Lenovo Miix 2 10 internal USB points

Does anybody know how to find internal USB points on the mainboard? Would be nice to find it out, and it make possible to embed any device like additional sd card reader or even LTE modem - there quite enough room inside of tablet.

are you're sure that nothing is coming out of your dock-speakers when tablet is connected in presentation mode?
This was also my first impression but with my device it is indeed working. The quality and volume is VERY disappointing, tablet speakers are louder than the dock-soundbar-speakers. Those speakers don't deserves the name soundbar
Please check again and keep shut the tablet speakers with your hand. And open you ears in front of the soundbar
I also hope there will be a software/driver fix provided in the future to fix/improve this. Annoying.
Regards,
Bernd

Similar Messages

Lenovo miix 2 10 windows 8.1 key

Dear Lenovo support Forum,
I have a Lenovo Miix 2 10"1 without keyboard, 64Gb version with office 2013 home and student license.
On my disk had 16Gb space after my programs installed.
So I tried to save the whole drive to my nas bit-to bit but I could't boot to a linux while i swithced off the secure boot.
I made a new windows 8.1 core installer prepared to Wimboot.
I Installed to the internal drive everything and after the office-updates-drivers-softwares-email-backups i have now 40Gb free space, the CPU freq now on IDLE is under 1Ghz ( better for battery) and i have more RAM.
Now I have a really big problem: I forgot to write down my original Windows 8.1 core key. How can i get it back?
I downloaded a read-write everything software ( x86) but I cannot find a same MSDN?? field at ACPI so I could not get the windows 8.1 key from the BIOS.
Is there any way to get is back? I have all of the SN noumber, etc so how?
Or from this point I have to buy a new operation system?

lythala wrote:
I tried to drop that line to a CMD as administrator but no response, about 20 seconds i got the shell back
Tried to start the powershell and copy that line but after 2 minutes I stopped that.
You can download RWEverything utility from http://rweverything.com/ run it, select table ACPI, then tab MSDM and you can see the key. That command line command works on my miix2, I can't say why not on your computer.

Lenovo Miix 2 8 inch HDMI Adapter?

I want to display my Lenovo Miix 2 on TV equipped with an HDMI input. I don't believe the Miix 2 is MHL compatible. Is there an adapter to connect the Miix 2 micro-USB port to HDMI?

Dear TonyBLenovoUser
Welcome to Lenovo forums
to connect this machine to an external monitor you will need a connector like the one in the below image
Try and let me know
Thanks
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Support warranty Lenovo Miix 2 10" Touchscreen failure

Dear Lenovo Support!I have purchased 01 Lenovo Miix 2 form Amazon with S/N: QB08221114Now, the Touchscreen will stop respondingIn Control Panel, Device Manager show: I2C HID Device with note Yellow (picture att)I checked it in the device manager: Touchscreen is not listed under HID-Devices and the I2C HID-Device got an error I had try worked all help in topic: https://forums.lenovo.com/t5/Windows-based-Tablets/Re-Miix-2-Touchscreen-failure/td-p/1441509, it's not workingMy Lenovo Miix 2 is using in Vietnam, I had call Lenovo in Vietnam, not support Lenovo Miix 2 10". I want to Lenovo help me support warranty Miix 2. Best Regard Khanh Trinh

Hi
I have a same problem
For me it s not a touchad with this simple feature...
Is not possible to install Synaptics Drivers (standard touchpad...)...
It s a simple mouse device
It s a strange technical choice, but we have a tactil screen for that... (stupid monkey engineer)
Aida64 says; Mouse HID
Field Value
Mouse Properties
Mouse Name Souris HID
Mouse Buttons 2
Mouse Hand Right
Pointer Speed 1
Double-Click Time 500 msec
X/Y Threshold 6 / 10
Wheel Scroll Lines 3
Mouse Features
Active Window Tracking Disabled
ClickLock Disabled
Hide Pointer While Typing Enabled
Mouse Wheel Not Present
Move Pointer To Default Button Disabled
Pointer Trails Disabled
Sonar Disabled

Miix 3-1030 no usb boot at all, not even with an otg cable

hi lenvovo i'm liking my new miix 3-1030 tablet i purchesed recently but have found the bios to be frankly useless.the tablet has no usb booting at all, nothing shows up in the boot menu except windows boot mangager.i've tried the following; usb hdd'susb sticksotg cableusb dvdrw none show up for booting, this is annoying as i use virtual machines and boot other os's from eithe live cds or usb devices. any chance of a bios update that enables usb booting? i don't want any other options, just the simple ability to boot other devices.

I'm experiencing the same thing with my Miix 2 8. See https://forums.lenovo.com/t5/Windows-based-Tablets/Miix-2-8-no-USB-flash-drive-recognized-with-quot-Device/td-p/2132514 I would like to remove my recovery partition to free up space and then upgrade to Windows 10, but can only do so when I can boot from USB. So far I've been unsuccessful. --Ron

Apple USB keyboard does not work with one internal usb port

Hi everyone,
hope someone can help me to solve my problem. I have a MPB13 retina late 2013 since something like 3 months. I have additional screen (dell), usb wired keyboard (apple) and BT magic mouse.
Since a few days, my usb keyboard does not work well. It only want to work properly when plugged to the rights side usb port internal port and not anymore on the left one. It also work on a usb external concentrator. Before, I had no problem, it worked perfectly. There was no problem such as cofee on it...
After searching the web on such problem, I tries a few things such as:
I tried the keyboard on another computer (windows): works fine
I tried usb stick and external DVD reading on the left internal usb ports: works fine
I switch the MPB off and turn it back on: the usb keyboard still does not work on the left usb port
I tried the SMC and PRAM reset : nothing
Any idea ??
Thanks
Guillaume

I'm facing the same problem, found any solutions ?

Unresponsive keyboard/trackpad and intermittent Bluetooth on MacBook...possible internal USB problem?

I have a mid-2010 polycarbonate/white MacBook (model A1342) running OS X 10.6.8. My machine has been having issues with the internal Bluetooth and keyboard/trackpad randomly ceasing to function.
Bluetooth issue
As of recently (the past month or two), the Bluetooth adapter will completely disappear and eventually reappear on a random basis. It won't appear at all in System Profiler, and the BT menu says "not available". Also, I have had a few kernel panics recently, all of which were apparently thrown by a Bluetooth process/daemon/driver (unfortunately I forgot which one, and also lost the logs from the panics.)
My system has a Broadcom Bluetooth chip that's part of the AirPort card, but is basically just an internal USB device. The adapter has some sort of integrated USB hub ("BRCM2070 Hub"), which the "Bluetooth Module" device itself is connected to.
Nonetheless, this seems to be some sort of problem on the USB bus. Whenever there is a failure, I will almost always see output in Console showing USB errors (ie errors about "enumerating a USB device", "clearing port power", "setting port power", "getting port status", etc). It will either be on any of the ports of the hub at 0x6600000 (the "BRCM2070 Hub" that "Bluetooth Module" is connected to), or port 6 of the hub at 0x6000000 (BRCM2070's port on the internal bus, which the keyboard/trackpad is also connected to on port 3).
I can post more/longer ones, but here's a somewhat short example of the error messages I might receive:
11/18/12 3:18:36 PM kernel USBF: 7351.492 [0xcf9b300] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 6 of Hub at 0x6000000)
11/18/12 3:18:38 PM kernel USBF: 7353.987 AppleUSBHubPort[0xcf9b300]::FatalError - Port 6 of Hub at 0x6000000 reported error 0xe00002c7 while doing clearing port power feature
11/18/12 3:18:38 PM kernel USBF: 7353.987 [0xcf9b300] The IOUSBFamily was not able to enumerate a device.
11/18/12 3:20:20 PM blued[448] Apple Bluetooth daemon started
11/18/12 3:20:20 PM kernel USBF: 7456.186 [0x11fb1300] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 2 of Hub at 0x6600000)
11/18/12 3:20:20 PM kernel USBF: 7456.188 [0x11fb1300] The IOUSBFamily was not able to enumerate a device.
Keyboard/trackpad issue
There's also an issue where the internal keyboard/trackpad will randomly cease functioning (until I restart), often a couple of times a day as of recently. I've had this issue on rare occasion for a while now, but it's gotten more frequent. And more recently, the caps lock light on the keyboard occasionally turns itself on when I'm away.
Both the internal keyboard/trackpad as well as the Bluetooth "hub"/device are connected to the same USB bus/hub. When the keyboard/trackpad die, I've noticed that there will be very similar messages in Console to those above and usually a Bluetooth failure at the same time. (In some cases, it seems to notice that the keyboard/trackpad isn't responding, then attempts to reset/reinitialize it...ie log below.) What could the root cause be...could it be the USB "root" hub/bus causing one or both of these to fail, or possibly a problematic device causing the other to lose connection? I haven't had issues with USB devices on other buses failing, though (ie no problems with external devices.)
Maybe more out of curiosity than anything else, but I've been poking around for info on what might be going on with the USB (aside from the 0x66 hub repeatedly dropping/reconnecting and etc), but can't find much. There seems to be no documentation about the error codes (ie 0xe00002c7) that the hardware/OS are relaying. I even poked through the source for some of the relevant kexts and some reading on OS X driver/kernel programming too...might as well learn more about the inner workings of OS X
Here's an example of some of the messages that I get about the Keyboard/Trackpad:
11/21/12 2:57:22 AM kernel USBF: 1439.228 IOUSBHIDDriver(AppleUSBMultitouchDriver)[0xd1ff000]: Detected an kIONotResponding error but still connected. Resetting port
11/21/12 2:57:22 AM kernel USBF: 1439.234 AppleUSBHubPort[0xd040600]::Resetting device Apple Internal Keyboard / Trackpad: port 3 of Hub at 0x6000000
11/21/12 2:57:22 AM kernel USBF: 1439.319 [0x14452600] USB HID Interface #0 of device CompositeDevice @ 5 (0x6610000)
11/21/12 2:57:22 AM kernel AppleUSBMultitouchDriver::message - kIOUSBMessagePortHasBeenReset.
11/21/12 2:57:23 AM blued[248] Apple Bluetooth daemon started
11/21/12 2:57:23 AM kernel AppleUSBMultitouchDriver::checkStatus - received Status Packet, Payload 2: device was reinitialized
Attempted fixes
Unfortunately, my Macbook isn't under warranty so I'm mostly on my own. First I zapped PRAM, reset SMC, ensured OS updates are installed (still on 10.6.8), and threw out a few drivers/software that were possible troublemakers. Next, I tried running another OS/install to rule out software issues. Accordingly, I found that the BT adapter sometimes disappears on Windows 7 as well (just did a clean install). And finally, I bought a new AirPort/BT card and installed it the other day. That seemed better at first, but I still have the problem of intermittent Bluetooth and keyboard/trackpad.
Problems/solutions?
What might the issue be, or is there anything that may be worth trying? As I mentioned, I've reset PRAM and SMC, made sure it's not an OS/driver issue (it happens on Win7 too), and replaced the Airport card. The machine does have aftermarket RAM (from OWC, ~2 years old) and SSD (Crucial M4, installed September)...but it seems unlikely that either of these would cause the problem. There haven't been any accidents that would have caused physical or (to my knowledge) electrical damage to it.
I also searched for any occurrences of similar problems, but could not find any that were applicable to the Macbook revision in question. There was a similar keyboard/trackpad issue on older Macbook Pros that was caused by stress on a ribbon cable...but that seems unlikely given the concurrent issues with Bluetooth as well as the different design.
The only thing I can think of next is to possibly replace the cable connecting the Airport card to the logic board, and possibly look at replacing the keyboard/trackpad (topcase). Anyway, I'm worried that it might be a hardware issue with the internal USB controller/hub, which would probably mean that it's unfixable unless I replace the logic board.
Any advice as to which of these might be a potential solution or cause of the problem? Or might I just as well sell it off in its current condition and replace it?
Thanks all!

Has anyone find a fix for this? I've been using my Dragon Dictate headset on my MacBook Pro for about a year, and then today, when I plugged it in, I got this:
4/16/14 10:01:04.000 AM kernel[0]: USBF:    47.766    The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 1 of Hub at 0x4000000)
4/16/14 10:01:07.000 AM kernel[0]: USBF:    50.269    AppleUSBHubPort::FatalError - Port 1 of Hub at 0x4000000 reported error 0xe00002c7 while doing clearing port power feature
4/16/14 10:01:07.000 AM kernel[0]: USBF:    50.269    The IOUSBFamily was not able to enumerate a device.
Here is what I have tried so far:
Reset the PRAM
Reset SMC
Verify disk (there were no problems)
Repair permissions
Boot with an external USB hard drive (which works fine on the "problem" computer) that contained an old SuperDuper clone of my hard drive from several months ago. I received the same "The IOUSBFamily was not able to enumerate a device" error when I plug in the headset.
Tried to headset on another computer, and it worked fine.
Plug in an external USB keyboard into the problem computer, and it works fine.
All of this would lead me to conclude that it is a hardware problem. But it seems that if it were a hardware problem, the external USB keyboard and external USB hard drive would not work (which they do). If the problem were with the headset, it wouldn't work on another computer, but it does. So I'm wondering if it's some sort of firmware issue…??????? URG!!!!!!

MacBook Pro (mid-2010) Internal USB HUB freezes/locks up

MacBook Pro (mid-2010) wilth the latest firmware, etc.
OS X 10.9.1
USB KVM to share keyboard and mouse with another computer
This has been working flawlessly until I upgraded to 10.9.1
The KVM uses the Scroll Lock key to toggle the input between the two computers
I switch back and forth many times a day.
Almost once a day now, all my input to my MBP will lock up when switching the KVM over.
The MBP track pad, keyboard, blue tooth Magic Mouse, KVM mouse and keyboard all become unresponsive.
I am assuming that the interal keyboard/track pad/blue tooth transceiver are all tied to an internal USB HUB.
The MBP is up and running and I can ssh into it. The only error message in the log is that the mouse device coming from the KVM is busy and it will be disabled. I have tried to close the lid for several minutes and then re-open, but it does not resolve the issue. I have tried connecting another USB mouse/keyboard during this time and it will not work. I have tried kill -HUP on the usbd and USBAgent processes. Everything stays unresponsive. The only way to resolve this condition is to reboot the MBP. Note: the KVM works find on the other computer when I switch it back and forth regardless of the state of the MBP.
I am suspecting that when this happens it is some how disabling the internal USB HUB, which if all the other devices are connected through it, nothing no longer works (but maybe I am crazy with that thought). Anyone have any insight? Is there a way to reset the internal HUB short of a reboot?
Thanks in advance!

I'm seeing the same problem with a 2010 Mac Mini with IOGear KVM and MS wireless mouse. This setup worked flawlessly for years on Snow Leopard but started hanging soon after the Mavericks upgrade. I'm running 10.9.4, currently the latest release. The system usually hangs after a KVM keyboard switch from Windows on the other set of KVM cables back to the Mac Mini. ssh into OSX works fine but a shutdown hangs indefinitely. top showed no processes spinning. The 1st console message after the hang was:
8/6/14 8:49:21.000 PM kernel[0] USBF: 1317978.201 AppleUSBHubPort: Port 2 of Hub at 0x6200000 about to terminate a busy device (Microsoft® 2.4GHz Transceiver v7.0) after waiting 10 seconds
There were no other messages for hours before this. I'm using VM Fusion but I think it hung once without it running. The Windows 7 side of the KVM works fine.

HT203175 My iPod touch is off and I can't turn it on because when I try, it has the iTunes logo and a usb pointing to it...and when I connect it to my computer and try to open it to iTunes, it says I have to restore it, but I don't want to lose all my pic

My iPod touch is off and wont turn on because it has the itunes logo and a usb pointing to it, so when i looked it up online, it says i have to restore it but i don't want to because i don't want to lose all my pictures. What can I do?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Lenovo Miix 2 8 Control panel freezes

Santa recently brought me a fresh Lenovo Miix 2 8 (64 GB). It's been just fine until I realized I can't execute windows update at all. When I go to control panel and try to access windows update, it changes the topic in the control panel window, but doesn't open any windows update settings. The control panel window then freezes and cannot be closed in any way, can't be moved either. The same thing happens when I try to access language settings in control panel. So basically I can't update windows nor tweak language settings, because the window freezes if I try to do so. When I try to access windows update via the new win 8 UI, it won't freeze or crash as far as I remember, but just won't load anything.
Help me out please! I'm not sure if it's lenovo or windows that's to blame but I don't think I'm keeping the device if this can't be fixed. Couldn't find others having similar problems either. This problem occurred basically straight out of the box, which is strange.

Hi,
I had the same error.
After i deinstall the latest drivers (comes with Windows-Update) of 'Intel(R) Imaging Signal Processor 2400' the camera works fine.
You can deinstall the latest drivers in the DeviceManager under ImagingDevice (known so in english?), then properties for driver and 'install previous driver'.
Please tell us when it works again.
Thanks and sorry for my bad english
Matt

My ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else. It won't switch on beyond that. Please help!

my ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else. It won't switch on beyond that. Please help!

Sounds like your iPod is in restore mode. Connect it to iTunes. iTunes will pop a little message up saying that your iPod is in restore mode and asking you if you want to restore it, click yes. Your iPod will restore to factory settings and you will be given the chance to restore from a backup. You can do this or set it up as a new iPod.
Here is Apple's page on restoring your iPod.
http://support.apple.com/kb/ht1414
Hope that helps.

Is iSight using internal USB BUS in Bootcamp (win xp ) mode?

Hello,
I am having issues with my musicall instrument that is plugged into Mac Book Pro 15" 2.0 Core Duo 1G RAM. The instrument is plugged into one of the USB port of MBP.
I would like to know if iSight in WinXP mode is using internal USB bus.
If it is, how can I disable it? Using device manager in Win xp?
Thanks in advance,
MT

Same problem here exactly. I can't do anything with this stupid message box because both mouse and keyboard are not responsive.
It used to work in the past, it probably stopped working after upgrading to Snow Leopard. Please, someone come up with a workaround !

Lenovo Miix 10 Built-In Case Keyboard is not working

Hello,
I am having problem with my case keyboard which is not working. I bought my Lenovo Miix 10 3 days ago but the Keyboard (the built-in Case Keyboard) has never worked. Does anyone have a solution on how to turn it on/fix it?
Thank you for your help
Moshe

Hi
Welcome To Lenovo Community
We are really sorry to hear about the issue you are facing,
Based on what I read from the post, it seems to be a hardware issue with the keyboard
Please contact Local Lenovo support to have system verified
http://support.lenovo.com/en_IN/feedback/detail.page?LegacyDocID=MIGR-76613
Do give this a try and let us know
Hope This Helps
Cheers!!!
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community Deutsche Community Comunidad en Español

SATA, Internal USB, Firewire

I want to get an internal card reader for my sandisk extreme III CF. I was looking and found some that hook up internally via USB. Does the Mac Pro have any of these internal hookups, other than the SATA used for optical drive 1 and the 4 HD's, or the usb used for BT?
So,
-Internal USB? (are these possibly called headers)
-Internal FireWire?
-Extra SATA Ports?
Also I am looking into some kind of PCI card that would give me mic-level inputs, and preferably support 5.1 sound. I just want to confirm that only a "PCI-E" card fits and nothing else, right? Also what's the major difference between a 5.1 soundcard that costs 30$ and a 5.1 that costs 130$?

in your search you best include deep sleep compatible. when you find one let us all know.

Lenovo Miix 2 8 brightness

I bought a miix 2 8 inch the last week, i really like it.
There is something strange about the brightness level.
It seems that using the windows slide bar, it reach the maximum level at 50% of the bar.
From the 50% to the 100% of the bar it doesn't change the real brightness of the device.
Thanks
Solved!
Go to Solution.

I do have the same problem here. How can I increase its brightness? We have to the same lenovo miix 2 11 tablets at home. The one 's screen brightness is not high enough even if it reaches the maximum in the bar (manually doing it). Thank you

Lenovo Miix 2 10 internal USB points

Similar Messages

Maybe you are looking for