Lenovo Notebook Yoga 2-13 Nach Clean Installation von Win 10 keine WIFI Verbindung

Nach Clean Installation keine WIFI Verbindung Nimmt das Netzwerkkennwort nicht an, ist aber es richtig
Habe soweit alle neuen Treiber für Win 10 installiert. Im Gerätemanager ist noch eine Meldung offen, unbekanntes Gerät. Was könnte das sein
Hat jemand einen Tipp
Danke
Helifax 

Kleiner Nachtrag zu meinem Post oben: Bei weiterem Gestöbere im Internet habe ich heute herausgefunden, dass es eventuell doch einen Unterschied macht, welche Geräte im Standby aktiv sind: Wenn WLAN/LTE und GPS deaktiviert sind, scheint das Yoga-2 im Standby (zumindest bei aktuell 95% Akkustand) *nicht* abzustürzen und ist durch kurzen Druck auf die Powertaste und mit laufenden Programmen einfach wieder aufzuwecken. Kurz zuvor war es mir bei Akkuständen zwischen 98 und 96%, aktiviertem WLAN (und deaktiviertem LTE+GPS) mehrfach abgestürzt.

Similar Messages

  • Benötige nach neu installation von win 7 software download für photoshop 8

    benötige nach neu installation von win 7 software download für photoshop 8

    Hi there,
        Download for Elements 8 is also available in the above link which Mylenium has provided. If you are unable to locate, then here is the page I have located it for you..:)
    http://prodesigntools.com/direct-download-links-for-lightroom-3-and-photoshop-elements-8.h tml
    Read the instructions very carefully before starting the download, else you will face an error..
    Once you download the product, you can use the serial number to activate it into the full version. Please take a back-up of the media for future use.
    Regards,
    Jairaj

  • Lenovo System Update creating problems in fresh installation of Win 7

    I'm hoping I can get help from this forum...
    I have a Thinkpad R61 7742-CTO that has its original XP Pro operating system in day-to-day use.  It's time to finally update to Win 7 with XP due to sunset soon. (Although I think Win 7 is visually ugly compared to XP)
    I removed my "production" XP disk drive and did a clean installation of Win 7 Pro on the original purchase ("test") disk, including the 140-some MS updates available as of yesterday.  Everything runs fine, including using Windows Update to search for new important and optional updates.  So far, so good.  I next went to Lenovo's website and downloaded the current version of Lenovo's System Update.  Again, no problems once that particular program was installed.  I installed Lenovo optional updates also without encountering problems.
    However, when I load the Lenovo important updates, which include Access Manager, Power Mgr, etc., various intel and other "enhancements", things go wrong.  If I click on Windows Update, for example, I get a message that it is not running.  If I then do the net start/net stop wuauserv routines I found when searching the exact error message, I get the error:  System error 5 access denied.  I get the same message for several similar admin routines, particularly those involving "net".
    I have tried many of the supposed repairs, including MS Fix-Its, that appear in Google when I searched the error message.  None has worked.  (A couple Fixits I did manually and got the Access Denied messages again)  So I've rolled back using the restore point just prior to downloading the Lenovo programs, and everthing resumes working as expected.
    It seems that the Lenovo downloads are interfering with something, particularly my admin rights, in some way.  There's only one user (me) and it has admin rights, no password & etc.  Other odd things are Access Connections is running as is the basic Win 7 network app in the system tray.  Perhaps the Lenovo apps are interfering with the similar Win apps rather than replacing them as intended?
    Can anyone suggest an approach to solving my problem?
    Thanks,
    Greg

    Hello and welcome,
    It may be that TVSU is "updating" the AHCI driver (Intel Matrix Storage Manager or Rapid Storage Technology) to one that breaks Windows update.
    You can try rolling back the driver to an earlier version or going to the Intel site and getting a later one.
    http://forums.lenovo.com/t5/ThinkVantage-Technologies/ThinkVantage-System-Update-blocks-Windows-Upda...
    Z,
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Warum läuft Acrobat 8 Prof. nach der Installation von CS3 auf MAC nicht?

    Mein Acrobat 8 Prof. läuft nach der Installation von Adobe CS3 auf meinem MAC (OS 10.6.8) nicht und wenn ich Photoshop und die anderen Programme starte, kommt zunächst auch eine Fehlermeldung, dann laufen die Programme aber. Zugriffsrechte habe ich schon 5x repariert und das CS3 auch noch mal deinstalliert und alles neu gemacht - trotzdem! Was kann ich tun, damit alle Programme sauber laufen?

    Kann keiner wissen. Du verlierst dich hier in undefiniertem Rumgeeier. Wenn's 'ne Fehlermeldung gibt, dann sag uns doch mal, welche. Es gibt ja 'nen Grund, warum die kommt.
    Mylenium

  • Can't complete a clean installation of WIN 7 PRO on an Acer Aspire 4738

    Hello,
    If any one could help me with this problem i would really appreciate it.
    I have an Acer Aspire 4738-6888 (icore 5, 3GB RAM, 500GB HD), it was running win 7 ultimate 32 bits but started working erratically so i decided to perform a clean installation. HD was formatted entirely.
    Then tried installing WIN 7 PRO 64 bits from a DVD, but the installation program does not load and shows a kernel error oxc0000098
    It is funny that if i use a WIN 7 PRO 32 bits DVD, the installation programs loads and starts, everything seems to run normally (HD partitions can be created and formatted, Files are expanded and configuration begins) but just after the third restart
    when the assistant shows the message " preparing to run windows for the first time " the blue screen appears showing a "Memory_Management" error. Tried one more time but using a WIN 7 ULTIMATE 32 bits DVD with same results.
    Finally, I tried using the "repair option" from the DVD and get this message:
    StartupRepairOffline
    01: 6.1.7600.16385
    02: 6.1.7600.16385
    03: unknown
    04: 21350397
    05: ExternalMedia
    06: 1
    07: FailureDuringSetup
    OS version: 6.1.7601.2.1.0.256.1
    Regional config: 3082
    Before hand thanks a lot for your help,
    Rgds,
    GCH.

    Hi GustavoCh,
    What issue did you meet so you want to reinstall?
    Could you please use the Windows install image to install Windows in other computer or virtual machine? So we can make sure this issue is not caused by the image.
    I think this issue is related to hardware, please contact the manufacturer for better help.
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • Acrobat 8. Prbleme bei neu Installation nach Trial Installation von Acrobat 11

    Hallo I habe ein grosses Problem. Ich habe die Trial Version von Adobe Acrobat 11 installiert. Nach dem Testablauf habe ich wieder mein Acrobat 8 vom CSS3 installiert. Beim Programmaufmachen erhalte ich immer das Fenster mit Kaufaufforderung oder Sicherheitcodeangebe. Mein Sicherheitsschlüssel wird jedoch nicht angenomen. Was habe ich schon gemacht. 1.Schlüssel Recovery Programm installiert und durchgeführt. Erhalte die gleiche Medlung. 2.  Habe nach Vorgaben des Adobe Supports eine Installation eines im Paket CS3 eingeschlössenen Programm gemacht, das Programm aufgemacht und den Schlüssel eingegeben. Der Schjüssel wurde bestätigt. Jedoch erhalte ich beim Aufmachen des Adobe Acrobat wieder die gleiche Maske mit Kaufaufforderung. Adobe Support argumentiert, dass Sie keine Hilfe für CS3 leisten und schlägt vor, beim Forum nachzuschauen. Ich bitte um die Hilfe! Vielen Dank im Voraus. Valeria

    Ich danke dir für die Nachricht.
    Ich habe Windows XP, PC
    Ich habe CS3 Paket, alle Programme funktionieren einfwandfrei. Auch Acrobat 8, das zum Paket gehört. Jedoch vor der Installation von Acrobat 11.
    Nach meiner Recherche haben alle CS3-Generation Programme eine Seriennummer zzgl. Acrobat. Ich habe die Seriennummerl auch bei meinem Accout bei Adobe noch mal gecheckt
    Die Installation eines beliebigen Programmes aus dem Paket habe ich nach der Anweisungen des Adobe Service Mitarbeters gemacht. Hat sowieso nichts gebracht.
    Sie haben mir dann freundlich erklärt, dass sie mir nicht weiter helfen können und sowieso für diese uralte Programme nicht zuständig sind.  Das ist eine Sackgasse.
    Ich hoffe auf die Hilfe.
    Beste Grüße
    Valeria

  • Nach der Installation von Mavericks schaltet sich mein Macbook Pro ab!

    Seit der Installation von Mavericks schaltet sich mein Macbook Pro nach einiger Zeit bei Nichtbenutztung oder auch wenn itunes (Film oder Musik) läuft, einfach ab & startet dann neu mit der Anmeldemaske!
    Die Abschaltzeiten sind unterschiedlich zw. 20 und 40 min!
    Die Energieoptionen sind aus!
    Rechner ist am Netz - also keine Akkubetrieb!
    Hat jemand eine Idee?

    Du bist wahrscheinlich mit dem Problem, dass so viele von uns mit 2011 Maschinen werden mit - ein Defekt im Löten von der GPU, die erste wird allgemeine Ursache Bildschirm Probleme und schließlich zu einer unbrauchbar Maschine führen. Leider ist Apple die Anerkennung des Mangels und die einzige Angebot, das sie liefern den Nutzern ist eine Hauptplatine ausgetauscht werden - die bis $ 700 + USD aufrufen können.
    Einige Leute, die lange vorbei sind, werden mit Garantie neue GPU eingebaut. Dieser Prozess ist sehr viel billiger als eine neue Hauptplatine und scheint eine dauerhafte Lösung für den Mangel an.
    Um dieses Problem stoßen mehr lesen, siehe -> https://discussions.apple.com/thread/4766577?tstart=0.
    Viel Glück,
    Clinton
    PS: Dies wurde "übersetzt" vom Englischen ins Deutsche mit Google Translate - mich nicht für alles, was lächerlich klingen mag schuld!

  • IPhone 4s nach der Installation von ios7 defekt?

    Kann das iPhone 4s bei der Installation von ios7 defekt gehen (vgl golem)?

    Anyone fluent in German that can help this user?

  • Clean installation of Win 7 using UEFI and RAID

    Hi,
    I am trying to perform a clean UEFI installation of Windows 7 with SATA mode switched to RAID. I have two identical HDDs for RAID and 80 GB Intel 310 to put the OS on. The BIOS/UEFI can see all 3 drives and the two HDDs are configured for RAID through the CTRL-I utility
    When I start the Windows 7 installation, it does not find any hard drives and prompts me to load mass storage driver. I tried loading Intel Rapid Storage Technology drivers through USB flash drive, and the installation correctly displays "Intel(R) Mobile Express Chipset SATA RAID Controller", but after couple of seconds of loading when I click on Next, it comes back with the same result, no drives found.
    I tried switching SATA mode to AHCI and the installation recognizes all 3 hard drives just fine.
    Any help would be greatly appreciated.

    The BIOS to fix this issue has been released.
    BIOS here
    BIOS Text
    - Fixed an issue where Windows 7 64-bit/Windows Vista 64-bit installation might
      fail in UEFI mode in RAID configuration.

  • Warum tritt nach der Installation von Adobe Captivate 8 Probelme auf? Warum wird Adobe Captivate 8 nicht gestartet?

    Hallo,
    ich hab mir die Testversion von Adobe Captivate 8 installiert. Adobe Captivate kann nicht gestartet werden.
    Könnt Ihr mir bitte helfen, was die Ursache sein kann.
    VG
    Felix

    Please first check to see that your computer meets the minimum requirements: System requirements
    These links may  be helpful: 
    Captivate 8 Installation
    Adobe Captivate Learn & Support
    Pattie

  • Nach der Installation von Lightroom CC wird nun sowohl bei der Aktivierung von Lightroom als auch von Photoshop CC der Fehlercode 0cx000007b angezeigt. Somit kann ich beide Programme nicht nutzen.

    Da die Telefonische Kontaktaufnahme nicht funktionierte, lande ich nun hier.
    Klasse Service

    Ohne Systeminformationen und andere Details kann da keiner was sagen. Wenn sie bei der Aktivierung crashen, hast du entweder ein Netzwerkproblem oder Zugriffsprobleme mit der festplatte und die Aktivierungsdaten können nicht gespeichert werden.
    Mylenium

  • Nach Update auf 6.1.1 kein wifi

    Verbindung zu WLAN nicht möglich nach Update auf 6.1.1

    Hallo @dozeidle,
    hatte bis eben genau das gleiche Problem. Hoffe es bleibt beim "hatte".
    Nach dem IOS 6.1 Update wurde es täglich schlimmer mit der WLAN-Verbindung. Zuerst ging es noch, dann kamen Verbindungsunterbrechungen und die wurden permanent häufiger. Zeitweise musste ich erst das mobile Netz dazu schalten, dann ging WLAN für kurze Zeit wieder bis es wieder zusammenbrach. Bin fast verzweifelt. Und seit heute ging absolut nichts mehr. Hab dann ewig gesucht und war schon enttäuscht, dass ich hier auf deine Frage niemand meldete.
    Meines Erachtens könnte es damit zusammenhängen, dass das Gerät ja die Daten zu den ihm bekannten Netzwerken sozusagen für uns Nutzer nicht mehr sichtbar verschluckt und man da auch nichts mehr überprüfen kann, ob sich was verstellt hat, was ich auch als absoluten Mangel beurteile, denn es sammeln sich so doch so manche nur temporär genutzte Zugänge an, die da nicht hingehören. Unmittelbar nach dem IOS-Update waren bei mir, und wie ich weiß auch bei Anderen, auch die Daten zum mobilen Netzzugang verschwunden und mussten neu eingegeben werden.
    Also hab ich die Daten im Router für das WLAN geändert und anschließend mein 3GS mit diesem sozusagen für ihn neuen WLAN bekannt gemacht, also ein "Anderes" Netzwerk eingeben können. Zuvor hatte ich vergeblich versucht nur den Schlüssel im alten Netzwerk neu einzugeben, aber da machte das Gerät sich permanent selbständig. Ich dachte schon fast ich sei zu blöd dazu. Bis ich darauf gekommen bin und es hat geklappt. Nun hoffe ich natürlich, dass es bleibt und ich das Gerät wieder sinnvoll nutzen kann.
    Vielleicht nützt dir das ja auch. Würde mich auch interessieren, ob es bei dir auch geklappt hat.
    Viel Erfolg.

  • Clean Installation of Win8 on Pre-Installed G710 with Win8

    I have a new G710 with Pre-Installed Win8. I want to perform a clean installation of Win8. I have many reasons to do that: Disk partitions are not in the right sizes, the new computer is full with unwanted programs. I see that this issue is common to many users and there is no clear answer. If one of you knows how to do that and willing to share his solution with the forum, please do that. My impression is that Lenovo blocks the possibility to make clean installation using our current windows key and not providing us with proper installation media. The only solution they give us is using the recovery key or preparing recovery USB/DVD that replicate the un-wanted installation (Both solution didnt work in my computer).

    I have virtually the exact same configuration, whenever I install Windows I have to pull the HDD Caddy, put the Superdrive back in and run from bootcamp as usual. I have found no other way to install the initial Windows as a dual boot system (Vista or Win7).
    My issue is that I picked up the Win8 upgrade and installed it from USB - everything is fine until the system reboots at which point it goes to the standard Window boot problems screen and says it cannot start up Win8 as it cannot find various files, it offers to drop back to Win7 which then starts up fine.
    So, my question is having progressed a little futher down the line, any ideas why Win8 is not seeing the files during the boot process. The only thing I can see the base file systems may not be compatible.
    Thanks to anyone who cna help.

  • Cache-Probleme beim Kalender nach Installation von Mountain Lion

    Nach der Installation von ML kann ich nciht mehr auf meinen Kalender zugreifen, da ein Zugriffsproblem vorliegt. Wie kann ich das beheben?

    Hi heikeibe
    Can you get so far as to see/open any of the iWork apps themselves (eg Pages)?
    If so, if you click on the relevant name of the app (eg Pages) in the tool bar, and then click on "About Pages" you will see the serial number there: it will probably look something like this
    ABCD-EFGH-IJKL-123Z-ABCD-WYZ

  • Installation von Mountain Lion

    Muss ich nach der Installation von Mountain Lion meine Software (wie Time Machine oder AirPort Express) neu installieren rsp. konfigurieren?

    Ich verstehe ein bischen Deutsch... :-)
    Does this help?
    http://support.apple.com/kb/PH11278?viewlocale=de_DE

Maybe you are looking for

  • How Can I Enable "Creative S/W Synth" in Windows

    I have a "Sound Balster Li've! 5." sound card and I'm using Windows XP. When I was using Windows ME before, the MIDI output devices that were available in WinME were:- A: SB Li've! MIDI Synth2- B: SB Li've! MIDI Synth3- Creative S/W Synth4- MIDI Mapp

  • RMAN problem with block corruption

    Hi I have problem with the block corruption in one of the database . here is the error message . ora-01578:oracle data block corrupted (file# 10,block # 55309) ora-01110: data file 10: '/db/gist1/data/gist1_gis_nologging_01.dbf' ora-26040: data block

  • Why does selecting 'view' to see attached jpeg's download them?

    When I click on 'View' to see a jpeg attachment to an email, I expect it to stream the image. Instead the image downloads the same way it would if I selected 'Scan and Save to Computer' instead. Is there a way to get such jpeg attachments to be viewa

  • Radius Error 524

    I load Radius up on another server and get this message. Any ideas ? I already have Radius running on another server in the same tree. I'm just trying to launch another Radius service as a backup. Radius version 3.28 March 6, 2003

  • HT204407 I have an App icon that isnt appearing..It is definitely installed. Does anyone know how to fix this?

    I have an App icon that doesnt appear although it is definitely installed. Does anyone know how to fix this? thx Warren