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 13.106] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 13.107] (==) Log file: "/var/log/Xorg.0.log", Time: Sat May 31 17:50:00 2014
[ 13.108] (==) Using config file: "/etc/X11/xorg.conf"
[ 13.108] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 13.109] (==) ServerLayout "Layout0"
[ 13.109] (**) |-->Screen "Screen0" (0)
[ 13.109] (**) | |-->Monitor "Monitor0"
[ 13.110] (**) | |-->Device "Device0"
[ 13.110] (**) |-->Input Device "Keyboard0"
[ 13.110] (**) |-->Input Device "Mouse0"
[ 13.110] (**) Option "BlankTime" "0"
[ 13.110] (==) Automatically adding devices
[ 13.110] (==) Automatically enabling devices
[ 13.110] (==) Automatically adding GPU devices
[ 13.112] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 13.112] Entry deleted from font path.
[ 13.113] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 13.113] Entry deleted from font path.
[ 13.113] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 13.114] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 13.114] Entry deleted from font path.
[ 13.114] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 13.114] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 13.114] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 13.114] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 13.114] (WW) Disabling Keyboard0
[ 13.114] (WW) Disabling Mouse0
[ 13.114] (II) Loader magic: 0x804c80
[ 13.114] (II) Module ABI versions:
[ 13.114] X.Org ANSI C Emulation: 0.4
[ 13.114] X.Org Video Driver: 15.0
[ 13.114] X.Org XInput driver : 20.0
[ 13.114] X.Org Server Extension : 8.0
[ 13.114] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 13.114] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 13.117] (--) PCI:*(0:1:0:0) 10de:0fd1:17aa:3972 rev 161, Mem @ 0xb3000000/16777216, 0xa0000000/268435456, 0xb0000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
[ 13.117] (--) PCI: (0:2:0:0) 10de:0fd1:17aa:3972 rev 161, Mem @ 0xb2000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00003000/128
[ 13.117] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 13.117] Initializing built-in extension Generic Event Extension
[ 13.117] Initializing built-in extension SHAPE
[ 13.117] Initializing built-in extension MIT-SHM
[ 13.117] Initializing built-in extension XInputExtension
[ 13.117] Initializing built-in extension XTEST
[ 13.117] Initializing built-in extension BIG-REQUESTS
[ 13.117] Initializing built-in extension SYNC
[ 13.117] Initializing built-in extension XKEYBOARD
[ 13.118] Initializing built-in extension XC-MISC
[ 13.118] Initializing built-in extension SECURITY
[ 13.118] Initializing built-in extension XINERAMA
[ 13.118] Initializing built-in extension XFIXES
[ 13.118] Initializing built-in extension RENDER
[ 13.118] Initializing built-in extension RANDR
[ 13.118] Initializing built-in extension COMPOSITE
[ 13.118] Initializing built-in extension DAMAGE
[ 13.118] Initializing built-in extension MIT-SCREEN-SAVER
[ 13.118] Initializing built-in extension DOUBLE-BUFFER
[ 13.118] Initializing built-in extension RECORD
[ 13.118] Initializing built-in extension DPMS
[ 13.118] Initializing built-in extension Present
[ 13.118] Initializing built-in extension DRI3
[ 13.118] Initializing built-in extension X-Resource
[ 13.118] Initializing built-in extension XVideo
[ 13.118] Initializing built-in extension XVideo-MotionCompensation
[ 13.118] Initializing built-in extension XFree86-VidModeExtension
[ 13.118] Initializing built-in extension XFree86-DGA
[ 13.119] Initializing built-in extension XFree86-DRI
[ 13.119] Initializing built-in extension DRI2
[ 13.119] (II) LoadModule: "glx"
[ 13.121] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 13.212] (II) Module glx: vendor="NVIDIA Corporation"
[ 13.212] compiled for 4.0.2, module version = 1.0.0
[ 13.212] Module class: X.Org Server Extension
[ 13.212] (II) NVIDIA GLX Module 337.19 Tue Apr 29 19:48:33 PDT 2014
[ 13.212] Loading extension GLX
[ 13.212] (II) LoadModule: "nvidia"
[ 13.212] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 13.219] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 13.219] compiled for 4.0.2, module version = 1.0.0
[ 13.219] Module class: X.Org Video Driver
[ 13.220] (II) NVIDIA dlloader X Driver 337.19 Tue Apr 29 19:22:36 PDT 2014
[ 13.220] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 13.220] (++) using VT number 1
[ 13.221] (II) Loading sub module "fb"
[ 13.221] (II) LoadModule: "fb"
[ 13.221] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 13.222] (II) Module fb: vendor="X.Org Foundation"
[ 13.222] compiled for 1.15.1, module version = 1.0.0
[ 13.222] ABI class: X.Org ANSI C Emulation, version 0.4
[ 13.222] (WW) Unresolved symbol: fbGetGCPrivateKey
[ 13.222] (II) Loading sub module "wfb"
[ 13.222] (II) LoadModule: "wfb"
[ 13.222] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 13.223] (II) Module wfb: vendor="X.Org Foundation"
[ 13.223] compiled for 1.15.1, module version = 1.0.0
[ 13.223] ABI class: X.Org ANSI C Emulation, version 0.4
[ 13.223] (II) Loading sub module "ramdac"
[ 13.224] (II) LoadModule: "ramdac"
[ 13.224] (II) Module "ramdac" already built-in
[ 13.237] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[ 13.237] (==) NVIDIA(0): RGB weight 888
[ 13.237] (==) NVIDIA(0): Default visual is TrueColor
[ 13.237] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 13.238] (**) NVIDIA(0): Option "NoLogo" "True"
[ 13.238] (**) NVIDIA(0): Option "SLI" "Auto"
[ 13.238] (**) NVIDIA(0): Option "ModeValidation" "AllowNonEdidModes"
[ 13.238] (**) NVIDIA(0): NVIDIA SLI auto-select rendering option.
[ 13.238] (**) NVIDIA(0): Option "UseEDID" "FALSE"
[ 13.238] (**) NVIDIA(0): Option "MetaModes" "1920x1080_60 +0+0 { ForceFullCompositionPipeline = On }"
[ 13.238] (**) NVIDIA(0): Enabling 2D acceleration
[ 13.238] (**) NVIDIA(0): Ignoring EDIDs
[ 17.131] (WW) NVIDIA(GPU-0): Failed to initialize the SLI configuration for the NVIDIA
[ 17.131] (WW) NVIDIA(GPU-0): graphics device PCI:1:0:0. Please see Chapter 29:
[ 17.131] (WW) NVIDIA(GPU-0): Configuring SLI and Multi-GPU FrameRendering in the README
[ 17.131] (WW) NVIDIA(GPU-0): for troubleshooting suggestions.
In the end, all that I can learn from this is that stuff don't work, not why or how to fix it. A bit annoying to be blunt.
I've been googling around for answers, but the closest thing I've come to an answer, and I do hope it isn't true, is that sli om mobile nvidia gpu is not supported under linux. I've been unable to confirm this.
I do hope you can help.
Best regards.
edit:
Just for kicks, here's my xorg.conf:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 337.19 (buildmeister@swio-display-x64-rhel04-03) Tue Apr 29 20:34:50 PDT 2014
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "BlankTime" "0"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 66.5 - 66.5
VertRefresh 59.9
ModeLine "1920x1080" 138.500 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync
Option "DPMS"
EndSection
Section "Device"
BusID "PCI:1:0:0"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "metamodes" "1920x1080_60 +0+0 { ForceFullCompositionPipeline = On }"
Option "NoLogo" "True"
Option "ModeValidation" "AllowNonEdidModes"
Option "UseEDID" "FALSE"
Option "SLI" "Auto"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Ya, it's a mess, but nothing particular wrong with is that I can see.
edit2:
Just in case some information is lagging, here is the nvidia compiled bug report in it's entirety:
Start of NVIDIA bug report log file. Please include this file, along
with a detailed description of your problem, when reporting a graphics
driver bug via the NVIDIA Linux forum (see devtalk.nvidia.com)
or by sending email to '[email protected]'.
nvidia-bug-report.sh Version: 17818519
Date: lør maj 31 21:11:50 CEST 2014
uname: Linux zarchbook 3.14.4-1-ARCH #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014 x86_64 GNU/Linux
command line flags:
*** /etc/issue
*** ls: -rw-r--r-- 1 root root 20 2013-05-31 20:40:23.000000000 +0200 /etc/issue
Arch Linux \r (\l)
*** /var/log/nvidia-installer.log does not exist
*** /var/log/Xorg.0.log
*** ls: -rw-r--r-- 1 root zacariaz 7488 2014-05-31 21:10:38.492892729 +0200 /var/log/Xorg.0.log
[ 11.874]
X.Org X Server 1.15.1
Release Date: 2014-04-13
[ 11.874] X Protocol Version 11, Revision 0
[ 11.874] Build Operating System: Linux 3.14.0-4-ARCH x86_64
[ 11.875] Current Operating System: Linux zarchbook 3.14.4-1-ARCH #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014 x86_64
[ 11.875] Kernel command line: initrd=\initramfs-linux.img root=/dev/sda2 rw quiet nomodeset rcutree.rcu_idle_gp_delay=1 loglevel=3
[ 11.875] Build Date: 14 April 2014 08:39:09AM
[ 11.875]
[ 11.875] Current version of pixman: 0.32.4
[ 11.875] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 11.875] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 11.875] (==) Log file: "/var/log/Xorg.0.log", Time: Sat May 31 21:10:34 2014
[ 11.877] (==) Using config file: "/etc/X11/xorg.conf"
[ 11.877] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 11.878] (==) ServerLayout "Layout0"
[ 11.878] (**) |-->Screen "Screen0" (0)
[ 11.878] (**) | |-->Monitor "Monitor0"
[ 11.878] (**) | |-->Device "Device0"
[ 11.878] (**) |-->Input Device "Keyboard0"
[ 11.878] (**) |-->Input Device "Mouse0"
[ 11.878] (**) Option "BlankTime" "0"
[ 11.878] (==) Automatically adding devices
[ 11.878] (==) Automatically enabling devices
[ 11.878] (==) Automatically adding GPU devices
[ 11.881] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 11.881] Entry deleted from font path.
[ 11.882] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 11.882] Entry deleted from font path.
[ 11.882] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 11.882] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 11.882] Entry deleted from font path.
[ 11.882] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 11.882] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 11.882] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 11.882] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 11.882] (WW) Disabling Keyboard0
[ 11.882] (WW) Disabling Mouse0
[ 11.882] (II) Loader magic: 0x804c80
[ 11.882] (II) Module ABI versions:
[ 11.882] X.Org ANSI C Emulation: 0.4
[ 11.882] X.Org Video Driver: 15.0
[ 11.882] X.Org XInput driver : 20.0
[ 11.882] X.Org Server Extension : 8.0
[ 11.883] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 11.883] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 11.885] (--) PCI:*(0:1:0:0) 10de:0fd1:17aa:3972 rev 161, Mem @ 0xb3000000/16777216, 0xa0000000/268435456, 0xb0000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
[ 11.885] (--) PCI: (0:2:0:0) 10de:0fd1:17aa:3972 rev 161, Mem @ 0xb2000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00003000/128
[ 11.885] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 11.886] Initializing built-in extension Generic Event Extension
[ 11.886] Initializing built-in extension SHAPE
[ 11.886] Initializing built-in extension MIT-SHM
[ 11.886] Initializing built-in extension XInputExtension
[ 11.886] Initializing built-in extension XTEST
[ 11.886] Initializing built-in extension BIG-REQUESTS
[ 11.886] Initializing built-in extension SYNC
[ 11.886] Initializing built-in extension XKEYBOARD
[ 11.886] Initializing built-in extension XC-MISC
[ 11.886] Initializing built-in extension SECURITY
[ 11.886] Initializing built-in extension XINERAMA
[ 11.886] Initializing built-in extension XFIXES
[ 11.886] Initializing built-in extension RENDER
[ 11.886] Initializing built-in extension RANDR
[ 11.886] Initializing built-in extension COMPOSITE
[ 11.886] Initializing built-in extension DAMAGE
[ 11.886] Initializing built-in extension MIT-SCREEN-SAVER
[ 11.886] Initializing built-in extension DOUBLE-BUFFER
[ 11.887] Initializing built-in extension RECORD
[ 11.887] Initializing built-in extension DPMS
[ 11.887] Initializing built-in extension Present
[ 11.887] Initializing built-in extension DRI3
[ 11.887] Initializing built-in extension X-Resource
[ 11.887] Initializing built-in extension XVideo
[ 11.887] Initializing built-in extension XVideo-MotionCompensation
[ 11.887] Initializing built-in extension XFree86-VidModeExtension
[ 11.887] Initializing built-in extension XFree86-DGA
[ 11.887] Initializing built-in extension XFree86-DRI
[ 11.887] Initializing built-in extension DRI2
[ 11.887] (II) LoadModule: "glx"
[ 11.889] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 11.978] (II) Module glx: vendor="NVIDIA Corporation"
[ 11.978] compiled for 4.0.2, module version = 1.0.0
[ 11.978] Module class: X.Org Server Extension
[ 11.978] (II) NVIDIA GLX Module 337.19 Tue Apr 29 19:48:33 PDT 2014
[ 11.979] Loading extension GLX
[ 11.979] (II) LoadModule: "nvidia"
[ 11.979] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 11.986] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 11.986] compiled for 4.0.2, module version = 1.0.0
[ 11.986] Module class: X.Org Video Driver
[ 11.986] (II) NVIDIA dlloader X Driver 337.19 Tue Apr 29 19:22:36 PDT 2014
[ 11.986] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 11.987] (++) using VT number 1
[ 11.988] (II) Loading sub module "fb"
[ 11.988] (II) LoadModule: "fb"
[ 11.988] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 11.989] (II) Module fb: vendor="X.Org Foundation"
[ 11.989] compiled for 1.15.1, module version = 1.0.0
[ 11.989] ABI class: X.Org ANSI C Emulation, version 0.4
[ 11.989] (WW) Unresolved symbol: fbGetGCPrivateKey
[ 11.989] (II) Loading sub module "wfb"
[ 11.989] (II) LoadModule: "wfb"
[ 11.989] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 11.990] (II) Module wfb: vendor="X.Org Foundation"
[ 11.990] compiled for 1.15.1, module version = 1.0.0
[ 11.990] ABI class: X.Org ANSI C Emulation, version 0.4
[ 11.990] (II) Loading sub module "ramdac"
[ 11.990] (II) LoadModule: "ramdac"
[ 11.990] (II) Module "ramdac" already built-in
[ 12.004] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[ 12.004] (==) NVIDIA(0): RGB weight 888
[ 12.004] (==) NVIDIA(0): Default visual is TrueColor
[ 12.004] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 12.004] (**) NVIDIA(0): Option "NoLogo" "True"
[ 12.004] (**) NVIDIA(0): Option "SLI" "Auto"
[ 12.004] (**) NVIDIA(0): Option "ModeValidation" "AllowNonEdidModes"
[ 12.004] (**) NVIDIA(0): NVIDIA SLI auto-select rendering option.
[ 12.004] (**) NVIDIA(0): Option "UseEDID" "FALSE"
[ 12.004] (**) NVIDIA(0): Option "MetaModes" "1920x1080_60 +0+0 { ForceFullCompositionPipeline = On }"
[ 12.004] (**) NVIDIA(0): Enabling 2D acceleration
[ 12.004] (**) NVIDIA(0): Ignoring EDIDs
[ 15.847] (WW) NVIDIA(GPU-0): Failed to initialize the SLI configuration for the NVIDIA
[ 15.847] (WW) NVIDIA(GPU-0): graphics device PCI:1:0:0. Please see Chapter 29:
[ 15.847] (WW) NVIDIA(GPU-0): Configuring SLI and Multi-GPU FrameRendering in the README
[ 15.847] (WW) NVIDIA(GPU-0): for troubleshooting suggestions.
*** /etc/X11/xorg.conf
*** ls: -rw-r--r-- 1 root root 1733 2014-05-31 21:10:12.876322985 +0200 /etc/X11/xorg.conf
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 337.19 (buildmeister@swio-display-x64-rhel04-03) Tue Apr 29 20:34:50 PDT 2014
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "BlankTime" "0"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 66.5 - 66.5
VertRefresh 59.9
ModeLine "1920x1080" 138.500 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync
Option "DPMS"
EndSection
Section "Device"
BusID "PCI:1:0:0"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "metamodes" "1920x1080_60 +0+0 { ForceFullCompositionPipeline = On }"
Option "NoLogo" "True"
Option "ModeValidation" "AllowNonEdidModes"
Option "UseEDID" "FALSE"
Option "SLI" "Auto"
SubSection "Display"
Depth 24
EndSubSection
EndSection
*** /etc/X11/xorg.conf.d/10-evdev.conf
*** ls: -rw-r--r-- 1 root root 1099 2014-04-14 10:40:04.000000000 +0200 /etc/X11/xorg.conf.d/10-evdev.conf
# Catch-all evdev loader for udev-based systems
# We don't simply match on any device since that also adds accelerometers
# and other devices that we don't really want to use. The list below
# matches everything but joysticks.
Section "InputClass"
Identifier "evdev pointer catchall"
MatchIsPointer "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev keyboard catchall"
MatchIsKeyboard "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchpad catchall"
MatchIsTouchpad "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev tablet catchall"
MatchIsTablet "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
Section "InputClass"
Identifier "evdev touchscreen catchall"
MatchIsTouchscreen "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
EndSection
*** /etc/X11/xorg.conf.d/10-keyboard.conf
*** ls: -rw-r--r-- 1 root root 201 2014-05-07 20:02:13.920335503 +0200 /etc/X11/xorg.conf.d/10-keyboard.conf
Section "InputClass"
Identifier "system-keyboard"
MatchIsKeyboard "on"
Option "XkbLayout" "dk"
Option "XkbModel" "pc104"
Option "XkbVariant" "qwerty"
EndSection
*** /etc/X11/xorg.conf.d/10-quirks.conf
*** ls: -rw-r--r-- 1 root root 377 2014-04-14 10:40:06.000000000 +0200 /etc/X11/xorg.conf.d/10-quirks.conf
# Collection of quirks and blacklist/whitelists for specific devices.
# Accelerometer device, posts data through ABS_X/ABS_Y, making X unusable
# http://bugs.freedesktop.org/show_bug.cgi?id=22442
Section "InputClass"
Identifier "ThinkPad HDAPS accelerometer blacklist"
MatchProduct "ThinkPad HDAPS accelerometer data"
Option "Ignore" "on"
EndSection
*** /home/zacariaz/.nvidia-settings-rc
*** ls: -rw-r--r-- 1 zacariaz users 1982 2014-05-31 20:34:36.266975242 +0200 /home/zacariaz/.nvidia-settings-rc
# /home/zacariaz/.nvidia-settings-rc
# Configuration file for nvidia-settings - the NVIDIA X Server Settings utility
# Generated on Sat May 31 20:34:36 2014
# ConfigProperties:
RcFileLocale = C
ToolTips = Yes
DisplayStatusBar = Yes
SliderTextEntries = Yes
IncludeDisplayNameInConfigFile = No
ShowQuitDialog = Yes
UpdateRulesOnProfileNameChange = Yes
Timer = PowerMizer_Monitor_(GPU_1),Yes,1000
Timer = Thermal_Monitor_(GPU_1),Yes,1000
Timer = Memory_Used_(GPU_1),Yes,3000
Timer = Memory_Used_(GPU_0),Yes,3000
Timer = Thermal_Monitor_(GPU_0),Yes,1000
Timer = PowerMizer_Monitor_(GPU_0),Yes,1000
# Attributes:
0/SyncToVBlank=1
0/LogAniso=0
0/FSAA=0
0/TextureSharpen=0
0/TextureClamping=1
0/FXAA=0
0/AllowFlipping=1
0/FSAAAppControlled=1
0/LogAnisoAppControlled=1
0/OpenGLImageSettings=3
0/FSAAAppEnhanced=0
0/XVideoSyncToDisplayID=VGA-0
[DPY:VGA-0]/Dithering=0
[DPY:VGA-0]/DitheringMode=0
[DPY:VGA-0]/DitheringDepth=0
[DPY:VGA-0]/SynchronousPaletteUpdates=0
[DPY:LVDS-0]/Dithering=0
[DPY:LVDS-0]/DitheringMode=0
[DPY:LVDS-0]/DitheringDepth=0
[DPY:LVDS-0]/SynchronousPaletteUpdates=0
[DPY:HDMI-0]/Dithering=0
[DPY:HDMI-0]/DitheringMode=0
[DPY:HDMI-0]/DitheringDepth=0
[DPY:HDMI-0]/SynchronousPaletteUpdates=0
[DPY:VGA-0]/Dithering=0
[DPY:VGA-0]/DitheringMode=0
[DPY:VGA-0]/DitheringDepth=0
[DPY:VGA-0]/SynchronousPaletteUpdates=0
[DPY:LVDS-0]/RedBrightness=0.000000
[DPY:LVDS-0]/GreenBrightness=0.000000
[DPY:LVDS-0]/BlueBrightness=0.000000
[DPY:LVDS-0]/RedContrast=0.000000
[DPY:LVDS-0]/GreenContrast=0.000000
[DPY:LVDS-0]/BlueContrast=0.000000
[DPY:LVDS-0]/RedGamma=1.000000
[DPY:LVDS-0]/GreenGamma=1.000000
[DPY:LVDS-0]/BlueGamma=1.000000
[DPY:LVDS-0]/Dithering=0
[DPY:LVDS-0]/DitheringMode=0
[DPY:LVDS-0]/DitheringDepth=0
[DPY:LVDS-0]/DigitalVibrance=0
[DPY:LVDS-0]/ColorSpace=0
[DPY:LVDS-0]/ColorRange=0
[DPY:LVDS-0]/SynchronousPaletteUpdates=0
[DPY:HDMI-0]/Dithering=0
[DPY:HDMI-0]/DitheringMode=0
[DPY:HDMI-0]/DitheringDepth=0
[DPY:HDMI-0]/SynchronousPaletteUpdates=0
*** /usr/share/nvidia/nvidia-application-profiles-337.19-rc
*** ls: -rw-r--r-- 1 root root 2310 2014-05-20 14:28:33.000000000 +0200 /usr/share/nvidia/nvidia-application-profiles-337.19-rc
# Application profiles for the NVIDIA Linux graphics driver, version 337.19
# Last modified: Tue Apr 29 19:51:54 PDT 2014
# These profiles were provided by NVIDIA and should not be modified. If you
# wish to change the defaults provided here, you can override them by creating
# custom rules in /etc/nvidia/nvidia-application-profiles-rc (which will apply
# system-wide) or, for a given user, $HOME/.nv/nvidia-application-profiles-rc
# (which will apply to that particular user). See the "APPLICATION PROFILE
# SEARCH PATH" section of the NVIDIA Linux Graphics Driver README for more
# information.
"profiles" : [
"name" : "NonConformantBlitFramebufferScissor",
"settings" : [ "GLConformantBlitFramebufferScissor", false ]
"name" : "CL1C",
"settings" : [ "0x528ab3", 1 ]
"name" : "FA0",
"settings" : [ "10572898", 0 ]
"name" : "ExactGLESVersion",
"settings" : [ "ForceRequestedESVersion", 1 ]
"name" : "BGTE",
"settings" : [ "GLAppReturnOnlyBasicGlslType", 1 ]
"rules" : [
# Work around GNOME bug 690451 (see
# https://bugzilla.gnome.org/show_bug.cgi?id=690451)
"pattern" : {
"feature" : "dso",
"matches" : "libcogl.so"
"profile" : "NonConformantBlitFramebufferScissor"
{ "pattern" : "Maya2014", "profile" : "CL1C" },
{ "pattern" : "xsi", "profile" : "CL1C" },
{ "pattern" : "HoudiniFX", "profile" : "CL1C" },
{ "pattern" : "katana", "profile" : "CL1C" },
{ "pattern" : "Autodesk Mudbox 2014 64-bit", "profile" : "CL1C" },
{ "pattern" : "octane", "profile" : "CL1C" },
{ "pattern" : "Fusion64_6.4", "profile" : "CL1C" },
{ "pattern" : "Nuke7.0", "profile" : "CL1C" },
{ "pattern" : "vray.exe", "profile" : "CL1C" },
{ "pattern" : "vray.bin", "profile" : "CL1C" },
{ "pattern" : "kwin_gles", "profile" : "FA0" },
{ "pattern" : "kwin_gles", "profile" : "ExactGLESVersion" },
{ "pattern" : "heaven_x86", "profile" : "BGTE" },
{ "pattern" : "heaven_x64", "profile" : "BGTE" }
Skipping ldd output (glxinfo not found)
/sbin/lspci -d "10de:*" -v -xxx
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 650M] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 3972
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at b3000000 (32-bit, non-prefetchable) [size=16M]
Memory at a0000000 (64-bit, prefetchable) [size=256M]
Memory at b0000000 (64-bit, prefetchable) [size=32M]
I/O ports at 4000 [size=128]
Expansion ROM at b4080000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900] #19
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia
00: de 10 d1 0f 07 00 10 00 a1 00 00 03 10 00 80 00
10: 00 00 00 b3 0c 00 00 a0 00 00 00 00 0c 00 00 b0
20: 00 00 00 00 01 40 00 00 00 00 00 00 aa 17 72 39
30: 00 00 f8 ff 60 00 00 00 00 00 00 00 00 01 00 00
40: aa 17 72 39 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00
60: 01 68 03 00 08 00 00 00 05 78 80 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 10 b4 02 00 e1 8d 2c 01
80: 30 29 00 00 03 3d 45 00 43 00 81 10 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 13 00 00 00
a0: 00 00 00 00 0e 00 00 00 03 00 01 00 00 00 00 00
b0: 00 00 00 00 09 00 14 01 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.1 Audio device: NVIDIA Corporation GK107 HDMI Audio Controller (rev a1)
Subsystem: Lenovo Device 3977
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at b4000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00: de 10 1b 0e 06 00 10 00 a1 00 03 04 10 00 80 00
10: 00 00 00 b4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 aa 17 77 39
30: 00 00 00 00 60 00 00 00 00 00 00 00 00 02 00 00
40: aa 17 77 39 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 ce d6 23 00 00 00 00 00
60: 01 68 03 00 08 00 00 00 05 78 80 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 10 00 02 00 e1 8d 2c 01
80: 30 29 00 00 03 3d 45 00 43 00 81 10 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 13 00 00 00
a0: 00 00 00 00 0e 00 00 00 00 00 01 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
02:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 650M] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 3972
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at b2000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at d0000000 (64-bit, prefetchable) [size=32M]
I/O ports at 3000 [size=128]
Expansion ROM at <ignored> [disabled]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900] #19
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia
00: de 10 d1 0f 07 00 10 00 a1 00 00 03 10 00 00 00
10: 00 00 00 b2 0c 00 00 c0 00 00 00 00 0c 00 00 d0
20: 00 00 00 00 01 30 00 00 00 00 00 00 aa 17 72 39
30: 00 00 f8 ff 60 00 00 00 00 00 00 00 00 01 00 00
40: aa 17 72 39 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00
60: 01 68 03 00 08 00 00 00 05 78 80 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 10 b4 02 00 e1 8d 2c 01
80: 10 29 00 00 03 3d 45 01 43 00 82 10 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 13 00 00 00
a0: 00 00 00 00 0e 00 00 00 03 00 01 00 00 00 00 00
b0: 00 00 00 00 09 00 14 01 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
/sbin/lspci -d "10b5:*" -v -xxx
/sbin/lspci -t
-[0000:00]-+-00.0
+-01.0-[01]--+-00.0
| \-00.1
+-01.1-[02]----00.0
+-14.0
+-16.0
+-1a.0
+-1b.0
+-1c.0-[03]----00.0
+-1c.1-[04]----00.0
+-1c.3-[05]--+-00.0
| +-00.2
| +-00.3
| \-00.4
+-1d.0
+-1f.0
+-1f.2
\-1f.3
/sbin/lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09)
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09)
00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0155] (rev 09)
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04)
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04)
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4)
00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4)
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 [8086:1e16] (rev c4)
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04)
00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04)
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04)
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GK107M [GeForce GT 650M] [10de:0fd1] (rev a1)
01:00.1 Audio device [0403]: NVIDIA Corporation GK107 HDMI Audio Controller [10de:0e1b] (rev a1)
02:00.0 VGA compatible controller [0300]: NVIDIA Corporation GK107M [GeForce GT 650M] [10de:0fd1] (rev a1)
03:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8161 Gigabit Ethernet [1969:1091] (rev 10)
04:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 2230 [8086:0888] (rev c4)
05:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2392] (rev 30)
05:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2391] (rev 30)
05:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2393] (rev 30)
05:00.4 System peripheral [0880]: JMicron Technology Corp. xD Host Controller [197b:2394] (rev 30)
/sbin/lsusb
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 8087:07da Intel Corp.
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 04f2:b331 Chicony Electronics Co., Ltd
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Skipping dmidecode output (dmidecode not found)
/sbin/modinfo nvidia | grep vermagic
vermagic: 3.14.4-1-ARCH SMP preempt mod_unload modversions
Scanning kernel log files for NVRM messages:
/var/log/messages is not readable
/var/log/kernel.log is not readable
dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14.4-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.0 20140507 (prerelease) (GCC) ) #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014
[ 0.000000] Command line: initrd=\initramfs-linux.img root=/dev/sda2 rw quiet nomodeset rcutree.rcu_idle_gp_delay=1 loglevel=3
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000087fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000995affff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000995b0000-0x000000009a9affff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009a9b0000-0x000000009efbefff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009efbf000-0x000000009f6befff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009f6bf000-0x000000009f7befff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f7bf000-0x000000009f7fefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000009f7ff000-0x000000009f7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009f800000-0x000000009fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000045effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] e820: update [mem 0x985ad018-0x985d3057] usable ==> usable
[ 0.000000] e820: update [mem 0x98586018-0x985ac057] usable ==> usable
[ 0.000000] e820: update [mem 0x98579018-0x98585057] usable ==> usable
[ 0.000000] extended physical RAM map:
[ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x0000000000087fff] usable
[ 0.000000] reserve setup_data: [mem 0x0000000000088000-0x00000000000bffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000098579017] usable
[ 0.000000] reserve setup_data: [mem 0x0000000098579018-0x0000000098585057] usable
[ 0.000000] reserve setup_data: [mem 0x0000000098585058-0x0000000098586017] usable
[ 0.000000] reserve setup_data: [mem 0x0000000098586018-0x00000000985ac057] usable
[ 0.000000] reserve setup_data: [mem 0x00000000985ac058-0x00000000985ad017] usable
[ 0.000000] reserve setup_data: [mem 0x00000000985ad018-0x00000000985d3057] usable
[ 0.000000] reserve setup_data: [mem 0x00000000985d3058-0x00000000995affff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000995b0000-0x000000009a9affff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000009a9b0000-0x000000009efbefff] usable
[ 0.000000] reserve setup_data: [mem 0x000000009efbf000-0x000000009f6befff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000009f6bf000-0x000000009f7befff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x000000009f7bf000-0x000000009f7fefff] ACPI data
[ 0.000000] reserve setup_data: [mem 0x000000009f7ff000-0x000000009f7fffff] usable
[ 0.000000] reserve setup_data: [mem 0x000000009f800000-0x000000009fffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000045effffff] usable
[ 0.000000] efi: EFI v2.31 by INSYDE Corp.
[ 0.000000] efi: ACPI=0x9f7fe000 ACPI 2.0=0x9f7fe014 SMBIOS=0x9f6bef98
[ 0.000000] efi: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
[ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000001000-0x0000000000007000) (0MB)
[ 0.000000] efi: mem02: type=7, attr=0xf, range=[0x0000000000007000-0x000000000006f000) (0MB)
[ 0.000000] efi: mem03: type=4, attr=0xf, range=[0x000000000006f000-0x0000000000070000) (0MB)
[ 0.000000] efi: mem04: type=7, attr=0xf, range=[0x0000000000070000-0x0000000000080000) (0MB)
[ 0.000000] efi: mem05: type=3, attr=0xf, range=[0x0000000000080000-0x0000000000082000) (0MB)
[ 0.000000] efi: mem06: type=7, attr=0xf, range=[0x0000000000082000-0x0000000000088000) (0MB)
[ 0.000000] efi: mem07: type=6, attr=0x800000000000000f, range=[0x0000000000088000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem08: type=7, attr=0xf, range=[0x0000000000100000-0x0000000001000000) (15MB)
[ 0.000000] efi: mem09: type=2, attr=0xf, range=[0x0000000001000000-0x0000000001f5b000) (15MB)
[ 0.000000] efi: mem10: type=7, attr=0xf, range=[0x0000000001f5b000-0x000000007f857000) (2008MB)
[ 0.000000] efi: mem11: type=2, attr=0xf, range=[0x000000007f857000-0x0000000080000000) (7MB)
[ 0.000000] efi: mem12: type=7, attr=0xf, range=[0x0000000080000000-0x00000000979c0000) (377MB)
[ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x00000000979c0000-0x00000000979e0000) (0MB)
[ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x00000000979e0000-0x0000000097e62000) (4MB)
[ 0.000000] efi: mem15: type=1, attr=0xf, range=[0x0000000097e62000-0x000000009821b000) (3MB)
[ 0.000000] efi: mem16: type=7, attr=0xf, range=[0x000000009821b000-0x0000000098579000) (3MB)
[ 0.000000] efi: mem17: type=2, attr=0xf, range=[0x0000000098579000-0x00000000985d4000) (0MB)
[ 0.000000] efi: mem18: type=4, attr=0xf, range=[0x00000000985d4000-0x00000000995b0000) (15MB)
[ 0.000000] efi: mem19: type=0, attr=0xf, range=[0x00000000995b0000-0x000000009a9b0000) (20MB)
[ 0.000000] efi: mem20: type=7, attr=0xf, range=[0x000000009a9b0000-0x000000009a9b8000) (0MB)
[ 0.000000] efi: mem21: type=2, attr=0xf, range=[0x000000009a9b8000-0x000000009a9bb000) (0MB)
[ 0.000000] efi: mem22: type=7, attr=0xf, range=[0x000000009a9bb000-0x000000009a9bc000) (0MB)
[ 0.000000] efi: mem23: type=2, attr=0xf, range=[0x000000009a9bc000-0x000000009a9bd000) (0MB)
[ 0.000000] efi: mem24: type=7, attr=0xf, range=[0x000000009a9bd000-0x000000009a9be000) (0MB)
[ 0.000000] efi: mem25: type=2, attr=0xf, range=[0x000000009a9be000-0x000000009a9bf000) (0MB)
[ 0.000000] efi: mem26: type=7, attr=0xf, range=[0x000000009a9bf000-0x000000009aba8000) (1MB)
[ 0.000000] efi: mem27: type=1, attr=0xf, range=[0x000000009aba8000-0x000000009abbf000) (0MB)
[ 0.000000] efi: mem28: type=7, attr=0xf, range=[0x000000009abbf000-0x000000009af27000) (3MB)
[ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x000000009af27000-0x000000009b063000) (1MB)
[ 0.000000] efi: mem30: type=7, attr=0xf, range=[0x000000009b063000-0x000000009b064000) (0MB)
[ 0.000000] efi: mem31: type=4, attr=0xf, range=[0x000000009b064000-0x000000009c9f3000) (25MB)
[ 0.000000] efi: mem32: type=7, attr=0xf, range=[0x000000009c9f3000-0x000000009c9fb000) (0MB)
[ 0.000000] efi: mem33: type=4, attr=0xf, range=[0x000000009c9fb000-0x000000009ca11000) (0MB)
[ 0.000000] efi: mem34: type=7, attr=0xf, range=[0x000000009ca11000-0x000000009ca12000) (0MB)
[ 0.000000] efi: mem35: type=4, attr=0xf, range=[0x000000009ca12000-0x000000009ca1d000) (0MB)
[ 0.000000] efi: mem36: type=7, attr=0xf, range=[0x000000009ca1d000-0x000000009ca1f000) (0MB)
[ 0.000000] efi: mem37: type=4, attr=0xf, range=[0x000000009ca1f000-0x000000009ca21000) (0MB)
[ 0.000000] efi: mem38: type=7, attr=0xf, range=[0x000000009ca21000-0x000000009ca22000) (0MB)
[ 0.000000] efi: mem39: type=4, attr=0xf, range=[0x000000009ca22000-0x000000009ca45000) (0MB)
[ 0.000000] efi: mem40: type=7, attr=0xf, range=[0x000000009ca45000-0x000000009ca47000) (0MB)
[ 0.000000] efi: mem41: type=4, attr=0xf, range=[0x000000009ca47000-0x000000009cd81000) (3MB)
[ 0.000000] efi: mem42: type=7, attr=0xf, range=[0x000000009cd81000-0x000000009cd82000) (0MB)
[ 0.000000] efi: mem43: type=4, attr=0xf, range=[0x000000009cd82000-0x000000009cfa7000) (2MB)
[ 0.000000] efi: mem44: type=7, attr=0xf, range=[0x000000009cfa7000-0x000000009cfa8000) (0MB)
[ 0.000000] efi: mem45: type=4, attr=0xf, range=[0x000000009cfa8000-0x000000009cfbf000) (0MB)
[ 0.000000] efi: mem46: type=7, attr=0xf, range=[0x000000009cfbf000-0x000000009cfc5000) (0MB)
[ 0.000000] efi: mem47: type=4, attr=0xf, range=[0x000000009cfc5000-0x000000009cfd0000) (0MB)
[ 0.000000] efi: mem48: type=7, attr=0xf, range=[0x000000009cfd0000-0x000000009cfd2000) (0MB)
[ 0.000000] efi: mem49: type=4, attr=0xf, range=[0x000000009cfd2000-0x000000009cfe9000) (0MB)
[ 0.000000] efi: mem50: type=7, attr=0xf, range=[0x000000009cfe9000-0x000000009cfea000) (0MB)
[ 0.000000] efi: mem51: type=4, attr=0xf, range=[0x000000009cfea000-0x000000009ebbf000) (27MB)
[ 0.000000] efi: mem52: type=7, attr=0xf, range=[0x000000009ebbf000-0x000000009ec3a000) (0MB)
[ 0.000000] efi: mem53: type=3, attr=0xf, range=[0x000000009ec3a000-0x000000009efbf000) (3MB)
[ 0.000000] efi: mem54: type=5, attr=0x800000000000000f, range=[0x000000009efbf000-0x000000009f04e000) (0MB)
[ 0.000000] efi: mem55: type=6, attr=0x800000000000000f, range=[0x000000009f04e000-0x000000009f050000) (0MB)
[ 0.000000] efi: mem56: type=5, attr=0x800000000000000f, range=[0x000000009f050000-0x000000009f066000) (0MB)
[ 0.000000] efi: mem57: type=6, attr=0x800000000000000f, range=[0x000000009f066000-0x000000009f067000) (0MB)
[ 0.000000] efi: mem58: type=5, attr=0x800000000000000f, range=[0x000000009f067000-0x000000009f07f000) (0MB)
[ 0.000000] efi: mem59: type=6, attr=0x800000000000000f, range=[0x000000009f07f000-0x000000009f080000) (0MB)
[ 0.000000] efi: mem60: type=5, attr=0x800000000000000f, range=[0x000000009f080000-0x000000009f08b000) (0MB)
[ 0.000000] efi: mem61: type=6, attr=0x800000000000000f, range=[0x000000009f08b000-0x000000009f08c000) (0MB)
[ 0.000000] efi: mem62: type=5, attr=0x800000000000000f, range=[0x000000009f08c000-0x000000009f091000) (0MB)
[ 0.000000] efi: mem63: type=6, attr=0x800000000000000f, range=[0x000000009f091000-0x000000009f092000) (0MB)
[ 0.000000] efi: mem64: type=5, attr=0x800000000000000f, range=[0x000000009f092000-0x000000009f0a0000) (0MB)
[ 0.000000] efi: mem65: type=6, attr=0x800000000000000f, range=[0x000000009f0a0000-0x000000009f0a1000) (0MB)
[ 0.000000] efi: mem66: type=5, attr=0x800000000000000f, range=[0x000000009f0a1000-0x000000009f0f2000) (0MB)
[ 0.000000] efi: mem67: type=6, attr=0x800000000000000f, range=[0x000000009f0f2000-0x000000009f137000) (0MB)
[ 0.000000] efi: mem68: type=5, attr=0x800000000000000f, range=[0x000000009f137000-0x000000009f1bf000) (0MB)
[ 0.000000] efi: mem69: type=6, attr=0x800000000000000f, range=[0x000000009f1bf000-0x000000009f2bf000) (1MB)
[ 0.000000] efi: mem70: type=0, attr=0xf, range=[0x000000009f2bf000-0x000000009f6bf000) (4MB)
[ 0.000000] efi: mem71: type=10, attr=0xf, range=[0x000000009f6bf000-0x000000009f7bf000) (1MB)
[ 0.000000] efi: mem72: type=9, attr=0xf, range=[0x000000009f7bf000-0x000000009f7ff000) (0MB)
[ 0.000000] efi: mem73: type=4, attr=0xf, range=[0x000000009f7ff000-0x000000009f800000) (0MB)
[ 0.000000] efi: mem74: type=7, attr=0xf, range=[0x0000000100000000-0x000000045f000000) (13808MB)
[ 0.000000] efi: mem75: type=0, attr=0x0, range=[0x00000000000a0000-0x00000000000c0000) (0MB)
[ 0.000000] efi: mem76: type=0, attr=0x0, range=[0x000000009f800000-0x00000000a0000000) (8MB)
[ 0.000000] efi: mem77: type=11, attr=0x8000000000000001, range=[0x00000000f0000000-0x00000000f4000000) (64MB)
[ 0.000000] efi: mem78: type=11, attr=0x8000000000000001, range=[0x00000000feb00000-0x00000000feb04000) (0MB)
[ 0.000000] efi: mem79: type=11, attr=0x8000000000000001, range=[0x00000000fec00000-0x00000000fec01000) (0MB)
[ 0.000000] efi: mem80: type=11, attr=0x8000000000000001, range=[0x00000000fed10000-0x00000000fed1a000) (0MB)
[ 0.000000] efi: mem81: type=11, attr=0x8000000000000001, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem82: type=11, attr=0x8000000000000001, range=[0x00000000fee00000-0x00000000fee01000) (0MB)
[ 0.000000] efi: mem83: type=11, attr=0x8000000000000000, range=[0x00000000ffb80000-0x0000000100000000) (4MB)
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: LENOVO 20193/INVALID, BIOS 6BCN42WW(V2.02) 02/08/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x45f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FE0000000 write-back
[ 0.000000] 2 base 09F800000 mask FFF800000 uncachable
[ 0.000000] 3 base 0FF800000 mask FFF800000 write-protect
[ 0.000000] 4 base 100000000 mask F00000000 write-back
[ 0.000000] 5 base 200000000 mask E00000000 write-back
[ 0.000000] 6 base 400000000 mask F80000000 write-back
[ 0.000000] 7 base 45F000000 mask FFF000000 uncachable
[ 0.000000] 8 base 460000000 mask FE0000000 uncachable
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0x9f800 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000082000] 82000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b39000, 0x01b39fff] PGTABLE
[ 0.000000] BRK [0x01b3a000, 0x01b3afff] PGTABLE
[ 0.000000] BRK [0x01b3b000, 0x01b3bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x45ee00000-0x45effffff]
[ 0.000000] [mem 0x45ee00000-0x45effffff] page 2M
[ 0.000000] BRK [0x01b3c000, 0x01b3cfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x45c000000-0x45edfffff]
[ 0.000000] [mem 0x45c000000-0x45edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x400000000-0x45bffffff]
[ 0.000000] [mem 0x400000000-0x45bffffff] page 2M
[ 0.000000] BRK [0x01b3d000, 0x01b3dfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x995affff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x993fffff] page 2M
[ 0.000000] [mem 0x99400000-0x995affff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x9a9b0000-0x9efbefff]
[ 0.000000] [mem 0x9a9b0000-0x9a9fffff] page 4k
[ 0.000000] [mem 0x9aa00000-0x9edfffff] page 2M
[ 0.000000] [mem 0x9ee00000-0x9efbefff] page 4k
[ 0.000000] BRK [0x01b3e000, 0x01b3efff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x9f7ff000-0x9f7fffff]
[ 0.000000] [mem 0x9f7ff000-0x9f7fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x3ffffffff]
[ 0.000000] [mem 0x100000000-0x3ffffffff] page 2M
[ 0.000000] RAMDISK: [mem 0x7f857000-0x7fffffff]
[ 0.000000] ACPI: RSDP 000000009f7fe014 000024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 000000009f7fe210 0000AC (v01 LENOVO CB-01 00000001 01000013)
[ 0.000000] ACPI: FACP 000000009f7fa000 00010C (v05 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DSDT 000000009f7ed000 009D93 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FACS 000000009f7bb000 000040
[ 0.000000] ACPI: SLIC 000000009f7fd000 000176 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: UEFI 000000009f7fc000 000236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASF! 000000009f7fb000 0000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: HPET 000000009f7f9000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 000000009f7f8000 00008C (v03 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 000000009f7f7000 00003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009f7ec000 0006FE (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 000000009f7ea000 000028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASPT 000000009f7e5000 000034 (v07 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DBGP 000000009f7e4000 000034 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FPDT 000000009f7e2000 000044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MSDM 000000009f7e1000 000055 (v03 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009f7e0000 000926 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009f7df000 000B22 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009f7dc000 0010F1 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: BGRT 000000009f7de000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000045effffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x45effffff]
[ 0.000000] NODE_DATA [mem 0x45efea000-0x45efeefff]
[ 0.000000] [ffffea0000000000-ffffea00117fffff] PMD -> [ffff88044e600000-ffff88045e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x45effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x00087fff]
[ 0.000000] node 0: [mem 0x00100000-0x995affff]
[ 0.000000] node 0: [mem 0x9a9b0000-0x9efbefff]
[ 0.000000] node 0: [mem 0x9f7ff000-0x9f7fffff]
[ 0.000000] node 0: [mem 0x100000000-0x45effffff]
[ 0.000000] On node 0 totalpages: 4180807
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 24 pages reserved
[ 0.000000] DMA zone: 3975 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 10031 pages used for memmap
[ 0.000000] DMA32 zone: 641984 pages, LIFO batch:31
[ 0.000000] Normal zone: 55232 pages used for memmap
[ 0.000000] Normal zone: 3534848 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x98579000-0x98579fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x98585000-0x98585fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x98586000-0x98586fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x985ac000-0x985acfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x985ad000-0x985adfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x985d3000-0x985d3fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x995b0000-0x9a9affff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9efbf000-0x9f6befff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f6bf000-0x9f7befff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f7bf000-0x9f7fefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f800000-0x9fffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xa0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xf3ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf4000000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb04000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffb7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffb80000-0xffffffff]
[ 0.000000] e820: [mem 0xa0000000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88045ec00000 s87040 r8192 d23552 u262144
[ 0.000000] pcpu-alloc: s87040 r8192 d23552 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4115456
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: initrd=\initramfs-linux.img root=/dev/sda2 rw quiet nomodeset rcutree.rcu_idle_gp_delay=1 loglevel=3
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16292016K/16723228K available (5230K kernel code, 857K rwdata, 1632K rodata, 1120K init, 1288K bss, 431212K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:744 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 67108864 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2394.558 MHz processor
[ 0.000035] Calibrating delay loop (skipped), value calculated using timer frequency.. 4791.66 BogoMIPS (lpj=7981860)
[ 0.000037] pid_max: default: 32768 minimum: 301
[ 0.000044] ACPI: Core revision 20131218
[ 0.006081] ACPI: All ACPI Tables successfully acquired
[ 0.030009] Security Framework initialized
[ 0.030016] Yama: becoming mindful.
[ 0.031004] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.035068] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.036876] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.036893] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.037118] Initializing cgroup subsys memory
[ 0.037123] Initializing cgroup subsys devices
[ 0.037125] Initializing cgroup subsys freezer
[ 0.037126] Initializing cgroup subsys net_cls
[ 0.037127] Initializing cgroup subsys blkio
[ 0.037150] CPU: Physical Processor ID: 0
[ 0.037151] CPU: Processor Core ID: 0
[ 0.037156] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.037529] mce: CPU supports 9 MCE banks
[ 0.037542] CPU0: Thermal monitoring enabled (TM1)
[ 0.037553] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
tlb_flushall_shift: 2
[ 0.037649] Freeing SMP alternatives memory: 20K (ffffffff819f0000 - ffffffff819f5000)
[ 0.041198] ftrace: allocating 20029 entries in 79 pages
[ 0.050996] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.084028] smpboot: CPU0: Intel(R) Core(TM) i7-3630QM CPU @ 2.40GHz (fam: 06, model: 3a, stepping: 09)
[ 0.084036] TSC deadline timer enabled
[ 0.084045] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events, full-width counters, Intel PMU driver.
[ 0.084051] ... version: 3
[ 0.084052] ... bit width: 48
[ 0.084053] ... generic registers: 4
[ 0.084054] ... value mask: 0000ffffffffffff
[ 0.084055] ... max period: 0000ffffffffffff
[ 0.084056] ... fixed-purpose events: 3
[ 0.084057] ... event mask: 000000070000000f
[ 0.110826] x86: Booting SMP configuration:
[ 0.110828] .... node #0, CPUs: #1
[ 0.124613] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.131276] #2 #3 #4 #5 #6 #7
[ 0.246855] x86: Booted up 1 node, 8 CPUs
[ 0.246859] smpboot: Total of 8 processors activated (38328.30 BogoMIPS)
[ 0.254157] devtmpfs: initialized
[ 0.257424] PM: Registering ACPI NVS region [mem 0x9f6bf000-0x9f7befff] (1048576 bytes)
[ 0.258171] pinctrl core: initialized pinctrl subsystem
[ 0.258207] RTC time: 19:11:33, date: 05/31/14
[ 0.258239] NET: Registered protocol family 16
[ 0.258316] cpuidle: using governor ladder
[ 0.258318] cpuidle: using governor menu
[ 0.258361] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.258362] ACPI: bus type PCI registered
[ 0.258364] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.258425] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.258428] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[ 0.266014] PCI: Using configuration type 1 for base access
[ 0.266838] bio: create slab <bio-0> at 0
[ 0.266930] ACPI: Added _OSI(Module Device)
[ 0.266932] ACPI: Added _OSI(Processor Device)
[ 0.266933] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.266934] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.269731] ACPI: Executed 1 bTrilby wrote:
zacariaz wrote:* b u m p *
Do not do this.
If you want help, start providing relevant information beyond "it don't work". You say you followed the instructions ... which instructions? What steps did you take? It is clear from your xorg.conf that you did not follow the only instructions I could find in the archlinux wiki. Follow those instructions, and post the output of the relevant diagnostic or information-gathering steps included there.
Also if you have information which could be useful - such as which mobile devices/cards allegedly don't work - then share that. Don't keep us in the dark.
I should think that it's quite obvious that I've followed the wiki instruction, which basically is one line in xorg, as is the official nvidia instructions.
This is most likely a problem related specificlally to the gt 650m and/or the lenovo ideapad y500 (and perhaps derivatives thereof).
I do not believe I've left any information out.
Of course if I've done something wrong, I apologize and will do my best to avoid it in the future. As for the rest, I'd very much like to know which instructions I did not follow, as I've done all that I can think of and telling me that I haven't is hardly useful. As far as I aware, the wiki instructs you to ad two line in the xorg.conf, which I've done. I will of course read it again, hoping to figure out what I've apparently missed, though I've read it so many times already that I don't expect to learn anything. -
Will Tablet case with combined keyboard work on Lenovo Ideapad A1 07
Hi All,
Sorry if anyone has asked before but couldn't find specific.
My wife has recently purchased a Lenovo Ideapad A1 07 for its size, a friend who has a small android tablet also recommended to her, to buy a tablet case with combined keyboard with USB connection from amazon. When received the connection obviously doesn't fit, so I started searching around web for an adapter for it, but I’m seeing conflicting info that the ideapad either does/doesn't support USB data transfer connection point, so before buying an adapter what is correct!.
Can anyone throw some light onto whether Lenovo will update the firmware to be able to use USB at any time or has anyone have a work around. Any help and advice to get this keyboard working would be grateful as the tablet is a great little device for her.
GazzatafIf you are patient, go through the reviews of a specific USB keyboard that was suggested as an addition for Lenovo A1 by Amazon: You will see that even though users have tried different cables and adapters, no A1 user has managed to get this working on his tablet.
This issue may be solved by a future upgrade (if any), which will enable the USB OTG feature of the microUSB port of the A1 tablet. Until then, nothing can be done in order to have any USB device identified and working with A1. I really hope that I make a mistake here and that someone will come up with a working soultion for this issue ... -
Black screen with underscore after updating ubuntu on Lenovo G560
hello everybody, I'm new here. I looked for this problem online during the past few days but I haven't found a solution. I have a Lenovo G560 and I divided my hard drive into two partition, I installed Ubuntu on C:\ and Windows on D:\ and I haven't had any problem, but after updating ubuntu to version 14 my computer couldn't boot anymore. the bios loads and I see the Lenovo icon but then I just get a black screen with an underscore (not a blinking underscore), I tried booting from a bootable USB stick but the same thing happened (I put it as the first device to boot from in BIOS settings). can anyone please tell me what are my other options ? what should I try now ? thanks in advance and have a good day !
Hi s, and welcome to Apple Discussions.
Try this:
Hold down the Option+Command (Apple)PR keys, boot/restart your MBP while continuing to hold down those four keys, and after you hear the startup chime for the second time, release the keys. That should reset your PRAM and resolve the issue.
If the issue persists, while you're booted into Open Firmware, just after the prompt, type in:
reset-nvram
then press return, then type in:
reset-all
and press return. This should restart your MBP and it should go back to starting normally. -
Ideapad U510 shuts down instead of sleeping
I have an Ideapad U510 with Windows 8. If I close the screen, or put it into sleep mode, it shuts down. If I walk away from it for a few minutes then it shuts down and I have to wait for it to restart, which is a drag. I've changed every setting I could find under power options on the control panel, nothing seems to change it. I spend a LOT of time waiting for my computer to re-boot. Any suggestions how I can get it to sleep rather than shut down? Thanks for any suggestions.
I have done all of these and reset to factory defaults by One Key Recovery button. At the end I sent it to Lenovo repair center and they claimed they had fixed it by upgrading the Power Mgt software and BIOS, but in the last two days (I received it 3 days ago) it happened twice again. I believe it is a hardware issue. While this is a commonly reported issue for U510, why deosn't Lenovo still have a solution for it?
This is definetly my LAST Lenovo computer and I DO NOT recommand this brand to anyone.
Maybe you are looking for
-
Sending mail through FM : SO_NEW_DOCUMENT_SEND_API1
Dear Friends, I am using the Function Module : SO_NEW_DOCUMENT_SEND_API1 to send mails to MS Outlook. My program is working perfectly fine, when I execute in the foreground. However, when I schedule a job for the same program, it is throwing up an ex
-
I Have a MacBook Pro 2010 that I have put into FireWire target disk mode. Is there any way to just copy the entire hardrive onto my other MacBook Pro rather than going through the entire hard drive and transferring everything separately?
-
Query on Oracle Concepts: Advantages of ASSM
Hi, A query on Oracle Concepts, specifically on Advantages of ASSM. While I am able to understand 'Simplified administration' & 'Increased concurrency', can anyone mention this in simple terms: • Dynamic affinity of space to instances in an Oracle Re
-
Process Task Child Table Delete Event passes empty values
Hi All, I'm trying to implement a delete event in a process task for a child table. I am assuming the value to be deleted should be getting passing into the adapter but it's passing empty strings instead. The insert event is working fine however. Any
-
NetWeaver installation issue with SP13
Hi, I have recently downloaded the complete NetWeaver 2004s Stack13 installation for Windows/MSSQL. I have extraceted all of the folders from the executable zip and copied all of the .sar files from the _1 directory to a temporary directory. Then I