Lenovo ideaphone S920 Link to PC problem

Hi, Am using Lenovo ideaphone S920. Its not getting deducted if I connect the phone through USB cable with my PC. There is no pop up in the phone or no drive additon in my PC though. The phone starts charging through USB power.
Before this problem, I done factory re-set to free divice storage size. Any urgent help pls...

Now I'm unable to see the Developer option also at - setting>all setting> ......
Earlier I did this step. But didnt helped me.
I took the phone to service mcentre and they corrected it. But again (just after few days) the PC not detecting the phone through USB cable. ((((

Similar Messages

Where is the link for submitting problem to apple?

Where is apple link for submitting problems?

Hi,
Was this the link your looking for
http://www.apple.com/feedback/iphone.html
Dale

Solaris 8 says: "Link down, Cable Problem?"

I have these on my home LAN:
1. Sun Ultra 5 Solaris 8
2. Win 2000 PC
3. Win NT laptop
They are all hooked into a LinkSys Router.
The Router is hooked into my Motorala Cable Modem.
Here's the problem:
The PC and the laptop can see each other on the LAN.
The Solaris 8 is only visible on the Lan INTERMITTENTLY.
The lights on the Router for the PC and laptop are always ON.
When I reboot the Solaris box, the lights on the Router sometimes come ON, and sometimes they stay OFF. When they stay OFF, I see the message: "Link down, Cable Problem?" during reboot.
I have tried different cables, and tried various combinations of the 4 avalable ports on the back of my Router.
If I plug in the Sun box DIRECTLY into my cable modem, then I don't see the above message. (but then I don't have a LAN anymore)
Please help, I've been struggling with this for a while now.
Thanks,
Irshad Ahmed (I am relatively new to Sun)

Hi
You have not indicated if you have the router ethernet ports working
at 100Mbps or 10Mbps. Depending on this sometimes, Sun systems may
not be correctly auto-negotiating their ethernet port settings.
You may set these parameters to force Sun Ultra 5 to a 100Mbps mode or a 10Mbps mode.
For forcing it to 100Mbps, Full Duplex mode and disabling the auto-negotiation, put these entries in /etc/system:
set hme:hme_adv_autoneg_cap=0
set hme:hme_adv_100T4_cap=0
set hme:hme_adv_100fdx_cap=1
set hme:hme_adv_100hdx_cap=0
set hme:hme_adv_10fdx_cap=0
set hme:hme_adv_10hdx_cap=0
Conversely, if you want to force your Sun to work on 10Mbps, Full
duplex mode, (if your router does not support 100Mbps) in the same
/etc/system file, put the following entries :
set hme:hme_adv_autoneg_cap=0
set hme:hme_adv_100T4_cap=0
set hme:hme_adv_100fdx_cap=0
set hme:hme_adv_100hdx_cap=0
set hme:hme_adv_10fdx_cap=1
set hme:hme_adv_10hdx_cap=0
One of these should solve your problem. You need to reboot the system
after putting these entries.
You can also check the port at the OK prompt using the command
"watch-net". This test the onboard ethernet interface.
You may also apply the hme patch released by Sun that fixes many
known problems with hme ethernet driver. The patch id is 108981-03.
It is available from the site :
http://sunsolve.sun.com
HTH
Shridhar
Sun-DTS

Hme0: Link Down - cable problem?

i've a problem i've buyed an ultra 10 (used)
i've reinstalled solaris 10 01/06
when it boot the o.s. it give this error message "hme0: Link Down - cable problem?"
and network don't work.
i cannot ping my router but i've gave to my sun an ip of the same netmask (sun ip 192.168.1.88 router ip 192.168.1.1)
i've checked the cable and it's good (it work with a normal pc)
the led on the switch is on (it's green)
maybe i need some patch
how can i do?

gio,
You didn't necesarily do anything wrong.
You do not necessarily have any broken equipment.
There may just be somthing that is incomplete in the setup.
Begin by checking if your network settings were set up correctly by running:
# ifconfig -a
(it's usually best to troubleshoot while you are root user)
If the output from the ifconfig command seem to be complete, you could always think about reconfiguring the NIC all over again.
If you are not sure, then just paste the entire output results back here.
Also, use the forum search function, using keyword sys-unconfig.
Next, read the Solaris man pages for sys-unconfig.
That command will force you to repeat the setup of the connection.

Howto Link Down-Cable problem?

Hi,
I am having a Ultra Sparc 5 with a hme interface and a quad card. When the machine boots it checks at boot prom level all 5 interface and reports for all qfe interfaces "Link Down-Cable problem?". All qfe interfaces do not have a ethernet connx but I also do not want to deinstall the quad card. Is there any possibility to turn thoose "interface checks" off.
Thanks Marcus

Never mind I just figured out that thoose checks just run after the boot cdrom command.

HT204088 I am receiving unauthorised billings for purchase from application Kingdom Age from seller Funzio, Inc . I can't find a place/link to cancel the billing neither report this problem. The link REPORT A PROBLEM only links you to Apple Store without

I am receiving unauthorised billings for purchase from application Kingdom Age from seller Funzio, Inc . I can't find a place/link to cancel the billing neither report this problem. The link REPORT A PROBLEM only links you to Apple Store without a hint/directions whre you can report the problem.
I've been surfing all parts of the website and didn.t find a manner to REPORT A PROBLEM with purchases on my behalf not authorized.

Hi..
Just to be on the safe side if you have not already changed your Apple ID password, probably should do that.
How to change your Apple ID password
And you can use the email form for contacting Apple here > Apple - Support - iTunes Store - Contact Us

I recive email from itunes to veritify my email adress and is said...''Click link below'' The problem is that i cant see the link plese help me! :)

i recive email from itunes to veritify my email adress and is said...''Click link below'' The problem is that i cant see the link plese help me!

Hi Maastricht2014,
Until and unless you remember the password to your old email address, you will not be able to access the eBooks as those eBooks are only authorized with your old email address only.
The only workaround or alternative to access your eBooks will be to contact the eBook vendor and ask them to migrate the eBook from your old email to the new one.
Hope that Helps!
~ Arpit

Lenovo Thinkpad T60 with start up problems

I have a Lenovo Thinkpad T60 with start up problems. In order to get the computer to start up, I have to unplug it, remove the battery, re-insert the battery and turn it on, once it starts the start up sequence, I can plug in the power cord.
If I plug the cord in before I push the power button, all of the lights go out, and it does nothing.
I have tried several power supplies, and a new battery, even though the old battery seems to work.
All of the updates are applied, including the latest bios update.
The computer seems to work normally unless it goes into standby, then it just turns off.
Any ideas what could be causing this?
T60, 2623 KEU, Windows XP SP3

Hello,
Did you replace the primary battery which snaps into the back, or the internal CMOS/RTC battery inside the unit?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

LENOVO A600-TV, RC related SOUND PROBLEM

There is no problem with my TV function, it is working perfectly. I connect my remote controller to TV, this is also working. After 10 minutes, remote controller(connected with bluetooth) goes into sleep mode because of battery life. when you press any button on RC it goes back to active mode, bluetooth connection is rebuilt again. My problem is about that. When bluetooth connection of my RC is rebuilt again after ten minutes of sleep mode, the sound of my TV goes of. I found two solutions about this problem. First one is not to let RC go into sleep mode by doing anything in that ten minutes which also cause battery of RC last shorter. the second one is from my BLUETOOTH DEVICE's and SERVICE's i make headphones active and after this passive or visa versa. at that moment the sound comes back but this is a lot of work in the middle of TV watching. please HELP ME. if you suggest to setup my drivers again. please send me a link. because i couldn't find a RC driver for lenovo a600. windows 7 64 bit is my operating sys.

Hello,
cannot help with the sound problem.
For memory, I've got almost the same thing but with 4 sticks of 2gb and only 2 detected on an ASUS P7P55D deluxe.
Bios was my issue but I needed to do this (but with pairs of sticks instead of sticks) after the bios update to finally get my 8gb under windows:
Make a clear cmos. Then boot the computer with only one stick of ram in the port .
If everything is fine, turn off and add the other port of the same color for dual channel.
If it does not boot with the 2 sticks in the port of the good color, try to switch ports again. Maybe one stick is dead?

Lenovo Essential G505s (59-380146) Gaming Problem

Hello Lenovo Support
I wanna ask you that this laptop is Gaming laptop but problem is that it not play good game as at low setting I never think that this happen i buy just 2 week ago and very upset with this laptop so if can solve my probelm this will good for me tell me is anything wrong with my laptop or anything i should to do with my laptop.
Please help brother.........

Hi Maskhush,
Welcome to Lenovo Community Forums!
I’m sorry to hear that the Games are not working as expected in your G505s Laptop, I suggest you to check the compatibility of the game and ensure that the latest display driver is installed in the computer. Below is the link to check the compatibility of the game:
Game Compatibility check
Hope to hear back soon
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

LENOVO 3000 N100 "lock-up", "stall" problem

My laptop will start, but stall/freeze at any step after pushing the on buttom. It stalled at "window is starting up", "login in screen", afetr login, during loading the start-up programs or few minutes after running any propgram like Internet Explorer or spybot. When it stalled, the mouse is still able to move arond, but nothing happen if you click an icon. If clicking too many times, it beep two times and the mouse stalled. After a lot of try-and-errors, I think I find out the cause (with 80% confidence). Somehow, I.E. is causing lock-up. I have I.E. 7.0 and Window XP. What shoud I do to fix the problem? I tried to remove I.E. 7.0 from my laptop and re-installed back. It didn't work. Then, I tried to install I.E. 6.0. The set-up says it detected a new version of I.E. installed on my laptop and won't install I.E. 6.0 even I.E. 7.0 is already removed. Thanks for the help.

Try this link: Troubleshooting battery issues - 3000 Family notebooks:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-63099
If that is unhelpful, there is battery troubleshooting info on page 27 of Lenovo 3000 N100 and N200 Hardware Maintenance Manual.
The manual supports Lenovo 3000 N100 (MT 0689 and 0768) Lenovo 3000 N200 (MT 0769)
See this link for the manual
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-63486
Hope this helps!
Thank you
3000 C200 8922-2AU Laptop
Windows XP Pro
T5500(1.66GHz), 1.5GB RAM, 80GB 5400rpm HD, 15in 1024x768 LCD, Intel 950, CDRW/DVD, Intel 802.11abg wireless, Modem, 10/100 Ethernet, IEEE 1394, 6c Li-Ion batt.

Lenovo V 560 major Wifi & Graphics problems!

Hello, i am new here. Last week i bought a Lenovo V 560 Laptop. I have been having problems since then..
The first and biggest problem is the WiFi, i cant get it to work, tried everything and a bunch of drivers. I am no expert but no newbie either. I consider myself a smart dude but i cant beat this!
The system cant find any wifi network and in the system manager i have a yellow dot on the "Network controller" and cant find a driver who works there.
I am running Windows 7 now.
Second problem is that the computer say i have two graphic cards, the Intel HD Graphic and the Invidia M300 graphic card, but the system and the monitor only recognise the VGA Standard screen, and its not possible to switch in Bios...
Anyone good on this stuff here ?
Thanks in advance

hey Roberto36,
i recommend going to this link : http://consumersupport.lenovo.com/us/en/DriversDownloads/drivers_list.aspx?CategoryID=607595
and update all your drivers accordingly.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Lenovo 3000 N200 0769-byg Ethernet problem

Hi, I have a Lenovo 3000 N200 0769-byg with Win-XP SP3 installed There is a problem with the wired Ethernet that is the system doesn't detect the broadcom when it boots after it was shut down Then the system starts to detect it after at least 20min and sometimes more During the detection, the systems goes hang for another 15min After that, I should disable and re-enable the broadcom to make it working the same happens when the systems comes from standby or hibernate To prevent the system of going hang only, i usually disable the broadcom before any shutdown for it i tried reinstalling the xp and installing the latest version from broadcom and no result Any body met the same can help?

press f8 to load safe mode with networking when you see lenovo logo at start-up, then check if issue persists.

Lenovo 3000 N200 0769-K2G webcam problem

Hi All,
I bought this machine a while back with Vista OS. Downgraded to XP and my problems began. Couldn't find webcam driver so went back to Vista Business and still cant seem to work out the issue. In device manager I've got Intel (R) ICH8 Family USB Universal Host Controller 2830, 2831, 2932, 2834, 2835, 2836 and 283A in addition to 7 USB Root Hub (if that info helps).
someone suggested using Yawcam, tried that but no luck. There is no webcam driver on lenovo website which is strange. Please help.
SH

there should be a key to activate the camera. ( fn + something )
check your manual or take a look at the f keys for camera icon.

Lenovo 3000 N200 graphic card memory problem

Hello,
Ive recently bought a new Lenovo 3000 N200, which has a onboard graphic card Intel X3100 with 256MB (shareable) memory.
The problem is, it shows, in the Intel media graphic accelerator driver (under information) it has only 128MB.
This is a copy-paste of the info, the graphic driver shows me:
DirectX* Version:        9.0
Physical Memory:        2038 MB
Minimum Graphics Memory:    8 MB
Maximum Graphics Memory:    128 MB
Graphics Memory in Use:    10 MB
So i would like to know, how can i extend this shareable memory (tried in BIOS, but theres nothing there).
Thanks in advance.

Okay, some of you people are using the Intel GMA 950 integrated graphics rather than the Intel X3100 graphics chipset. The GMA 950 is supposedly to have the maximum shared v ram of 224 mb, but this is only accessable only when the ram is paired and also depends on the motherboard chipsetyou are using. This is also true for the Intel x3100 graphics chipset. However, the catch is that the shared vram is not the bottleneck, you can still play WoW if youwith all the graphics setting to low.

Lenovo ideaphone S920 Link to PC problem

Similar Messages

Maybe you are looking for