Lenovo ThinkPad T61 14,1" LCD problem

Hi, LCD in my T61 14,1" with nVidia graphics (T61 7664-18G) has failed - I attached an image. External LCD is 100% OK, just internal have this problem (like image in fog, bad readable). I try to replace LCD - problem is still there. What can be the solution? LCD cable, invertor, or it is a nVidia problem (but really just internal LCD problem)? Thanks for help.
Internal LCD (like in fog, no readable text - or very bad):
Link to picture
External LCD (vertical lines just in photo, everything is 100% OK):
Link to picture
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

xsuchy09 wrote:
Buy new/used mainboard with integrated Intel graphics (external display in dock width 1920x1200 will not be problem, second display with same resolution will be ok with intel graphic too I think, or?)? Buy another T61/T400 with Intel graphics (because of compatibility and old style keyboard) It is used only for programming, I think that I don't need graphics performance ... Are parts from T61 with nVidia graphics full compatible with parts with Intel graphics (when I will go this way I will have some replacement parts )? Or is it compatible T61 14,1" and T400 in main parts? What will be the best choice? Performance of T61 is sufficient for development of web applications etc.
If you don't need graphic performance and the T61 performance is enough for you I would buy an Intel T61 planar and replace the Nvidia one. RAM and CPU are compatible, but you will need an integrated heatsink since it's different than the discrete one you have now. I can't comment about driving two monitors, I guess you now use both VGA and DVI ports, right?
You can also re-use your hard drive or SSD and WLAN card.
If you go the T400 way (or even T410, it also has a non chiclet keyboard) you will be able to reuse the hard drive/ssd. RAM is not compatible! (DDR3 instead of DDR2)
Hope this helps!
Cheers
/L40SX/240/240X/2*340CSE/360PE/365XD/380D/380E/380XD/380Z/390/560E/560X/2*570/2*600/600E/750Cs/755C/760CD/760EL/760XD/770E/A20p/A22p
A31/i1600/G40/R50p/R61i/S30/SL510/2*T22/4*T4x/11*T6x/6*T4x0x/6*T5x0/3*W5x0/W700/3*X2x/4*X3x/3*X4x/5*X6x/3*X6xT/10*X2xx/2*X200T/4*X30x/Z60m/3*Z61x
Comunidad en Español English Community Deutsche Community Русскоязычное Сообщество

Similar Messages

Lenovo Thinkpad T61 8895WFJ Windows Vista

hello,
following problem:
Windows Vista
Hardware:
Lenovo Thinkpad T61 8895WFJ
WLAN Intel WiFiLink 4965AGN Driver: MS Ver 12.4.1.4
Software:
Lenovo Access Connections Version 5.33
On my Windows XP installation, I was in the "Access Connections" choose among authentification "Cisco LEAP."
Now I have installed Windows Vista, where there are "CISCO LEAP" no more.
thx

http://forums.lenovo.com/lnv/board/message?board.id=X_Series_Tablet_ThinkPads&message.id=3768#M3768
try the tips that is included in that link.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Lenovo Thinkpad T60 with start up problems

I have a Lenovo Thinkpad T60 with start up problems. In order to get the computer to start up, I have to unplug it, remove the battery, re-insert the battery and turn it on, once it starts the start up sequence, I can plug in the power cord.
If I plug the cord in before I push the power button, all of the lights go out, and it does nothing.
I have tried several power supplies, and a new battery, even though the old battery seems to work.
All of the updates are applied, including the latest bios update.
The computer seems to work normally unless it goes into standby, then it just turns off.
Any ideas what could be causing this?
T60, 2623 KEU, Windows XP SP3

Hello,
Did you replace the primary battery which snaps into the back, or the internal CMOS/RTC battery inside the unit?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Lenovo Thinkpad T61 Build Quality

I have a T61, and since then has been crap since I bought the LCD cover, cracking when you press, but the service could not start with him. And this is normal? What can I do? What can I do then? I am writing from Hungary.
Best of all, it is also fitting to the site was dismantled, and the bottom of the machine does not fit properly, and the Lenovo We announce that the plane could not be any paper is slid into the machine and the screen behind it, but I know to do that.
I do not want to szidni Lenovo, very love this machine and the brand, yet also got T-shirt, but somehow it does not get what I expected.
Video: http://www.youtube.com/watch?v=KFQ814Rehh4
Related forums: (I think this problem is not just me) http://forum.notebookreview.com/showthread.php?t=142781
ThinkPad X200 Tablet (7453-Y24)

pethemilan wrote:
I have a T61, and since then has been crap since I bought the LCD cover, cracking when you press,
Could you clarify exactly what you mean please. Did you replace the LCD cover, or have it replaced at some point?
It looks to me as though a wlan or bt cable hasn't been routed correctly and is causing the disformation on the cover. Normally I would suggest just to apply pressure and click it back into place, but if a cable has been misrouted during a component replacement, this would not be the correct advice.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Thinkpad T61 wireless access connection problem and heat problem

My laptop keeps heating up ALOT i've been using tpfancontrol to make my fan go really fast and to cool it down. Anyone have a clue what to do about that? It automatically sets itself to smart (fan control config). Also my access connections has been working really bad lately. It won't connect anywhere. When i press fn+f5 and click on the network i want to connect to it would show connection successful and say applying wireless settings with a x next to it. Anyone know what to do about this?! cause i installed and uninstalled and nothing is working =[. Newest access connections and updated wireless drivers. Wireless zero connection is working fine though.
Wireless Card: Intel 4965 AGN
Windows xp pro sp3
Any help would be great.
Message Edited by wwilsonxp on 01-26-2009 10:08 AM
Solved!
Go to Solution.

mind parameter ManModeExit (set to 72 degrees Centigrade in common .ini and 80 if not set by .ini) in TPFanControl.ini:
// Program exits manual mode and switches to smart mode with last chosen
// profile, if this temp (degrees Centigrade or Fahrenheit) is achieved.
// default= 80 degrees Centigrade / 176 degrees Fahrenheit.
ManModeExit=72 //ManModeExit=162 Fahrenheit
...and switch off any power saving mode of wlan device.
Message Edited by troubadix on 01-27-2009 12:33 AM

T61 Lenovo Thinkpad crashes powerpoint 2010

Just installed Office 2010 on a Lenovo Thinkpad T61 running on MS Windows XP Professional v5.1.2600 SP 3. When we open two or more presentations in PPT 2010 and try to work with them PPT crashes. Sometimes it will crash when trying to open a file. We did not have this problem with Office 2007. I read through some posts and did try disabling (renaming) the Thinkpad send to blue tooth add-in, btsendto_office.dll and also the btsendto.dll files and that did not work.
Any other ideas?

Hello,
Does the problem only occur on one ThinkPad T61? Have you tried it on another, or on different computers?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Thinkpad T61 kernel panics

I'm having some trouble with random kernel panics on a thinkpad T61. Sometimes they occur just after boot yet other times I can be using my laptop for hours with absolutely no problems before it decides to panic. I've attached a picture of the error message I get and the output of some commands I thought would be relevant.
My /etc/rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
LOCALE="en_GB.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Europe/London"
KEYMAP="uk"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
MOD_AUTOLOAD="yes"
MODULES=(e1000e snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
USELVM="no"
# NETWORKING
# Should also be put in /etc/hosts
HOSTNAME="alasdair-laptop"
NETWORKS=(ethernet gp)
# DAEMONS
DAEMONS=(syslog-ng acpid @net-profiles netfs crond @alsa)
Here's my dmesg, taken just after booting.
Linux version 2.6.25-ARCH (root@workstation64) (gcc version 4.3.1 20080626 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jul 14 15:25:51 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007deb0000 (usable)
BIOS-e820: 000000007deb0000 - 000000007decc000 (ACPI data)
BIOS-e820: 000000007decc000 - 000000007df00000 (ACPI NVS)
BIOS-e820: 000000007df00000 - 000000007e000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
1118MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00f6900] 000f6900
Entering add_active_range(0, 0, 515760) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 515760
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 515760
On node 0 totalpages: 515760
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2237 pages used for memmap
HighMem zone: 284147 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F68D0, 0024 (r2 LENOVO)
ACPI: XSDT 7DEBB77F, 0094 (r1 LENOVO TP-7L 2170 LTP 0)
ACPI: FACP 7DEBB900, 00F4 (r3 LENOVO TP-7L 2170 LNVO 1)
ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20070126]
ACPI: DSDT 7DEBBD1D, FED1 (r1 LENOVO TP-7L 2170 MSFT 3000000)
ACPI: FACS 7DEE4000, 0040
ACPI: SSDT 7DEBBAB4, 0269 (r1 LENOVO TP-7L 2170 MSFT 3000000)
ACPI: ECDT 7DECBBEE, 0052 (r1 LENOVO TP-7L 2170 LNVO 1)
ACPI: TCPA 7DECBC40, 0032 (r2 LENOVO TP-7L 2170 LNVO 1)
ACPI: APIC 7DECBC72, 0068 (r1 LENOVO TP-7L 2170 LNVO 1)
ACPI: MCFG 7DECBCDA, 003C (r1 LENOVO TP-7L 2170 LNVO 1)
ACPI: HPET 7DECBD16, 0038 (r1 LENOVO TP-7L 2170 LNVO 1)
ACPI: SLIC 7DECBDF0, 0176 (r1 LENOVO TP-7L 2170 LTP 0)
ACPI: BOOT 7DECBF66, 0028 (r1 LENOVO TP-7L 2170 LTP 1)
ACPI: ASF! 7DECBF8E, 0072 (r16 LENOVO TP-7L 2170 PTL 1)
ACPI: SSDT 7DEE26D9, 025F (r1 LENOVO TP-7L 2170 INTL 20050513)
ACPI: SSDT 7DEE2938, 00A6 (r1 LENOVO TP-7L 2170 INTL 20050513)
ACPI: SSDT 7DEE29DE, 04F7 (r1 LENOVO TP-7L 2170 INTL 20050513)
ACPI: SSDT 7DEE2ED5, 01D8 (r1 LENOVO TP-7L 2170 INTL 20050513)
ACPI: DMI detected: Lenovo ThinkPad T61
ACPI: Added _OSI(Linux)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 7:7 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 7:7 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7e000000:72000000)
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
PM: Registered nosave memory: 00000000000d4000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 511731
Kernel command line: root=/dev/disk/by-uuid/bf262041-d9e8-494d-becc-808ef613eef2 ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2094.737 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2040240k/2063040k available (2083k kernel code, 21556k reserved, 711k data, 268k init, 1145536k highmem)
virtual kernel memory layout:
fixmap : 0xfff80000 - 0xfffff000 ( 508 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc03c1000 - 0xc0404000 ( 268 kB)
.data : 0xc0308fe8 - 0xc03baea0 ( 711 kB)
.text : 0xc0100000 - 0xc0308fe8 (2083 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 4197.54 BogoMIPS (lpj=6992869)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: Checking initramfs for custom DSDT
CPU0: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping 06
Booting processor 1/1 ip 4000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4191.12 BogoMIPS (lpj=6982598)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping 06
Total of 2 processors activated (8388.66 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 1229046 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to: check_tsc_sync_source failed.
Brought up 2 CPUs
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: BIOS _OSI(Linux) query honored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x12, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Power Resource [PUBS] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
system 00:00: iomem range 0xcc000-0xcffff could not be reserved
system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
system 00:00: iomem range 0x0-0x0 could not be reserved
system 00:00: iomem range 0x0-0x0 could not be reserved
system 00:00: iomem range 0x0-0x0 could not be reserved
system 00:00: iomem range 0xe0000-0xe3fff has been reserved
system 00:00: iomem range 0xe4000-0xe7fff has been reserved
system 00:00: iomem range 0xe8000-0xebfff has been reserved
system 00:00: iomem range 0xec000-0xeffff has been reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x7dffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
system 00:00: iomem range 0xfed4c000-0xffffffff could not be reserved
system 00:02: ioport range 0x164e-0x164f has been reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x800-0x80f has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x165f could not be reserved
system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
system 00:02: iomem range 0xfed45000-0xfed4bfff could not be reserved
PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: 0xd4000000-0xd6ffffff
PREFETCH window: 0x00000000e0000000-0x00000000efffffff
PCI: Bridge: 0000:00:1c.0
IO window: 3000-3fff
MEM window: 0xfc000000-0xfdffffff
PREFETCH window: 0x00000000f8000000-0x00000000f80fffff
PCI: Bridge: 0000:00:1c.1
IO window: 4000-4fff
MEM window: 0xdc100000-0xdf2fffff
PREFETCH window: 0x00000000dfd00000-0x00000000dfdfffff
PCI: Bridge: 0000:00:1c.2
IO window: 5000-5fff
MEM window: 0xd8000000-0xd9ffffff
PREFETCH window: 0x00000000dfa00000-0x00000000dfafffff
PCI: Bridge: 0000:00:1c.3
IO window: 6000-6fff
MEM window: 0xd0000000-0xd1ffffff
PREFETCH window: 0x00000000df700000-0x00000000df7fffff
PCI: Bridge: 0000:00:1c.4
IO window: 7000-7fff
MEM window: 0xcc000000-0xcdffffff
PREFETCH window: 0x00000000df400000-0x00000000df4fffff
PCI: Bus 22, cardbus bridge: 0000:15:00.0
IO window: 0x00008000-0x000080ff
IO window: 0x00008400-0x000084ff
PREFETCH window: 0xf4000000-0xf7ffffff
MEM window: 0x80000000-0x83ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 8000-bfff
MEM window: 0xf8100000-0xfbffffff
PREFETCH window: 0x00000000f4000000-0x00000000f7ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[b] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Enabling device 0000:00:1e.0 (0005 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:15:00.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 554k freed
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS not found.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie02]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
Allocate Port Service[0000:00:1c.4:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 268k freed
ACPI: ACPI Dock Station Driver
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 16 (level, low) -> IRQ 16
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226100 irq 16
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226200 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD1600BEVS-08RST2, 08.01G08, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 08.0 PQ: 0 ANSI: 5
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1830 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1838 irq 15
ata4.00: ATAPI: Optiarc DVD RW AD-7910A, 1.D1, max UDMA/33
ata4.00: configured for UDMA/33
ata5: port disabled. ignoring.
scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7910A 1.D1 PQ: 0 ANSI: 5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
e1000e: Copyright (c) 1999-2007 Intel Corporation.
ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:19.0 to 64
eth0: (PCI Express:2.5GB/s:Width x1) 00:1e:37:d6:46:39
eth0: Intel(R) PRO/1000 Network Connection
eth0: MAC: 4, PHY: 6, PBA No: 1008ff-0ff
ACPI: PCI Interrupt 0000:00:1b.0[b] -> GSI 17 (level, low) -> IRQ 17
hda_intel: probe_mask set to 0x1 for device 17aa:20ac
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
ACPI: SSDT 7DEE1B32, 02C4 (r1 PmRef Cpu0Ist 100 INTL 20050513)
ACPI: SSDT 7DEE1E7B, 085E (r1 PmRef Cpu0Cst 100 INTL 20050513)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7DEE1A6A, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
ACPI: SSDT 7DEE1DF6, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:01 is registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [THM0] (52 C)
ACPI: LNXTHERM:02 is registered as thermal_zone1
ACPI: Thermal Zone [THM1] (42 C)
Non-volatile memory driver v1.2
thinkpad_acpi: ThinkPad ACPI Extras v0.19
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7LETB7WW (2.17 ), EC 7KHT24WW-1.08
thinkpad_acpi: Lenovo ThinkPad T61
thinkpad_acpi: radio switch found; radios are enabled
thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
input: ThinkPad Extra Buttons as /class/input/input5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 3:0:0:0: Attached scsi generic sg1 type 5
Linux agpgart interface v0.103
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001860
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[b] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: WMI: Mapper loaded
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler
ACPI: Error installing bay notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: device:03 is registered as cooling_device2
input: Video Bus as /class/input/input6
usb 1-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe226c00
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: device:08 is registered as cooling_device3
input: Video Bus as /class/input/input7
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfe227000
iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux, 1.2.23k
iwl4965: Copyright(c) 2003-2007 Intel Corporation
usb 3-1: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
hub 3-0:1.0: unable to enumerate USB device on port 1
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.0 to 64
iwl4965: Detected Intel Wireless WiFi Link 4965AGN
iwl4965: Tunable channels: 13 802.11bg, 19 802.11a channels
phy0: Selected rate control algorithm 'iwl-4965-rs'
hub 6-0:1.0: unable to enumerate USB device on port 2
usb 1-2: USB disconnect, address 2
input: PC Speaker as /class/input/input8
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
ACPI: PCI interrupt for device 0000:03:00.0 disabled
ACPI: PCI Interrupt 0000:00:1f.3[A] -> GSI 23 (level, low) -> IRQ 23
ACPI: PCI Interrupt 0000:15:00.1[b] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:15:00.1 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[f8101000-f81017ff] Max Packet=[2048] IR/IT contexts=[4/4]
Yenta: CardBus bridge found at 0000:15:00.0 [17aa:20c6]
usb 7-1: new high speed USB device using ehci_hcd and address 2
Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x8000 - 0xbfff
cs: IO port probe 0x8000-0xbfff: clean.
pcmcia: parent PCI bridge Memory window: 0xf8100000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xf7ffffff
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04791/0x300000
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input9
usb 7-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Monitor-Mwait will be used to enter C-3 state
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00061b032a26dd3a]
EXT3 FS on sda3, internal journal
Adding 891596k swap on /dev/sda4. Priority:-1 extents:1 across:891596k
Clocksource tsc unstable (delta = -297926941 ns)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 40100102, writing 40100106)
scsi 5:0:0:0: Direct-Access S31B0806 USB DISK 1100 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: [sdb] 2030592 512-byte hardware sectors (1040 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sd 5:0:0:0: [sdb] 2030592 512-byte hardware sectors (1040 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sd 5:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input10
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:1f:5b:88:6f:1f
wlan0: authenticate with AP 00:1f:5b:88:6f:1f
wlan0: RX authentication from 00:1f:5b:88:6f:1f (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:1f:5b:88:6f:1f
wlan0: RX AssocResp from 00:1f:5b:88:6f:1f (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:1f:5b:88:6f:1f)
wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
padlock: VIA PadLock not detected.
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sdb.
usb 7-1: USB disconnect, address 2
usb 7-2: new high speed USB device using ehci_hcd and address 3
usb 7-2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access S31B0806 USB DISK 1100 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: [sdb] 2030592 512-byte hardware sectors (1040 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 2030592 512-byte hardware sectors (1040 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
lsmod
Module Size Used by
nls_cp437 5888 1
vfat 10880 1
fat 45984 1 vfat
aes_i586 8064 1
aes_generic 27432 1 aes_i586
usb_storage 84800 1
joydev 10048 0
pcmcia 33068 0
firewire_ohci 16512 0
firewire_core 36928 1 firewire_ohci
crc_itu_t 2304 1 firewire_core
arc4 2176 2
ecb 3072 2
ohci1394 28720 0
serio_raw 5508 0
yenta_socket 23436 1
rsrc_nonstatic 11264 1 yenta_socket
ieee1394 79288 1 ohci1394
pcmcia_core 33300 3 pcmcia,yenta_socket,rsrc_nonstatic
pcspkr 2816 0
psmouse 36752 0
i2c_i801 9232 0
i2c_core 19348 1 i2c_i801
iwl4965 101748 0
mac80211 130572 1 iwl4965
cfg80211 16392 1 mac80211
video 16656 0
output 3200 1 video
ehci_hcd 33932 0
bay 4736 0
wmi 6056 0
uhci_hcd 22288 0
usbcore 129904 4 usb_storage,ehci_hcd,uhci_hcd
intel_agp 23740 0
agpgart 28244 1 intel_agp
sg 27188 0
thinkpad_acpi 53624 0
nvram 7436 1 thinkpad_acpi
thermal 15260 0
processor 32096 3 thermal
evdev 9472 0
fan 4356 0
button 6416 0
battery 10372 0
ac 4484 0
snd_seq_oss 30336 0
snd_seq_midi_event 6656 1 snd_seq_oss
snd_seq 48560 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 6796 2 snd_seq_oss,snd_seq
snd_hda_intel 336440 0
snd_hwdep 7428 1 snd_hda_intel
snd_pcm_oss 38656 0
snd_pcm 68228 2 snd_hda_intel,snd_pcm_oss
snd_timer 19848 2 snd_seq,snd_pcm
snd_page_alloc 8072 2 snd_hda_intel,snd_pcm
snd_mixer_oss 14848 1 snd_pcm_oss
snd 46628 9 snd_seq_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hwdep,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 6496 1 snd
e1000e 90916 0
rtc_cmos 9120 0
rtc_core 15516 1 rtc_cmos
rtc_lib 2944 1 rtc_core
ext3 124040 1
jbd 44052 1 ext3
mbcache 7172 1 ext3
sd_mod 23320 5
sr_mod 15300 0
cdrom 34080 1 sr_mod
ata_piix 17668 0
ahci 25224 2
ata_generic 5636 0
pata_acpi 4992 0
libata 142224 4 ata_piix,ahci,ata_generic,pata_acpi
scsi_mod 92332 5 usb_storage,sg,sd_mod,sr_mod,libata
dock 7952 2 bay,libata
lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 0c)
00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Contoller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HBM (ICH8M-E) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 140M (rev a1)
03:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN Network Connection (rev 61)
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04)

Sorry to ressurect an old thread, but recently I've been getting random kernel panics on my t61 as well. I believe the root cause is the wireless card. I have an intel 4965 card just like you.

Touch screen for Lenovo thinkpad 10

I have broken the glass of screen.And now it is impossible to find this spare part (00HW275, 00HW277, 00HW278, 00HW361, 00HW363)Where i can buy this part in Europe, USA or Chine?

Directly from Lenovo. Related dicsussion https://forums.lenovo.com/t5/ThinkPad-Tablets/lenovo-thinkpad-10-20c1-cracked-lcd/m-p/2032193

Sporadic reboots of a Thinkpad T61

Hello,
we have a Lenovo Thinkpad T61 that reboots itself every few days without providing any information in the logs about the reason for this behaviour.
I ran the Lenovo pc-doctor and got a failed result for the nvidia gpu with the error code 7082. Could you please help me with the meaning of this error code? Is there a list where I can find out what this error code stands for?
Best Regards,
Matthias

reboot with no message might be overheating. cleaning the fan and replacing thermal paste is cheap and certainly won't hurt anything.

Thinkpad T61 LCD dim, go with led upgrade???

Hey I just got a T61 and the LCD screen is very dim/dull when the laptop is plugged in or on highest setting, its nearly as dim as my Lenovo N500 on lowest brightness setting!!!
I know I will need to replace most likely the inverter and possibly the bulb inside, but I am wondering if I should replace the screen as well, and if so is there a 14.1" widescreen for this laptop with a better more crisp screen "like the n500"???
there is an led upgrade kit for the t61 series and i think that would most likely make the screen like new besides the few blemishes that is there now.
whats everone think?

Your inverter is most likely fine, just a weak bulb, but if you've eveer tried to replace one of these it's not a simple matter, your best option is to replace the screen. As for an LED upgrade, I think that's snake oil, as these systems don't have the necessary electronics to power an LED backlight. I have seen some (very expensive) circuitry that claims to control an LED backlight, but good luck getting it to work with things like your computes brightness settings, if it works at all it will probably be always on as the inverter isn't designed to control led lights.
Perhaps someone has designed a kit that resolves some/all of these problems... but then you're still back at the point of having to install it in the screen. If you have a samsung screen they are a nightmare to open, you'll probably need to cut the screen open and tape/glue it back together. Other brands aren't as bad, but to do this right you'll need a labritory grade "clean room", because as soon as you open the LCD every partical of dust in the air will stick to the screen and you'll never get it out without replacing it with smear marks. If you do manage to "pull this off", then please take photos to share with the community.
If I were you I'd just buy a screen, there are some good used ones available, and I may have one with a good backlight, but with a vertical line on the screen that I could send you if you cover the postage, perhaps you can use the parts to combine one good one.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

Problems in network contrllor of lenovo thinkpad sl510

I have a problem of wireless network controllor in my lenovo thinkpad sl510 laptop . I have installed different driver of lenovo like intel realtek but it doesnot work and doesnot show wireless network in my laptop .Is there any solution of this problem .
Moderator comment: Please don't post the same message(s) in multiple places as it splinters the discussion. Duplicate(s) removed.

Welcome to the community.
Please help us to better help you by providing a bit more information about your system.
What OS are you running and, if you know, which wireless card is installed in your machine?
If you are unsure about the card, please open Device Manager and do the following:
- Right-click on the wireless network adapter item.
- Select Properties from the pop-up and switch to the Details tab of the new window.
- Select Hardware Ids from the Property dropdown menu.
- Copy the information from the Value section of the window and paste back here.
For reference, your complete Driver Matrix is here --> http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&DocID=HT063325
Regards.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

Lenovo ThinkPad T60P 2007-8EU - Removing LCD Front Bezel

Greetings,
I have just spent about four hours dis-assembling my Lenovo ThinkPad T60P 2007-8EU with the purpose of disabling the Blue Tooth device. One of the last steps before you do that is to remove the LCD Front Bezel. I have read the documentation and believe I have removed all the screws but I still can´t remove the Bezel.
Document:
Hardware refference guide
MT 1951, 1952, 1953, 1954, 1955, 1956, 2007, 2008, 2009, 2613, 2623, and 2637
Pages 117 - 118
I have the 14.1 inch monitor . So the information should be on page 117.
Can any one give me some advice here?
Thank you.
Jean-Pierre
Solved!
Go to Solution.

People,
I figured this one out.
There were two additional screws that had to be extracted. The documentation clearly showed this, but I did not see them because they, as several others, were neatly covered with plastic patches glued the screw position. It hides the screw and looks nice but it is difficult to figure out and harder to put back into place looking just as good after access.
While I was waiting for an answer, I figured it out. Thanks to anyone that read my message. No advice necessary. Problem solved. Thank you.
Jean-Pierre

Black Screen Problem Lenovo ThinkPad X131e

I own a Lenovo ThinkPad X131e and recently the screen has become non-functional. The screen still lights up and everything else still works perfectly fine when I use an external monitor.
The screen itself is not cracked and does not appear to be damaged, and if possible I don't want to have to buy a new screen. The problem is nothing is displayed onto the screen.
The problem appears to be with left side where the screen is attached to the computer, however I took a little peak inside and the wire attaching the screen looks perfectly fine, only visible problem is the actual hinge (or whatever you want to call it) has snapped..
Obviously this would cause minor nuisenses such as the screen falling forward but I don't see how this could effect the display on the screen.
Any ideas on how to fix this?

Hi Sexylicka,
Welcome to Lenovo Community Forums!
I’m really sorry to hear that display in your Lenovo Thinkpad X131e is not functioning properly.
Have u tried to switch between computer display and external display using the FN+F7 combination?
Do a power drain! Unplug the power cable, remove the battery and then hold the power button for 30 to 60 seconds. Then reattach the power and attempt a boot.
Also, try updating your display drivers and see if it works.
Below is the link to enter downloads page and install the display driver.
• Support Drivers & Software downloads
Please click on "QUICK PATH”, enter X131e and select the exact model depending on the MTM number of your device.
If all the above said attempts fail, it could be an issue with the hardware (Possibly LCD screen, an inverter, cable or LCD back-light). I strongly suggest you to contact our technical support for assistance.
Click hereto open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
Best Regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Network connectivity problems on a Lenovo ThinkPad T60p

Greetings,
I am having connectivity problems with my Lenovo Thinkpad T60p. And I would really appreciate some help.
I know both ethernet connectivity and WiFi connectivity work because if I boot with different OS, I can access the network. So this is not a hardware problem. It is a software problem...
I have uninstalled the existing Ethernet and Network drivers by removing them from:
1. The Control Pannel -> Add/Remove programs
2. The Control Pannel -> System -> Hardware -> Device Manager
3. The directory level in C:/devices/win/ethernet etc.
I have downloaded the drivers again. Re-installed. Same issues.
I see both card in The Control Pannel -> System -> Hardware -> Device Manager . The Wireless card is
ok. The Ethernet card shows a yellow alert sign.
At boot time I get a message indicating a service cannot be started but the the system logs show no related errors.
As far as wireless, the network card appears, in the Network tab of the Windows Task Manager, but the status
is "Non Operational". I can see the networks around me, but I cannot connect, even when there is no encryption. This might be the first one to fix, since it will give me mobility even if I sacrifice speed and open myself to hacking.
As far as ethernet, I see the network card DOES NOT appear in the Network tab of the Windows Task Manager, but as I mentionned before, I know that there is a problem with that.
I hope someone can help me with this. The only other options I have are re-install the OS, install another one, or take the machine in for service, something I am reluctant to do, as I claim to be an IT professional for 30 years and that I can fix other people´s machines...
Thank you.
Regards,
Jean-Pierre
Solved!
Go to Solution.

Hello,
The ThinkPad T60p (2007-8EU) looks like a decently-configured ThinkPad:
2700(2.33GHz), 1GB RAM, 100GB 7200rpm HD, 14.1in 1400x1050 LCD, 256MB ATI FireGL V5200, CDRW/DVDRW, Intel 802.11abg wireless, Cingular WWAN, Bluetooth/Modem, 1Gb Ether, UltraNav, Sec Chip, FPR, 9c Li-Ion batt, WinXP Pro
The TPM driver is used to communicate with the T60p's integrated security module. You can download the latest version of the device driver from here on Lenovo's support site. Although listed as being for Windows 2000, XP and Vista, I believe it works just fine under Microsoft Windows 7 as well.
My working hypothesis is that removal of the third-party firewall damaged the network settings in Windows. That's a problem that periodically comes up with the various security software packages from different vendors.
What I would suggest at this point is the following:
Check with the third-party firewall vendor to see if they offer a manual uninstallation program to uninstall the software. Download that and run it per their instructions, booting into Safe Mode, if necessary.
When that process is complete, try resetting the network stack by issuing a "NETSH INT IP RESET RESETLOG.TXT" command per Microsoft Knowledgebase Article # 299357 "How to reset Internet Protocol (TCP/IP)". The article is applicable to Microsoft Windows XP SP3 and later.
At this point, you should be free of any services, device drivers, NDIS intermediate drivers, WinSock LSPs or other objects from the third-party firewall software, and all network connections should be restored to their default values.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Problem to come back from sleep mode in Lenovo Thinkpad T400 using Windows XP

Problem to come back from sleep mode in Lenovo Thinkpad T400 using Windows XP. Each time closing the T400 lid and try to make the laptop into a sleep mode for some time, it does not properly come out of sleep mode. Login screen is able to see when opening the lid for the first time, but it only seen for a while before then a black screen on T400 Thinkpad appears. Sometime the hard drive activity can be shown also. And then, to come back I had only one option to hard re-boot.
I tried Fn+F4 and power button once to come back but no use.
Please provide me some solution for this?
Thanks in Advance.

oh sorry and its been closed inbetween uses. When i open it the keyboard doesn't light up and it makes no sound.

Lenovo ThinkPad T61 14,1" LCD problem

Similar Messages

Maybe you are looking for