Lenovo ThinkPad X1 and Dell U2711 / HDMI?

Hello,
I plan to purchase the Dell U2711 monitor, it has a resolution of 2560 x 1440.
Will my Lenovo ThinkPad X1 handle this over the HDMI port?
Thanks in advance,
Simon

Similar Messages

Resolution issue with macbook pro 13 (late 2013) and dell u2711

I have a Dell U2711 (native resolution 2560x1440) that I use without issue with a macbook pro late 2007 (running 10.10.x), various iMacs and Macbook air 2011 running 10.10. When I say without issue, the display works at its native resolution.
Last week we got a MacBook Pro 13in, late 2013 model.
If I connect this macbook via either thunderbolt connection to the u2711 using either DVI port on the dell, the maximum resolution that I can use is 1920x1080. I am using apple mini displayport to DVI adaptors (I have tried 2 different ones and 2 different DVI cables, with no improvement). Clicking option + scaled in sys prefs does not give the native resolution as an option.
However, I just discovered that if I use a DVI to HDMI adaptor and I connect the macbook to the display I get the full native resolution without issue (2560x1440).
I have zapped the pram, powered down the display etc etc etc and it made no difference.
I would prefer to use the mini DIsplayPort to DVI adaptor rather than HDMI, any suggestions appreciated.
TIA.

Reset PRAM. http://support.apple.com/kb/PH18761
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Start up in Safe Mode. http://support.apple.com/en-us/HT1564
Best.

Request - ICC profile for the combination - w520 and Dell u2711

Greetings,
Due to the lack of a colorimeter, I come to you with a humble request for few calibrated ICC profiles for the DELL u2711 and the quadro 2000m w520. Probably tftcentral's review might be a well guidance for setting up a ICC profile http://www.tftcentral.co.uk/reviews/dell_u2711.htm
Thanks in advance,

hey utzutz,
could you explain on why you would like to get this ICC profiles ?
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Weird Colour Saturation issues with MBA and Dell U2711

Hey all,
Just picked up a new Dell U2711 for use with my MBAir and my PC Workstation. I have the MBA hooked up to the monitor via the DVI imput with the official Apple Mini DisplayPort to Dual-Link DVI Adapter. What i'm experiencing is some bizzare colour saturation discrepancies. I've attached two screenshots to illustrate the issue...
For some reason, icons in the dock and in Launchpad are displaying WAY more saturated than their icons when displayed in a regular finder window.
Has anyone else seen anything like this? Any ideas where I could start looking to find a solution?
Thanks!

Just updated the post with a new screenshot that better illustrates the problem. I origainly had a firefox issue as well, but that was fixed by changing the colour correction settings in that application.

Differences between Lenovo ThinkPad S430 and ThinkPad Edge S430

Is there a difference between Edge S430 and S430?
Because I've bought a Lenovo ThinkPad S430 w/o the Edge name!

All I can say is that it's an error in the marketing material.
I'm 100% certain that this feature does not exist on any ThinkPad Edge system, including your S430. There is not any possibility to add this feature because the hardware that makes it possible does not exist on ThinkPad Edge. It's not a case of providing some new software or BIOS to enable the feature.
If this is a feature that you require, and you bought your S430 based on this faulty marketing material, I suggest that you call the sales support phone number in your country and ask them how they want to handle it. I'm very sorry for this trouble caused by wrong marketing material.

Lenovo ThinkPad X200S Stuck ... !!!

When I bought my Lenovo ThinkPad X200S, All my friends make fun on me they called me (idiot) because they are Fans for DELL and/or HP …. They said that this Laptop look like Old style since they Create the first laptop in the world , they was proud with there laptops ,with a lot of Colored lights ,touch buttons ,cover Themes … etc
But I was defending my Own laptop the Great (Lenovo ThinkPad X200S) , and I was telling them , (Guys , I bought the laptop form the Creators of the technology , IBM , the great Name, The History , I bought the Performance , Durability ,Genus Engineering ) , even how much I trust Lenovo , I gave me self the right to tell them that (Lenovo products , never Broke , and never stuck or let me down ) ….
But, when I was trying to Stop my Bluetooth Device using (FUN + Radio Button) …..Ooops, the Laptop Stuck?!!!!!! , I was shocked!!!!! , it was like someone stabs me with a Knife in my back..!!! , if you want the Truth my friend make fun on me more and more , and I Toke my laptop home without even say good by …I was disappointed like never before .. !!!
I tried more and more to do that again in home , and it was the same result , Even I found that when I try to Start OR Stop the Wi-fi from the Button at the lest side of the laptop , the same thing happening 90% from my trying (laptop stuck again ) !!!!!!
I try to format and install new windows 7 pro …
I Install all the latest driver using (Thinkvantige system Update) …
I install all Microsoft Updates …
I install Norton internet security 2011 …
I install thinkvantige toolbox latest Version …
I make full hardware test , Everything was fine !!! , no problems at all
But, again, when I try to do the same thing, (Start or stop any radio device) using (Fun + Radio Button OR from the Wi-Fi Button at the left side) same thing happened again LAPTOP STUCK ….
My laptop still under warranty till 31/3/2012 ….
And now I have no place else to ask for Advice except here, so please lenovo Good Team, Help me
my faith in you will never Change.
Regards...
Alaa Al-Allan

My laptop info :
Product: ThinkPad X200s 7466-3RG
Operating system: Windows 7 professional 32 bit
Original description: SL9400(1.86GHz), 4GB RAM,120GB 5400rpm HD, 12.1in 1280x800 LCD, Intel 4500MHD, 802.11bg wireless, Vodafone WWAN, Bluetooth, 1Gb Ethernet, Secure chip, Fingerprint reader, 4c Li-Ion, Windows 7 professional 32
Warranty information
Type:
Model:
Serial number:
7466
3RG
xxxxxxx
Status:
Expiration date:
Location:
In warranty
2012-03-31
SWEDEN
Regards,
Alaa Al-allan
Moderator Note; s/n edited for members own protection

About Lenovo Thinkpad W540 for Music Production at a Professional Level

Hey there! I just signed up to this blog in search for an answer to my quest. I've heard a lot of good things about Lenovo ThinkPad W540, and I would like to make sure that I am getting what I really need to stay up to date, in this everyday changing technological world, for a while before making a purchase.
So far, this is what I got in my wish list:
Intel Core i7-4700MQ Processor (6MB Cache, up to 3.40GHz)
Windows 7 Professional 64
15.6" FHD (1920 x 1080) LED Backlit Anti-Glare Display, Mobile Broadband Ready
W540 NVIDIA Quadro K1100M 2G
16GB PC3-12800 DDR3L (4 DIMM)
500GB Hard Disk Drive, 7200rpm
DVD Recordable
Intel Dual Band Wireless 7260AC with Bluetooth 4.0
1 Year Depot or Carry-in
I would like to know what are the major differences between the above items, which I have in my wish list, and the ones below:
1) Intel Core i7-4930MX Processor (8MB Cache, up to 3.90GHz)
2)15.5” 3K (2880 x 1620), IPS LED Backlit Anti-Glare Display, Mobile Broadband Ready, Color Sensor
3) W540 NVIDIA Quadro K2100M 2G
4) 32GB PC3-12800 DDR3L (4 DIMM)
5) I would like a 1TB hard drive but they don't come at 7200 rpm, i guess the one in my wish list works fine.
6) Do I need a more sophisticated Optical Drive from the DVD Recordable in my wish list?
I guess whay I am trying to investigate is if I can function in the music production world with a Thinkpad W 540 with the specs already in my wish list? And, what difference would it make updating this machine with the specs below. Your assistance and comments will be greatly appreciated. Thank you!

Hi ColonellONeill, thank you for taking your time in attempt to solve my problems.
Temperatures varies, but it never reached to unbearably hot.
Shutdown warning: for the last couple of times, I did got the blue screen warning (that windows had problem and will restart after collecting the necessary information) on my Helix and hanged display on my external monitor. Otherwise, most of the time, there isn't warning at all.
I doubt if there is anything to do automatic windows update as I have scheduled it every morning at 3 'O' clock! Sometimes it works from weeks to couple of months without even noticing any of these technical problems but then when it starts, it stays for weeks; it just comes and goes - never been able to resolve the issues completely; even the technician.
(It just happend right now! and this time wihtout even warning, and Helix wasn't even running 30 minutes - temperature is normal, I can feel it's little warm.)
Currently I am using my Helix with Thinkpad USB 3 dock connected to external Monitor with wired keyboard and mouse connected back at the dock.

Thinkpad t500 and wifi card realtek RTL8192SE[solved]

I Buy a Lenovo Thinkpad T500 and the wireless adapter does not work in linux.
11b/g/n Wireless Lan Mini-PCI Express Adapter II.
lspci say:
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
lspci -n:
03:00.0 0280: 10ec:8172 (rev 10)
I need to buy another usb, pcmcia or mini pci-e wireless card.
Can you recommend one that works well? Because I never work with wifi cards on linux.
sorry my poor english
EDIT 21/07/09: add more information (thinkwiki):
http://www.thinkwiki.org/wiki/ThinkPad_ … Adapter_II
EDIT 22/10/09:
Finally came the expected driver, I think it's premature but it works perfectly.
Here the driver (r8192se_pci):
32bits: http://launchpadlibrarian.net/33927923/ … 009.tar.gz
64bits: http://launchpadlibrarian.net/34090326/ … bit.tar.gz
untar; make; make install; reboot and enjoy it
I test it with:
netcfg
standar commands:
ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid MySsid
wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
dhcpcd wlan0
The first time I compile the module, function correctly, but after scan for available networks I haven't any results.
Recompile and everything worked again
[b]I edit the wiki, pleased read it and help me because my English is a bit basic.
thanks
Last edited by takedown (2009-10-23 00:55:44)

Please note that the T500 has different hardware configurations.
Other options in wireless card (for the T500): intel 5100 - intel 5300.
This models work fine under linux
lspci -vv:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 41c9
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc226800 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: heci
Kernel modules: heci
00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) (prog-if 85 [Master SecO PriO])
Subsystem: Lenovo Device 20ea
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 1828 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1820 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 1810 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: ata_generic, pata_acpi, ide-pci-generic
00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) (prog-if 02 [16550])
Subsystem: Lenovo Device 20ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1830 [size=8]
Region 1: Memory at fc024000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [e0] PCIe advanced features <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc226c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fc020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4300000-f43fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 1, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4100000-00000000f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18e0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fc227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 00005000-00008fff
Memory behind bridge: f4800000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Lenovo Device 20f4
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device 20f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 1c48 [size=8]
Region 1: I/O ports at 183c [size=4]
Region 2: I/O ports at 1c40 [size=8]
Region 3: I/O ports at 1838 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fc226000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Mask- 64bit- Count=1/16 Enable+
Address: fee0300c Data: 4199
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc227400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
Subsystem: Lenovo Device 20c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: 80000000-83fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 20c7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f4801000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
15:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
Subsystem: Lenovo Device 20c8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f4801800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
15:00.3 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
15:00.4 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 11)
Subsystem: Lenovo Device 20ca
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
15:00.5 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 11)
Subsystem: Lenovo Device 20cb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

[SOLVED] Bumblebee: Failed to initialize GPU with Lenovo ThinkPad W530

SOLVED: See post #20
After years, I decided to come back to the wonderful distro, Arch and back to the forums. Yay!
However, I installed Arch to my new laptop - Lenovo ThinkPad W530 and it uses NVIDIA Quadro K1000M alongside Intel graphics with Optimus technology. Arch is running fine, but I cannot run applications through optirun and I get:
[exitium@rambutan ~]$ optirun -vv nvidia-settings
[ 485.536478] [DEBUG]Reading file: /etc/bumblebee/bumblebee.conf
[ 485.536909] [DEBUG]optirun version 3.2.1 starting...
[ 485.536922] [DEBUG]Active configuration:
[ 485.536927] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[ 485.536931] [DEBUG] X display: :8
[ 485.536934] [DEBUG] LD_LIBRARY_PATH: /usr/lib/nvidia:/usr/lib32/nvidia
[ 485.536938] [DEBUG] Socket path: /var/run/bumblebee.socket
[ 485.536941] [DEBUG] Accel/display bridge: auto
[ 485.536945] [DEBUG] VGL Compression: proxy
[ 485.536948] [DEBUG] VGLrun extra options:
[ 485.536952] [DEBUG] Primus LD Path: /usr/lib/primus:/usr/lib32/primus
[ 485.536972] [DEBUG]Using auto-detected bridge virtualgl
[ 485.537190] [INFO]Response: No - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please
[ 485.537204] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please
[ 485.537209] [DEBUG]Socket closed.
[ 485.537223] [ERROR]Aborting because fallback start is disabled.
[ 485.537229] [DEBUG]Killing all remaining processes.
As seen, it says "Failed to initialize the NVIDIA GPU". I have tried different solutions found from these forums and several other places but none of them have worked - the problem remains same. Does anyone have idea how I could fix this? I read somewhere else that there could be issues with newest nvidia drivers - is this possible?
bumblebee.conf:
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia:/usr/lib32/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
xorg.conf.nvidia
Section "ServerLayout"
Identifier "Layout0"
Option "AutoAddDevices" "false"
Option "AutoAddGPU" "false"
Option "UseDisplayDevice" "none"
EndSection
Section "Device"
Identifier "DiscreteNvidia"
Driver "nvidia"
VendorName "NVIDIA Corporation"
# If the X server does not automatically detect your VGA device,
# you can manually set it here.
# To get the BusID prop, run `lspci | egrep 'VGA|3D'` and input the data
# as you see in the commented example.
# This Setting may be needed in some platforms with more than one
# nvidia card, which may confuse the proprietary driver (e.g.,
# trying to take ownership of the wrong device). Also needed on Ubuntu 13.04.
BusID "PCI:01:00:0"
# Setting ProbeAllGpus to false prevents the new proprietary driver
# instance spawned to try to control the integrated graphics card,
# which is already being managed outside bumblebee.
# This option doesn't hurt and it is required on platforms running
# more than one nvidia graphics card with the proprietary driver.
# (E.g. Macbook Pro pre-2010 with nVidia 9400M + 9600M GT).
# If this option is not set, the new Xorg may blacken the screen and
# render it unusable (unless you have some way to run killall Xorg).
Option "ProbeAllGpus" "false"
Option "NoLogo" "true"
Option "UseEDID" "false"
Option "UseDisplayDevice" "none"
EndSection
Thank you in advance!
Last edited by Exitium (2013-12-18 11:29:54)

Hi!
Exactly the same issue here. Notebook -> Thinkpad W530
Currently running on:
linux 3.11.3-1
nvidia 325.15-8
nvidia-utils 325.15-1
bbswitch 0.7-14
Error:
username@hostname ~ $ optirun -vv nvidia-settings
[ 839.449203] [DEBUG]Reading file: /etc/bumblebee/bumblebee.conf
[ 839.449495] [INFO]Configured driver: nvidia
[ 839.449729] [DEBUG]optirun version 3.2.1 starting...
[ 839.449774] [DEBUG]Active configuration:
[ 839.449817] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[ 839.449836] [DEBUG] X display: :8
[ 839.449856] [DEBUG] LD_LIBRARY_PATH: /usr/lib/nvidia:/usr/lib32/nvidia
[ 839.449875] [DEBUG] Socket path: /var/run/bumblebee.socket
[ 839.449890] [DEBUG] Accel/display bridge: auto
[ 839.449909] [DEBUG] VGL Compression: proxy
[ 839.449936] [DEBUG] VGLrun extra options:
[ 839.449953] [DEBUG] Primus LD Path: /usr/lib/primus:/usr/lib32/primus
[ 839.449996] [DEBUG]Using auto-detected bridge virtualgl
[ 839.450294] [INFO]Response: No - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please
[ 839.450344] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please
[ 839.450373] [DEBUG]Socket closed.
[ 839.450398] [ERROR]Aborting because fallback start is disabled.
[ 839.450419] [DEBUG]Killing all remaining processes.
dmesg output:
[ 81.162604] bbswitch: enabling discrete graphics
[ 81.396637] pci 0000:01:00.0: power state changed by ACPI to D0
[ 81.396663] thinkpad_acpi: EC reports that Thermal Table has changed
[ 81.483200] nvidia: module license 'NVIDIA' taints kernel.
[ 81.483205] Disabling lock debugging due to kernel taint
[ 81.488096] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 81.488289] [drm] Initialized nvidia-drm 0.0.0 20130102 for 0000:01:00.0 on minor 1
[ 81.488294] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 325.15 Wed Jul 31 18:50:56 PDT 2013
[ 81.665938] nvidia 0000:01:00.0: irq 50 for MSI/MSI-X
[ 81.670434] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.670528] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.670594] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.670659] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.670723] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.670960] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.671192] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 81.671258] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.879826] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.905471] NVRM: GPU at 0000:01:00.0 has fallen off the bus.
[ 85.905479] NVRM: os_pci_init_handle: invalid context!
[ 85.905481] NVRM: os_pci_init_handle: invalid context!
[ 85.905486] NVRM: GPU at 0000:01:00.0 has fallen off the bus.
[ 85.905490] NVRM: os_pci_init_handle: invalid context!
[ 85.905491] NVRM: os_pci_init_handle: invalid context!
[ 85.930135] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.930442] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.930719] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.930990] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.931258] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.931526] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.931794] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.932062] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.932329] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.932595] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.932862] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.933129] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.933396] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.933662] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.933942] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.934197] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.934452] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.934706] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.934960] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.935215] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.935469] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.935722] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.935976] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
[ 85.940508] NVRM: RmInitAdapter failed! (0x25:0x28:1157)
[ 85.940517] NVRM: rm_init_adapter(0) failed
xorg.conf.nvidia:
Section "ServerLayout"
Identifier "Layout0"
Option "AutoAddDevices" "false"
Option "AutoAddGPU" "false"
EndSection
Section "Device"
Identifier "DiscreteNvidia"
Driver "nvidia"
VendorName "NVIDIA Corporation"
# If the X server does not automatically detect your VGA device,
# you can manually set it here.
# To get the BusID prop, run `lspci | egrep 'VGA|3D'` and input the data
# as you see in the commented example.
# This Setting may be needed in some platforms with more than one
# nvidia card, which may confuse the proprietary driver (e.g.,
# trying to take ownership of the wrong device). Also needed on Ubuntu 13.04.
BusID "PCI:01:00:0"
# Setting ProbeAllGpus to false prevents the new proprietary driver
# instance spawned to try to control the integrated graphics card,
# which is already being managed outside bumblebee.
# This option doesn't hurt and it is required on platforms running
# more than one nvidia graphics card with the proprietary driver.
# (E.g. Macbook Pro pre-2010 with nVidia 9400M + 9600M GT).
# If this option is not set, the new Xorg may blacken the screen and
# render it unusable (unless you have some way to run killall Xorg).
Option "ProbeAllGpus" "false"
Option "NoLogo" "true"
Option "UseEDID" "false"
Option "UseDisplayDevice" "none"
EndSection
bumblebee.conf:
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bu … PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia:/usr/lib32/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau

Thinkpad W510 and W530 accessories compatibility

Hello all,
From a previous post, I found that accessories such as the power adapter and docking station will not work between the Lenovo Thinkpad W510 and W540 models. Instead, are they compatible between a W510 and W530 and if not, how about a W510 and W520?
Solved!
Go to Solution.

No. W530 and W520 use the same docks and AC adapters; W510 uses different ones. All 3 have the same shape of battery, but the W530 needs one with an additional chip. A W530 battery will work in any of them. Nothing fits a W540. The only difference in the dock on the T510 (vs. T520, T530) is the AC jack is keyed for the 170W adapter.

Lenovo ThinkPad s431 SSD replacement

Hi, guys! I want to buy Lenovo ThinkPad s431, and I have a question.
Can I change 24GB SSD disk with larger disk (for example 128 or 256 GB)?
Is it necessary to replace regular HDD for this or the laptop has a mSata or 2.5 slot on motherboard?
Thanks!

I guess I wont be buying Lenovo again

Lenovo ThinkPad R61 wont power on?

Hi, just so you know i'm new to these forums
Anway.. I have a Lenovo ThinkPad R61, and it wont turn on.
When the charger is connected, the Orange light flashes and the Green light stays on - it wont turn on by the button.
When the battery is out, and the charger is connected the green light stays on - it still wont turn on.
And without the charger it does nothing.
I have tried holding down the power button for 30 seconds with the charger and battery out, and it still does nothing.
Any idea's?
Thanks in advance!

Welcome to the Support Forums danporter15!
Were you able to contact the support center? All Lenovo Products come with a 1 Year Limited Warranty, if you would like to have more indepth troubleshooting, do not hesitate to contact your support center. You can verify your warranty status here.
Please keep us posted!
Thank you for being a part of the Lenovo Family,
Catie
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Donate KUDOS and Click "Accepted Solution"

Stripes on screen Lenovo Thinkpad x121e

Hi,
I had sometimes horiznotal stripes on screen Lenovo Thinkpad x121e and sent it to service.Here is video:
http://www.youtube.com/watch?v=tpTtHWkC1jI
They did tests and said that everything is OK,stripes didn´t discover.Few days ago,one day I see stripes on screen again.Where is problem?

hey LTP80,
do you have any devices near it such as a radio player, cellphone, etc that could cause an interference ?
use that unit at a different location and see if the stripes appear. i'm guessing something in the original location is causing the stripe to appear.
that is why when the service center looked into the issue, they didnt find any.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Thinkpad W510 and W540 accessories compatibility

Hello all,
I have a Lenovo Thinkpad W510 and I am looking to upgrade to a W540. For my current W510 I have a docking station and two power adapters. Will they all still work on a W540?
Solved!
Go to Solution.

Hello.
No, neither the dock nor the power supplies will work. The xx40 series of ThinkPads use the new rectangle tip power jacks instead of the barrel shaped ones, thus requiring new models of both.
Cheers!
ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

Black Screen Problem Lenovo ThinkPad X131e

I own a Lenovo ThinkPad X131e and recently the screen has become non-functional. The screen still lights up and everything else still works perfectly fine when I use an external monitor.
The screen itself is not cracked and does not appear to be damaged, and if possible I don't want to have to buy a new screen. The problem is nothing is displayed onto the screen.
The problem appears to be with left side where the screen is attached to the computer, however I took a little peak inside and the wire attaching the screen looks perfectly fine, only visible problem is the actual hinge (or whatever you want to call it) has snapped..
Obviously this would cause minor nuisenses such as the screen falling forward but I don't see how this could effect the display on the screen.
Any ideas on how to fix this?

Hi Sexylicka,
Welcome to Lenovo Community Forums!
I’m really sorry to hear that display in your Lenovo Thinkpad X131e is not functioning properly.
Have u tried to switch between computer display and external display using the FN+F7 combination?
Do a power drain! Unplug the power cable, remove the battery and then hold the power button for 30 to 60 seconds. Then reattach the power and attempt a boot.
Also, try updating your display drivers and see if it works.
Below is the link to enter downloads page and install the display driver.
• Support Drivers & Software downloads
Please click on "QUICK PATH”, enter X131e and select the exact model depending on the MTM number of your device.
If all the above said attempts fail, it could be an issue with the hardware (Possibly LCD screen, an inverter, cable or LCD back-light). I strongly suggest you to contact our technical support for assistance.
Click hereto open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
Best Regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Lenovo ThinkPad X1 and Dell U2711 / HDMI?

Similar Messages

Maybe you are looking for