Lenovo T500 PC with SLOW CONNECT & Cause Crash of Router WRT54GX4

New Lenovo T500 laptop with Intel Wireless WIFI Link 5300 runs half as fast as my other laptops. Have Comcast high speed thru Motorloa mdem via my LynksysWRT54GX4 .
Other laptops (Old Acer, new HP) connect/run at 18,000+ kbps, while my destop harwired to modem (Old Dell) runs 30,000+ kbps.
Lenovo runs 7000-8000 kbps.
ALSO the T500 will intermitantly causecut off the Lynkys roeuter requireing complete shut dowjn and re-boot...
Is there a firm ware update for my Lynksys I can access?
Tried online download for firmware for WRT54GX4 but gave me a file with and .ibx extension that I cannot open!

Please don't try to open the file...Follow these steps to upgrade the Firmware on the router : Make sure that the computer that has the firmware file is hardwired to your router...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...
Then, unplug the power keep holding down the reset button for another 30 Seconds...
Plug the power back in, and keep holding down the reset button for 30 Seconds...
Release the reset button....Now re-configure your router...

Similar Messages

Yet another BtBroadband user with slow connection....

Hi all.
I've been having this problem for over a month now. Just before xmas our internet connection went down.
I phoned Bt, went through all the usual tests to be told there was nothing wrong with them and it was my equipment. Ok, no problem, I went out and bought a new router, got it home, plugged it in, still no internet.
Phoned Bt again, spoke to different person at callcenter, went through all the usual tests to be told that, yes, there was a problem with the line and to give it a few days for them to sort out. I gave it a few days and, amazing, the internet came back on. Problem was it was very slow. Ok, I thought, new modem, fixed connection, maybe I need to give it a few days to speed up. It's been a month now and it's gotten slower. So slow infact that when I ran the Bt Speedtester it said that my download speed was 59kps. This was the same speed I was getting back in '97 with my old dial-up modem (ah the memories...).
Anyway, called Bt again, explained all the above and was directed to thier online guide for improving the connection speeds, not very helpfull. Prior to the line problems in december, I was getting speeds up 21000kps. The line was rated for speeds between 4000-21000kps. My property is less than a 1km from the exchange, my router is connected to the main socket and I didn't have any problems prior to the line problems last year.
I have been searching through the previous posts on this forum and can see many other people with similar issues. One post stated that, because of thier line problems Bt had downgraded thier bandwith while the problem was dealt with, but had forgotten to increase it back to normal speed once it had been sorted.
This could be the issue with my connection and if any of the moderators are out there, could this be looked into, it would be deeply appreciated.
My Btspeedtester results and modem stats are as follows:
Download speedachieved during the test was - 59 Kbps
For your connection, the acceptable range of speedsis 100-250 Kbps.
Additional Information:
Your DSL Connection Rate :286 Kbps(DOWN-STREAM), 888 Kbps(UP-STREAM)
IP Profile for your line is - 135 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 0.64:11.33:89.14 (SBE:NBEBE)
These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
Upload speed achieved during the test was - 728 Kbps
Additional Information:
Upstream Rate IP profile on your line is - 888 Kbps
Router:
Type    Interleave Path
   Status    SHOWTIME
Downstream    Upstream
      Data rate(Kbps)
286Kb    888Kb
   Noise Margin
21    14
   Output power(dBm)
0    257
   Attenuation(dB)
21    7
I hope someone can help. Thanks in advance.

"If line instability is shown to stabilise normally the exchange equipment will remove the banding however on some occasions it does not release,and bt can release it manually but they like to see hub stats that show that during the line has been stable for a minimum of 5days but 10 is prefered" I'm not sure whose brainwashed you with this stuff, however. FaCT: BT retail complain to BTw about stuck banded profiles, and yes they can reset the INP, but if the line characteristics don't improve, it goes back to where it was. They also operate to strict protocol, and don't put lightweight preference on whether its seen a fixed rate at 5 days or 10. Truth is if the line is seeing high noise margin and not improving, it has a problem, and often can't be fixed, or take advantage of 21CN. Or sometimes it can be fixed, by the customer, if they choose to, or are capable of. It's not in BT's remit to fix home induced noise, but it is for the line, if its possible. They (BTw) can change any workiing parameter they see fit on DLM, but the main reason for it, is to run in AUTO. In other words, they don't do it for all and sundry, or at the drop of a hat, without good reason. Hence, they don't set "preference" for seeing stable connections. They tend to let the physics do its job.
Click the star if my posts have helped.

Rent Movies, Even With Slow Connection?

With the new Apple TV, is it possible to rent Movies even if you have a really slow (e.g 0.5Mbps) internet connection?
If you start a rental in the morning, and leave it downloading all day, will the Apple TV automatically use its 8GB of cache to store the file so that it will play continuously from start to finish, without needing to stream?

Reuben Feffer wrote:
With the new Apple TV, is it possible to rent Movies even if you have a really slow (e.g 0.5Mbps) internet connection?
If you start a rental in the morning, and leave it downloading all day, will the Apple TV automatically use its 8GB of cache to store the file so that it will play continuously from start to finish, without needing to stream?
Funnily enough I've not rented anything on it yet, but I firmly believe it will load the whole movie into the solid state buffer. If it did not do this people would be very frustrated if they decided to go back a couple of chapters after the phone rang for instance and they forgot to pause.
Until I try a rental I can't say for certain, but it would seem quite illogical (which is no guarantee) not to store the whole rental on the unit to allow for predownloading on slower connections but also for replay and chapter selection/skips/ff/rw purposes during the rental playback period.
The big unanswered question for me (maybe someone else has figured out by now) is how the 8GB of solid state memory is dished out and what purges existing content in the solid state memory.
For example - a single HD rental should fit in that 8GB, possibly two. However say the user has 2GB of photos streaming, do they have priority for memory usage ovr rentals or vice versa? The iPad has a 16GB limit for photos (or did in older OS), even on a 32GB/64GB machine, so maybe only 1-2MB is reserved for photo caching on ATV2, maybe the whole 8Gb is available, who knows?
Certainly local media from iTunes seems to cache to the unit, and quicker than ATV1, so the danger if the memory management is illogical is that any activity you do while caching an HD rental could potentially flush the cached rental in order to play the local media, but this would be daft and I hope they would reserve enough solid state memory for the rental and force the local media to cache in a smaller segment even if it meant repeatd cacheing to watch the whole thing (done transparently to the user).
What if you rent two HD movies?
Does the first download to the cache then the 2nd?
Do they download concurrently?
If they're too big for 2 in the cache does 1 of them flush the other rental out to maker room?
IMO this is all a bit vague and unpredictable.
Message was edited by: Alley_Cat

Intermittant problems with slow motion and crash of Premiere Pro

Many complain about Premiere Pro's instability.
Since a couple of days I have the same problem. Every time I want to navigate from A to B, Adobe seems to either introduce a severe SLOW MOTION effect on it's own accord, that I never put in !!!, or it just CRASHES with an error message along the lines "Problem, Try again" or similar.
This is utterly frustrating !!! I have been trying for over 6 hours today to get this remedied, but no luck.
Looking back over the past days, the problems seem to have grown exponentially both in frequency and in duration.
Of course, this is not about the program, but about the Premiere Pro Forums.
Is there a 300-day refund period for Jives???
I suggest you use that opportunity Adobe. This is

OK, that makes sense.
OS: Vista 64 Business
Browser: Firefox 3.5.2 and IE 8.06
Symptoms:
1. The connection has been reset, try again. Often after 15 minute waits.
2. Nothing happens, just waiting for Adobe and even after 30 minutes, still waiting.
3. After posting, nothing happens. You press the post button, nothing for ages. You press Cancel, nothing.
4. All other pages load without problems and are responsive.
5. Top participants listing and most popular discussions are not displayed.
Do you need further information?

Downloading upgrade with slow connection

hello,
any tip to help me get my iPhone upgraded to 3.0?
my internet connexion is so slow (max rate 105 ko/s), i always get the download interrupted after 15 mn with the error 3259.
is there a way to make it last more than 15 minutes? what should i change in my connexion settings?
thank you.

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

Upgarde to Lion with slow connection

Hi
I bought a mac book pro about 1.5 month ago
and I want to upgrade to Lion now
But I have a slow internet connection
Is there another way to upgrade?
and I saw some links that said macs early has been sold can upgrade to Lion free?
Is it true?

no I'm using 10.6.8
my basic problem is my slow internet connection
and I don't like to wait more
Is there another way to download it from another place and transfer data to my mac?(some friends from another cities can download it and post it's DVD to me)
another question i had is that for me that have bought my mac less than two months ago there is a free upgrade or is not?
thanks for all friends that helped and helping

Lenovo T500 problems with Fnf3, Fnf6, brightness button and mute/volume buttons

I have done a clean install of Windows 7 and installed the hotkey driver as well as the system inter driver but these buttons are still not working.
The only ones that are slightly working is the brightness and volume buttons (excluding the mute which isn't working at all) but I am not getting OSD indication like I did in Vista.
Is it possible to fix this problem?
Thank you
-Zac

Of the drivers you mention I have the following installed:
- ThinkPad Power Management Driver (6hku06ww)
- Power Manager (7zu413ww)
- Lenovo Fingerprint Software UPEK (6hf309ww)
They appear to work well apart from switching the built in CD player on after a power down. I now have to manually eject and reinsert the CD driver to switch it on.
On My T400s I only have discreet graphics. The built in drivers for WIn 7 worked but I downloaded Intels Win 7 graphics drivers from their site.
You might also want to install the UltraNav driver and Utility.
The drivers seem stable and (mostly) working as they should so I would recommend you install them.
Mats
Thinkpad T400s, X61s, X41, 600

Battery calculating associated with slow connect to wifi?

I recently got a new battery. To my surprise and delight, it was free even though it had close to 600 cycles on it. Anyways, the new battery works great. However, since using this new battery, the computer takes like 20 seconds to find my wifi network. I notice that whenever I wake my MBP from sleep, the battery says calculating. As soon as the battery is done calculating, the airport finds available networks.
It seems like there would be a correlation between the two but I'm not sure.
any help would be greatly appreciated

My preferred wifi networks were out of order...i put them in order of which ones i use the most often and it connects right away now

Unable to obtain ip with wireless connection to Netgear WGR614 router

Pardon my ignorance, I'm relatively new to the Mac world.
I recently purchased an iMac and at the same time purchased a Netgear wireless router.
When hardwired to the Netgear, I have no issues. I tried connecting via wireless, and keep getting the self-assigned ip address. My wireless network is detected and the Airport card connects...full strength. I also have a laptop running windowsXP, and it connects with no issues.
I have tried some of the suggestions mentioned in the discussions. Power cycled the Netgear. Changed channels...from 11 to 10. That didn't help so I went back to channel 11. I have security disabled...trying to keep the configuration as simple as possible until I can get this working.
If anyone can share some thoughts/ideas, it would be greatly appreciated.
Thanks.
-Tim

I had to go into /Library/Preferences and dragged SystemConfiguration to my desktop. I restarted the iMac.
After it booted up, I went into System Preferences => Network; created a new Location and used the "Assist Me" tab at the bottom. It walked me through setting up the Airport again and this time it worked.
For anyone that does this, once you confirm your wireless connection is working, take the SystemConfiguration on the desktop and drag it to the Trash.

Error playing movie on slow connection

I get the following error when I load a movie with slow connection:
Cannot read property 'symbolData' of undefined
I've managed to find the cause:
Movie_edgeActions.js file is invoked with autonomous function as soon as it loads. Unfortunately, the Movie_edge.js file is usually much bigger than the edgeActions file (we're talking about dozens of kbs for the edge file compared to 3, maybe 5 kb for the edgeActions file). So on slow connection, the actions file is executed before the edge file is even loaded into the browser.
Very easy to simulate:
Open the movie with fiddler running as a proxy.
Use fiddler "simulate modem speeds" and "Disable Caching" options (Rules->Performance).
I think it's a serious bug. It's very likely to happen when surfing on 3G...
Until it is fixed (I'd love to have a due date estimation), I'm planning on manually changing the autonomous function call, and call it myself when both files are loaded. I'll try to cope with it myself, but if anyone has already done it, or know how I should do it, I'd be happy to get some guidance.
Addition: I've changed the anonymous function to a named function and I call it on AdobeEdge.bootstrapCallback (I did something similiar to this post).
It works great with normal connection, but on slow connection the callback is never called. Moreover, I see the edge.js file being transfered on fiddler with http status 200, I also see it in chromes network monitor with status 200, but it doesn't get added to the scripts list on chrome developer tools. So I think the problem is actually in the preloader itself. I'll try working around it somehow...
Last thing regarding performance - is there a plan to include in the publish an option to create the entire movie (preloader, actions and edge) as a single minified js file?
We have an implementation that coordinate 5 different movies, which implies loading 15 different js files (or at least 10, because I can integrate the preloaders into my own js file). As you probably understood, on 3G it can mean lot of times until the entire application is loaded.
Thanks,
Lior

EDIT: I reverted the changes in the actions file (it works also with autonomous function).
The AdobeEdge.yepnope.errorTimeout is declared inside AdobeEdge.requestResources function in the preloader, so I declared this function in my main html, so it won't be overriden by any of the generated preloaders
What do you mean "so I declared this function in my main html".
Can you help me by providing samples of your code? This errorr is pissing me off!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Cheers.

Replication problems with slow ( 20kB/s line)

Yesterday we noticed on our production database that replication did not run anymore because of an error in one record. This forced us to re-iniitalize the subscription. Maybe this is exactly what we should not have done but we did . The result was that
production stopped because of the first part of the replication to dump all the tables and make new empty ones. The problem is that this does not seem a good idea for a slow connection between 2 machines. Better would be that we could just restart the replication
from a backup but as far as I know this is not possible.
So my question is now what can we do to speed up the replication if there is no way that we can improve the line quality. (One server is in NL and the other in CN, and as everybody know there is the great big firewall in Bejing which controlls all the internet
traffic. )
Is there a way to prevent replication from emptying the tables and fill them again.
Many thanks Peter Kaldenberg

I know that probably there is a problem with our firewalls but the fact remains that we are facing with slow connections so I ques what can we do at SQL level to speed replication or better not to have to do bulk copy over the net. In-fact why does SQL not
use some kind of delta protocol. When only data is involved this should work. Of course when the layout of tables has been changed then it makes sense the tables has to be rebuild but not for data.
Maybe a solution could be to use check-sum checking and only update these records which are different and of course add the missing once.
Additional why does the replication not give information how far the bulk copy is at least then the user knows its still working. Now what ever setting I change after 10 min the replication does not give any useful information. Which results in that the
user is thinking that the replication does not work anymore.
What about 3rd party replication tools are they any better?
Peter

Countryside users let down again - slower connecti...

and ofcourse becuase we dont make enough money for them we will suffer with slow connections for ever more.
And i have bt vision, which is a joke. As soon as we want to download a movie you can forget about the connection speed. With 3 pc users in the house plus bt vision trying to download a movie I might as well be in north Africa !
my exchange is Burghill, in Herefordshire and the chances of us getting upgraded to infinity are slim to none at all.
As much as I want to complain about the service I am getting, the terms and conditions leave me snookered paying the same price as someone with a 20 mb connection and not even getting 3 mb. No one gives a **bleep** about it, and so my little rant only serves to make myself feel better by getting it off my chest lol.

Hi could you try the things listed below then someone here ma be able to advise how to improve your speed speedtest .net has been giving strange results recently I have tried it twice today and out of 4 different testers speedtest .net has shown half the speed of the others
If you post the full stats from your router
For homehub – type 192.168.1.254 into your browser
Navigate to ADSL Settings or use the A-Z at the top right of the home page and scroll down to ADSL Settings and click on it
Click on More Details and then post the full results.
And post the full results from http://speedtester.bt.com/
then someone may be able to help and offer more advice.
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Maximum length of cable when I connect a Linksys Wireless router to another Linksys Wireless router?

HI,
I have 2 router
1. Main router for connect to internet with ADSL connection.
2. seccond router for client in another room/floor.
I try to connect both router together with UTP cable CAT5e length 40m. so seccond router client can not to receive IP address form DHCP of main router but when I bring seccound router near main router it can do, then i want to know how long of cable can do when conect routers together?
thank you

That mean 100ft * 12inc * 2.54cm / 100cm = 30.48m. right, so that mean my cable length is so longer then I can not receive DHCP IP information from main router.
I understand correct or not?
thank you

EMET 5.1 crashes all protected applications on Lenovo m91p PCs with enabled VT and TxT

Until last week we successfully used EMET 5.0 on all our PCs.
After upgrading to EMET 5.1 all EMET-protected applications crash
on all our Lenovo m91p PCs when VT-d and TxT is enabled.
The protected applications do not start at all, no balloon-tip or errordialog is shown, only Eventlog shows what happened:
EventLog IE:
Faulting application name: iexplore.exe, version: 11.0.9600.17280, time stamp: 0x53f262eb
Faulting module name: EMET64.dll, version: 5.0.0.0, time stamp: 0x545ffdbb
Exception code: 0xc0000005
Fault offset: 0x000000000008bc58
Faulting process id: 0x96c
Faulting application start time: 0x01d002698f0cb97d
Faulting application path: C:\Program Files\Internet Explorer\iexplore.exe
Faulting module path: C:\Windows\AppPatch\AppPatch64\EMET64.dll
Report Id: ccc2c9df-6e5c-11e4-86f2-4437e689f575
EventLog Word:
Faulting application name: WINWORD.EXE, version: 14.0.7125.5000, time stamp: 0x53745315
Faulting module name: EMET.DLL, version: 5.0.0.0, time stamp: 0x545ffd74
Exception code: 0xc0000005
Fault offset: 0x00064df3
Faulting process id: 0x18a8
Faulting application start time: 0x01d0026993d43cca
Faulting application path: C:\Program Files (x86)\Microsoft Office\Office14\WINWORD.EXE
Faulting module path: C:\Windows\AppPatch\EMET.DLL
Report Id: d196340d-6e5c-11e4-86f2-4437e689f575
Some facts we figured out:
Tested (crashing) applications for example: Internet Explorer 11, Word 2010, Excel 2010, Firefox 31 ESR, ...
OS is Windows 7 x64 SP1 Enterprise
It doesn't matter if it was an upgrade from EMET 5.0 to EMET 5.1 or reinstalling the PC and doing a fresh install of EMET 5.1 on a fresh machine.
Before Installing EMET 5.1 we used EMET 5.0 on the identically configured Machines (VT + TxT enabled) and there was no problem at all - the Problem is caused by EMET 5.1 and wasn't there with EMET 5.0
Problem disappears if we disable VT in the BIOS of the Lenovo m91p Machines, but this is not a Solution as we depend on using VT for virtualization-purposes.
Lenovo m91p PCs are equipped with: Intel Core i5-2400CPU, 8GB RAM, Onboard-SandyBridge Intel HD Graphics 2000, Mainboard: Lenovo IS6XM Rev.01, Intel Sandy Bridge rev.09, Intel Q67 rev. B3
Other Dell-Notebooks we use (EMET configured identically) don't show this problem, even if VT and TXT is enabled.
Basically we use the EMET Configuration "Popular Software.xml" which is included in the EMET 5.1 MSI Package, additionally we configure
DEP=ApplicationOptOut ASLR=ApplicationOptIn SEHOP=ApplicationOptOut Pinning=Enabled
and enable AdvancedRopSettings DeepHooks=True AntiDetours=True BannedFunctions=True
Additional Information:
TxT (Trusted Execution Technology) is a sub-feature of VT-d in the Bios of the Lenovo m91p PCs, when disabling VT it also disables TxT. We just figured out that we can leave VT turned on but have to disable TxT to get the machines with EMET 5.1 working
again. BUT: It's not an easy solution for us to disable TxT in BIOS on all machines. And as everything worked fine with EMET 5.0 we really think this problem should be solved by an EMET Patch.

I'm also experiencing the same issue as the OP, however I'm experiencing this on Lenovo M90p desktops with Windows 7 professional. I was previously running EMET 4.1 and upgraded to 5.1 recently. I cannot reproduce this on a Lenovo M92p with Windows
8.1 Enterprise, nor a Lenovo X1 Carbon with Windows 7 enterprise.

Painfully slow connection with new master socket

Hi forum
Hoping for some advice or perspective on possible issue with my broadband connection. Perhaps unrelated, but I recently had a new master socket fitted (NTE5), however the broadband speed in the house is now painfully slow.
Am using BT Home Hub 4, below are the rest results I'm receiving, however I'm curious as to whether 0.25Mbps really is likely to be the maximum achievable speed, as this renders several services almost unusable.
Grateful if anyone feels there is more that could be done.
Thanks,
Kevin
Results....
The only socket connected is for the router/ phone, which is now connected to the test socket (with a microfilter).
Quiet line test: normal
Speed info from the hub manager (normal socket/ test socket)
Download speed (Mbps): 0.17 / 0.24
Upload (Mbps):                0.03 / 0.02
Ping latency (ms): 326.50 / 0.00
ADSL connection (from home hub)
12:02:59, 29 Jun.
(334146.810000) DSL noise margin: 16.50 dB upstream, 10.60 dB downstream
12:02:58, 29 Jun.
(334145.900000) DSL line rate: 440 Kbps upstream, 284 Kbps downstream
Speed test (from BTW performance test)
1. Best Effort Test:  -provides background information.
Download Speed
0.17 Mbps
0 Mbps
0.25 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.17 Mbps
For your connection, the acceptable range of speeds is 0.1 Mbps-0.25 Mbps.
IP Profile for your line is - 0.25 Mbps
2. Upstream Test:  -provides background information.
Upload Speed
0.03 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.03Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps
We were unable to identify any performance problem with your service at this time.
It is possible that any problem you are currently, or had previously experienced may have been caused by traffic congestion on the Internet or by the server you were accessing responding slowly.
If you continue to encounter a problem with a specific server, please contact the administrator of that server in the first instance.
Please visit the FAQ if you are unable to understand the test results.
From kitz.co.uk max speed calculator
Estimation of your maximum rate adaptive adsl speed
Downstream
Attenuation
0 dB
Approx
Line Length
0 km
From BT Diagnostics site:
Broadband Speed Test
We haven't been able to complete the speed test at this time.
This may be due to a problem with the speed tester, or your line may be running very slowly.

Thanks for your quick response, much appreciated. Further results below - suggesting that faster should be possible?
The connection time from 12 was due to a manual reset, the only time it was reset (WAN logs also noted below).
ADSL Checker....
Telephone Number 01562xxxxxx on Exchange WOLVERLEY is served by Cabinet 3
Featured ProductsDownstream Line Rate(Mbps)Upstream Line Rate(Mbps)Downstream Range(Mbps)Availability Date
WBC ADSL 2+
Up to 13.5
11.5 to 15
Available
WBC ADSL 2+ Annex M
Up to 13.5
Up to 1.5
11.5 to 15
Available
ADSL Max
Up to 8
7 to 8
Available
WBC Fixed Rate
2
Available
Fixed Rate
2
Available
Other Offerings
Copper Multicast
Available
12:02:59, 29 Jun.
(334146.810000) DSL noise margin: 16.50 dB upstream, 10.60 dB downstream
12:02:58, 29 Jun.
(334145.900000) DSL line rate: 440 Kbps upstream, 284 Kbps downstream
12:01:36, 29 Jun.
(334063.890000) DSL is down after 2226 minutes uptime
12:01:36, 29 Jun.
(334063.890000) ETHoA is down after 2226 minutes uptime
12:01:36, 29 Jun.
(334063.550000) PPPoA is down after 2226 minutes uptime [Waiting for Underlying Connection (WAN DSL - Up)]
12:01:33, 29 Jun.
(334060.470000) PPP LCP Send Termination Request [User request]

Lenovo T500 PC with SLOW CONNECT & Cause Crash of Router WRT54GX4

Similar Messages

Maybe you are looking for