Lenovo s10 3t sleeping mode not working???

I just received my lenovo ideapad 2 days ago and upgraded to ultimate.. my problem is , even before i upgraded it and it was on windows starter, whenever i put on sleeping or hibernate mode, it actually SHUTS DOWN? after putting/thinking it was on sleeping mode, i tried to turn it on again, hoping that it will go back to where it was before., then i realized, i have to go on the safe mode or start normally coz it said it didn't properly shuts down. BUT i didn't even shut it down.. i only put it on sleeping mode.. why is it so? anyone have the same prob? or am i pressing the wrong button (the power button) in order to turn it back on from the sleeping mode.. it really bugs me that it always kinda restarting when it is supposed to be asleep!!! i changed the power setting to having the sleep mode longer than an  hour and tested it within few minutes by putting on the sleep mode and try to put it back on, it still goes into computer not properly shut down ---> safe mode or start normally window thingy.. what is wrong here???
HELP PLEASE.. thanks a bunch..
Solved!
Go to Solution.

Hi and welcome, did you install Lenovo Energymanagement there are some points to configure...
here an excerpts of my article... .. the settings .. way gettin in
Energy Management -->advanced tab
Section options  check Enable Hibernation check Auto adjust schemes according to battery power
Sectionower buttons  When I close the lid of my portable computer  choose Stand By
When I press the power button on my computer  choose Shut Down
When i press the sleep button on my computer (Hint: on S-Series Fn-F1)  choose hibernation
sincerely KalvinKlein
Want more ? For further information to get the most of your S-Class machine
Lenovo Energymanagement   Backup  Windows 7 Driver   Windows 7  Install
Clean XP Install  XP Startup  Small WebCam Guide  Lenovo Easy Capture
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

Similar Messages

  • Windows 10 sleep mode not working

    windows 10 sleep mode not working

    I hope this helps. But... I had the same problem last week. Now I don't as of 8/17/15. I am not sure if a windows 10 update fixed this. I do not like problems that without any assistance fix themselves. However, try sleep mode again. This problem may have been fixed.

  • Stand-by / sleep mode not working when USB is connected

    Hello!
    When the USB cable from my 24" LED Cinema Display is connected to my new Mac Pro 2,66 GHz Quad-Core, the stand-by / sleep mode does not work correctly: the Mac Pro goes to sleep normally, then the LED behind the on-/off-button flashes one time and then the Mac Pro awakes from sleep mode without any user interaction.
    I already tried to reset PRAM, I tested all three rear-side USB connectors (I did not test the front-side USB connectors because the display's cable is way too short), I unplugged all other USB and Firewire devices and also tried sleep mode from a freshly created account. Alas, nothing helps.
    As soon as the display's USB connector is plugged in, sleep mode does not work any more. It even doesn't matter if there are USB devices plugged into the display. Without connecting the display's USB plug, sleep mode works fine.
    So, any ideas out there?
    Thanks in advance & best regards!
    Mario.

    I fixed the problem, so I just post this to help others that might run into the same trouble.
    The Mac Pro and the display were connected to a master/slave power socket. The problem is: when the Mac Pro goes to sleep, there still seems to be some power left in the display (which socket is switched off by the master/slave power socket). Therefore, the display goes off slightly after the Mac Pro. This powering off seems to release a signal on the display's USB wire that is connected to the Mac Pro and therefore switches the Mac Pro on again.
    So, this is the same effect as removing a USB device from the Mac during sleep mode, what (at least in most cases) also starts up the Mac again.
    As a result, there seems to be no other solution to this problem than removing the display from the master/slave power socket. Sadly enough, the LED Cinema Display consumes other 2 watts in stand-by mode...
    Cheers!
    Mario.

  • Sleep mode not working properly on Macbook Pro

    On my Macbook Pro everytime my mac enters sleep mode just the display goes to sleep never the system even after 8 hours. Checked the energy saver setting both display and computer are set to ten minutes. I can also never get the display to wake back up unless i do a hard reset. Any ideas? Thanks!

    Does it now work only on battery? or using the power supply?
    If only on the power supply use a grounded plug.
    Otherwise try reseating touchpad cable. Post the size and year of your MBP.

  • Sleep mode not working properly in windows

    I have a P67A-GD65 working fine (THANK GOODNESS!) but I have a small annoyance.. It wont wake up from sleep mode unless the power button is pressed! How can I change this to wake up on say, when I click a button on my mouse or my keyboard or even move the mouse? I have the latest bios installed. Thanks!

     Depends if you have USB or PS/2 KB/mouse
      Resume From S3 by USB Device
    The item allows the activity of the USB device to wake up the system from S3 (Suspend
    to RAM) sleep state.
      Resume From S3/S4/S5 by PS/2 Mouse/ Keyboard
    These items determine whether the system will be awakened from what power saving
    modes when input signal of the PS/2 mouse/ keyboard is detected.

  • Sleep mode not working after iMac WLAN Update 1.0

    Hello,
    unfortunately the sleep mode isn't working anymore after the latest "iMac WLAN Update 1.0" update.
    Usually I press cmd+alt+eject to activate the sleep mode, since the update the screen switches off (black) for a second and immediately turns on again. Fans and HD keep running without any interruption.
    Same behaviour if I use the "sleep mode" command from the Apple menu, except the screen turns off and keeps off, but fans and HD are still running.
    The iMac never activates the sleep mode by itself (e.g. after 15 minutes), this also a new "feature" which occured after the update.
    Is there anyone recognizing the same problems? Any hints how it can be solved?
    Thank you very much in advance,
    Oliver

    I finally found the solution in a German newsgroup. First: It has nothing to do with the "iMac WLAN Update 1.0" .
    A unsuccessful printer job caused the problem and just open the CUPS site http://127.0.0.1:631/jobs and delete the hanging job solved the problem!
    Thanks,
    Oliver

  • My sleep mode not working right why?

    My Mac Pro comes back on during the night when it's in sleep mode.Why?

    It could be Bluetooth.  Do you have Bluetooth wireless mouse and keyboard?
    I had this problem until recently.  It seems to have gone away since updating OS X to 10.8.5.
    Open Console next time this happens to you.  Scroll to the point at which the machine went to sleep and then awakened.
    If you see something like what I've pasted below, then you're bluetooth devices are waking the machine.
    10/13/13 1:06:45.000 AM kernel[0]: Wake reason: UHC6
    10/13/13 8:45:44.000 AM kernel[0]: 0x1face000, 0  Intel82574L::setLinkStatus - not active
    10/13/13 8:45:44.000 AM kernel[0]: 0x1face001, 0  Intel82574L::setLinkStatus - not active
    10/13/13 8:45:44.000 AM kernel[0]: Previous Sleep Cause: 5
    10/13/13 8:45:44.000 AM kernel[0]: The USB device BRCM2046 Hub (Port 1 of Hub at 0x5a000000) may have caused a wake by issuing a remote wakeup (2)
    10/13/13 8:45:44.000 AM kernel[0]: The USB device Bluetooth USB Host Controller (Port 1 of Hub at 0x5a100000) may have caused a wake by issuing a remote wakeup (3)

  • Lenovo Yoga 13 Airplane Mode not working

    Hi I recently did a fresh install of windows 8 on my yoga and I've installed all the drivers on Lenovo's website.  Most of the things are working except for the airplane mode button on the keyboard.  Does anyone know where I can find the driver for that? I no longer have the drivers that came with the laptop so if someone could upload it that would be great.  Thanks!
    Solved!
    Go to Solution.

    Welcome to the Forum!
    Based on your post, I suspect you need Energy Management Driver. Please give this link a try. http://support.lenovo.com/en_US/downloads/detail.p​age?DocID=DS032254
    If it does not resolve, please post an image of the device manager.
    Did someone help you today? Press the star on the left to thank them with a Kudo! If you find a post helpful and it answers your question, please mark it as an Accepted Solution

  • Sleep mode not working in Windows 8.1 on pavilion x2 11-h010ca

    Hello,
    I've done 2 fresh installs from the HP recovery, then upgrading to 8.1 with all patches, but this hasn't helped.
    What I've discovered is this:
    - Using the standard Windows video driver:  the machine will sleep and resume properly, but I cannot control the brightness (it's always 100% bright).
    - If I install the Intel driver from the Intel site (or HP's site), I can control brightness. When I put the machine to sleep, then resume, it crashes. It takes a few tries to bring it back up, but it always does a full restart. 
    I've installed all the latest updates through the HP tools on here, but hasn't helped in any way.
    Help on this would be great.. Thanks.

    That doesn't seem to help at all. Symptoms are the same - When I press the power button to bring it out of sleep, it buzzes briefly and the screen stays black.

  • After ram upgrade automatic sleep is not working anymore

    Some days ago I installed a second 1GB ram module in my 20" Intel iMac. After this I noticed that the automatic sleep do not work anymore. The display turns off but the iMac not. The iMac makes sounds like he wants to do to sleep but could not.
    I tried everything I could find... delete OS X powermanagement prefs, run Onyx, reset the SMC.
    Do anyone have an solution for this?
    Thanks

    Does your iMac recognize the new memory module?
    Yes.
    You might try reseating the module in its slot, and it
    would not be a bad idea to run Hardware Test from
    your install/restore DVD, just to be sure there is
    not an underlying hardware problem.
    Already done - no problems reported
    Is your new memory module of the same specifications as the
    stock module?
    Yes it is the same, I had a look on this before I bought it because I wanted to use the dual-channel mode.
    Also, what are your settings for sleeping your iMac?
    5 min to sleep display, 10 min to sleep the mac
    One other thing you may wish to
    try is updating your system of OS X 10.4.6 (your
    profile indicates that your a running 10.4.5).
    Was updated to 10.4.6. I just forget to change the forums pref
    I more thing to mention when I start the sleep mode manually everything is fine. I also tried to disconnect all external USB/Firewire hardware and tried it with a fresh mac os install on my USB HDD.
    Nothing helped.
    Thanks

  • Sleep Button Not Working on iPhone 5

    Sleep button not working .. Advice on what Else I should do?
    I've already turned it off & turned it on, & rebooted it.
    I've had my phone since October and this is the first time it's done this

    Morning AskVictoria95,
    Thanks for using Apple Support Communities.
    Installing the latest version of iOS may resolve the issue.
    For more information on this, take a look at this article:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Sleep/Wake button will not lock or unlock iPhone
    To lock the phone, press the Sleep/Wake button. Note: By default, if you don't touch the screen for a minute, iPhone locks automatically.
    To unlock iPhone, press the Home button or the Sleep/Wake button, then slide the slider.
    If either of the above steps don't work, try turning iPhone off and then on again.
    If the iPhone will not power off, reset it.
    Try to lock or unlock the phone.
    Issue not resolved
    http://www.apple.com/support/iphone/contact/
    Best of luck,
    Mario

  • I purchased I phone 5 from USA covered under Apple care  . I'm in India now. Wake/sleep button not working. Apple care here have refused to replace or repair it though it is still under international warranty. Feeling harassed. Can some one help.

    I purchased I phone 5 from USA covered under Apple care  . I'm in India now. Wake/sleep button not working. Apple care here have refused to replace or repair it though it is still under international warranty. Feeling harassed. Can some one help.

    Is there an "APPLE STORE" in India or you just went in a reseller store?
    There is a replacement program for sleep/wake button for free. Just look for an Apple Store and make a reservation at Genius Bar.
    I have an iPhone 5, bought in Dubai U.A.E.
    It is a US model (model A1428) which is different of the model use here in Italy/Europe
    My serial number is qualified for battery replacement program.
    I thought the Apple Store wouldn't repair my phone because I bought it from another country , a different model and it is already out of warranty.
    The Apple store's staff just checked if my iPhone's serial number is eligible for the program and he replaced the battery for free today.

  • Anyone had issues with on/off sleep button not working anymore

    Anyone had issues with on/off sleep button not working anymore?

    If there is Warranty or AppleCare make Genius reservation or set up Service and take or send to Apple for resolution. If no coverage, use virtual Lock Button, tap Settings App > General > Accessibility > Assistive Touch > ON > tap new white screen button > Device > Lock Screen. This can even turn OFF iPhone. To turn ON, connect iPhone to power, charger or USB of computer.

  • Widgets on my desktop using dev-mode not working in Lion

    I'm trying to get iStat back ontop of my desktop like I had in Snow Leopard. Dev-mode not working to bring widgets forward anymore. Any Ideas how to do this in lion? In Snow Leopard it was defaults write com.apple.sashboard devmode YES now that isn't working.

    When I connect my MBP (mid 2010) to iMac 27" (mid 2010), via Mini DisplayPorts, after pressing Command+F2, iMac screen went "blank" while MBP screen stays "blue" for few seconds and went back to normal. How to solve this problem?

  • Blue screen on start up. Safe mode not working?

    Blue screen on start up. Safe mode not working, any suggestions?

    Thank you, I had forgotten about target mode. I was able to back up all of my files. I also copied some additional 50 GB of files of the disk as a stress test and the hard drive worked fine and quick (and because it was quicker than retrieving the same files from a network drive to my desktop).
    I was hoping to also unpack the Applejack files on my desktop and put them back so I could run them in single user mode without running /etc/rc. However I haven't been able to get my Linux desktop to mount the iBook in Read-Write instead of Read-Only yet (I don't have access to another Mac at the moment).

Maybe you are looking for