Lenovo S10-3T пароль BIOS

Здравствуйте !Недавно откопал у себя старенький S10-3T - включил - ноут выдал ошибку CMOS Checksum Error - Defaults Loaded - при этом теперь при входе в BIOS запрашивается пароль, какой пароль - неизвестно, естественно зайти в него не получается, а надо Пробовал обновить BIOS с сайта тех. подержки Lenovo(Версия 24CN62WW, ссылка http://support.lenovo.com/ru/ru/products/laptops-and-netbooks/ideapad-s-series-netbooks/ideapad-s10-3t/downloads/DS010786) - пароль не снялся. Как можно пофиксить эту ошибку?

@flyingstore,
Kindly contact the service center as they will have a fix for this issue, I've sent you a PM explaining more about it. Do check your PM.
//JameZ
Check out the Community Knowledge Base for hints and tips.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
X240 | 8GB RAM | 512GB Samsung SSD

Similar Messages

Lenovo S10-3 Fan Control (Linux) and overheating

Good day to everyone.
Let me describe the situation. My Lenovo S10-3 is always hot (even in idle) and uses internal fan very often. It irritates very much because fan is noisy (service found no problem).
Sensors: acpi-tz ~60C, core ~50C (idle).
But even fan is disabled (connector is pulled out from motherboard) temperature becomes not much higher --- approx 65-70C.
Now, the question: is there any way to override BIOS fan control values? (e.g. 55C="Fan on" to 60C="Fan On")
For the S10 series there is program named "Fan Control", but it doesn't work on S10-3 and this program is for MS Windows only. Can anyone give comprehensive ansver/guide how to control fan speed (or on/off temperature values) using native linux tools or special program? It might be very useful for others who experiences the same problem. Thanks.

The heatsink is not connected to the surface of CPU and GPU and this is why you said that disabling the fan doesn't make any difference in the temperature. There are two pieces of thermal pad on the CPU and GPU.They are actually unusable. Remove them. Put thermal paste on the surface of CPU and GPU and heatsink and then put a piece of copper on CPU and GPU. This will make connection between heatsink and surface of CPU. This will make the fan usefull . Do this at your own risk (There is no risk. But use suitable pieces of copper is very important.) Using google will help you find about this issue

Lenovo S10-2 won't start. Help!

Hello All!
Have a problem with my wife's Lenovo S10-2. Yesterday, after a 8-10 hours of netbook's inactivity (w/o heavy tasks), I found it deadly hanged. I turned it off by pressing a Power button by ~5 secs.
After turning on again, I see only blank screen with non-blinking cursor at top-left corner. No Lenovo's splash screen, no beeps, no reaction on F2 or other keys. It's still can be powered off by pressing Power for 5 secs.
Note: the cooler starts up with power on, but stops at same time as the blank screen with cursor appears.
Removing HDD and GSM card did not bring any effect. W/o RAM, netbook also doesn't say any beeps, but the screen is all black, with no backlight.
Tried to clear CMOS by removing a battery, power cord and pressing Power by 60 secs. No changes at all.
I also tried to enter BIOS recovery mode by pressing Fn-B while connecting power cord w/o battery. It starts with cooler working constantly, black screen (as described), but still no beeps. No SD or USB activity too -> no BIOS ROM search on external media.
The cursor is not blinking, does it mean anything? Could it be hanged by overheating in 2-3 seconds after power on?
I saw similar problems ten years ago with Intel Celeron 600, which halted after 8-10 seconds after powering on, because there were no thermal grease on CPU at all.
Any suggestions? What should I check?
P.S. Sorry for bad English, that's not my native language)

hi cdf.
i don't have s10-2 but as i remember it comes with soldered and another ram stick. it usually happens when the soldered ram is out of order but not sure what your problem really is.
still, whatever your issue is you will need hardware support cause you tried all of the suggestions that i may suggest. if you have valid warranty, contact lenovo support line for possible mainboard replacement.
hope this helps.

Installing XP Pro on Lenovo S10-2

Hello.
I have the full legal version of XP Pro and I am having issues installing this on my new Lenovo S10-2.
I have the regular CD (Orig XP - no Service Packs) as well as XP Pro with SP3 slipstreamed into it.
It will not install either of these.... I have tried installed from external CD-Rom's and USB Stick.
I do IT work and I am having issues... so I asked my company's IT dept to have a look -
This is the email from them:
"Wednesday, July 22, 2009 6:03:43 PM by IT Dept:
Used the external DVD writer as a CD drive to load WinXP pro.
Netbook saw the drive & got started but stopped at blue screen of death before reaching the 1st navigation screen.
Tried dumbing down the drive with a plain CD-ROM drive on a tether & got the same result.
Tried launching an upgrade from Windows already on the netbook & make some progress, but as soon is it rebooted, it could not continue & had a "drive read error".
Tried turning the resident O/S back from SP3 to SP2 & tried my WinXP install CD but got a similar result.
Fellow IT's brother is a superior tech who has some practical experience with netbooks.
His first recommendation coincided with what the blue screen said: scan for infections & run CheckDisk.
He recommended MbAm.
Slaved HDD to STtest & swept with MbAm: nothing found.
Ran chkdsk.exe & also did well.
He scanned some forums & found that Microsoft has gone out of their way to make sure netbooks could not be upgraded.
Gave up on it & informed user."
Does anyone have any ideas or suggestions please?
I have to have XP Pro to be able to use this on my companies network.
Thanks so much!
Sam
Message Edited by keysh2oboy on 07-23-2009 02:28 PM
Message Edited by keysh2oboy on 07-23-2009 02:30 PM

Hi,  thanks for more information about that ..
in BIOS is Configuration page SATA Controller working mode the only user setting from Compatible & AHCI....
i never changed this, cause on my S10e i could install everything without any change...
The only one thing i do not with windows itself is partition & formating with acronis Diskmanager before install,
i delete all exitsting partitions & repartitioned given minimum 20- 30 GB active NTFS & the rest 120 GB logic for data & room for backup with acronis trueimage...
i never do this with windows itself.....
..you says ...the only menu option gives you 32GB is strange, whole harddrive must be 149,05 GigaByte =160 GB...
if harddrive could be never partitioned, even with other computer... the harddrive have a faulty or wrong firmware...
try in BIOS F9 for setup defaults and then these AHCI & Compatible settings in BIOS ... (AHCI is default)
i always have 2 or more other harddrives (the one i used as provingground for all new scenarios is the little 160 GB   )... at last option i would try other harddrive (fresh or complete unpartition)...
sincerely KalvinKlein.   .
Message Edited by KalvinKlein on 07-24-2009 11:23 AM
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

Lenovo S10-3t Part of the touchscreen not Working

Hi,
I have lenovo s10-3t with win 7 home premium. Recently I found out that part of my touch screen is not working. I tried calibrating and resetting the calibration data, but no success in getting the touch screen working correctly. Then I reinstalled the intel graphics drivers. The touch screen started working correctly. After one day the issue has resurfaced. Have no idea what is wrong. (to depit the dehaviour I have added a paint screenhot, the area highlighted with red oval, is where touch screen is not working)
Link to picture
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

I cant be sure,but its better to take it to your nearest service center and have it checked.Which city do you reside in?Il try to point you to your nearest service center
Cheers and regards,
• » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo

Lenovo s10-2 won't detect camera

Hello, I've had my lenovo s10-2 for a couple of months and the camera was working fine and then it stopped working it. It does not detect it any more. Any advice?
I have windows XP home edition and SP2

A family member of mine has the same problem on his S-10. I've been researching the dickens out of this.
Finally determined that if I opened the lid (display) about half way, the camera would be found and connected as if I plugged it in to the USB. Camera worked too.
I took the unit apart and found the very fine wires bound in a woven sheathing that connect the USB camera to system board go right past the hinge in a somewhat precarious way. And with enough opening and closing the display they apparently frey as I believe has happened in this case and ultimately break.
Note part #4 in this picture. This camera cable "44C9901" would need to be replaced.
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-71076#4
Unless you have experience with laptop repair and/or are certified with Lenovo devices, I would not recommend you try to repair this yourself.
This S10 is not much beyond a year old. It is used opened/closed and used multiple times daily. Bottom line. The design isn't what it should be.

Just open new Lenovo S10 from RadioShack...built-in mic help please....

Hello . I'm Ricardo & today I just opened up my new Lenovo S10 I bought from RadioShack. How ever, I have been having trouble with the built in mic. It is only hearing on very low levels. I tried doing what was done in another forum post here, but to no avail. So, now I'm stuck & need some help. Please. Thank you. God bless :smileyhappy .

Hi and welcome...
in sound volume mixer there is a point advanced setting ...set a hook at microphone boost ...
sincerely KalvinKlein
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

PhotoShop 5 organizer startup on a Lenovo S10 netbook incorrectly blocked

I installed PSE5 on a new Lenovo S10 netbook which has a 1024x600 resolution screen.
Startup of Organizer is blocked by an PSE5 dialog box that states "VGA resolution is required". Ok, VGA is 640x480, so why should this error appear on startup with a 1024x600 display?
If I switch my netbook display to an external monitor of 1024x768 res PSE5 starts without the error. Then I can switch the current display back to the netbook and it works fine.
So Adobe, is there a patch or workaround that will let me start PSE5 on a 1024x600 resolution display? Netbooks are quickly starting to capture the low end of the notebook market, and an increasing number of netbook customers will run into this artifical PSE5 limitation. While I don't expect to be doing heavy duty photo editing from a netbook, the ability or use the organize (view, tag, delete etc.) is desirable.
Chris

Chris, the minimum resolution for PSE 5.0 is 1024 x 768 - there is no
work around. You will have dialogs and other windows cut off if you run
at a lower resolution.
-Trish

New Lenovo S10 Model Info Please

I would like to know when the new model of the S10 series will be released, i found this article on Cnet.com http://ces.cnet.com/8301-19167_1-10130797-100.html?tag=mncol;title and i wanted to know when these features would be avalible, or if they are already avalible but just not listed on the website. The features are the new splashtop or quickstart OS and the veriface security program. Any information woule be great, i am very egar to get my Lenovo S10 netbook and have been waiting a very long time for these features to come out. And if there is something newer that is going to come out hardware or software wise, could anyone who knows please say so here. i want to get the newest version of the netbook that i can.
Thank you!

my S10e also included both.. but i think veriface is just a marketing hype as its nearly useless..
AMD Phenom II X6 1055T / 2xATI HD5770 CF / 8GB DDR3 / 4x500GB RAID-5 / Win 7 Ultimate x64
Lenovo S10e Black / 2GB DDR2 / 160GB HDD / 6-cell battery / Win 7 Ultimate x86
Motorola Xoom

Alt key stucks (not physically) in my lenovo s10-3t

Alt key stucks in my lenovo s10-3t and i have to press it 2 or 3 times to release it .... i encourted this problem in tablet mode so i think that this is not a physical keyboard problem ...

due to i don't have s10-3t, i suggest you to check the manuals first. it should have some informations about cleaning the keyboard.

How to check used lenovo s10-3t before buying?

hi gurus...i planning to buy a used lenovo s10-3t. can you give me a list of check items to ensure that it is still in good working condition?

i suggest you to buy it online from ebay kind websites. some of sellers accepts return so if you don't like it, it won't be a problem.

Lenovo s10-3c

I have lenovo s10-3c , but whenever i try to find a device it doesn't shows a device... I have no idea why it is not working .... I want know how do I activate my Bluetooth of m laptop... Is there already a Bluetooth device installed in my laptop or I have to get a adapter for it...... I also want know is there any bluetooth button on my laptop .... N also want solutions for activating the Bluetooth in my computer

if you don't see any options to activate bluetooth when you press fn + f5, i can say your computer didn't come with bluetooth support.
( unless if there is any unknown/not-installed device under device management )

Cell Phone Causes Lenovo S10 to Reboot

I left my Nokia E71 on the Lenovo S10's keyboard only to turn around to see it had randomly rebooted. Further investigation showed it can be easily recreated on the S10 while the IBM X60 Tablet did great.
Youtube video of reboot:
http://www.youtube.com/watch?v=rAypYOTubHs
My site:
http://www.jasonhui.ca/2009/03/30/cell-phone-causes-lenovo-s10-to-reboot/

I had this problem too. Specifically a Dlink router (WBR-1310) and a Lenovo laptop (Y530) running Vista Home (32-bit). It would show that my laptop connected to the network, then a few seconds later the connection would be down and it would continuously connect/disconnect. My other system that was connected just fine through the router (running Windows 7) would get kicked off the network. Connecting the Vista laptop directly to the cable modem, though, would work just fine.
Found this post, and it worked for me. http://www.justanswer.com/questions/1wau3-bought-lenovo-laptop-y430
Just go into your Dlink configuration's Advanced tab, then the Advanced Network sub-tab. Uncheck the UPnP (universal plug and play), save the settings, and let the router reboot.
Now both my systems (Vista and Windows 7) are happy and connected through the router.

Lenovo S10 and Lenovo S10e leather covers

howdy
this is completey superficial but never the less something i hope you know the answer to
Do the leather book covers for the Lenovo S10 fit the Lenovo S10e
Those slip on covers are great but i want a more business and easy access style
So far i haven't found any threads about this subject
thanks in advance
kit
practice random acts of kindness and senseless acts of beauty
Solved!
Go to Solution.

Thanks JB
I was hoping so
cheers for the confirmation
practice random acts of kindness and senseless acts of beauty

Lenovo G 500s Insyde bios brick looking for right filename for biosdata to recovery

Hey,
as you can read in the subject, ich bricked my bios V2.02 when i tried to flash a whitelist-free-bios to my notebook Lenovo G 500s.
Before i tried to update bios, i made a backup of my current bios in .rom format.
I used Andy's tool to get the right filename, the tool gave out: "VILG1X64.F?"
Then I copied the biosfile to a usb stick with activity-led several times with dirrefent filenames and fileendings:
VILG1X64. fd/rom/bin/bi
VILG1X64. fd/rom/bin/bi
VILG1X64. fd/rom/bin/bi
VILG1X64. fd/rom/bin/bi
VILG1X64. fd/rom/bin/bi
VILG1X64. fd/rom/bin/bi
1X64. fd/rom/bin/bi
VILG. fd/rom/bin/bi
Anybody with the same notebook, who knows which filename i need? Which file-ending is the right?
Some Info:
I also tried to use the .rom file from lenovo's .exe file bios update from official download centre.
Thank you!

Hi, I have an x120e and when I get into the BIOS > Startup > Boot, I see the following list:
Boot Priority Order
1. ATA HDD0 Samsung SSD 830 Series (my main disk)
2. USB HDD SanDisk Cruzer Fit (a tiny usb drive that is always attached and holds assorted files)
3. USB CD
4. USB FDD
5. PCI LAN
The device can indeed boot from a USB stick. I think you will have to follow this order of events: first attach the USB you want to boot from, yet boot only from your main hard drive, to let the system recognize the attached USB drive and put it in the Boot Priority Order list, then shutdown, restart and get into BIOS. F1: to either to change the ordering in the list to put USB FDD or USB HDD SanDisk first) or F12 (I think): to choose a temp device to boot from. Or....... (another thought), the USB you want to boot from hasn't yet been made "bootable" (I think you may have to go into diskpart > etc to set it active) so isn't recognized in BIOS.
I've used a USB flash drive with my recovery partition on it to restore to factory state. That was also a Sandisk Cruzer USB. I've also booted directly into a WinPE sort of environment using another bootable USB made for the purpose of restoring from system images. Mine is an x120e; your x121e can't be much different.
Cheers!

Lenovo S10-3T пароль BIOS

Similar Messages

Maybe you are looking for