Lenovo X201, Xorg, modesetting problem

This is a new model Lenovo X201 http://www.thinkwiki.org/wiki/Category:X201Type 3626 (Core i5).
Did a fresh installation from 2010.05-core-i686 CD with x86_64. I had the dreaded "dark screen" problem caused by kernel mode setting switching off the backlight! I can boot only with the 'nomodeset' kernel boot parameter.
The problem persists after 'pacman -Syu' 2.6.34-ARCH #1 SMP PREEMT Sat Jun 19 00:07:49 CEST 2010 x86_64. As a result I can't startx, the log says - using xf86-video-intel driver, no xorg.conf:
(II) VESA: driver for VESA chipsets: vesa
(--) using VT number 7
(II) Primary Device is: PCI 00@00:02:0
(WW) Falling back to old probe method for vesa
(EE) intel(0): no kernel modesetting driver detected
(II) UnloadModule: "intel"
(EE) Screen(s) found, but none have a usable configuration
Fatal server error:
no screens found
Obviously, I have to boot without the 'nomodeset' parameter.
How should I progress? Compiling a more recent kernel? Which version? What configuration parameters are needed?

I have an X61T, and I had a dark screen problem for the longest time. I had to guess at when the login prompt showed up and enter my username and password 'blind'. The monitor turned off halfway through the boot sequence and turned on again after I started X. Trying to turn KMS off gave the same kind of error that you got about usable configurations. Perhaps we had the same problem? If not, maybe this will help somebody else with a dysfunctional screen.
I fixed it by leaving vga=xxx out of the kernel line of my menu.lst and keeping KMS on (I think it's on by default in the default arch linux kernel). Yes, I compiled my own kernel with i915 and intel_agp, but that didn't fix the problem for me. Here's the relevant line:
kernel /vmlinuz26-x61t root=/dev/sda5 ro

Similar Messages

Lenovo X201, xorg switching to track point

There are so many changes to the xorg configuration recently, what is the best way to switch to track point (only) on my Lenovo X201:
a) editing xorg.conf as in http://www.thinkwiki.org/wiki/How_to_co … rg.conf.29 or
b ) adding /etc/X11/xorg.conf.d/20-thinkpad.conf http://www.thinkwiki.org/wiki/How_to_co … org.conf.d ?
My default xorg.conf has
Section "Input Device"
Identifier "Mouse0"
Drivier "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxis Mapping" "4 5 6 7"
EndSection
and the default /etc/X11/xorg.conf.d/10-evdev.conf with all sorts of "catchall".
The track point is not usable, it drives the cursor mad every couple of seconds. The touch pad works, but for me it should not.
Also the upper 3-button mouse is dead, only the lower 2 buttons work, again I want it the other way.

Here is my config on a T500:
root:/home/takedown # cat /etc/X11/xorg.conf.d/10-trackpoint.conf
Section "InputClass"
Identifier "Trackpoint Wheel Emulation"
MatchProduct "TPPS/2 IBM TrackPoint|DualPoint Stick|Synaptics Inc. Composite TouchPad / TrackPoint|ThinkPad USB Keyboard with TrackPoint|USB Trackpoint pointing device"
MatchDevicePath "/dev/input/event*"
Option "EmulateWheel" "true"
Option "EmulateWheelButton" "2"
Option "Emulate3Buttons" "false"
Option "XAxisMapping" "6 7"
Option "YAxisMapping" "4 5"
EndSection
On startUp i run:
# synclient TouchpadOff=1
this script to swap between touchpad and trackpoint with Fn+F8:
root:/home/takedown # cat /etc/acpi/events/ultranav
event=ibm/hotkey HKEY 00000080 00001008
action=/etc/acpi/actions/ultranav.sh
root:/home/takedown # cat /etc/acpi/actions/ultranav.sh
#!/bin/bash
PATH="/bin:/usr/bin:/sbin:/usr/sbin"
export DISPLAY=:0
USER=`who | grep ':0' | grep -o '^\w*' | head -n1`
if [ `su $USER -c 'synclient -l | grep TouchpadOff | cut -b 31-32'` -ne 0 ]; then
su "$USER" -c "synclient TouchpadOff=0"
su "$USER" -c "xinput set-int-prop \"TPPS/2 IBM TrackPoint\" \"Device Enabled\" 8 0"
#su "$USER" -c "/usr/bin/kdialog --passivepopup Touchpad\ enable --title Thinkpad\ T500 "5""
else
su "$USER" -c "synclient TouchpadOff=1"
su "$USER" -c "xinput set-int-prop \"TPPS/2 IBM TrackPoint\" \"Device Enabled\" 8 1"
#su "$USER" -c "/usr/bin/kdialog --passivepopup Touchpad\ disable --title Thinkpad\ T500 "5""
fi
maybe you can avoid in bios settings

Can't Access Oracle EBS with a Lenovo X201 laptop

My Company runs Oracle E-Business Suite version 11.5.10.2. I recently had to get a new laptop (Lenovo X201). I can log onto the Oracle Application Home Page and select a responsibility, but when I select an operation, like Invoice Inquiry in the Payables Module for instance, I get the following message, "This tab has been recovered. A problem with this web page has caused Internet Explorer to close and reopen the tab." The laptop is running the XP operating system and Internet Explorer 8.0.6001.18702. Our IT staff can't figure out the problem. They looked at all the usual cause for problems, like pop-up blockers, etc. They also spoke to Lenovo Support without finding a resolution. We experienced a similar problem with Dell laptops that they were able to resolve. Has anyone experienced this problem with a recent-vintage Lenovo computer and found a solution?

Can you find any details about the error in Apache log files and/or Sun JRE Console Window?
If the issue is reproducible, please make sure you meet the minimum requirements as per these docs.
Recommended Browsers for Oracle E-Business Suite 11i [ID 285218.1]
IE8 AND R12 SECURITY SETTING REQUIREMENT ON CROSS SITE SCRIPTING (XSS) [ID 1069497.1]
Thanks,
Hussein

Having trouble with the trackpad on my Lenovo X201

I'm trying ot get Arch set up on my new Lenovo X201 thinkpad and I've got as far as getting X up and running. However, I'm having some problems with the trackpad.
First of all the mouse pointer is a little crazy, leaps all over the screen and is very difficult to control - any ideas on how to improve on that? Also, I've tried following various wiki examples of how to get things working (in particular using the right side of the pad for vertical scrolling) and I'm not having much luck there...
Any advice?

Never mind - it turns out that just installing synaptics fixed everything :-)

Type euro sign on Windows 7 64-bit Lenovo X201

Hi,
The subject says it all: how do I type a Euro sign on my Lenovo X201, Windows 7, 64-bit. It is a US keyboard.
I have tried Alt+4, Alt+5, Alt+e, etc, ....
Thanks.
Solved!
Go to Solution.

For others with this problem, there are a couple solutions. First you can use the ALT codes, but this requires a separate numeric keypad (not the numbers along the top of a laptop). Instructions for that are here.
With a laptop you need to use one of the alternate methods here.
Or if you are using Firefox or PaleMoon you can use this addon. The last is my favorite because it allows you to use characters from any language, including extended characters, with no need to lookup a code. Here is the Euro € and it took 2 mouse clicks.
Hoov
Microsoft MVP - Consumer Security
SpywareHammer.com

Lenovo M92P 2992E5U Monitor problem

Just recently bought a Lenovo M92P 2992EU from amazon.
http://www.amazon.com/Lenovo-2992E5U-M92p-Desktop/dp/B00A2V3SV0/ref=sr_1_4?ie=UTF8&qid=1375841434&sr...
When i plug my monitor to the motherboard VGA port, there's no display on the monitor. However, when i plug my monitor into the Video card's VGA port, there's display.
What's wrong with it? This is my second lenovo with the same problem. I didnt do anything to it. It is my first day using it. Also, i called Lenovo Tech Support, they remotely helped me do all of the driver update....

You must enable multi-monitor support if you wish to use the internal graphics when a graphics card is installed.
http://support.lenovo.com/en_NL/downloads/detail.page?DocID=HT062228

Lenovo X201 external monitor resolution issue

Hi,
I'm having issues connecting my Lenovo X201 through the docking station -> display port -> Dell 3011. The native resolution for the monitor is 2560x1600. However, I currently can only set the resolution to 1920x1080 (ugly!) as any high resolution results in the monitor entering power save mode.
I'm using xrandr to set the video mode in my .xinitrc (running dwm). This creates a good Xinerama config for dwm.
I'm currently using the line
xrandr --output DP1 --mode 1920x1080 --above LVDS1
to set my resolution. When I change to --auto or --mode 2560x1600, or 1920x1200 etc I get the blank screen on the external monitor. I'm using the xf86-video-intel-sna driver package (I tried the -uxa as well to no avail).
Any hints?

I was able to get it by having arandr help generate the config, here's the solution that worked for me:
xrandr --output HDMI1 --off --output LVDS1 --auto --right-of DP1 --output DP1 --pos 0x0 --rotate normal --auto --output VGA1 --off

Lenovo X201 Series Tablet/Laptop

Hi I recently bought a Lenovo X201 Series Laptop but the screen is cracked it has a touchscreen interface I would like to know can I replace the touchscreen with a 12.1inch LED or LCD Screen as I dont want to spend to much on a touch screen details of laptop is below
Product ID: 2985DMG
Specs:
Corei7 CPU,500GB Hard Drive 4GB Ram 12.1inch Touch screen.

Hi,
there is a lot matrices are installed into x201t. Models also depend of the backlight type - LED or CCFL. I'm not sure whether any supported matrices models are compatible with your laptop. Also there are different LCD cable assembly and LCD rear cover assembly depending of the backlight type.
To ensure what matrice you have and what's compatible check out on Lenovo' site parts list of your laptop by its [laptop] serial number. Support site doesn't answer a question by MTM only.
I think it's impossible to fit non touch matrice into the tablet because of the different size (width). Compare the width of x201 and x201t.
UPD
Service parts DB says your laptop has 12.1-in. WXGA LCD panel, LED backlight (300-nit LCD), FRU 45N6092 or 45N5388.
x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
Do it well, worse becomes itself
Русскоязычное Сообщество English Community Deutsche Community Comunidad en Español

Lenovo X201, ethernet Intel 82577LM, no network

This is the same notebook discussed in
http://bbs.archlinux.org/viewtopic.php?id=98993
It loads the module e1000e. I have arch installed. It loads the module
e1000e and ifconfig reacts. It won't register the ip-address assigned
through dhcp.
Hardware: Lenovo X201 with the ethernet chip Intel 82577LM
# uname -a
Linux myhost 2.6.34-ARCH #1 SMP PREEMPT Mon May 17 08:36:58
UTC 2010 i686 Intel(R) Core(TM) i5 CPU M 540 @ 2.53 GHz
GenuineIntel GNU/Linux
# dhcpcd eth0
dhcpcd: eth0: broadcasting for a lease
dhcpcd: eth0: offered 192.168.1.103 from 192.168.1.1
dhcpcd: eth0: acknowledged 192.168.1.103 from 192.168.1.1
dhcpcd: eth0: checking for 192.168.1.103
dhcpcd: eth0: leased 192.168.1.103 for 86400 seconds
dhcpcd: eth0: MTU set to 1492
# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 5c:....
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2392 errors:0 dropped:0 overruns:0 frame:0
TX packets:4448 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes: 745374 (718.1 Kb) TX bytes:552664 (539.7 Kb)
Memory:f2500000-f2520000
# ping 192.168.1.1
Network is unreachable
No routing table either.
Any help to get the network going, is welcome.

I downloaded the package (the *.xz file) from the repo, for example http://www.archlinux.org/packages/extra/i686/dhclient/ (watch the "Package Actions" box top right), transferred it through USB memory stick to the laptop then "pacman -U ...*.xz".
- Comment out all the four lines: eth0, INTERFACES, gateway and ROUTES in /etc/rc.conf
- kill dhcpcd (dhcpcd -k eth0) or reboot
- do "dhclient eth0".

Lenovo X201 and 3g dongle compatibility

Hi
Please firstly excuse my ignorance.
I have recently purchased a Lenovo X201 but am having an issue getting connected to Orange 3g using a Huawei dongle. Usually and to the best of my knowledge these setups are plug and play, but when the device is installed it doesn't recognise the hardware as a dongle but as a mass storage device.
Is it likely that the dongle needs replacing or will I have to download any other software and/or can I only use the 3g with an additional purchase of some hardware i.e. Gobi2000 (what is this and what does it do?)
Your help is appreciated

hey Jim1low,
for this you will need to check with Orange 3G, you may need to install a driver/software specific to the Huawei dongle.
this is probably the reason why the dongle is recognized as a storage device instead.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Lenovo X201 Supervisor password

Hi , ive forgot the supervisor password for my lenovo X201 , i need to reinstall windows but cannot due to the external dvd rw being in the "excluded devices" section.
I have been having a read around and so far i think my best bet is to pay for a service to remove the password on ebay.
Link removed by Moderator.
Although its not for the x201 i had a try and the board is completely different (even though he says it will work reading the comments.
I was wondering if there was any other way of doing it other than buying one of the devices that read the chip.
Thankyou

Per the Community Rules:
"No posts shall include instructions or directions intended to subvert security measures, including passwords, locking mechanisms, fingerprint scans, etc, or to subvert safety measures. Nor shall any posts provide descriptions to the location of, nor direct links to content related to these topics."
Thread locked.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

Lenovo doesn't solve problems in Warranty

S/N: CBxxxxxxxx
Ticket: 7020288989
Model: G570
Phone support in Romania, Service in Poland
First times in service they changed hdd and motherboard.
Now, when the issues are clearly visible they do not find anything. I am thinking that they do not want to refund since this is the third time in service and the last time.
Problem Description:
At a simple touch in different places the laptop is freezing or reset. Also the bios clock got to the default time: 01/01/2010
Movies
1. Bios reset
http://www.youtube.com/watch?v=L3txChoJbsE
2. Bios reset, windows recovery menu reset, windows freezing
http://www.youtube.com/watch?v=z_Ld1qCe6yE
My next steps:
Neutral Technical Assistant
Office for Consumer Protection
Sue Lenovo
Conclusion:
1. Phone support - I know more things than they do (I work with computers)
2. Service - unable to find a simple problem
3. Communication problem between phone support in Romania and service in Poland
4. More than 15 other people with simillar issues on models ending with 570:
http://forum.softpedia.com/topic/851774-garantie-lenovo-v570/ - translate here with google translate from romanian, the link for translation addded invalid characters
5. MOST IMPORTANT: ------------------------------------
STAY AWAY FROM LENOVO, IF YOU HAVE PROBLEMS, THEY DO NOT HELP AND TREAT YOU LIKE A PIECE OF GARBAGE!
Moderator Note; s/n edited for member's own protection

Patternflyer,
I've very sorry to hear that this wound up being such an ordeal for you!
The way it is supposed to work, is that models sold through distribution (whether Best Buy, CDW, etc) have the 12 months plus a couple of months of "padding" added to make up for time spent in inventory in distribution. Usually a customer will have at least 12 months of time that way. The warranty starts from date of manufacture.
In some cases, it took more time to sell through than expected and the customer might have less than 12 months by the time they get it. This can be reset, as you note, with a proof of purchase showing the type and serial number of the unit.
Custom configured systems ordered direct through Lenovo are shipped directly from manufacturing, and so the warranty starts then.
I agree with many of your points and we are working toward more chat services to be available, and also more integrations when you register your system. With a direct sale, we know the customer, while in a retail scenario, we won't. Ideally the registration process will update records.
I am also optimistic that we will have greater account integration in the not too distant future - where your account registered could have credentials connected with our support site, sales, the forum and other Lenovo properties.
Best regards,
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Lenovo x201 tablet laptop Integrated Webcam not working

I recently had to reinstall windows onto the Lenovo x201 tablet laptop and I can't get the integrated webcam to work on Google+. I tried downloading the integrated camera driver but during installation it stops about 3/4s of the way and the installation cancels. Not sure how to fix this , I checked under Device Manager and the camera driver is not listed under imaging devices. Does anyone have a solution to this? Thanks.

Hi
Welcome to the community.
As per our concern, I would suggest you to please re-install the camera driver from the below mentioned web link.
http://support.lenovo.com/en_SG/downloads/default.page?#
After that please perform the following steps.
1. Press Fn+F6 to enable the camera.
2. Click the Manage Settingsbutton. The Communications Utility window opens.
3. In the Communications Utility window, configure the camera settings depending on your individual needs.
Regards,
Sameer

Streaming aspect issues on Lenovo x201 - Windows 7

Hi there,
I am having an issue streaming from my PC Lenovo x201 to my TV. I stream Tv and films from my PC through my cable box (UPC Horizon) to my TV. I'm having an issue with the aspect ratio. The movies are being streamed to the tv in pan and scan rather tahn the proper 16:9 is there a setting I'm missing? I'm using boith Twonky and Win Media player and the result is the same. I have conmtacted the cable provider and all the settings are correct. So it must be the PC.
Any advice or thoughts greatly appreciated.
regards,
E.

any help appreciated, guys. Really stuck here.

Xorg.conf problems

hi
I have a working X-desktop with awesomeWM.
problem is, my X only works without a xorg.conf, not with the Xorg -configure one or a minimalistic one.
I have an intel 4500mhd graphic device, installed xf86-video-intel and evdev input devices.
KMS, hal and dbus are all loaded and running.
I need a working .conf file to set new font paths and I want to enable my hdmi output with xrandr.
this is my xorg log file when I start X without a .conf:
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.7.1.901 (1.7.2 RC 1)
Release Date: 2009-11-6
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.31-ARCH x86_64
Current Operating System: Linux myhost 2.6.31-ARCH #1 SMP PREEMPT Fri Oct 23 10:03:24 CEST 2009 x86_64
Kernel command line: root=/dev/disk/by-uuid/7082b361-a170-49ad-b5b7-d4fb6ca55cba ro i915.modeset=1
Build Date: 08 November 2009 04:08:18PM
Current version of pixman: 0.16.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Nov 18 10:22:11 2009
(II) Loader magic: 0x7c1a00
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(--) using VT number 7
(--) PCI:*(0:0:2:0) 8086:2a42:144d:c063 Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xfa000000/4194304, 0xd0000000/268435456, I/O @ 0x00001800/8
(--) PCI: (0:0:2:1) 8086:2a43:144d:c063 Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xfa400000/1048576
(==) Using default built-in configuration (30 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default intel Device 0"
Driver "intel"
EndSection
Section "Screen"
Identifier "Builtin Default intel Screen 0"
Device "Builtin Default intel Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default intel Screen 0"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (2)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.7.1, module version = 2.9.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 00@00:02:0
(WW) Falling back to old probe method for vesa
(WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: drmOpenMinor returns 7
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
"Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) GM45
(--) intel(0): Chipset: "GM45"
(II) intel(0): Output VGA1 has no monitor section
(II) intel(0): Output LVDS1 has no monitor section
(II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
(II) intel(0): Output DVI1 has no monitor section
(II) intel(0): Output DP1 has no monitor section
(II) intel(0): Output DVI2 has no monitor section
(II) intel(0): Output DP2 has no monitor section
(II) intel(0): Output DP3 has no monitor section
(II) intel(0): Output TV1 has no monitor section
(II) intel(0): Output VGA1 disconnected
(II) intel(0): Output LVDS1 connected
(II) intel(0): Output DVI1 disconnected
(II) intel(0): Output DP1 disconnected
(II) intel(0): Output DVI2 disconnected
(II) intel(0): Output DP2 disconnected
(II) intel(0): Output DP3 disconnected
(II) intel(0): Output TV1 disconnected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output LVDS1 using initial mode 1366x768
(II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so
(==) Depth 24 pixmap format is 32 bpp
(II) intel(0): [DRI2] Setup complete
(**) intel(0): Kernel mode setting active, disabling FBC.
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) UXA(0): Driver registered support for the following operations:
(II) solid
(II) copy
(II) composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): No memory allocations
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(==) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): direct rendering: DRI2 Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
record: RECORD extension enabled at configure time.
record: This extension is known to be broken, disabling extension now..
record: http://bugs.freedesktop.org/show_bug.cgi?id=20500
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/i965_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 361 x 203
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 2.3.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 1.2.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(II) Synaptics touchpad driver version 1.2.0
(**) Option "Device" "/dev/input/event10"
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
(II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
(II) SynPS/2 Synaptics TouchPad: buttons: left right middle
(**) Option "TapButton1" "1"
(**) Option "TapButton2" "2"
(**) Option "TapButton3" "3"
(--) SynPS/2 Synaptics TouchPad: touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
(**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
(--) SynPS/2 Synaptics TouchPad: touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device WebCam SCB-0340N
(**) WebCam SCB-0340N: always reports core events
(**) WebCam SCB-0340N: Device: "/dev/input/event9"
(II) WebCam SCB-0340N: Found keys
(II) WebCam SCB-0340N: Configuring as keyboard
(II) XINPUT: Adding extended input device "WebCam SCB-0340N" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Sleep Button
(**) Sleep Button: always reports core events
(**) Sleep Button: Device: "/dev/input/event7"
(II) Sleep Button: Found keys
(II) Sleep Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event6"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event2"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event4"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) Macintosh mouse button emulation: Close
(II) UnloadModule: "evdev"
(II) UnloadModule: "synaptics"
(II) AT Translated Set 2 keyboard: Close
(II) UnloadModule: "evdev"
(II) WebCam SCB-0340N: Close
(II) UnloadModule: "evdev"
(II) Sleep Button: Close
(II) UnloadModule: "evdev"
(II) Power Button: Close
(II) UnloadModule: "evdev"
(II) Video Bus: Close
(II) UnloadModule: "evdev"
(II) Power Button: Close
(II) UnloadModule: "evdev"

thank you for putting so much effort into my problem
I now tried this .conf file:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dri2"
Load "dri"
Load "record"
Load "glx"
Load "extmod"
Load "dbe"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "VGA1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
Option "dpms"
EndSection
Section "Monitor"
Identifier "LVDS1"
VendorName "Something"
ModelName "LaptopLCD"
Option "dpms"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "SWcursor" # [<bool>]
#Option "ColorKey" # <i>
#Option "CacheLines" # <i>
#Option "Dac6Bit" # [<bool>]
#Option "DRI" # [<bool>]
#Option "NoDDC" # [<bool>]
#Option "ShowCache" # [<bool>]
#Option "XvMCSurfaces" # <i>
#Option "PageFlip" # [<bool>]
Identifier "Card0"
Driver "intel"
# VendorName "Intel Corporation"
# BoardName "Mobile 4 Series Chipset Integrated Graphics Controller"
# BusID "PCI:0:2:0"
Option "Monitor-LVDS" "LVDS1"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "LVDS1"
SubSection "Display"
ViewPort 0 0
Depth 24
EndSubSection
EndSection
and this is my new log
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.7.1.901 (1.7.2 RC 1)
Release Date: 2009-11-6
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.31-ARCH x86_64
Current Operating System: Linux myhost 2.6.31-ARCH #1 SMP PREEMPT Fri Oct 23 10:03:24 CEST 2009 x86_64
Kernel command line: root=/dev/disk/by-uuid/7082b361-a170-49ad-b5b7-d4fb6ca55cba ro i915.modeset=1
Build Date: 08 November 2009 04:08:18PM
Current version of pixman: 0.16.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 19 06:53:16 2009
(++) Using config file: "/root/xorg.conf.new"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "LVDS1"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x7c1a00
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(--) using VT number 7
(--) PCI:*(0:0:2:0) 8086:2a42:144d:c063 Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xfa000000/4194304, 0xd0000000/268435456, I/O @ 0x00001800/8
(--) PCI: (0:0:2:1) 8086:2a43:144d:c063 Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xfa400000/1048576
(II) Open ACPI successful (/var/run/acpid.socket)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.7.1, module version = 2.9.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
(II) Primary Device is: PCI 00@00:02:0
(WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) GM45
(--) intel(0): Chipset: "GM45"
(II) intel(0): Output VGA1 using monitor section VGA1
(II) intel(0): Output LVDS1 using monitor section LVDS1
(II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
(II) intel(0): Output DVI1 has no monitor section
(II) intel(0): Output DP1 has no monitor section
(II) intel(0): Output DVI2 has no monitor section
(II) intel(0): Output DP2 has no monitor section
(II) intel(0): Output DP3 has no monitor section
(II) intel(0): Output TV1 has no monitor section
(II) intel(0): Output VGA1 disconnected
(II) intel(0): Output LVDS1 connected
(II) intel(0): Output DVI1 disconnected
(II) intel(0): Output DP1 disconnected
(II) intel(0): Output DVI2 disconnected
(II) intel(0): Output DP2 disconnected
(II) intel(0): Output DP3 disconnected
(II) intel(0): Output TV1 disconnected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output LVDS1 using initial mode 1366x768
(II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.1.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(==) Depth 24 pixmap format is 32 bpp
(II) intel(0): [DRI2] Setup complete
(**) intel(0): Kernel mode setting active, disabling FBC.
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) UXA(0): Driver registered support for the following operations:
(II) solid
(II) copy
(II) composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): No memory allocations
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(**) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): direct rendering: DRI2 Enabled
(WW) intel(0): Option "Monitor-LVDS" is not used
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
record: RECORD extension enabled at configure time.
record: This extension is known to be broken, disabling extension now..
record: http://bugs.freedesktop.org/show_bug.cgi?id=20500
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/i965_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 361 x 203
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 2.3.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
compiled for 1.7.0.901, module version = 1.2.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(II) Synaptics touchpad driver version 1.2.0
(**) Option "Device" "/dev/input/event10"
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
(II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
(II) SynPS/2 Synaptics TouchPad: buttons: left right middle
(**) Option "TapButton1" "1"
(**) Option "TapButton2" "2"
(**) Option "TapButton3" "3"
(--) SynPS/2 Synaptics TouchPad: touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
(**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0
(--) SynPS/2 Synaptics TouchPad: touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device WebCam SCB-0340N
(**) WebCam SCB-0340N: always reports core events
(**) WebCam SCB-0340N: Device: "/dev/input/event9"
(II) WebCam SCB-0340N: Found keys
(II) WebCam SCB-0340N: Configuring as keyboard
(II) XINPUT: Adding extended input device "WebCam SCB-0340N" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Sleep Button
(**) Sleep Button: always reports core events
(**) Sleep Button: Device: "/dev/input/event7"
(II) Sleep Button: Found keys
(II) Sleep Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event6"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event2"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event4"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "de"
(II) AIGLX: Suspending AIGLX clients for VT switch
edit: I just tested the VGA out with no .conf and it works, even with the correct display ratio (4:3 rather than 16:9 on my book). Tomorrow I will perhaps test the hdmi port on a friends new TV. If all works, I honestly don't care about messing around with xorg.conf ..
The font path problem is only relevant to urxvt so I will stick with xterm where extra fonts work without problem.
Last edited by lustikus (2009-11-19 10:36:06)

Lenovo X201, Xorg, modesetting problem

Similar Messages

Maybe you are looking for