Lenovo ix4-300d Russian timezone

Firmware 4.1.106.31982
Incorrectly displays the time:
1) Moscow (gmt+4) - is displayed as gmt+4
2) Minsk (gmt+3) - displayed as gmt+3
Request an update package tzdata and bring web-based interface/led-display according to the updated package tzdata.
Solved!
Go to Solution.

Hello nos96
In regards to the issue you have been experiencing, Europe LenovoEMC Support will need to be contacted to diagnose the root cause of problem and assist with a resolution.
Thank you for posting this issue.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Similar Messages

UPS not recognized by Lenovo IX4-300D

Hi there,
My new IX4-300D is not seening Xfinity Pro Series 2000VA 1200W Uninterruptible Power Supply connected by USB.
QNAP TS-269L on the same subnet has no problem seeing the same Xfinity UPS.
QNAP TS-269L is presently setup as a master. In GUI added IP addresses for QNAP TS-459 Pro II and Lenovo IX4-300D as slaves.
QNAP TS-459 Pro II sees the UPS on QNAP TS-269L, but Lenovo IX4-300D is still unaware of the UPS.
I am using GUI on QNAP and IX4-300D because I am not familiar with Linux and command line.
I can connect to QNAPs using WinSCP.
I have two exactly the same UPSs and would prefer to connect IX4-300D to UPS via USB directly.
If direct connectivity is not possible, I would like IX4-300D to at least recognize that it is a slave.
What can be done about it? Please provide instructions. Your assistance will be greatly appreciated!
Thank you!
Tom

Hello TuToTom
I have been unable to find a specific listing of what USB driver the unit uses, however the user manual lists the usb port as the serial connection. With most UPS devices that list the usb port as a serial power it usually means that the unit uses a usb to serial (rs232) adapter internally.
The Lifeline NAS devices support USBHID-UPS enabled UPS devices. Most APC models, dell, and eaton units can or do use this driver. This would be different than the usb connected serial link method.
I recommend contacting the ups manufacturer to confirm how the usb port on your ups unit functions and proceed from there.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Lenovo ix4-300d free space left

Hello, I have an Lenovo ix4-300d, 8TB. My free space on the servers tells me that there is left 3.8TB, when I look in my Share there is almost no space left. What can I do to get more space in my shares? Now I receive the following message: The amount of free space on your Lenovo ix4-300d is below 10% of your total capacity. And that should not be the case!? What can I do? Thanks for a reaction, PPU
PPU

I am sorry but I am not sure what you are referring to by MIB, are you trying yo use Management Information base to monitor free space? Can you please explain more what you are trying to do?
You can manage the free space through LenovoEMC storage manager and we UI. You can even set it up to email you when you are running out of free space.

Lenovo ix4-300d - Data protection is being reconstructed gets stuck.

Hi experts,
After a power loss my Lenovo IX4-300d went on a "Data protection is being reconstructed" phase. This process never ends because it gets stuck at a certain % that changes every time I power on the IX4, at this point it becomes unresponsive and I have to unplug the power cord. I´m using RAID 5, so theoretically there is more than one drive failing. I am not an expert of course, just googled this, I don´t even know if its right.
In the other hand there is nothing stating a HD failure in the logs or the system status of the IX4.
So, how can I identify which drivers are failing in order to replace them?
Could this be a logical failure and be fixed by formatting the drives?
Any additional comments or recommendation? I am able to access my data while it´s "reconstructing" so I am moving my things out of the nas.
Thanks
EG

You can try rebooting with one drive removed at a time. If you are having one drive fail you should be able to boot with it missing. You should also check to see if you are still in warranty and call tech support. They will be able to assist in diagnosing the issue and replacing drives if needed.
Contactos — Latinoamérica

Lenovo ix4-300d and 4 Hd 6 tb red

Hi first of all sorry for my english,
I have 4 Nas ix4-300d,
3 with 4 green 3 tb Hd they work perfectly never have any problem in 3 year. I work in raid 0 because
I duplicate the files in other HH and I want the maximum of space available.
the fourt one I bought 3 days ago and I try to install 4 6Tb red wd inside it in Raid0 here is the problem...
I can't create shares becouse of this message :
"The selected function is not available due to the state of the pools"
So I look on the internet and see that maybe I can't work in raid0 if the disk is bigger than 4 TB (CRAP)
then I try to put Raid 5 ( the only I can choose beside Raid 10 ) but in 36 Hours the data recostruction
is only 19 % with 0 files on it.......................
Can someone Help me please?
Can someone give me some advise?
Did you know a Nas that work in Raid0 with 6tb and 8 tb disk?
Ty in advance.

Hello Nico84
1. The ix4-300d will probably be able to use 6 TB HDD's if only 2-3 were installed and depending on the protection mode( 2x 6TB disks RAID 0, 3x 6TB disks RAID 5). However the limitation your are running into is that the the ix4-300d's Marvell Armada XP 1.3GHz MV78230 processor is only 32 bit and has the 16 TB ceiling.
2. The ix2-dl and px class devices can officially support 6TB HDD's in RAID 0 or NONE.
3. Please check with these retailers/resellers about lenovoEMC devices in your region. Where to Buy
4. With any 32 bit system the capacity limit for a volume is 16 TB. With the ix4-300d the max supported is 4x 5TB disks in RAID 5, this would roughly yield a 15 TB volume.
What you are attempting with the 4x 6TB HDD's in RAID 5 would roughly yield a 18 TB volume, which is above the 16 TB volume ceiliing for the unit's processor.
Again using 3x 6TB HDD's should theoretically work in RAID 5 and yield about a 12TB volume. If you were to use just 2x 6TB HDD you should theoretically be able to have a 12TB RAID 0 array. Both of which would be under the 16 TB cap.
If you are fully intending on using 4x 6TB or larger disks, then a px class unit will need to be used.
I hope this better explains the situation you are having.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

I need confirmation, please help me! (about adding new hdd on my ix4-300d)

Hello,
I buy recently a Lenovo ix4-300d, I have installed one hdd seagate 2To (ST2000VN000).
I saved many documents on it..
Today I want to install 2 others hdd WD 1To (WD10EZEX).
After reboot a message tells me I need to erase all data on the news disks before I can use it, so I confirm, all seems ok.. After that a message appear on the left "2 disks unused".
Now (step 3 page74 on the .pdf guide) I need to check the box "add drives to storage system" and click confirm to activate the news disks, so I do, but I have this message:
"Vous devez supprimer les données existantes pour pouvoir modifier la configuration du disque.
Cochez cette case pour continuer."
(in english "You must erase existing data for change the disk configuration" or something like that)
I don't want to loose all the data on my first hdd already in use.. ..and the 2 others news disks are empty.
So, there is my question:
if I check the box and click continue what "existing data" will be erase??
existing data on all hdd?? Or just on the new one??
nb: Sorry for "my english" but there is no french section in the forum, and the assistance don't answer me by email, and on the phone there is an answerphone tells me "for help if you don't have the error number code, you must go on the forum, bye.." .. .. I hope my question is understandable.
Thanks

Hello tictictac
Sorry that you experienced data loss, however it was preventable if a backup had been made as recommended.
From the screen shot you sent it looks like the drives were already added to the existing array after the first drive overwrite request. With the array being made up of mixed disk models and none of the disks showing any green stipes indicating overwrite selection, I can not say for certain what caused all the disks to be wiped. I suspect that is was taken as a RAID change and all disks were wiped from there.
For future reference please check the device support page to see the guides, FAQ's, and download the full user manual( in French here ) and check with LenovoEMC support in your region. The Europe support region has several languages available to choose from including the France number +33 17048 0388. The full list of Europe numbers can be found here.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

File system error on IX4-300d

Hi all. I got message "File system error. You must perform file system check". How can I do it?
Sorry for my English.

Hi. Can you tell me how to run fsck command. I have the same problem with the drive and I get the same error :
"The file system on your Lenovo ix4-300d has errors and needs to be checked".
I have 2 Hard disks both of 3 TB in simple configuration. The suggestion of file system check did not work. I tried your method of SSH into the hard disk. However I cannot complete the process as I got the following error:
root@DataVault:/# fsck -y /dev/sdb2
fsck 1.42.5 (29-Jul-2012)
e2fsck 1.42.5 (29-Jul-2012)
/dev/sdb2 is in use.
e2fsck: Cannot continue, aborting.
This is consistent with sdb1, sda1 & sda2
Also I have provided the parted -l info below:
root@DataVault:/# parted -l
Model: ATA ST3000DM001-1CH1 (scsi)
Disk /dev/sda: 3001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start   End     Size    File system Name     Flags
1      33.6MB 21.5GB 21.5GB               primary
2      21.5GB 3001GB 2979GB               primary
Model: ATA ST3000DM001-9YN1 (scsi)
Disk /dev/sdb: 3001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start   End     Size    File system Name     Flags
1      33.6MB 21.5GB 21.5GB               primary
2      21.5GB 3001GB 2979GB               primary
Model: SanDisk Cruzer (scsi)
Disk /dev/sdc: 16.0GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start   End     Size    Type     File system Flags
1      16.4kB 16.0GB 16.0GB primary fat32        lba
Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/9aee462_vg-lv3a09ce04: 5958GB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Number Start End     Size    File system Flags
1      0.00B 5958GB 5958GB ext3
Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/md0_vg-vol1: 17.2GB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Number Start End     Size    File system Flags
1      0.00B 17.2GB 17.2GB ext3
Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/md0_vg-BFDlv: 4295MB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Number Start End     Size    File system Flags
1      0.00B 4295MB 4295MB ext2
Error: /dev/mtdblock0: unrecognised disk label
Error: /dev/mtdblock1: unrecognised disk label
Error: /dev/mtdblock2: unrecognised disk label
Error: /dev/mtdblock3: unrecognised disk label
Error: /dev/mtdblock4: unrecognised disk label
Error: /dev/mtdblock5: unrecognised disk label
Error: /dev/mtdblock6: unrecognised disk label
Error: /dev/md0: unrecognised disk label
Error: /dev/md1: unrecognised disk label
root@DataVault:/#
Any help would be greatly appreciated.
Thanks in advance

Ix4-300D as iSCSI target cause alert disk is full

I am using ix4-300D with RAID5 as iSCSI target.
Once I create largest volume using all capacity, ix4-300D sends warning disk is full. Because we monitor this iSCSI target using E-mail alert, I want to eliminate this warning message. There is no configuration point on Web management GUI.
I guess other people using this unit as iSCSI target have same concern. If you know something, please help me about this. Thanks in advance.
Alert message:
The amount of free space on your Lenovo ix4-300d is below 10% of your total capacity.

Thank you for your reply.
I gave up to use 11% of diskspace as iSCSI target of VMware ESXi because catching alert message is more important for production environment. I hoped interface to disable some type of alerts.
I am not sure about using remained 11% space for NFS NAS or something. It is because iSCSI Target volume will contain VM Guest OS volumes which require very stable operation.

Probleme d'identification ix4 300d

bonjour Je viens d'acquerir un nas lenovo ix4 300d mais lors de l'installation le systeme m'indique qu'il est indisponible or j'ai bien installe le logiciel , l'icone apparait sur mon pc . La connection a ete verifiee,comment resoudre ce probleme merci

I just acquire a nas lenovo ix4 300d but when installing the system tells me it is unavailable or I have installed the software, the icon appears on my pc. The connection was verified,
how to solve this problem thanks

IX4-300D Lenovo NAS - faceplate

Just recieved a brand new IX4-300D Lenovo NAS LCU-101759656 but faceplate clips damaged in shipping. Is it possible to get a replacement faceplate?

Hi Debonator,
Where did you purchase your new device from? We typically do not replace specific parts like the front faceplate and would replace the entire device under the warranty if the device is damaged, but the replacement device will be a refurbished unit. I would recommend contacting the reseller that you purchased the device from first to see if they can replace the unit for you brand new.
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Lenovo Iomega ix4-300d Disk Firmware Upgrade

Hi guys,
Is there a any way to upgrade my Seagate ST2000DM001-9YN164 Firmware from the IX4-300D device?
The Seagate have a firmware upgrade utility, but is a livecd and it is for i686 hardware.
Solved!
Go to Solution.

We do not recommend or see it necessary to update the firmware unless you have firmware CC37 or lower. Is there a particular reason you wanted to upgrade the firmware? These drives should work with our device without needing to update the firmware.
If you want to upgrade the firmware, then you will have to do so manually by taking the hard drives out individually and connecting them to your computer. Seagate has a program called SeaTools (http://www.seagate.com/support/downloads/seatools/) that you should be able to update the firmware with. However, be advised that if you are in warranty and perform the update and the device is damaged, it will void your warranty.
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Problem active directory importing users at ix4-300d sw ver 4.1.108.32627

Installed new ix4-300d onto network, added to SBS 2008 domain and can log into NAS with domain\administrator account . In users & groups can see domain\administrator account along with local admin account. Click on sync with AD, no errors, but never get any users in the list
Whats the problem ? I need to get users from AD imported to get shares working.
Please help as customer is not happy.
regards
Peter

Hello blue256
If you entered a Organisational Unit in the Domain Management page, please try clearing the OU field and try re-adding the unit to the domain.
After that is done, please try checking if the domain user and groups are accessible from User and Groups page.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

How do I disable administrator username and password entry to access ix4-300d

With the recent version 4.1.102.29716 update, I am now FORCED to enter a username and password to get into my "home based" ix4-300d NAS. This has already been a MAJOR pain for my nedia server setup, in that I am no longer able to create a network drive to one of several NAS folders on to my home network.
My question therefore is, how do I DISABLE the function of having to enter an administrator username and password to gain entry into my ix4-300d?
Thanks,
Bill

No hazzle, just do it.
This is only for admin purposes. You are still able to place your media into individual user shares or put it in the public area where they will be accessible for everyone, even if you set 'security' on.
Various PCs / Laptops ( sorry I still really love Dell and Fujitsu ;-))
Supporting Customers ix2s and ix4s -- Love Networking ( not only technically ).
I am not a Lenovo Employee.
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

IX4-300d - UPS, not showing in management, but sends messages if I connect and disconnect

Just acquired a iX4-300d, and updated to the latest firmware (4.1.104.31360).
On trying to link a UPS (a KSTAR BM-3080) - the UPS Management page just shows "Status: None Connected"
BUT - in the EVENT LOGS panes I get the following message:
Event
4462 An Uninterruptible Power Supply (UPS) has been recognized.
and if I unplug the USB connector between the UPS and the iX4-300d - the message
Event
4463
The Uninterruptible Power Supply (UPS) has been removed.
is shown ----- Surely if it sees a UPS is connected it should show one in the UPS Managment page, of not then why does it show in the Event log console.
ALSO:
Given that the iX4-300d seems to recognise a UPS has been connected - is there some way to update/replace or even get to the code related to this UPS mmanagement section, so I can get readings from the UPS, thus enabling a 'smart shutdown' when the battery drops to say 10% remaining?
(Could it not be just a "Plug in" that allows smarter people than me to enter the UPS I/O values and make it work with a wider range of UPS devices.
Additionally - so far I havn't seen a list of "Approved UPS", just a note about some UPS systems that do not work.)
DG.

I've tested this with an ix4-300d and APC smartUPS 1500 ( which is not on the list of compatible UPS ), but it is working exactly as you wish. Somewhere around 15% battery the device will shut down.
Give it a try....
B.T.W You may test the notification functionality by unplugging ups main supply. If properly configured this event will shouw up in the log and NAS will sent notification mail ( + another mail when mains are recovered)
Various PCs / Laptops ( sorry I still really love Dell and Fujitsu ;-))
Supporting Customers ix2s and ix4s -- Love Networking ( not only technically ).
I am not a Lenovo Employee.
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

What is the proceedure for replacing a hard drive (after failure) for RAID 5 with IX4-300D?

I have the IX4-300D with 4 hard drives (identical Seagate drives) using RAID 5.
Someday a hard drive will fail and I and I have to replace it. I read through the users manual briefly and I didn't see any documentation on how to perform a hard drive replacement and not lose any data.
So here are my questions:
1) I know per the instructions that Lenovo prefers using identical hard drives. Let's say in 2 years, 1 hard drive fails. Most likely, the same model Seagate hard drive will not be available. So will using a replacement hard drive by the same manufacturer with similar specifications work?
2) Will the front panel (or the software) tell me which hard drive has failed?
3) What is the proceedure for replacing a hard drive after a failure occurs? I read that the IX4-300D is not hot-swappable. So do I just power the IX4-300D down, replace the hard drive, and turn it back on?
Solved!
Go to Solution.

Hi exceptionalht,
It is best to replace the hard drive with one that is the same manufacturer, rotational speed, and capacity, so it does not have to be exactly the same model.
The front panel should show which drive has failed. If not you can check the web interface to find out.
That is the basic procedure for replacing a hard drive. You can see a more detailed instructions here: Installing hard drives in an ix4-300d
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Lenovo ix4-300d Russian timezone

Similar Messages

Maybe you are looking for