Lenovo S10-2 won't start. Help!

Hello All!
Have a problem with my wife's Lenovo S10-2. Yesterday, after a 8-10 hours of netbook's inactivity (w/o heavy tasks), I found it deadly hanged. I turned it off by pressing a Power button by ~5 secs.
After turning on again, I see only blank screen with non-blinking cursor at top-left corner. No Lenovo's splash screen, no beeps, no reaction on F2 or other keys. It's still can be powered off by pressing Power for 5 secs.
Note: the cooler starts up with power on, but stops at same time as the blank screen with cursor appears.
Removing HDD and GSM card did not bring any effect. W/o RAM, netbook also doesn't say any beeps, but the screen is all black, with no backlight.
Tried to clear CMOS by removing a battery, power cord and pressing Power by 60 secs. No changes at all.
I also tried to enter BIOS recovery mode by pressing Fn-B while connecting power cord w/o battery. It starts with cooler working constantly, black screen (as described), but still no beeps. No SD or USB activity too -> no BIOS ROM search on external media.
The cursor is not blinking, does it mean anything? Could it be hanged by overheating in 2-3 seconds after power on?
I saw similar problems ten years ago with Intel Celeron 600, which halted after 8-10 seconds after powering on, because there were no thermal grease on CPU at all.
Any suggestions? What should I check?
P.S. Sorry for bad English, that's not my native language)

hi cdf.
i don't have s10-2 but as i remember it comes with soldered and another ram stick. it usually happens when the soldered ram is out of order but not sure what your problem really is.
still, whatever your issue is you will need hardware support cause you tried all of the suggestions that i may suggest. if you have valid warranty, contact lenovo support line for possible mainboard replacement.
hope this helps.

Similar Messages

Intel iMac won't start - HELP!

My iMac won't start this morning. I get the white screen with the grey apple,
and the swirling progress thing, then after a few seconds I can hear
the sound you hear when the system shuts down. like a soft switch
going off, then it just continues swirling, still with the white
screen and grey apple, then it restarts by itself. Then we go through
the same routine. Tried booting up by holding C with the Leopard disc inside but nothing happens.I have just reinstalled Leopard as Snow Leopard left too many printers and programs lifeless, so I did an erase and install a few days ago. Since then I have used the Mac fine, switched down normally last night, but this morning it doesn't want to play.
Any thoughts?
Thanks in anticipation
Chris
Message was edited by: ChrisRR

Have you reset PRAM and SMC?
Do this first
http://support.apple.com/kb/HT1379
and then do this, if the PRAM does not help
http://support.apple.com/kb/HT1543
The second one is basically disconnecting your iMac from power (and all cables), then reconnecting following a precise procedure.
If that does not help, I would restart with the Snow Leopard installation disc (insert disc and start up with the C key held down). You probably did an installation of Snow Leopard over your existing Leopard system the first time. This time, erase it completely first, then install Snow Leopard. I assume you backed up your data already.
When you get to the Installer screen (after selecting language), go up to the menu bar. Under Utilities, select to run Disk Utility. In the sidebar, select the internal DRIVE, not the volume indented under the drive. Go to the Erase tab. Name the volume +Macintosh HD+ and set the format to +Mac OS Extended (Journaled)+. Erase the drive. Since you have the drive selected in the sidebar (not the volume), it will also re-partition the drive.
It should take less than on minute to complete the process. Quit Disk Utility to go back to Installer. Run the standard installation onto the blank internal drive. Hopefully, a fresh Snow Leopard install on a reformatted/re-partitioned drive will work better for you.

Report developer won't start: HELP!

After i've installed reports developer DS edition. THe reportsbuilder won't start.
Can somebody help me. I've got appserver and database also installed and i've set de oracle home to the right location, but nothing helps. I've installed it on windows 2000 advanced server. When i installed the the developer suite on windows 2000 with app and database everything works fine. I've also installed it on windowsxp and there i've the same problem.
I get the instroduction logo, but afterwards reports developer won't start.
It stops when +/- 19mb has been loaded (task manager.
I'm desperate can somebody help me.

Hello,
On Windows, NLS_LANG can be set in the registry or as an
environment variable.
You can test with the commands :
set NLS_LANG=AMERICAN_AMERICA.WE8ISO8859P1
rwbuilder.exe
Then,if it works, change the NLS_LANG in the registry
(HKLM/Software/ORACLE/Homex)
regards

My ipad won't start, help?

Help....original iPad, 16 gig, won't start. Tried re-start (holding home and power buttons for 30 secs) won't come on. Fully charged. Perimeter of screen shows some light, nothing else. PLEASE HELP!!
P.

Try a reset:
1. Hold the Sleep and Home button down (together)
2. For about 10 seconds
3. Until you see the Apple logo (very important)
4. Ignore the red slider

EMac won't start, help please

I am having two problems with my eMac. The first, much more pressing, problem is that it won't start. I was having problems installing the newest version of quicktime, so on the quicktime forums I read to Repair Permissions in the Disk Utility, so I did this, and everything seemed to go well, but when I restarted my computer, it would not load. It is stuck on a light grey screen with a dark grey apple logo in the middle. My keyboard won't repond to the point where i can't even open the disk drive. My second, much less urgent problem is that my disk drive doesn't recoginize any cd's, even ones that I have used with this computer before. this problem really means nothing at this point, since my computer won't start anyways.
If anyone could help me, it would be greatly appreciated.

Yes, I tied all of the suggestions for my problem.
You see a blank, gray screen
1. Make sure the latest firmware for your computer is installed. Check Apple Downloads for the latest versions. (Yes, it is installed)
2. Disconnect all peripheral devices, except for the Apple keyboard and mouse. This includes ADB, serial, USB, FireWire, SCSI, and PCMCIA devices. If this resolves the issue, connect one device at a time, restarting after each one, until you've determined which device is causing the issue. (All are disconnected)
3. Remove third-party hardware upgrades such as memory (RAM), microprocessor upgrade cards, and PCI cards. If this resolves the issue, add back one item at a time, restarting after each one, to isolate the issue. Note: Apple does not provide technical support for Mac OS X when used with third-party microprocessor upgrade cards. (Don't even have any third-party hardware upgrades)
4. Start up from your Mac OS X installation disc and check the hard disk with Disk Utility or, if necessary, fsck. (CD-drive will not even open, so can't do this)
5. If you are comfortable doing so, reset your computer's Power Management Unit. Specific directions are available elsewhere in the Knowledge Base. (Can't find how to do this on the anywhere)
6. Additional tips may be available in this document. (Document also had nothing that worker)
I will be buying a macbook regardless after my income tax comes in, so I don't deem the computer as worthy of spending any money to fix, but this was a pretty expensive machine to just discard, so I would like to try to get it running again.

Lenovo s10-2 won't detect camera

Hello, I've had my lenovo s10-2 for a couple of months and the camera was working fine and then it stopped working it. It does not detect it any more. Any advice?
I have windows XP home edition and SP2

A family member of mine has the same problem on his S-10. I've been researching the dickens out of this.
Finally determined that if I opened the lid (display) about half way, the camera would be found and connected as if I plugged it in to the USB. Camera worked too.
I took the unit apart and found the very fine wires bound in a woven sheathing that connect the USB camera to system board go right past the hinge in a somewhat precarious way. And with enough opening and closing the display they apparently frey as I believe has happened in this case and ultimately break.
Note part #4 in this picture. This camera cable "44C9901" would need to be replaced.
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-71076#4
Unless you have experience with laptop repair and/or are certified with Lenovo devices, I would not recommend you try to repair this yourself.
This S10 is not much beyond a year old. It is used opened/closed and used multiple times daily. Bottom line. The design isn't what it should be.

Upgraded to Yosemite and now my laptop won't start HELP!!!

Last night I upgraded my Mac BookPro with yosemite and don't know if I did the right thing, my laptop won't startup, where the apple logo appears, after like 10-20sec, it appear a Decline logo and won't start, WHAT CAN I DO? Is there a way back? I had it for like 5 minutes and my computer was really slow and Microsoft Office, iMessages didn't open. I had to restart my computer and then I got stuck with the Decline LOGO!

Troubleshooting Apple Mail
Troubleshooting sending email messages

U430 stucked at Lenovo screen, BIOS won't start either

Hi, I have IdeaPad u430 touch, six monts old. I had some blue screens in the past, I cleaned all possible viruses and diagnosed hard disc with no results. Laptop was running smooth until now.
I shut it down last night and today it restarted itself couple times and then I wasn't able to start it at all. It gets stuck at Lenovo screen, no Windows loading circle/dots.., I can't access BIOS or anything else through the novo button, it just gives me the Lenovo screen again. F2 does not work either.
I also noticed that when I tried to install updates it wouldn't do anything just spinned the Windows buisy icon for a while, if that can be any clue.
I haven't removed the battery yet, as it is under cover which needs to be unscrewed. The computer is still under warranty. I'm not sure if opening the cover wouldn't viod the warranty. I'm not impressed, my boyfriends IdeaPad has been good for six years
Any suggestions on how to boot the computer again or what's wrong with it? I'm totally done today, tomorrow I'm calling support, but I'm not sure how they can be helpful, if the computer won't boot at all...
M.
Solved!
Go to Solution.

Hi Martinka,
Welcome to the Forums
As per the query we understood that you are facing issue with system hangs at post in your U430 laptop.
Does the system overheats, as this might be issue with the motherboard please visit the nearest service center.
Click here to open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
Hope this helps. Do post back if the issue persists!
Best regards,
Ashwin. S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

I book won't start- help requested ASAP

I have had my Ibook for about 3 years now. Today I was burning a disk in the Itunes applicatoin as well as searching the internet. When the disk had 2 tracks to burn left, my computer shut down. Since then, I have been unable to restart it. I have tried to press the power( ON) button many times, but it will not restart. The 7th and 8th time I tried to restart it, it made a slight clicking noise. What can I do? I need to use my computer ASAP for homework and debate work. Please help.
Thanks
Kate

Welcome to Apple Discussions!
Here's a place to start: Troubleshooting: My computer won't turn on:
http://docs.info.apple.com/article.html?artnum=300552
See if anything here helps. Please post back with any results or further questions.
Good luck!

Brand new imac won't start HELP!!

Just got an iMac, fresh out of the box I hit the power button, everything looks normal, OS X does its normal checks, then the desktop comes up with multicolour stripes - the desktop is cluttered with all kinds of files - a darwin console opens up then an application called Phoenix starts does a few things that were too quick and then just says PAUSED in an orange box at the top and nothing else.
I have a bluetooth mouse and keyboard so I can't actually control the thing in any way either.
It also looks like OS X 10.5 has not been pre-installed.
Please can someone help me with a suggestions as to what I can do.
(I am an experienced Mac User having used them since the original SE - I've never experienced something like this before)
Thanks

it sounds like the iBook went to sleep during the transfer or at least it's hard drive spun down.
what you need to know is hope that simply booting from your install DVD will let you repair the iMac's hard drive. You could also try booting holding down the Command S keys on startup and when you get to the Single User Mode command line prompt follow the directions there for running fsck to repair your hard drive.
Do you have a FW hard drive? Can you copy files from iBook to FW and then from there to iMac?
And, it is always nice to have a FW emergency/backup hard drive. The iMac needs a different partition scheme to be bootable from FW than the iBook does, but you can create the proper partition type etc from a Tiger Installer and put OS X on FireWire, then see if you can backup and repair your iMac's hard drive.
MicroMat's TechTool Pro 4.5.1 is now shipping and is compatible, Universal Binary and bootable. Always good to have some 3rd party utility handy.
If you are just starting out, you probably don't have much if anything installed yet, so you may want to just erase your iMac drive and restore to what it was. That would be the easiest if Disk Utility won't repair it.
Instead of powering off the iBook, I would have tried to force quit whatever was running, like Migration Assistant.

Console service won't start -help

I have create C:\oracle\product\10.1.0\
database, after the copmletion of the creattion the console was up running, but after i have close my computer I can't get hold on the console.
http://localhost:5500/em/console.
then I went to look at the windows service and find that the console service is not started, but when I stry to start it, i get the error that the service could not start and the error code is 2.
but all the other services are started.

When I try to start the dbconsole, it is giving the error as shown below.
D:\applns\oracle\product\10.1.0\db_1\BIN>emctl start dbconsole
Oracle Enterprise Manager 10g Database Control Release 10.1.0.2.0
Copyright (c) 1996, 2004 Oracle Corporation. All rights reserved.
http://C2048:5500/em/console/aboutApplication
Starting Oracle Enterprise Manager 10g Database Control ...The OracleDBConsoleorcl service is starting.
The OracleDBConsoleorcl service could not be started.
The service did not report an error.
More help is available by typing NET HELPMSG 3534.
D:\applns\oracle\product\10.1.0\db_1\BIN>net helpmsg 3534
The service did not report an error.
What could be the reason? Can somebody help me?

MACBOOK WON'T START HELP HELP OMG HELP!!/1/1kghl

SO! I recently bought a white MacBook and an iPod Nano (gen1 because I wanted them to match). Since then I have had to send in the first iPod, get a second one, and have the exact same problem--neither the MacBook nor the iPod seem to realise at all when they are plugged in. No charging, no syncing with iTunes. Nothing.
So the customer service bloke told me that I should update OS X. Alright, I toddle on off to Barnes and Noble to take advantage of the Wifi, as I live in the middle of no where and am still on dial-up. Update, update, restart time. I'm supposed to hold down the power button while it restarts.
Familiar with having to hold down keys while things happen, as I've used Windows all my life, I do. Except, apparently my button-pressing skills are TOO well-honed, because it begins loading and then turns off! Oh no! I may have held that button down a bit too long...
Easily solved, right? Just boot it up again.
Except it won't turn on! Well the little flashy LED light goes all flashy, and the thing sort of growls at me like it's in pain. The screen stays black, nothing else happens. I hold down a lot of buttons and still nothing happens. I've been trying turning it on while holding down different buttons, but still nothing. Honestly, I don't handle panic very well.
So, basically. I am totally freaking out. HELP HELP HELP PLEASE HELP.
Please pretty please?
X-POSTED FROM INSTALLATION & WHATNOT FORUMS BECAUSE I AM TOTALLY FRANTIC. Sorry!

Welcome to Apple Discussions!
First off, please don't crosspost your question unless instructed to, as it only wastes bandwidth and makes it harder to track who is asking what question.
Second, sleep it off a night, with your machine unplugged and no battery inserted to get rid of your franticness. It never really pays to be frantic in front of a computer because you don't know what you are doing, and you could be your own worst enemy.
When you are ready, depress the power button only for 2 seconds and let go.
If that doesn't work reset the power manager:
http://docs.info.apple.com/article.html?artnum=303319
Also try zapping the PRAM if that doesn't work:
http://docs.info.apple.com/article.html?artnum=2238
If neither works, are you getting anything on the screen?

Lightroom won't start-Help

I am running Lightroom 2.5 on a Windows Vista System. I have been using Lightroom since version 1.0. My Lightroom has suddenly quit working, When I start I either get a message that Lightroom has stopped working and must be shut down or it dims and says not responding. I have left it in not responding mode for 5 hours with no luck. I have tried loading other catalogs and even creating a new catalog and I get the same results. What I see when it goes to Not Responding is strange. Customizations that I have made are not shown. The folders listed do not seem to be the folders that should be shown for the catalog and I sometimes get a screen asking me to set program update options. What has happened and what can I do? Help

I have tried creating a new catalog. Same result.
The message I get says: Adobe Photoshop Lightroom 64-bit has stopped working
A problem caused the program to stop working correctly.
Windows will close the program and notify you if a solution is available.
Everything else seems to be working normally.

CHANGED OS LOGIC WON'T START HELP!!

I need help! My 2x2.0 G5 died. I ran 10.41 and Logic Pro quite well. I got a temporary 2X1.8 G5 that had 10,5 on it. I installed 2 1/2 days worth of software and everything worked but Logic was unbearably liimited and sloooow. To try to get a few weeks work done until a Nehalem finds me. I changed the OS back to 10.4 I't had to be archive and install to go "backwards" I have a folder called "old system now. Everything is working fine except Logic. It won't even open. Is there something I can do about keychain or moving some of those 'Old system" library files to get Logic to work without having to reinstall Logic Pro twice in one week and lose preference I set up in the past week. Thanks for your help. Zangsax

What do you mean by safe mode is single user mode? ("apple+s" combination?)
There may be a hardware failure on your harddisk. Can you boot from your install DVD? Try that, run Disk Utility, and check the entire disk for errors (click repair disk).

My iMac won't start, , help!

Hi, I have a new imac which I have just setup, all of a sudden the screen went black and the fan started running loudly. I can't get any response from it other than the fan. Tried turning on and off again but don't know what else to do Any ideas guys??

Welcome to Apple Support Communities
Do a SMC reset > http://support.apple.com/kb/HT3964 Also, reset the PRAM > http://support.apple.com/kb/HT1379
If it doesn't work, take the iMac to the place where you purchased it and it will be replaced free of charge

Lenovo S10-2 won't start. Help!

Similar Messages

Maybe you are looking for