Lenovo s820 battery consumption by radio

My s820 suddenly started to consume too much of battery. on checking battery consumption hardware is showing around 49% used by radio. I never use radio still all the time hardware shows radio consuming battery for all the hours phone is on. I have done everything including factory reset but problem is sill unresolved. please help. 

Hi
''on checking battery consumption hardware is showing around 49% used by radio. I never use radio still all the time hardware shows radio consuming battery for all the hours phone is on.''
 Dosen't refer to the FM Radio ! That is the radio the cell phone uses for phone calls and data, it has to be on. If you turn it off (put the phone in Airplane mode)you will not be able to receive/send phone calls or 3g data.If you do not expect to use it for phone calls or 3g data, you can turn it off (Airplane mode) and use wifi just for data. But text messages, 3g data, and phone calls will not work.
Hope this helps.
Regards.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as ''ACCEPT AS SOLUTION"! 
Unsolicited PM's will not be answered! ....Please post your question/s in the appropriate forum board.
English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

Similar Messages

  • Lenovo s820 top power button area hot when charging battery

    Hi there, im new lenovo user. I found that my lenovo s820 start to hot at its powerbutton back side near camera. It is normal for this phone? any comment will be appreciate. thank you.

    same on my phone why is this happen?.. :3 make me fear, and now i cant charge at all. arrghh

  • I brick my Lenovo S820 :(

    Hi, I bought a new Lenovo S820 and I wanted to upgrade FW cause my phone was without GSM signal (bad modem firmware probably).. So I installed MobileUncle tools, flashed a new recovery, rebooted phone and from that time I have a boot loop. Just Lenovo logo for few seconds, reboot, again logo.. infinite loop. I tried connect my phone for flashing in SP tool, so I push volume up, without battery and on USB, device is found in my laptop, but after few seconds it disappear from system, so I cant install drivers, flash device, anything.. I do not know, what I can do more.. Factory mode is full in chinese and nothing what I do there helps. Recovery doesnt work. Please, any advice? 
    Solved!
    Go to Solution.

    Hi, ok, so for someone in future with similiar problem
    1. power off your phone (put off battery and put it back)
    2. press power+volume down = you will see META MODE status
    3. connect USB, install USB driver -  MediaTek DA USB VCOM Port
          . in case of Windows 8.1 as my case you have to > win+c > settings > change PC settings > update & recovery
            > reboot to recovery settings and there allow (choice no. 7) unsigned drivers
    4. disconnect phone from USB, turn it off (batery out-in)
    6. download official ROM data
    5. run SP Tools, check DA DL check sum, select from unziped ROM datas scatter file, select in the window bellow all values and where is not path, click on the name of value and find file in ROM files
    6. click on download, wait until status in status bar (on the bottom) will  "Searching" and then connect device (which is still powered off) 
    7. wait for green pop up windows - success
    8. unplug phone, now you can turn it on.. done
    In additional you can via SP tool install recovery and then via recovery (power button+vlmup+vlmdown) install zip file with custom rom. 
    Good luck.

  • Lenovo s820 not recognized in computer

    I am using lenovo s820 for the past 1.5 years. Recently I upgraded it to KitKat OS and post which I'm not able to connect it to computer. Though the usb cable if fine, cell is not recognized by any computer. 
    I've tried other cables as well as with other systems also but no luck.
    Sumit

    Try doing the Reset part of this procedure
    http://support.apple.com/kb/ht1430
    If the battery is weak, you may want to do the Reset while it is connected to your computer running iTunes.  What you need is for iTunes to recognize it and do a Restore.  That will erase the iPod, re-install its software, and set it to default settings.
    Having the SIM card in there should not matter for doing a Restore.
    Also, the process that allows iPhones to run on a different wireless network is called "unlocking" not jail-breaking (which allows software that is not from the App Store to be installed).  Unlocking should do no harm.  The problem is probably the current state of the iPhone's software not allowing it to start up and run properly.  A Restore should fix it, if software is the problem.

  • Battery consumption in power supply operation

    Hello there.
    i have a Problem with my MacBook Pro 15 i5 using Windows 7 with Bootcamp:
    If i start my Mac with Windows 7 ( Power Supply and FULL Battery ) and start play a game ( for 2 or 3 hours ) the Battery is almost empty (Windows Info: "Power Supply Operation - Battery charing - 15% left") after quitting this game. So my Macbook has a Battery consumption during power supply operation. Why my Macbook is using the Battery instead of Power Supply ?
    If i use Mac OS i dont have this problem. Just with Windows 7.
    Why the Battery is almost empty after playing a game although i used Power Supply ?
    Any ideas ?
    Thanks

    no ideas ? i really need help !

  • HT1222 Has anyone else noticed much greater battery consumption since iOS 5.1.1 update for iPhone?

    Since iOS 5.1.1 update has anyone else noticed a much greater battery consumption on all fronts? My phone used to rock steady all day and know is around 47%  12 noon to 1 pm with the same amount of usage.

    Heres a support question... how the **** do I fix the dramatic battery drain problem that came about after installing 5.1.1?  Suggestions for fixing problems on iTunes did not work.

  • Bluetooth Mighty Mouse battery consumption

    I have a Bluetooth Mighty Mouse and have had it for 3 months (Christmas present). Last week, I noticed one bar had disappeared in the mouse battery life window in System Prefs - "wow" I thought "only lost 20% charge in just under 3 months".
    However, yesterday, I got a "Low Battery" warning and noticed that only two bars were remaining. A couple of hours later I got a "Critical battery level" warning and only one bar remaining.
    I don't use my mouse all that much - probably at most 6 hours per day (in short-ish intervals, turning it off in between) and I can't remember accidentally leaving it on. I'm using it with the two original AA batteries it shipped with.
    Is this normal battery consumption? I find it strange that from "Low battery" to "critical battery" would be a couple of hours and that it would suddenly lose almost 50% of its charge in a week.
    Do these mice eat AA batteries? Is it a good idea to get some rechargeables to use instead?
    Cheers for the help

    Hello thomasp:
    In answer to your question, the battery life of a wireless mouse is mostly dependent on usage. When not in use, the wireless devices go to a very low power mode. IMHO, it is a waste of time to turn mice/KBs off. I would postulate that your experience is about normal.
    I use rechargeable batteries (2500 mAh) in all my wireless devices. They do not last quite as long as the Lithium batteries - they have a lower voltage. However, I use an Energizer recharger that recharges batteries in 15 minutes - very little waiting time. In addition to being less expensive in the long run, rechargeable batteries are environmentally friendly! I bought a bunch of them on eBay. By the by, the rechargeables lose some charge every day - even if they are not in use.
    Barry

  • Can't use WIFI and the battery consumption goes much faster

    I can't use WIFI after my iphone4s was updated to ios6.0  and the battery consumption goes much faster, how to solve ?

    This seems to be a problem relatet to the current versions of the app. After uninstalling Spotify I installed an older version, 2.8.0.1081, which worked perfectly with wifi. No newer versions seem to work so I hope there will be a fix soon. I've tried changing the UPnP as well as NAT filtering settings, but the newer versions of the app still wont work.

  • Lenovo s820 Signal lost and often shows Roaming even in Home network

    Hi,
    From past 1month I am facing issue with the signal strength and calls automatically get disconnected while talking and it often shows roaming even though I am at the Home network. Pls help.
    Earlier I thought the issue is with the network provider but later I found that the SIM works good in other Phones issue is with my Lenovo S820.
    My Version information:
    Model Number : Lenovo S820
    Android Version: 4.4.2
    Baseband Version: S820.ROW.V104, 2014/11/21 10:59
    Build Number: S820_ROW_8G_S222_141121

    can any one reply

  • Lenovo S820 problem in call with bluetooth headset

    Hello All.
    I have Lenovo S820. I update smartphone to last version firmware. Information from phone:
    Model: Lenovo S820_ROW
    Android system version: 4.2.1
    Firmware communication module: S820.V21, 2013/08/07 15:14
    Build number: S820_ROW_S119_130922
    I also connected the bluetooth headset. In the phone attached 2 sim: MTS(3g and 2g), BWK(only 2g)
    Problem:
    When I call from first slot of sim with bluetooth before whistles Lenovo S820 activate flight mode and disconnect with all providers(MTS and BWK) and after reset call Lenovo S820 turn off flight mode.
    In second phone I recive call, but I can't answer a call from Lenovo S820.
    I try from different headsets. this problem occur with all headsets.

    try to update your firmware with the latest ROW version
    [#Update]#Lenovo #S820 with the Latest ROW Version Firmware S221
    http://bit.ly/1wPlj9V
    Lenovo Guide and Blog http://bit.ly/1hZlF2p

  • Lenovo S820 Firmware update error

    Hi
    Today i tried to update my Lenovo s820 firmware : S820_ROW_8G_S221_140730_TO_S820_ROW_8G_S222_141121 (222MB)
    After complete download i faced error while updating.
    Can anyone faced same issue and whether it got rectified?
    Thank you

    I suggest to use Lenovo Smart Assistant (desktop client) to help updating your phone version if you couldn't do it from the phone.
    http://support.lenovo.com/us/en/products/phones/vibe-series/vibe-z2-pro/downloads/DS101291
    WW Social Media
    T61, T410, x240, Z500, Flex 14
    Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    Follow @LenovoForums on Twitter!
    How to send a private message? --> Check out this article.
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Lenovo s820 - not working after flash

    Hello.
    I wanted to flash rom via sp flash tools. Got some problems before with flashing right one - i looked over the internet and tried some, but non wanted to flash. Then i found rom row s137 from here (http://www.indragunawan.com/2013/09/installing-miui-v5-rom-on-lenovo-s820.html) - it flashed - whole process like in all tutorials. Then i wanted to get inside cwm recovery - but new error appeared - s_ft_enable_dram_fail (4032). After few more tries (cuz tut said that i shouldnt turn on before doing it) i wanted to turn on phone just to look if its working - it didnt.
    For now ive tried i think all roms from needrom.com and from this forum - i dont know what to do... Thats my gfs phone and i wanted to make it without all those funny chinese symbols - wanted to flash miui... And even if i plug in charger - it doesnt light up to this funny red light... enev turning with vol up or down does nothing...
    Can i do anything with it?
    ps. i think that my computer does have problem with recognition what is that device i conect while i want to flash threw sp tools - so thats why i have all the time the same massage - but thats only what i think - ive tried even other phone drivers - nothing... :<

    Your question might be best answered by contacting Lenovo Support directly.
     English and Hindi
    (Primary) 1800-419-7555 (Tata) (Secondary) 1800-3000-5366 (Reliance)
    10:00 - 19:00 Monday - Saturday Except Holidays
    For Email support....  http://support.lenovo.com/in/hi/emailformforpc
    Owner & Operator of the following:
    ● Lenovo Ideapad Z570 w/ Win 7 & Win 8.1 Dual Boot ● Lenovo Yoga 3 Pro w/ Windows 8.1 ● Toshiba A75-S206 w/ Win 7
    ● IBM Thinkpad T-23 w/ Win XP ● IBM Thinkpad T-22 w/ Win XP • As well as multiple desktops dual/triple booting XP, Vista and Win 7.
    ★ Find a post helpful? Thank that member by clicking on the ☆Star☆ to the left awarding them a Kudo.
    ★ Posting a problem and a reply is helpful and it answers your question, please mark it as an "Accepted Solution"
    ★ I'm not a Lenovo employee, just a volunteer geek who likes to help folks. Enjoy your time here, pay it forward by helping others !
    ★ Sorry, I don't answer questions via Private Messages. Posting in the appropriate forum is the best way to get assistance.

  • Genuine Lenovo Replacement Battery Does Not Charge

    After reading the number of people on this forum who experienced the same problem I faced (my T61p 9 cell battery went from fine to dead overnight), I took the advice of the contributors and purchased a new, genuine Lenovo replacement battery from a seller on e-bay.  I compared the new battery to my original battery and here's the test results for each of the 2 batteries;
    Lenovo ThinkVantage Toolbox Log File
    Tuesday, September 21, 2010 11:01:04 AM
    Main Battery (Original Battery)
    Battery Name:  92P1133
    Manufacturer Name:  Panasonic
    Manufacture Date:  07-13-2008
    First Used Date:  07-26-2008
    Type:  LION - Lithium Ion
    Bar-coding Number:  1ZET587D0B7
    Battery Serial Number:  370
    Designed Capacity Percentage:  89
    Current Charge Percentage:  0
    Current Charge:  0.00 Wh
    Full Charged Capacity:  74.39 Wh
    Designed Capacity:  84.24 Wh
    Voltage:  10.13 V
    Temperature:  34 C
    Cycle Count:  219
    Battery Status
    Test Started: 9/21/2010 11:00:15 AM
    Warning Message:   The battery was completely discharged and needs to be recharged.
    9/21/2010 11:00:16 AM Test Finished:  Warning 9/21/2010 11:00:21 AM
    Lenovo ThinkVantage Toolbox Log File
    Friday, October 15, 2010 11:17:30 AM
    Main Battery (New replacement battery)
    Battery Name:  42T4619
    Manufacturer Name:  SANYO
    Manufacture Date:  03-25-2009
    First Used Date:  10-14-2010
    Type:  LION - Lithium Ion
    Bar-coding Number:  1ZFAS93S5PU
    Battery Serial Number:  7410
    Designed Capacity Percentage:  100
    Current Charge Percentage:  24
    Current Charge:  20.56 Wh
    Full Charged Capacity:  88.50 Wh
    Designed Capacity:  84.24 Wh
    Voltage:  11.03 V
    Temperature:  28 C
    Cycle Count:  0 
    Battery Status
    Test  Started  10/15/2010 11:15:21 AM
    Test Finished:  Passed 10/15/2010 11:15:22 AM
    After charging the replacement battery overnight, the battery gauge never went above showing 24% charged.  I unplugged the AC adapter and it went from 24% to its current level of 5% in about 15 minutes.  After plugging the AC adapter back into the computer, the battery will not charge.
    Any advice would be greatly appreciated.
    Andy

    It is hard to be sure without seeing it, but best guess is that the battery charging circuitry on the motherboard has died. If you still have remaing warranty, now is the time to use it.

  • Lenovo S820 dead cells-warranty

    Hi, I am having 5 dead cells on my Lenovo S820 in 6 months after purchase. Will this come under lenovo warranty?

    I got mails that they are working upon it but as the service center informed me of my phone repaired I just checked it but it was the same my problem is yet not resolved and as they say is under process. I strongly recommend you not to take lenovo phones because primarily they are perfect but as soon as they lead you to service center you will be annoyed with them..!!

  • Lenovo S820 not catching GPS Location - 4.2.1 OS

    Hi,
    I bought Lenovo S820 a month ago, I am trying to get the GPS location and it is ot catching the location in any of the application. Even I have the problem that when the device goes to standby data/wifi connection will disconnect and I'll not recieve any instant messages from any of the apps like whatsapp or wechat. Please help

    This is being addressed in another thread:
    http://discussions.apple.com/thread.jspa?threadID=2672954&start=0&tstart=0
    Unless Apple moves on this, I think 3G map users are in a world of hurt. A temporary work around is turing location services off, which is totally contrary for the maps app being a GPS but at least the keyboard doesn't freeze and you can get directions and search.

Maybe you are looking for

  • How do you monitor a background thread and update the GUI

    Hello, I have a thread which makes its output available on PipedInputStreams. I should like to have other threads monitor the input streams and update a JTextArea embedded in a JScrollPane using the append() method. According to the Swing tutorial, t

  • Abstract method in constructor

    Hi! This is simplification of my 'problem'. I solved it by more clear approach but I still don't understand the result. Output is: true, false, true. I would expect true, true, true. I use Mac Java 1.4.1. public class TestAbstract { public static voi

  • Transpose in oracle 10g

    I am having situation in my project in which I need to transpose the data, means need to display all rows to column. Please asap help me on this. Thanks in advance Anup

  • Problem with one table taking a long time to query.

    We have one table with around 6000 rows and 30 columns. It has 1 primary key, 5 indexes, 2 foreign Keys select primarykeycolumn from table it takes 0.003 seconds. If we add a where clause on an indexed column it takes 0.003 seconds approx. If we add

  • No fax number could be determined for partner

    Hi, I received this message when I was trying to see output type after creating, saving sales activity (VC01N), then come back to this sales activity > Goto> Output. My output type is not shown here. So I went to Determin Analysis, I found 3 messages