Lenovo IdeaPad Z410 Battery Suddenly Drops From 100% to 0%
I have had my Lenovo IdeaPad Z410 since around January, and I have just recently expierienced the problem of the battery dropping to zero. What happens is my battery will be draining at a normal pace then all of a sudden my laptop will shut down and will not go back on as it thinks the battery is dead. If it is plugged when this happens then the orange battery low light will begin flashing and the message goes from saying "Fully charged (100%)" to "1% remaining (plugged in, charging)". This is quite annoying as I cannot take my laptop anywhere without fear of it randomly dying on me. I would assume I wouldn't need a new battery after only having the laptop for a few months. Also, if you are not familiar with this model, the battery is built in internally so I cannot try removing it and putting it back in myself. Any advice would be appreciated; I'd rather not deal with Lenovo's customer support unless I absolutely have to.
hi LordMothim,
Welcome to the Lenovo Forums.
Based from your findings, it's possible that:
- the battery circuit inside is not working to unload the charge, or
- one of the battery cells have already reached its life span
- the chip that handles how the battery gets charge/discharge and checks the charge level of each battery cell (both are controlled by a firmware) is malfunctioning.
Batteries degrade overtime due to heat and daily use. If you're still under warranty, I recommend you contact lenovo and report the issue as you most likely need a replacement battery.
More info:
How Lithium-ion Batteries Work
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!
Similar Messages
-
I have the 4s and i downloaded ios 8 but nowmy battery will drop from 100 to 0 in 30 mins without me using it. it has also happened to my sisters phone and our upgrade isnt until december. how can i get rid of ios8 for anyting else?
Downgrading the iOS is not supported. Basic troubleshooting steps are restart, reset, restore from backup, restore as new device
-
MBP June 09: Battery Level Drops from 100% to 99% while plugged in !
Hi,
I have noticed that the battery level (indicated in the menu bar) drops from 100% (after recharge) slowly to 99%, then 98% while the machine stays plugged in! I did not let it go further so I don't know if it would further discharge.
I re-calibrated the battery and this is still the case.
Does anybody know if this is normal ? I read on the web that this is due to Apple's battery charging algorithm ...
Thanks for your responses!
Cheers
RainerRainer: Your MBP's charging system is designed so that once the battery has been fully charged, charging stops until the battery level falls below 93%. Then charging resumes. All batteries gradually lose charge as time goes by, without any power being drawn from them by usage. A typical notebook battery loses 0.5% to 1% of its charge per day, even when the machine is completely shut down or when the battery isn't in it (as might be the case for a spare battery). A MBP in normal sleep will lose 1-2% of its battery charge per hour, as some power is used to preserve the contents of RAM in that state. In Safe Sleep, the MBP is essentially shut down and no battery power is used at all, so the loss of charge is limited to the base 0.5%-1% per day.
Under extremely heavy loads (high CPU/GPU usage with maximum screen brightness combined with bus-powered portable drive operation, for example), your MBP may need to draw some power from the battery even while AC power is being supplied. Prolonged use under such conditions could, in theory, completely drain the battery, in which case the CPU clock speed would be automatically reduced to limit power demand to what the AC adapter alone can supply. But the likelihood that you'll ever need to work your machine hard enough for long enough to reach that point is very small. -
My iPhone overheats. Battery drops from 100/90% to 10% sudenly. Got the device 20 days ago. I'm currently living in The Hague, there is no Apple Store in this city, took an appointment in Amsterdam, after 3 hours drive and 60€ travel cost got into the Apple Store, 73 minutes delay on my appointment the Genius tech tells me I should leave my device for further checks in the store and come back in a week or two. Not presicely the answer I was looking for, plus he did not have any device to lend me until my iPhone was checked. Quite dissapointed, Apple was standard for quality on customer satisfaction, in the last 10 years I bought 3 MacBooks, 5 iPdas, 7 iPods, 5 iPhones and 2 iMACs... please don't let me down. [email protected]/[email protected]/[email protected]
Dear Ocean, one is a complaint about the quality of the device.
The second about the quality on response from Customer Service.
No worries, I'll delete both post since it seems that won't bring anything productive.
Good bye Apple! -
I just upgraded my iPad to iOS7 and got battery drain problem. I followed the tips online to turn off all the unneccessary features and seems not working. Because this morning, the battery drops from 100% to 77% in 2.5 hours and I didn't even work on it yet. The smart cover is already closed.
If you followed these steps : http://www.apple.com/ie/batteries/iphone.html , you can attempt to restore your device (back up your information first ,if you don't have a backup) and see if that changes anything. If issue persists , you can contact Applecare and explain the steps you followed . Don't forget to mention that this started happening after you updated to iOS 7 .
-
i got my iphone 5c from like 4 month ago and the last two days the battery lose charge from 100% to 80% while 30 minut without even using it
First you need to back up you iPhone.
Then http://support.apple.com/kb/ht1414 -
after full charge i can use my macbook only for 2hrs and after 20 min my battery percentage decrease from 100% to 87% and it will happend every 20 min .. pls help me
Hi,
How old is your MBP? how many cycle batter do have ?
I will also recomend to use the software http://www.macupdate.com/app/mac/24141/battery-health-monitor
to monitor battery life.
You should be able to read everything from the software.
Please post results.
Regards,
Mirek -
battery goes from 100% charge to 1% charge within secs,now phone won't charge properly or come on or sync with computer
Have you done the following 4Rs basic troubleshooting steps?
Restart:
1. Press and hold the Sleep/Wake button until the red "slide to power off" slider appears, and then slide the slider.
2. Press and hold the Sleep/Wake button until the Apple logo appears.
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data
Restore from backup
Restore as new
http://support.apple.com/kb/HT1414 -
Flex 2 14 Battery Level Dropped from 57 to 7 in seconds
I've been using my Flex 2 14 for around 3 months. However, recently I've encounter a situation whereby my battery level had dropped from 57% to 7% in split second when I'm not plugged in. I was wondering could it be an manufacturing defect and what should I do to fix this problem?
Note: I use this laptop while plugging into the charger most of the time. The battery level is usually kept at around 55~60 only with the help of energy manager. Also, I had performed battery gauge reset once.
Any suggestions will be appreciated.SOLUTION FOUND !
I just found a solution to my battery issue that is apparently due to a bug on the latest update of Snow leopard (10.6.8). Parallels desktop that was in the Dock was making the Dock taking 100% of the CPU activity (checked in the activity monitor) using battery and heating my computer.
After I checked for such cases on teh web (see: http://forums.macrumors.com/showthread.php?t=1181176 ), I removed Parallels Desktop and Windows Applications folder from the Dock and situation seems to be back to normal...
RF -
After installing iOS 6.1.1 & 1day later the so called fix 6.1.2 on my iPhone 4S battery drains from 100% to zero in 2,5 hours. Nothing else has changed.
Sure Aboutaleb THE updates being THE problem. Is it possible to restore iOS 5.xx?The iGO app works now. Just downloaded directly to my phone from AppStore.
-
My I phone 5 got very hot actually boiling hot although it was not exposed to any external heat ...it was fully charged and within 10 minutes it was half charged 50% and within one minute it was shut down ... Tried re charging through the computer and through the power but no response the phone is totally black... Tried connecting to I tunes and no response.. The thing is that I bought the I phone 5 on the 23 rd December 2012 from Manhattan new York and I live in Qatar and there is no service centre in qatar .. I am now without a phone although I paid 706$ and that's a big amount .. I am disappointed .. I bought an original phone from the original apple store and I ended up with a product that didn't survive for a month.. What quality assurance do the apple have on their products...I need help here
I appreciate the fast reply.
Well, I checked the iphone and the battery charged going from the bolt to the plug in the upper right hand corner very quickly. On my other cell phones, charging took a REAL long time.
Again, is this normal? I unplugged the iphone from the charger and I am going to monitor the battery power today. I find it odd that the battery would work on standby for 4 days without recharging the battery and then start doing something wacky. Any thoughts? -
Lenovo U410 Battery Sudden Drop to 0%
Hi guys n girls,
I just got Lenovo U410 Windows 8 in February 2013. This afternoon when i was using the laptop in power saver mode, I was able to use an hour from 60% to 48%. After checking the battery percentage when it was at 48%, 5 minutes later the low battery warning showed up saying the laptop has 6% left, then it shut down itself.
Following are the situations:
I seldom use it and I left it for 1 week plus, and two days ago I used it for 15 minutes, and then I took it out n used it today.
I used it in power saver mode.
I was running the windows update.
Steam was on for updating.
I was running open office.
Is this normal ? Does this happen to others ? IS there a way to solve this ?
Thanks
Solved!
Go to Solution.hi evanicle,
Upon checking the Lenovo Energy Management, the battery gauge can be found in this location (see spoiler)
Spoiler (Highlight to read)
Is this what you see?
Hope this helps
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
[Lenovo IdeaPad S10-3t] Waking up from suspend not working properly
Hi,
I'm having some issues with getting suspend to work on my S10-3t. I tried pm-utils and the s2ram script (with about any combination of options as my machine is not on the whitelist) and always get the same behaviour: Suspending seems to succeed but waking up takes about 5 minutes.
I tried using pm-suspend under ubuntu 10.10, works flawlessly out of the box, so it *can* be done.. somehow.
Apparently this was a kernel related issue in older versions of ubuntu too, I couldn't quite figure out how they fixed it though (https://bugs.launchpad.net/ubuntu/+sour … bug/598664).
I tailed the pm-suspend.log and kernel.log through one suspend/wake up cycle, here's the output:
pm-suspend.log:
bash-4.1$ date;sudo tail -f /var/log/pm-suspend.log
Sun Oct 24 20:27:47 CEST 2010
Password:
Running hook /usr/lib/pm-utils/sleep.d/01grub resume suspend:
/usr/lib/pm-utils/sleep.d/01grub resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave resume suspend:
/usr/lib/pm-utils/sleep.d/00powersave resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging resume suspend:
/usr/lib/pm-utils/sleep.d/00logging resume suspend: success.
Sun Oct 24 20:25:36 CEST 2010: Finished.
tail: /var/log/pm-suspend.log: file truncated
Initial commandline parameters:
Sun Oct 24 20:29:08 CEST 2010: Running hooks for suspend.
Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend:
Linux netarch.haselwarter.org 2.6.35-ARCH #1 SMP PREEMPT Wed Sep 29 07:17:20 UTC 2010 i686 Intel(R) Atom(TM) CPU N470 @ 1.83GHz GenuineIntel GNU/Linux
Module Size Used by
cpufreq_ondemand 6971 2
btusb 9745 0
hid_cando 2611 0
bluetooth 44753 1 btusb
rfkill 12854 1 bluetooth
usbhid 33564 0
hid 60400 2 hid_cando,usbhid
uvcvideo 53488 0
videodev 39124 1 uvcvideo
v4l1_compat 13562 2 uvcvideo,videodev
joydev 7503 0
snd_seq_dummy 1079 0
snd_seq_oss 25072 0
snd_seq_midi_event 4496 1 snd_seq_oss
snd_seq 41752 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 4369 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_hda_codec_conexant 26292 1
snd_pcm_oss 33662 0
i915 267072 2
snd_mixer_oss 14686 1 snd_pcm_oss
snd_hda_intel 19020 0
snd_hda_codec 67274 2 snd_hda_codec_conexant,snd_hda_intel
drm_kms_helper 22043 1 i915
drm 134132 3 i915,drm_kms_helper
snd_hwdep 4764 1 snd_hda_codec
snd_pcm 58308 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
lib80211_crypt_tkip 7521 0
uhci_hcd 19251 0
snd_timer 15423 2 snd_seq,snd_pcm
broadcom 5201 0
i2c_algo_bit 4407 1 i915
ehci_hcd 32860 0
snd 43283 11 snd_seq_oss,snd_seq,snd_seq_device,snd_hda_codec_conexant,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore 5025 1 snd
video 15889 1 i915
wl 1943997 0
tg3 115656 0
usbcore 121737 6 btusb,usbhid,uvcvideo,uhci_hcd,ehci_hcd
output 1448 1 video
snd_page_alloc 5981 2 snd_hda_intel,snd_pcm
intel_agp 24510 2 i915
wmi 5962 0
battery 7879 0
i2c_i801 7426 0
ac 2329 0
i2c_core 15599 6 videodev,i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
psmouse 51529 0
evdev 6820 9
libphy 14543 2 broadcom,tg3
lib80211 3158 2 lib80211_crypt_tkip,wl
agpgart 23520 2 drm,intel_agp
sg 20932 0
thermal 9786 0
coretemp 4665 0
button 3746 1 i915
serio_raw 3566 0
acpi_cpufreq 5157 1
freq_table 1999 2 cpufreq_ondemand,acpi_cpufreq
processor 25126 3 acpi_cpufreq
mperf 979 1 acpi_cpufreq
rtc_cmos 7746 0
rtc_core 11831 1 rtc_cmos
rtc_lib 1494 1 rtc_core
ext4 282610 1
mbcache 4290 1 ext4
jbd2 58396 1 ext4
crc16 1053 1 ext4
sd_mod 26768 3
ahci 17813 0
libahci 16174 3 ahci
libata 140771 2 ahci,libahci
scsi_mod 105888 3 sg,sd_mod,libata
total used free shared buffers cached
Mem: 2053592 233156 1820436 0 24724 102332
-/+ buffers/cache: 106100 1947492
Swap: 1952764 0 1952764
/usr/lib/pm-utils/sleep.d/00logging suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend:
/usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01grub suspend suspend:
/usr/lib/pm-utils/sleep.d/01grub suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend:
/usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/11netcfg suspend suspend:
/usr/lib/pm-utils/sleep.d/11netcfg suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend:
/usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend:
Having NetworkManager put all interaces to sleep...Done.
/usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend:
/usr/lib/pm-utils/sleep.d/75modules suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend:
/usr/lib/pm-utils/sleep.d/90clock suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/91wicd suspend suspend:
Unable to connect to wicd daemon - is it running?
/usr/lib/pm-utils/sleep.d/91wicd suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend:
/usr/lib/pm-utils/sleep.d/95led suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend:
Kernel modesetting video driver detected, not using quirks.
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend:
/usr/lib/pm-utils/sleep.d/99video suspend suspend: success.
Sun Oct 24 20:29:10 CEST 2010: performing suspend
Switching from vt7 to vt1
fbcon fb0 state 1
fbcon fb0 state 0
switching back to vt7
Sun Oct 24 20:34:40 CEST 2010: Awake.
Sun Oct 24 20:34:40 CEST 2010: Running hooks for resume
Running hook /usr/lib/pm-utils/sleep.d/99video resume suspend:
/usr/lib/pm-utils/sleep.d/99video resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend:
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95led resume suspend:
/usr/lib/pm-utils/sleep.d/95led resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/91wicd resume suspend:
Unable to connect to wicd daemon - is it running?
/usr/lib/pm-utils/sleep.d/91wicd resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock resume suspend:
/usr/lib/pm-utils/sleep.d/90clock resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/75modules resume suspend:
Reloaded unloaded modules.
/usr/lib/pm-utils/sleep.d/75modules resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend:
Having NetworkManager wake interfaces back up...Done.
/usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/49bluetooth resume suspend:
/usr/lib/pm-utils/sleep.d/49bluetooth resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/11netcfg resume suspend:
/usr/lib/pm-utils/sleep.d/11netcfg resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01laptop-mode resume suspend:
tail: /var/log/pm-suspend.log: file truncated
Laptop mode
tail: /var/log/pm-suspend.log: file truncated
enabled, not active
Error for wireless request "Set Power Management" (8B2C) :
SET failed on device eth0 ; Operation not supported.
tail: /var/log/pm-suspend.log: file truncated
Failed.
/usr/lib/pm-utils/sleep.d/01laptop-mode resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01grub resume suspend:
/usr/lib/pm-utils/sleep.d/01grub resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave resume suspend:
/usr/lib/pm-utils/sleep.d/00powersave resume suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00logging resume suspend:
/usr/lib/pm-utils/sleep.d/00logging resume suspend: success.
Sun Oct 24 20:34:44 CEST 2010: Finished.
kernel.log:
bash-4.1$ sudo tail -f /var/log/kernel.log
Password:
Oct 24 20:27:15 netarch kernel: input: Cando Corporation Cando 10.1 Multi Touch Panel with Controller as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input9
Oct 24 20:27:15 netarch kernel: cando-touch 0003:2087:0A01.0001: input,hidraw0: USB HID v1.11 Device [Cando Corporation Cando 10.1 Multi Touch Panel with Controller] on usb-0000:00:1d.1-1/input0
Oct 24 20:27:15 netarch kernel: EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
Oct 24 20:27:15 netarch kernel: EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
Oct 24 20:27:15 netarch kernel: Adding 1952764k swap on /dev/sda2. Priority:-1 extents:1 across:1952764k
Oct 24 20:27:16 netarch kernel: tg3 0000:05:00.0: irq 45 for MSI/MSI-X
Oct 24 20:27:16 netarch kernel: tg3 0000:05:00.0: eth0: Link is down
Oct 24 20:27:17 netarch kernel: CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
Oct 24 20:27:18 netarch kernel: tg3 0000:05:00.0: eth0: Link is down
Oct 24 20:27:19 netarch kernel: WARNING! power/level is deprecated; use power/control instead
Oct 24 20:29:08 netarch kernel: CE: hpet increased min_delta_ns to 7500 nsec
Oct 24 20:29:08 netarch kernel: ata1.00: configured for UDMA/100
Oct 24 20:29:08 netarch kernel: ata1: EH complete
Oct 24 20:29:08 netarch kernel: EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
Oct 24 20:34:40 netarch kernel: PM: Syncing filesystems ... done.
Oct 24 20:34:40 netarch kernel: PM: Preparing system for mem sleep
Oct 24 20:34:40 netarch kernel: Freezing user space processes ... (elapsed 0.01 seconds) done.
Oct 24 20:34:40 netarch kernel: Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Oct 24 20:34:40 netarch kernel: PM: Entering mem sleep
Oct 24 20:34:40 netarch kernel: Suspending console(s) (use no_console_suspend to debug)
Oct 24 20:34:40 netarch kernel: sd 0:0:0:0: [sda] Synchronizing SCSI cache
Oct 24 20:34:40 netarch kernel: sd 0:0:0:0: [sda] Stopping disk
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: PCI INT A disabled
Oct 24 20:34:40 netarch kernel: ehci_hcd 0000:00:1d.7: PCI INT A disabled
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.3: PCI INT D disabled
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.2: PCI INT C disabled
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.1: PCI INT B disabled
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.0: PCI INT A disabled
Oct 24 20:34:40 netarch kernel: tg3 0000:05:00.0: PME# enabled
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: wake-up capability enabled by ACPI
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: PCI INT A disabled
Oct 24 20:34:40 netarch kernel: ACPI handle has no context!
Oct 24 20:34:40 netarch kernel: PM: suspend of devices complete after 429.517 msecs
Oct 24 20:34:40 netarch kernel: PM: late suspend of devices complete after 13.649 msecs
Oct 24 20:34:40 netarch kernel: ACPI: Preparing to enter system sleep state S3
Oct 24 20:34:40 netarch kernel: PM: Saving platform NVS memory
Oct 24 20:34:40 netarch kernel: Disabling non-boot CPUs ...
Oct 24 20:34:40 netarch kernel: CPU 1 is now offline
Oct 24 20:34:40 netarch kernel: SMP alternatives: switching to UP code
Oct 24 20:34:40 netarch kernel: Extended CMOS year: 2000
Oct 24 20:34:40 netarch kernel: Back to C!
Oct 24 20:34:40 netarch kernel: PM: Restoring platform NVS memory
Oct 24 20:34:40 netarch kernel: CPU0: Thermal monitoring handled by SMI
Oct 24 20:34:40 netarch kernel: Extended CMOS year: 2000
Oct 24 20:34:40 netarch kernel: Enabling non-boot CPUs ...
Oct 24 20:34:40 netarch kernel: SMP alternatives: switching to SMP code
Oct 24 20:34:40 netarch kernel: Booting Node 0 Processor 1 APIC 0x1
Oct 24 20:34:40 netarch kernel: Initializing CPU#1
Oct 24 20:34:40 netarch kernel: CPU1 is up
Oct 24 20:34:40 netarch kernel: ACPI: Waking up from system sleep state S3
Oct 24 20:34:40 netarch kernel: ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20100428/evregion-474)
Oct 24 20:34:40 netarch kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_.DSLD] (Node f7025600), AE_TIME
Oct 24 20:34:40 netarch kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_WAK] (Node f7024768), AE_TIME
Oct 24 20:34:40 netarch kernel: ACPI Exception: AE_TIME, During Method _WAK (20100428/hwsleep-601)
Oct 24 20:34:40 netarch kernel: i915 0000:00:02.0: restoring config space at offset 0x1 (was 0x900007, writing 0x900407)
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100104, writing 0x100102)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x40100, writing 0x4010b)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0x80118001)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xf010f010)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0x20000000, writing 0x2020)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0xf (was 0x40200, writing 0x40207)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0x80318021)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xf020f020)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0x7 (was 0x20000000, writing 0x3030)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.3: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
Oct 24 20:34:40 netarch kernel: ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
Oct 24 20:34:40 netarch kernel: pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
Oct 24 20:34:40 netarch kernel: pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0xfff0)
Oct 24 20:34:40 netarch kernel: ahci 0000:00:1f.2: restoring config space at offset 0xf (was 0x200, writing 0x20a)
Oct 24 20:34:40 netarch kernel: ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
Oct 24 20:34:40 netarch kernel: tg3 0000:05:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
Oct 24 20:34:40 netarch kernel: tg3 0000:05:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x40100506)
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0200004)
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100106)
Oct 24 20:34:40 netarch kernel: PM: early resume of devices complete after 2.675 msecs
Oct 24 20:34:40 netarch kernel: i915 0000:00:02.0: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.0: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: usb usb2: root hub lost power or was reset
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.1: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: usb usb3: root hub lost power or was reset
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.2: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: usb usb4: root hub lost power or was reset
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
Oct 24 20:34:40 netarch kernel: uhci_hcd 0000:00:1d.3: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: usb usb5: root hub lost power or was reset
Oct 24 20:34:40 netarch kernel: ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Oct 24 20:34:40 netarch kernel: ehci_hcd 0000:00:1d.7: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: pci 0000:00:1e.0: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: ahci 0000:00:1f.2: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: pcieport 0000:00:1c.0: wake-up capability disabled by ACPI
Oct 24 20:34:40 netarch kernel: tg3 0000:05:00.0: PME# disabled
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Oct 24 20:34:40 netarch kernel: wl 0000:07:00.0: setting latency timer to 64
Oct 24 20:34:40 netarch kernel: sd 0:0:0:0: [sda] Starting disk
Oct 24 20:34:40 netarch kernel: ata2: SATA link down (SStatus 0 SControl 300)
Oct 24 20:34:40 netarch kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Oct 24 20:34:40 netarch kernel: usb 3-2: reset full speed USB device using uhci_hcd and address 3
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: btusb 3-2:1.0: no reset_resume for driver btusb?
Oct 24 20:34:40 netarch kernel: btusb 3-2:1.1: no reset_resume for driver btusb?
Oct 24 20:34:40 netarch kernel: usb 1-8: reset high speed USB device using ehci_hcd and address 4
Oct 24 20:34:40 netarch kernel: ata1.00: configured for UDMA/100
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: usb 3-1: reset full speed USB device using uhci_hcd and address 2
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: PM: resume of devices complete after 996.313 msecs
Oct 24 20:34:40 netarch kernel: PM: Finishing wakeup.
Oct 24 20:34:40 netarch kernel: Restarting tasks ...
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: done.
Oct 24 20:34:40 netarch kernel: video LNXVIDEO:00: Restoring backlight state
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
Oct 24 20:34:40 netarch kernel: atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Oct 24 20:34:40 netarch kernel: tg3 0000:05:00.0: eth0: Link is down
Oct 24 20:34:41 netarch kernel: tg3 0000:05:00.0: eth0: Link is down
Oct 24 20:34:43 netarch kernel: ata1.00: configured for UDMA/100
Oct 24 20:34:43 netarch kernel: ata1: EH complete
Oct 24 20:34:44 netarch kernel: EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
dmesg:
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.35-ARCH (tobias@T-POWA-LX) (gcc version 4.5.1 (GCC) ) #1 SMP PREEMPT Wed Sep 29 07:17:20 UTC 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f5d0000 (usable)
BIOS-e820: 000000007f5d0000 - 000000007f5e0000 (ACPI data)
BIOS-e820: 000000007f5e0000 - 000000007f5e3000 (ACPI NVS)
BIOS-e820: 000000007f5e3000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
DMI 2.5 present.
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x7f5d0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-D3FFF write-protect
D4000-DFFFF uncachable
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask 080000000 write-back
1 base 07F600000 mask 0FFE00000 uncachable
2 base 07F800000 mask 0FF800000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 0000000000002000 - 0000000000010000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000001000 (reserved)
modified: 0000000000001000 - 0000000000002000 (usable)
modified: 0000000000002000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009dc00 (usable)
modified: 000000000009dc00 - 00000000000a0000 (reserved)
modified: 00000000000d2000 - 00000000000d4000 (reserved)
modified: 00000000000dc000 - 00000000000e0000 (reserved)
modified: 00000000000e4000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007f5d0000 (usable)
modified: 000000007f5d0000 - 000000007f5e0000 (ACPI data)
modified: 000000007f5e0000 - 000000007f5e3000 (ACPI NVS)
modified: 000000007f5e3000 - 0000000080000000 (reserved)
modified: 00000000e0000000 - 00000000f0000000 (reserved)
modified: 00000000fec00000 - 00000000fec10000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000ff000000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
found SMP MP-table at [c00f7cb0] f7cb0
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 15000-1a000
RAMDISK: 37e2a000 - 37ff0000
Allocated new RAMDISK: 00100000 - 002c5f93
Move RAMDISK from 0000000037e2a000 - 0000000037feff92 to 00100000 - 002c5f92
ACPI: RSDP 000f7c80 00024 (v04 PTLTD )
ACPI: XSDT 7f5d72d4 00074 (v01 LENOVO CB-01 06040000 LTP 00000000)
ACPI: FACP 7f5dfc60 000F4 (v03 LENOVO CB-01 06040000 PTL 00000002)
ACPI: DSDT 7f5d846a 07782 (v01 LENOVO CB-01 06040000 MSFT 03000000)
ACPI: FACS 7f5e2fc0 00040
ACPI: TCPA 7f5dfd54 00032 (v01 Phoeni x 06040000 TL 00000000)
ACPI: MCFG 7f5dfd86 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
ACPI: HPET 7f5dfdc2 00038 (v01 PTLTD HPETTBL 06040000 LTP 00000001)
ACPI: APIC 7f5dfdfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: BOOT 7f5dfe62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
ACPI: SLIC 7f5dfe8a 00176 (v01 LENOVO CB-01 06040000 LTP 00000000)
ACPI: SSDT 7f5d78ca 0025F (v01 PmRef Cpu0Tst 00003000 INTL 20050624)
ACPI: SSDT 7f5d7824 000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20050624)
ACPI: SSDT 7f5d7348 004DC (v02 PmRef CpuPm 00003000 INTL 20050624)
ACPI: Local APIC address 0xfee00000
1149MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
Zone PFN ranges:
DMA 0x00000001 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007f5d0
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000001 -> 0x00000002
0: 0x00000010 -> 0x0000009d
0: 0x00000100 -> 0x0007f5d0
On node 0 totalpages: 521566
free_area_init_node: node 0, pgdat c1418ac0, node_mem_map c157b020
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3950 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2300 pages used for memmap
HighMem zone: 292054 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0xffffffff base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
early_res array is doubled to 64 at [16000 - 167ff]
PM: Registered nosave memory: 0000000000002000 - 0000000000010000
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 14 pages/cpu @c2800000 s34880 r0 d22464 u2097152
pcpu-alloc: s34880 r0 d22464 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517490
Kernel command line: BOOT_IMAGE=/boot/vmlinuz26 root=/dev/sda5
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
allocated 10433580 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Subtract (53 early reservations)
#1 [0000001000 - 0000002000] EX TRAMPOLINE
#2 [0001000000 - 0001572184] TEXT DATA BSS
#3 [0001573000 - 000157921c] BRK
#4 [00000f7cc0 - 0000100000] BIOS reserved
#5 [00000f7cb0 - 00000f7cc0] MP-table mpf
#6 [000009dc00 - 000009e071] BIOS reserved
#7 [000009e199 - 00000f7cb0] BIOS reserved
#8 [000009e071 - 000009e199] MP-table mpc
#9 [0000010000 - 0000011000] TRAMPOLINE
#10 [0000011000 - 0000015000] ACPI WAKEUP
#11 [0000015000 - 0000016000] PGTABLE
#12 [0000100000 - 00002c6000] NEW RAMDISK
#13 [000157a000 - 000157b000] BOOTMEM
#14 [000157b000 - 000256b000] BOOTMEM
#15 [00015721c0 - 00015721c4] BOOTMEM
#16 [0001572200 - 00015722c0] BOOTMEM
#17 [00015722c0 - 0001572314] BOOTMEM
#18 [000256b000 - 000256e000] BOOTMEM
#19 [0001572340 - 00015723ac] BOOTMEM
#20 [000256e000 - 0002574000] BOOTMEM
#21 [00015723c0 - 00015723e5] BOOTMEM
#22 [0001572400 - 0001572427] BOOTMEM
#23 [0001572440 - 0001572600] BOOTMEM
#24 [0001572600 - 0001572640] BOOTMEM
#25 [0001572640 - 0001572680] BOOTMEM
#26 [0001572680 - 00015726c0] BOOTMEM
#27 [00015726c0 - 0001572700] BOOTMEM
#28 [0001572700 - 0001572740] BOOTMEM
#29 [0001572740 - 0001572780] BOOTMEM
#30 [0001572780 - 00015727c0] BOOTMEM
#31 [00015727c0 - 0001572800] BOOTMEM
#32 [0001572800 - 0001572840] BOOTMEM
#33 [0001572840 - 0001572880] BOOTMEM
#34 [0001572880 - 00015728c0] BOOTMEM
#35 [00015728c0 - 0001572900] BOOTMEM
#36 [0001572900 - 0001572940] BOOTMEM
#37 [0001572940 - 0001572950] BOOTMEM
#38 [0001572980 - 0001572990] BOOTMEM
#39 [00015729c0 - 00015729ea] BOOTMEM
#40 [0001572a00 - 0001572a2a] BOOTMEM
#41 [0002800000 - 000280e000] BOOTMEM
#42 [0002a00000 - 0002a0e000] BOOTMEM
#43 [0001572a40 - 0001572a44] BOOTMEM
#44 [0001572a80 - 0001572a84] BOOTMEM
#45 [0001572ac0 - 0001572ac8] BOOTMEM
#46 [0001572b00 - 0001572b08] BOOTMEM
#47 [0001572b40 - 0001572be8] BOOTMEM
#48 [0001572c00 - 0001572c68] BOOTMEM
#49 [0002574000 - 0002578000] BOOTMEM
#50 [0002578000 - 00025f8000] BOOTMEM
#51 [00025f8000 - 0002638000] BOOTMEM
#52 [0002a0e000 - 000340142c] BOOTMEM
Initializing HighMem for node 0 (000377fe:0007f5d0)
Memory: 2051364k/2086720k available (2986k kernel code, 34900k reserved, 1238k data, 412k init, 1177416k highmem)
virtual kernel memory layout:
fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1421000 - 0xc1488000 ( 412 kB)
.data : 0xc12eaacc - 0xc1420340 (1238 kB)
.text : 0xc1000000 - 0xc12eaacc (2986 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:512
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1828.625 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3658.63 BogoMIPS (lpj=6095416)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
... version: 3
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
ACPI: Core revision 20100428
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Atom(TM) CPU N470 @ 1.83GHz stepping 0a
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (7317.54 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-10] at [mem 0xe0000000-0xe10fffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xe10fffff] reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: SSDT 7f5d8193 00203 (v02 PmRef Cpu0Ist 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00203 (v02 PmRef Cpu0Ist 00003000 INTL 20050624)
ACPI: SSDT 7f5d7b29 005E5 (v02 PmRef Cpu0Cst 00003001 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 005E5 (v02 PmRef Cpu0Cst 00003001 INTL 20050624)
ACPI: SSDT 7f5d8396 000D4 (v02 PmRef Cpu1Ist 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 000D4 (v02 PmRef Cpu1Ist 00003000 INTL 20050624)
ACPI: SSDT 7f5d810e 00085 (v02 PmRef Cpu1Cst 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00085 (v02 PmRef Cpu1Cst 00003000 INTL 20050624)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701f390), AE_ALREADY_EXISTS
ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xf7ffffff]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xfdff]
pci 0000:00:02.0: reg 10: [mem 0xf0300000-0xf037ffff]
pci 0000:00:02.0: reg 14: [io 0x18e8-0x18ef]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref]
pci 0000:00:02.0: reg 1c: [mem 0xf0000000-0xf00fffff]
pci 0000:00:02.1: reg 10: [mem 0xf0380000-0xf03fffff]
pci 0000:00:1b.0: reg 10: [mem 0xf0400000-0xf0403fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0x1820-0x183f]
pci 0000:00:1d.1: reg 20: [io 0x1840-0x185f]
pci 0000:00:1d.2: reg 20: [io 0x1860-0x187f]
pci 0000:00:1d.3: reg 20: [io 0x1880-0x189f]
pci 0000:00:1d.7: reg 10: [mem 0xf0604000-0xf06043ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: reg 10: [io 0x18e0-0x18e7]
pci 0000:00:1f.2: reg 14: [io 0x18d4-0x18d7]
pci 0000:00:1f.2: reg 18: [io 0x18d8-0x18df]
pci 0000:00:1f.2: reg 1c: [io 0x18d0-0x18d3]
pci 0000:00:1f.2: reg 20: [io 0x18c0-0x18cf]
pci 0000:00:1f.2: reg 24: [mem 0xf0604400-0xf06047ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20: [io 0x18a0-0x18bf]
pci 0000:05:00.0: reg 10: [mem 0xf0100000-0xf010ffff 64bit]
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.0: PCI bridge to [bus 05-05]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xf0100000-0xf01fffff]
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:07:00.0: reg 10: [mem 0xf0200000-0xf0203fff 64bit]
pci 0000:07:00.0: supports D1 D2
pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:00:1c.1: PCI bridge to [bus 07-07]
pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.1: bridge window [mem 0xf0200000-0xf02fffff]
pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: PCI bridge to [bus 11-11] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x80000000-0xf7ffffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xfdff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701f390), AE_ALREADY_EXISTS
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
HEST: Table is not found!
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 0000000000002000 - 000000000000ffff
reserve RAM buffer: 000000000009dc00 - 000000000009ffff
reserve RAM buffer: 000000007f5d0000 - 000000007fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: [io 0x0800-0x080f] has been reserved
system 00:01: [io 0x1000-0x107f] has been reserved
system 00:01: [io 0x1180-0x11bf] has been reserved
system 00:01: [io 0x04d0-0x04d1] has been reserved
system 00:01: [io 0xfe00] has been reserved
system 00:01: [io 0x0700-0x070f] has been reserved
system 00:01: [io 0x164e-0x174c] has been reserved
system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
system 00:01: [mem 0xfef00000-0xfeffffff] has been reserved
pci 0000:00:1c.0: BAR 15: assigned [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1c.1: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
pci 0000:00:1c.1: BAR 13: assigned [io 0x3000-0x3fff]
pci 0000:00:1c.0: PCI bridge to [bus 05-05]
pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1c.0: bridge window [mem 0xf0100000-0xf01fffff]
pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1c.1: PCI bridge to [bus 07-07]
pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
pci 0000:00:1c.1: bridge window [mem 0xf0200000-0xf02fffff]
pci 0000:00:1c.1: bridge window [mem 0x80200000-0x803fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 11-11]
pci 0000:00:1e.0: bridge window [io disabled]
pci 0000:00:1e.0: bridge window [mem disabled]
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: enabling device (0000 -> 0003)
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 6 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 7 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 8 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:00: resource 9 [mem 0x80000000-0xf7ffffff]
pci_bus 0000:00: resource 10 [io 0x0d00-0xfdff]
pci_bus 0000:05: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:05: resource 1 [mem 0xf0100000-0xf01fffff]
pci_bus 0000:05: resource 2 [mem 0x80000000-0x801fffff 64bit pref]
pci_bus 0000:07: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:07: resource 1 [mem 0xf0200000-0xf02fffff]
pci_bus 0000:07: resource 2 [mem 0x80200000-0x803fffff 64bit pref]
pci_bus 0000:11: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:11: resource 5 [mem 0x000a0000-0x000bffff]
pci_bus 0000:11: resource 6 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:11: resource 7 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:11: resource 8 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:11: resource 9 [mem 0x80000000-0xf7ffffff]
pci_bus 0000:11: resource 10 [io 0x0d00-0xfdff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 32 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 1816k freed
Simple Boot Flag at 0x36 set to 0x1
apm: BIOS not found.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1287944823.419:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1710
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
ERST: Table is not found!
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Resume from disk failed.
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 412k freed
udev[38]: starting version 162
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
SCSI subsystem initialized
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604500 irq 42
ata2: SATA max UDMA/133 abar m1024@0xf0604400 port 0xf0604580 irq 42
ata3: DUMMY
ata4: DUMMY
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: ST9250315AS, 0010LVM1, max UDMA/100
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST9250315AS 0010 PQ: 0 ANSI: 5
ata2: SATA link down (SStatus 0 SControl 300)
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 sda5
sd 0:0:0:0: [sda] Attached SCSI disk
PM: Marking nosave pages: 0000000000002000 - 0000000000010000
PM: Marking nosave pages: 000000000009d000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
udev[734]: starting version 162
ACPI: acpi_idle registered with cpuidle
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
Marking TSC unstable due to TSC halts in idle
Switching to clocksource hpet
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
coretemp coretemp.0: Unable to read TjMax from CPU.
coretemp coretemp.0: Using relative temperature scale!
ACPI: Lid Switch [LID]
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:583 proc_register+0xf8/0x1e0()
Hardware name: 20040M18
proc_dir_entry 'power/PWRB' already registered
Modules linked in: coretemp button(+) serio_raw acpi_cpufreq freq_table processor mperf rtc_cmos rtc_core rtc_lib ext4 mbcache jbd2 crc16 sd_mod ahci libahci libata scsi_mod
Pid: 1097, comm: modprobe Not tainted 2.6.35-ARCH #1
Call Trace:
[<c10439bd>] warn_slowpath_common+0x6d/0xa0
[<c113e648>] ? proc_register+0xf8/0x1e0
[<c113e648>] ? proc_register+0xf8/0x1e0
[<c1043a6e>] warn_slowpath_fmt+0x2e/0x30
[<c113e648>] proc_register+0xf8/0x1e0
[<c113eca3>] proc_mkdir_mode+0x33/0x50
[<c113eccf>] proc_mkdir+0xf/0x20
[<f82af453>] acpi_button_add+0x21b/0x387 [button]
[<c11cc665>] acpi_device_probe+0x3a/0xf4
[<c121eae7>] driver_probe_device+0x77/0x180
[<c121ec69>] __driver_attach+0x79/0x80
[<c121dcb3>] bus_for_each_dev+0x43/0x70
[<c121e839>] driver_attach+0x19/0x20
[<c121ebf0>] ? __driver_attach+0x0/0x80
[<c121e3ed>] bus_add_driver+0xbd/0x2e0
[<c11cc59b>] ? acpi_device_remove+0x0/0x90
[<c121ee65>] driver_register+0x65/0x110
[<c113eca3>] ? proc_mkdir_mode+0x33/0x50
[<c11ccd53>] acpi_bus_register_driver+0x3a/0x3c
[<f82b202b>] acpi_button_init+0x2b/0x4a [button]
[<c100120d>] do_one_initcall+0x2d/0x190
[<f82b2000>] ? acpi_button_init+0x0/0x4a [button]
[<c107892b>] sys_init_module+0x9b/0x1e0
[<c10f4f8f>] ? sys_close+0x6f/0xc0
[<c100379f>] sysenter_do_call+0x12/0x28
---[ end trace 475801f928d07a3d ]---
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:01/input/input3
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
ACPI: Power Button [PWRF]
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ01] (60 C)
sd 0:0:0:0: Attached scsi generic sg0 type 0
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
Linux agpgart interface v0.103
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ACPI: AC Adapter [ACAD] (on-line)
wl: module license 'Mixed/Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: WMI: Mapper loaded
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
agpgart-intel 0000:00:00.0: detected 8188K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
tg3.c:v3.110 (April 9, 2010)
tg3 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
tg3 0000:05:00.0: setting latency timer to 64
wl 0000:07:00.0: enabling device (0104 -> 0106)
wl 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
wl 0000:07:00.0: setting latency timer to 64
ACPI: Battery Slot [BAT1] (battery present)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0604000
tg3 mdio bus: probed
tg3 0000:05:00.0: eth1: Tigon3 [partno(BCM57780) rev 57780001] (PCI Express) MAC address c8:0a:a9:3b:be:4d
tg3 0000:05:00.0: eth1: attached PHY driver [Broadcom BCM57780] (mii_bus:phy_addr=500:01)
tg3 0000:05:00.0: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
tg3 0000:05:00.0: eth1: dma_rwctrl[76180000] dma_mask[64-bit]
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
lib80211_crypt: registered algorithm 'TKIP'
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.60.48.36
udev[757]: renamed network interface eth1 to eth1-eth0
udev[756]: renamed network interface eth0 to wlan0
udev[757]: renamed network interface eth1-eth0 to eth0
[drm] Initialized drm 1.1.0 20060810
HDA Intel 0000:00:1b.0: enabling device (0104 -> 0106)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
usb 1-8: new high speed USB device using ehci_hcd and address 4
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
i915 0000:00:02.0: irq 44 for MSI/MSI-X
[drm] set up 7M of stolen space
Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04771/0xa40000/0x4a0500
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input6
usb 3-1: new full speed USB device using uhci_hcd and address 2
[drm] initialized overlay support
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (04f2:b1a1)
input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input7
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
usb 3-2: new full speed USB device using uhci_hcd and address 3
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Console: switching to colour frame buffer device 128x37
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
Slow work thread pool: Starting up
Slow work thread pool: Ready
ACPI Warning: _BQC returned an invalid level (20100428/video-640)
acpi device:03: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
input: Cando Corporation Cando 10.1 Multi Touch Panel with Controller as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input9
cando-touch 0003:2087:0A01.0001: input,hidraw0: USB HID v1.11 Device [Cando Corporation Cando 10.1 Multi Touch Panel with Controller] on usb-0000:00:1d.1-1/input0
EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
Adding 1952764k swap on /dev/sda2. Priority:-1 extents:1 across:1952764k
tg3 0000:05:00.0: irq 45 for MSI/MSI-X
tg3 0000:05:00.0: eth0: Link is down
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
tg3 0000:05:00.0: eth0: Link is down
WARNING! power/level is deprecated; use power/control instead
CE: hpet increased min_delta_ns to 7500 nsec
ata1.00: configured for UDMA/100
ata1: EH complete
EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
wl 0000:07:00.0: PCI INT A disabled
ehci_hcd 0000:00:1d.7: PCI INT A disabled
uhci_hcd 0000:00:1d.3: PCI INT D disabled
uhci_hcd 0000:00:1d.2: PCI INT C disabled
uhci_hcd 0000:00:1d.1: PCI INT B disabled
uhci_hcd 0000:00:1d.0: PCI INT A disabled
tg3 0000:05:00.0: PME# enabled
pcieport 0000:00:1c.0: wake-up capability enabled by ACPI
HDA Intel 0000:00:1b.0: PCI INT A disabled
ACPI handle has no context!
PM: suspend of devices complete after 429.517 msecs
PM: late suspend of devices complete after 13.649 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
Extended CMOS year: 2000
Back to C!
PM: Restoring platform NVS memory
CPU0: Thermal monitoring handled by SMI
Extended CMOS year: 2000
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting Node 0 Processor 1 APIC 0x1
Initializing CPU#1
CPU1 is up
ACPI: Waking up from system sleep state S3
ACPI Exception: AE_TIME, Returned by Handler for [EmbeddedControl] (20100428/evregion-474)
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_.DSLD] (Node f7025600), AE_TIME
ACPI Error (psparse-0537): Method parse/execution failed [\_WAK] (Node f7024768), AE_TIME
ACPI Exception: AE_TIME, During Method _WAK (20100428/hwsleep-601)
i915 0000:00:02.0: restoring config space at offset 0x1 (was 0x900007, writing 0x900407)
HDA Intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100104, writing 0x100102)
pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x40100, writing 0x4010b)
pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0x80118001)
pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xf010f010)
pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0x20000000, writing 0x2020)
pcieport 0000:00:1c.0: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
pcieport 0000:00:1c.1: restoring config space at offset 0xf (was 0x40200, writing 0x40207)
pcieport 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0x80318021)
pcieport 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xf020f020)
pcieport 0000:00:1c.1: restoring config space at offset 0x7 (was 0x20000000, writing 0x3030)
pcieport 0000:00:1c.1: restoring config space at offset 0x3 (was 0x810000, writing 0x810008)
pcieport 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1d.3: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0xfff0)
ahci 0000:00:1f.2: restoring config space at offset 0xf (was 0x200, writing 0x20a)
ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
tg3 0000:05:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
tg3 0000:05:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x40100506)
wl 0000:07:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
wl 0000:07:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0200004)
wl 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
wl 0000:07:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100106)
PM: early resume of devices complete after 2.675 msecs
i915 0000:00:02.0: setting latency timer to 64
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb2: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb4: root hub lost power or was reset
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
usb usb5: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
ahci 0000:00:1f.2: setting latency timer to 64
pcieport 0000:00:1c.0: wake-up capability disabled by ACPI
tg3 0000:05:00.0: PME# disabled
wl 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
wl 0000:07:00.0: setting latency timer to 64
sd 0:0:0:0: [sda] Starting disk
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
usb 3-2: reset full speed USB device using uhci_hcd and address 3
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
btusb 3-2:1.0: no reset_resume for driver btusb?
btusb 3-2:1.1: no reset_resume for driver btusb?
usb 1-8: reset high speed USB device using ehci_hcd and address 4
ata1.00: configured for UDMA/100
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
usb 3-1: reset full speed USB device using uhci_hcd and address 2
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
PM: resume of devices complete after 996.313 msecs
PM: Finishing wakeup.
Restarting tasks ...
atkbd serio0: Unknown key released (translated set 2, code 0x7c on isa0060/serio0).
atkbd serio0: Use 'setkeycodes 7c <keycode>' to make it known.
donekorpenkraxar wrote:
Try this with a kernel 3.X version:
hpet=disable highres=off nohz=off
I have been trying to resolve the issue of suspend failing to resume on me Lenovo s10-3 (not the touch screen) for what seems an aeon.
A profound thank you to you all.
hpet=disable highres=off nohz=off
Works!
I now have no indication lights showing when the machine is suspended? But finally I can close the lid and reopen to resume - fantastic, this machine may finally see some more use.
I am running Linux Mint Debian Edition (LMDE) running Gnome 3 with 3 series kernels (presently liquorix 3.4.0-4.dmz.1-liquorix-686) -
Iphone 4s battery sudden drainage from 38% to 1%
Dear friends,
from today morning my iPhone is suddenly getting switched off at 38% and when i am trying to turn it on it is showing to plug it to the power adapter.
at 1%
now at about 9:50 pm the problem is arising again . pls helpWell, most of what you did is black magic, and has nothing to do with battery drain. But we have no way of knowing how your battery life is below what you think it should be. What are you using it for, what apps do you have, and how much Usage life do you get (settings/general/usage).
-
Thinkpad T60 battery sudden drop
Hey,
I bought a T60 Sep 2007. Recently I am having a problem with battery life.(My battery is not on the list of recall)
My battery life went down drastically. It used to be a couple of hours, now it's less than half an hour. Power mangment reports a copule of hours remaining, until it gets down to about 85%-90%, and then suddently drop to 5% and a few minutes remaining.
I seldom use battery and most of time use AC. Interstingly, after charging my battery to 20% or 30%, it can last for half an hour or so. So I suspect there is something wrong with software rather than a physical problem.
Any comments or solutions?That type of behaviour is typical if one or more cells in the battery are bad. You should look into replacement options.
What condition does Power Manager report for the battery?
Good luck andlet us know.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.
Maybe you are looking for
-
How to add email antivirus protection to 10.3.9?
How can a 10.3.9 Server be upgraded to add antivirus protection to our email server?
-
Advance pricing for combined item rate
Hi all, We are running oracle ebs 11i with database 10 , Our management introduce new rate list and this rate list depends on the other items quantity. You can say it combine price list. Suppose we have two items A and B. Normal price list : item qua
-
QuickTime export in 2 same as 1
Hi! I had this issue when doing transitions in Keynote to QuickTime where it did the slide show as a click to continue function, but when it reached the frame before the hold frame it would stop. This results in seeing both frames laid over the top o
-
Hello, We are FDM 11.1.2.1 and are having an issue when importing a journal template (Excel 97-2003 format). After checking in the journal and hitting "Post" we get an error message "Error: File Import Failed. Detail: File not found". I checked and d
-
Datafiles, logfiles, control files, etc. not deleted from OS
Hello, I used the Database Configuration Assistant to create a database(v9.2) and at a later time deleted the database also using the DBCA. Why aren't the datafiles, control files, logfiles, etc. deleted from the Windows OS files. Doesn't the DBCA de