Lenovo t61 comes out of standby automatically after the lid is closed

Hi,
I have a t61 + wind 7 + 32 bit + ultimate edition. It was working fine till now and suddenly I have noticed its coming out of the standy mode suddenly. I close the lid, its going to standby mode i see the little semi circle on the top and everything is fine. Suddenly when it finds any known wifi signal or any thing, which I think I have noticed, its comes out of stand by ....I can tell that from the beep it makes and the light suddenly goes off. After sometime I notice that the battery dies,  as its in normal mode even when the lid is closed and it consumes all of the battery. Please let me know what settings have to be changed to get rid of this F error. I am facing a lot of trouble as it consumes all of the battery when I open the lid even if its fully charged. I think it has to do with some settings. I have verified everything power manager, wireless adapater etc. Any gurus pls suggest.
thanks,
Manu

a couple things you can check...
open up Device Manager and see if Allow this device to wake the computer is enabled for your mouse and/or your wired ethernet device on the Power Management tab of their Properties sheets.
hth.
English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

Similar Messages

  • What could be the possible reason for a deployed application to run slow after the target pc comes out of standby mode?

    What could be the possible reason for a deployed application to run slow after the target pc comes out of standby mode?  PC running XP and using the USB to communicate with the DAQ and driver boards.  Application generated with 2010.
    Thanks

    Hello,
    Usually default property is checked 
      system property -> devices ->usb root -> power management -> allow system to switch off device
    Hope this help
    Regards
    Tinnitus
    CLAD / Labview 2011, Win Xp
    Mission d'une semaine- à plusieurs mois laissez moi un MP...
    RP et Midi-pyrénées .Km+++ si possibilité de télétravail
    Kudos always accepted / Les petits clicks jaunes sont toujours appréciés
    Don't forget to valid a good answer / pensez à valider une réponse correcte

  • Everytime my computer comes out of standby it no longer recognizes the GPIB-USB.

    When the computer comes out of standby or hibernation I get a message saying that there is an unknown device on the USB port. Then I have to unplug the GPIB and plug it back in. Then the New Hardware Found Wizard starts up and I have to install the software again. Can this problem be fixed?

    After a bit of searching through MSDN help, I found the SetThreadExecutionState command in the kernel32.lib. If you invoke SetThreadExecutionState(&H80000001) on entry to your application, you will prevent the OS from entering standby autonomously from an idle state. A user initiated standby, though, will override this. The application should issue a SetThreadExecutionState(&H80000000) on close to ensure for good housekeeping.
    If you want the system to query the user before entering a user-initiated standby, then your application needs to intercept and respond to the WM_PowerBroadcst message fired by the PBT_APMQuerySuspend event. You will need to subclass your main application and respond to the event by returning a BROADCAST_QUERY_DENY from the wind
    ow message loop. Go to this URL for the relevant code fragment in VB: http://www.freevbcode.com/ShowCode.asp?ID=2596
    Larry E."

  • HT201177 My Macbook pro: After sleeping, the screen comes on momentarily then blacks out.  When I close the lid and reopen it the same thing happens.  The screen only does this after waking up from sleeping.  Help, thanks!

    Macbook Pro:
    When I raise the lid after sleeping, the screen comes on momentarily then backs out.  If I close the lid and raise it again, the same thing happens.  It is sometimes necessary to force quit.  Once restarted, there is no problem unless the lid is closed for a short time and the machinge goes to sleep.
    Help! Hesperia fire captain

    Hi ...
    Try Resetting the System Management Controller (SMC)

  • Draw Something causes Apple TV to come out of standby

    When starting the "Draw Something" app on my I-phone or I-pad, the start up "splash screen" seems to be interpreted by iOS as a video & causes Apple TV to come out of standby (assuming AirPlay had been left selected to Apple TV)
    I have reported the issue to Zynga, who tell me an updated version of Draw Something addresses this issue, however the version currently available on the App Store (created Dec 28th 2012) appears to be the same (problematic) version I already have.

    Sadly the suggestion you've made is where I've ended up. I'm grabbing a Belkin cable, like the one you mentioned, for $10 and calling it a day on the cable/SAT TV watching front. Because Last night, while watching the Blu-ray copy of Planet Earth, the sound from the Hi-Fi was solid and full. Even my super non-audiophile GF noticed the difference without question right away over the stock hollow LCD speakers' sound I've been annoyed by for sometime. Sound for most is harder to see a difference in when compared to the difference in Standard Source watching to HD.
    Anyhow unless someone who knows about my LCD model can help with getting it's sound to the Hi-Fi like I have the PS3 or I move on to what I think is a safe beat, a 7.1 profile HD theater surround sound system, I'll be using the Hi-Fi for my Entertainment watching till in the near future. Otherwise your last suggestion and my conclusion, the analog cables will have to do for Cable/SAT tv watching.
    Thanks for your input and time on my frivolous matter.
    Message was edited by: Johnny Neat

  • Cannot come out of standby w/ wireless keyboard mouse (usb)

    For some reason I cannot get my mega 180 to respond to keyboard or mouse activity when in standby (wireless mouse/keyboard via usb).  In ther device manager, the options to "allow this device to bring comp out of standby" is grayed out.  Any ideas?
    Something else I have noticed that might jog someone's brain:  I have a touchscreen monitor that connects via a 9 pin adapter (it is made for a serial port) to a usb port.  When I bring the computer out of standby by pressing the power button, I lose the touchscreen function, and can only get it back with a reboot.
    tia

    bios settings
    you want s3 bios to turn the most devices off.
    probable need to turn apm to disable,
    and then enable some sort of wakeup ...kbc (keyboard comand,...wake on usb or something like that.
    that worked for my msi board..yours should be similar

  • Recorded a video in portrait mode and want to switch it to landscape mode is there any way else to do it without useing quicktime pro....hope apple fixes this in ios 7 the video should come out in landscape regardless of the way you hold your phone

    is there any way else to do it without useing quicktime pro....hope apple fixes this in ios 7 the video should come out in landscape regardless of the way you hold your phone or if you start in portrait and go into landscape while recording

    You used the data.  Verizon can not see what it was sued for.  However your phone can see whats apps used the data.  go to settings-data usage- there will be a place that says data usage cycle.  line the dates up with your cycle.  then there will be a bar graph below that   extend bother white bars one all the way to the left and one all the way to the right.  after those are extended below that will be a list of apps,  there should be one that used over 2 gb and that will show you what app used that data in her purse

  • Screen doesnt get blacked out when on call after the new update

    Since the time i Have updated the firmware screen doesnt gets blacked out, when on call after the new update. Because of this option automatically get selected by getting touched cheecks.
    any solution?

    Please try to update your plugins [http://www.mozilla.org/en-US/plugincheck/] Flash is out of date.
    Also the Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
    '''Note''': ''This will cause you to lose any Extensions and some Preferences.''
    *Open websites will not be saved in Firefox versions lower than 25.
    To Reset Firefox do the following:
    '''For Firefox versions previous to 29.0:'''
    #Go to Firefox > Help > Troubleshooting Information.
    #Click the "Reset Firefox"[[Image:Button reset]] button.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    '''For Firefox 29.0 and above:'''
    #Click the menu button [[Image:New Fx Menu]], click help [[Image:Help-29]] and select ''Troubleshooting Information''.
    Now, a new tab containing your troubleshooting information should open.
    #At the top right corner of the page, you should see a button that says "Reset Firefox"[[Image:Button reset]]. Click on it.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
    Did this fix your problems? Please report back to us!
    Thank you.

  • My photos are out of chronological order after the os 5 upgrade.   How can I get them back in order?

    My photos are out of chronological order after the os 5 upgrade.   How can I get them back in order?
    If its not possible, how do I go back to the old  os?

    I had tried that several times with no luck.  Late last night I was finally able to get through  to the Verizon technical support who then called in Apple technical support.  It took 1 1/2 hours for them to figure it out and guide me through a fix.  So here's the deal .......... I use Yahoo mail and had left the "contacts" button in the on position.  Apparently Yahoo likes to go into your contacts and gather information and can leave it in shambles.  My advice is, go to settings, then mail, contacts, calendars.  Select any and all of your email accounts and go in and turn off their access to your information.  Leave it on for Icloud but none of the others.

  • I'm trying to migrate from mobileMe to iCloud but I have Snow Leopard (the latest version). It looks like Lion is no longer available because Mountain Lion comes out next month (July). The problem is mobileMe ends on June 30th. How can I migrate?

    I'm trying to migrate from mobileMe to iCloud but I have Snow Leopard (the latest version). It looks like Lion is no longer available because Mountain Lion comes out next month (July). The problem is mobileMe ends on June 30th. How can I migrate?
    My iphone and my ipad are compatible but when I try to go to icloud on my phone it says to do it on my computer.
    I would like to have my calendar, contacts, etc.. all sync like they do now. Is there a way to upgrade before June 30th? If not, will the gap be an issue or will I just be able to buy mountain lion and sync everything?
    Any suggestions?
    Thank you!

    You can buy Lion in the App Store now, but move to iCloud now. If you wait to Mountain Lion, you will only have Mail in Snow Leopard, so you will lose syncing unless you use Lion or Mountain Lion. It's up to you

  • After 10.8.2 update i can no longer wake my macbook from standby with keyboard when the lid is closed

    I just updated to 10.8.2 and now i can no longer wake my macbook froom standby when the lid is closed, it directly goes back to sleep
    steps to reproduce:
    1. attach secondary monitor and keyboard
    2. close lid
    3. wait 5 seconds for going to standby
    4. press any key on keyboard and type in user-credentials (notice how the 2nd monitor becomes the mainscreen)
    5. wait 5 seconds
    6. standby again
    side note:
    i also have sudo nvram boot-args="iog=0x0" enabled, because i like to not use the integrated screen when its attached to a secondary screen, but since it goes back to standby right after login this is pretty much pointless

    Same here, I think changed something in 10.8.2 that wrecked the "Open-MBP Clamshell Mode."  sigh

  • Append hyphen automatically after the wrapping of text in the dimension field

    Post Author: Nita_here
    CA Forum: WebIntelligence Reporting
    I want to Append hyphen automatically after the wrapping of text in the dimension field.
    e.g the text reads "I want to wrap this text". then if cell width exceeds after "I want to wrap" then it should be displayed like this "I want to wrap-" "this text".
    Thanks in advance,
    Nita

    Post Author: Nita_here
    CA Forum: WebIntelligence Reporting
    Thanks for your input.
    Let me tell you what I have understood. I will create a variable having the formula (which i have earlier written) in universe. Whenever i need to use the formula in infoview, I will call the variable instead. That's fine. But again, I will have the same problem. If I do any change in infoview level, the cell width is bound to change as it is not the free standing cell, its a column among othe one. e.g.
    A  B  C
    1  2  3
    4  5  6
    (you can think B as the column). Any change(addition, deletion of columns) will certainly change the cell width of B. So, again I need to calculate the things, which i dont want.
    Nita_here: I manually calculated that after 12 characters, the cell wraps the text.
    I wonder if there would be a way to do the things dynamically.
    Thanks in advance,
    Nita

  • Ipod touch 4g - sound comes out one earphone loud and the other softly. I've tried other headphones with same result. is there a fix for this ?

    Ipod touch 4g - sound comes out one earphone loud and the other softly. I've tried other headphones with same result. is there a fix for this ?

    Clean out/blow out the headphone jack. Insert/remove the heaphone plug a dozen times or so
    Try the following to rule out a software problem:
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>GeneralReset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store since it appears you have a bad headphone jack
    Apple Retail Store - Genius Bar
    Apple will exchange your iPod for a refurbished one for this price. They do not fix yours
    Apple - Support - iPod - Repair pricing
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens

  • HT2508 My amp has an USB input but when I attach my mac pro to it, and set the input to the USB setting, no sound comes out. I looked at the system settings, but none of them produce a different outcome. How can I send the music through the USB out to USB

    My amp has an USB input but when I attach my mac pro to it, and set the input to the USB setting, no sound comes out. I looked at the system settings, but none of them produce a different outcome. How can I send the music through the USB out to USB in?

    AFAIK cameras offer their own built-in format utility for inserted SD cards.  You should use that.  Otherwise, refer to the manual that came with your camera to determine precisely how your SD cards need to be formatted to work properly.  Personally, I'd suggest Partition Scheme: MBR, and Filesystem: FAT32.
    Try to limit the number of formats you perform on the SD cards, though, as you're reducing their lifespan.  I believe formatting causes re-writes to a portion of the SD card that has fewer read/write cycles than the rest of the card as a whole.

  • Slwo to Come Out of Stand By after OS2 Upgrade

    Ladies and Gentlemen:
    Ever since I upgraded my 16 GB PlayBook to OS2, it has been very slow - sometimes up to 17 seconds - to come out of stand by.  Has anyone else run into this?  Any ideas as to how to speed things up a bit?  It was pretty well instantaneous with the previous OS...
    Thanks!

    Hello,
    after upgrading to OS2, when my Playbook goes into Standby mode, it turns OFF??
    Anyone... HELP!

Maybe you are looking for

  • Pre-plugin upgrade queries related to extractor delta

    Hi All, as part of plug-in upgrade, i'm aware that as a pre-plugin activity the delta queue has to be emptied before the upgrade(LO and 0FI_AR_3 for eg). Is it neccessary to pull in the records from datasources that uses the Delta process <b>'E'</b>(

  • Create .exe that sends results to .txt, keeps looking for folder with .exe name

    Created a project that logs the results to a .txt file that was setup in "Source File Settings" as a subfolder "Test Results",  but when I run the .exe it trys to write the results to a folder with the same name as my .exe file. I must have something

  • Problem in constraints

    Hi friends, I have a scenario in the sense, i'm a Apex Developer.......Im developing an database application in apex by using two tables.......... One table is the one that im taking from my production instance, in my scenario i have taken the table

  • COPA Derivation rule not running in background

    Hi all We are encountering a strange problem during derviation in document posting & creation of assets. We have added a characteristic value Material group to the profitability segment and have added a derivation rule in KEDR based on order. The rul

  • I cannot find any support for using templates to send to multiple addressees

    I used this system last year, but cannot find how I did it; I want to send to all people in the special address book that I have set up, but without revealing the email address of all the members to each individual. I am using Thunderbird 24.6.0