Lenovo Z585 Ubuntu 13.04 / Windows 8 Dual Boot Issue - Wake from Suspend?

As the title says. I have been having an issue with waking the screen on my laptop after going into suspend from Ubuntu 13.04. (Also, same problem on Ubuntu 12.10 and Fedora 18)
When I close the lid, the computer will go into standby normally. Lights go out, and power light just blinks. Upon opening the lid I get the lights on the computer to come back and the fans come back on, however the screen stays black.
I have the following:
Processor: AMD A10-4600M APU with Radeon HD Graphics x 4
Driver: Gallium 0.4 on AMD ARUBA
I have tried updating drivers through Ubuntu. I have tried modifying the backlight controls through editing the grub.
I have tried several re-installs of multiple versions of the listed Linux above.
No matter what I do, I have the same issue(s) on all three versions.
A seperate issue is a weak wifi signal using the installed Broadcom wifi antenna. Sitting next to the router I only get about 60% strength. If I plug in my Belkin USB wireless antenna I get 100%.
Any help would be great!
Thanks

Bump

Similar Messages

Drivers for windows xp, Dual Booting issue

I have recently purchased a mac Book pro the 13 inch model, it came with lion installed by default this means boot camp only works for 7
So ive partioned my disk using boot camp and installed Xp onto the partioned part of the hd
Obviously the issue with this is that boot camp wont let me burn a disk for the drivers as it only supports 7
so really i need someway of getting the drivers, after googling for a while i couldnt find anything so if anyone has any suggestions it would be most appreciated.
Drivers would be for such thing as the wirelsess card, sound, graphics chip etc

XP is not supported in Lion or by the newer Apple computers. There are no XP drivers for lion or for the newer hardware. This issue has been discussed repeatedly in the Boot Camp forum: https://discussions.apple.com/community/windows_software/boot_camp

Error With Ubuntu and windows 8 dual boot

I have a levovo x240 and I had Ubuntu and windows 8 dual booted I removed the Ubuntu partition in windows partition modifier and when I restarted my computer it launch "grub rescue> "
How do I boot into windows and stop this problem

Yes, instead of posting in a forum dedicated to type, post in a forum associated with Premiere.
I will move your post for you.
- Dov

Cannot backup Windows 7 (dual-boot) image to external HD (formated as Mac OS Extended)

I cannot backup my Windows 7 (dual-boot) image to my external HD (formated as Mac OS Extended). I installed MacDrive 8.0 hoping to solve the problem but Windows 7 gives me an error when I try to create a backup: "...drive is not formatted as NTFS, cannot use as backup...".
I also tried making an Image of the Windows 7 partition through Disk Utility but was not allowed to do so.
I am not sure where else to go from here. I need to keep my external hard drive formatted as Mac OS Extended but I also need to backup my Windows 7 partition. I only have the single external at the moment. Is there a way to backup my Windows 7 partition?
Thanks

Winclone will backup your Windows partition to a Mac formatted drive.
Just search for Winclone on this forum and on Goggle.

Windows XP and Windows 7 dual boot (unable to create partition)

Hello, 3 months ago I bought in Bangkok a Lenovo S10-2 with 2 GB Memory (it came with 1 GB) and Thai Keyboard (Thai Keyboard is the American Keyboard with the Thai Alphabet) which works just fine.
I'd like to install Windows 7 in a new partition and a dual boot with the existing Windows XP. The problem is that It's not possible to create a partition on the C: disk. I've been trying with EASEUS Partition Master, Partition Manager 10 Express and none of them let me do it, only Resizing/Moving the existing partition is an option.
Hard disk looks as follows:
C: Type: NTFS | Size 103.91 GB | Used: 29.49 GB | Unusued: 79.42 GB | Status: System | Pri/Log: Primary
D: (Lenovo) Type: NTFS | Size 30.38 GB | Used: 1.44 GB | Unusued: 28.95 GB | Status: None| Pri/Log: Logical
*: (Hidden) Type: NTFS | Size 14.75 GB | Used: 4.88 GB | Unusued: 9.87 GB | Status: None| Pri/Log: Primary
After search the forums I didn't find a solution.
I've read elsewhere that Windows des not allow more than 3 partitions. Is there a safe way to partition the C: volume which has Windows XP and Install Windows Seven along with it?
Thanks in advance,
George
Solved!
Go to Solution.

Hi,
be sure that you backup your system.... partitioning and resizing is always on risk...
be sure that you can restore if something goes wrong...
if you dont know what happens ... dont do this...
first you can have 3 active (primary & 1 logical ..
as i have for example 1.XP,2. Win7,3. Ubuntu...and 4. Logical (for common data like music,video,textfiles,picture and...)
or 4 active primary...(..)
...hope that you knows easeus partitionmanager a bit ...
...lets have a look :
so you have ... partition c: (XP) ..... ca. 70 GB .... thats enough room for windows 7...(prefer 30GB workspace)
start in windows ... start easeus PM .. click on drive c: (XP) and resize to ... GB leave 30 GB black space behind..(for W7)..
go on this empty space create new primary NTFS partition ... and after that , right click on new primary drive set active !!!! .... click apply button and cross fingers
... system will restart and easeus will manage all your changes takes time...
after restart... prepared for booting windows 7 install and if windows asking you , take the second partition on your harddrive (30 GB)..... and ....so on...
thats the way to go ...
sincerely KalvinKlein
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

What do i need to do to share TB and Lightning files between W7 and Ubuntu 14.04 on a dual boot system?

I recently installed Ubuntu 14.04 alongside W7. Since I'm not comfortable dropping Windows completely yet, I want my W7 Thunderbird and my Ubuntu TB to have access to the same data file holding current messages, so I don't have to get out of one to use TB on the other. I rely on Lightning and also want my reminders to be consistent from either OS. I have a separate NTFS data partition which, I understand, can be used to house the profile directory (though I've not seen that as a solution for Lightning).
In trying to set it up, I've run into questions that I can't find a good answer for -- want sources that address the problem and are recent. I'm pretty patient, and I can stumble through a lot of things (like learningn about partitions). But I'm not a programmer, and this start-stop-sort-through-dozens-of-old-incomplete-and-irrelevant-answers process is frustrating. (Nor do I lift the hood and tune my own car engine.) I also recognize that some things I want to do aren't necessarily common, so they're not at the top of anyone's "tell the world how to do this" list.
1. My profiles directory has 6 *.default files. I assume the current one is the most recent. Do I need the older ones? How did I get them, since I've never knowingly created a new one? I'm the only user of my machine and thus the only user for TB.
2. I saw the following before setting up the dual boot system, so it's likely not related -- but if someone who knows TB well can comment I'll appreciate it: when I view All folders, I see 58(!) folders with names nstmp-##. The contents overlap with normally-named folders, but the sets of messages are not identical. Do these indicate a problem and/or should I change something? Does this have to do with compacting or archiving, neither of which I do? Never saw the need, and never saw an article saying that they're important. I just want to use mail and reminders. And BTW I've been using TB/Lightning for years and am Very happy with them, so I want to keep using them.
3. Is there a way to set up Lightning to hit the same data file(s) on my data partition? Or somewhere? Where are Lightning's files? I remember one source mentioned linking to "storage.sdb", but (1) I can't find the reference again, and (2) links to some of my files don't always work. Broken links aren't Mozilla's problem, but someone might know how to geet around the problem for the sake of Lightning. Also, storage.sdb and calendar* directories exist inside my *.default profile directory -- so why would I need to link anything? Are these not where calendar data is stored? If not, where?
I'd rather understand the reasons behind recommended procedures ("do A because Y is how Lightning/TB works" -- vs "do A, then B, then C...and it will/should(!) work."). But if you can point me to a clear procedure that will get me where I want to go, that will be enough.
Last, the following two URLs looked like they would help but don't -- so you don't need to point me to them again:
http://kb.mozillazine.org/Sharing_a_profile_between_Windows_and_Linux -- this is only 2 years old but:
(1) it only says that "settings" specify file locations, without saying which settings. Stumbling around, I found "Local directories" under Server Settings. For more detail the page refers to an article that's 10 years old. Neither source says which subdirectory under *.default should be the target. The older one references ".../mail", but when I enter that value in Local Directories under Ubuntu, nothing shows up. When I went down one more level to "/Local Folders", the folders appear and the new-message counts seem(!) ok. But I also got a couple "folder missing...will adjust filters" messages. I never got those under Windows. So am I good to go, or am I missing messages?
(2) The above page only says that Lightning is a "potential problem", with no suggestion of a solution or link to a discussion. Searching results in many hits, but I haven't found anything helpful.
http://ubuntuforums.org/showthread.php?t=1624973 -- this looked promising, but the comments are dated 2009-2010, deal with ubuntu 10 and XP, and don't seem to address my problem -- unless I'm not savvy enough to recognize it, which is entirely possible.
Thanks for any insights.

Lightning is a problem for you because it hooks into Thunderbird at a low level and you need a version compiled for the platform Thunderbird is running on. So you can't do the preferred solution, which is to put your whole profile in a shared folder and have both instances of Thunderbird reference the same profile. (Ditto for Enigmail). Lightning may become an integral part of Thunderbird in an upcoming release, at which point this limitation due to Lightning should disappear.
And if you can't use a shared profile, you can't set your Lightning, or your Address Book, to share a common set of files. Put another way, the linkage from Thunderbird to its address book files and calendar data is hard-coded, and not exposed where we can adjust it. :-(
The halfway house is to place your mail stores in a shared place, and use the Local Directory setting in each account's settings to connect to it. They don't need to be in the profile; what's more important in your case is that they are in a folder accessible to both operating systems.
Look in your profile; everything under Mail and ImapMail needs to be moved out to a shared folder. Note the entries in Thunderbird under Local Directory before you do this, and reconstruct those pathnames in Thunderbird, but adjusted to suit their new locations.
(You can see here that you need to make many adjustments, one per account, in each instance of Thunderbird, so it's a high-maintenance solution and this is why we don't recommend it when the alternative, moving the whole profile, is possible.)
I share address books and calendars between Thunderbirds on various computers (and my phone and tablet) by syncing to something in the cloud; Google Contacts and Google Calendar are my choices, using gContactSync and CalDav.
Having made the break myself some years ago, I'd recommend you break away from Windows. ;-)

Arch & Windows 8 Dual Boot -- Windows Boot Loader loads grub-rescue

Arch works fine,but as it always happens Windows boot went down. Both OS are EFI.
Note that boot secure and fast boot were disabled for Windows 8.
I used os-prober, but did not fix anything; so, I removed it. I tried to hack things out using boot-repair from Ubuntu, but it requires a repository, grub-efi, from Ubuntu that Arch doesn't have.
I am trying to modify files in grub.d and grub.cfg and hopefully fix something.
Exact description:
- archgrub loads and shows 3 entries. Two for Arch that load the sys succesfully and one for Windows 8 that fails.
- When I try to execute Windows from grub, it brings me to a grub rescue>
and shows error /boot/grub/x86_64-efi/normal.mod not found
As far as I am concerned this .mod is from Linux, so I don't know why it is being called into Windows loading procedures.
lsblk returns:
[jav@localhost ~]$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 931.5G 0 disk
|-sda1 8:1 0 1000M 0 part
|-sda2 8:2 0 260M 0 part
|-sda3 8:3 0 1000M 0 part
|-sda4 8:4 0 128M 0 part
|-sda5 8:5 0 605.3G 0 part
|-sda6 8:6 0 5.4G 0 part /boot/efi
|-sda7 8:7 0 25G 0 part
|-sda8 8:8 0 20G 0 part
|-sda9 8:9 0 244.1G 0 part /
`-sda10 8:10 0 29.3G 0 part
sr0 11:0 1 1024M 0 rom
Here's the output of fdisk. Another weird thing is that sometimes ubuntu would show on my terminal. See the first line below, "jav@ubuntu"?!
[jav@ubuntu ~]$ sudo fdisk -l
[sudo] password for jav:
Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: [i deleted this]
Device Start End Size Type
/dev/sda1 2048 2050047 1000M Windows recovery environment
/dev/sda2 2050048 2582527 260M EFI System
/dev/sda3 2582528 4630527 1000M unknown
/dev/sda4 4630528 4892671 128M Microsoft reserved
/dev/sda5 4892672 1274335231 605.3G Microsoft basic data
/dev/sda6 1847777280 1859151871 5.4G EFI System
/dev/sda7 1859151872 1911580671 25G Microsoft basic data
/dev/sda8 1911580672 1953523711 20G Windows recovery environment
/dev/sda9 1335775232 1847777279 244.1G Linux filesystem
/dev/sda10 1274335232 1335775231 29.3G Microsoft basic data
And, bootinfoscript output:
Boot Info Script 0.61 [1 April 2012]
============================= Boot Info Summary: ===============================
=> No boot loader is installed in the MBR of /dev/sda.
sda1: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda2: __________________________________________________________________________
File system: vfat
Boot sector type: Windows 7: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/Boot/bkpbootx64.efi /efi/Boot/bootx64.efi
/efi/ubuntu/grubx64.efi
sda3: __________________________________________________________________________
File system: vfat
Boot sector type: Windows 7: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/Boot/bkpbootx64.efi /efi/Boot/bootx64.efi
/efi/ubuntu/grubx64.efi /bootmgr /boot/bcd
sda4: __________________________________________________________________________
File system:
Boot sector type: -
Boot sector info:
Mounting failed: mount: unknown filesystem type ''
sda5: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe
sda6: __________________________________________________________________________
File system: vfat
Boot sector type: SYSLINUX 6.02 ... :..(:,:0:4:8:....D:H:L:[.T:[.\:`:d:[.l:p:t:x:|:.:.:.:.:.:.:.:.....................
Boot sector info: Syslinux looks at sector 99102 of /dev/sda6 for its
second stage. SYSLINUX is installed in the /syslinux
directory. No errors found in the Boot Parameter Block.
Operating System:
Boot files: /grub/grub.cfg /syslinux/syslinux.cfg
/syslinux/ldlinux.sys
sda7: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda8: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda9: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Arch Linux ()
Boot files: /etc/fstab
sda10: _________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System:
Boot files:
============================ Drive/Partition Info: =============================
Drive: sda _____________________________________________________________________
Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sda1 1 1,953,525,167 1,953,525,167 ee GPT
GUID Partition Table detected.
Partition Start Sector End Sector # of Sectors System
/dev/sda1 2,048 2,050,047 2,048,000 Windows Recovery Environment (Windows)
/dev/sda2 2,050,048 2,582,527 532,480 EFI System partition
/dev/sda3 2,582,528 4,630,527 2,048,000 -
/dev/sda4 4,630,528 4,892,671 262,144 Microsoft Reserved Partition (Windows)
/dev/sda5 4,892,672 1,274,335,231 1,269,442,560 Data partition (Windows/Linux)
/dev/sda6 1,847,777,280 1,859,151,871 11,374,592 EFI System partition
/dev/sda7 1,859,151,872 1,911,580,671 52,428,800 Data partition (Windows/Linux)
/dev/sda8 1,911,580,672 1,953,523,711 41,943,040 Windows Recovery Environment (Windows)
/dev/sda9 1,335,775,232 1,847,777,279 512,002,048 Data partition (Linux)
/dev/sda10 1,274,335,232 1,335,775,231 61,440,000 Data partition (Windows/Linux)
"blkid" output: ________________________________________________________________
Device UUID TYPE LABEL
/dev/sda1 CE62D9F062D9DCF1 ntfs WINRE_DRV
/dev/sda10 150a8788-6049-45ed-85af-ded92a2c0801 ext4
/dev/sda2 16DC-8816 vfat SYSTEM_DRV
/dev/sda3 7CDD-0403 vfat LRS_ESP
/dev/sda4
/dev/sda5 40E4E0CFE4E0C7EC ntfs Windows8_OS
/dev/sda6 9C3F-2A9E vfat
/dev/sda7 7240E43740E40427 ntfs LENOVO
/dev/sda8 422CE5EA2CE5D945 ntfs PBR_DRV
/dev/sda9 1a765403-f251-43d8-8edf-c191475d3837 ext4
================================ Mount points: =================================
Device Mount_Point Type Options
/dev/sda6 /boot vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/sda6 /boot/efi vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/sda9 / ext4 (rw,relatime,data=ordered)
============================= sda6/grub/grub.cfg: ==============================
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt9'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 1a765403-f251-43d8-8edf-c191475d3837
else
search --no-floppy --fs-uuid --set=root 1a765403-f251-43d8-8edf-c191475d3837
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
## Attempt at fixing grub
# insmod fat
# set root='hd0,gpt6'
### BEGIN /etc/grub.d/30_os-prober ###
#menuentry 'Windows Boot Manager (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-efi-16DC-8816' {
# insmod part_gpt
# insmod fat
# set root='hd0,gpt2'
# if [ x$feature_platform_search_hint = xy ]; then
# search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 16DC-8816
# else
# search --no-floppy --fs-uuid --set=root 16DC-8816
# fi
# chainloader /EFI/Microsoft/Boot/bootmgfw.efi
menuentry "Windows 8 UEFI" {
set root='(hd0,gpt2)'
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
### BEGIN /etc/grub.d/60_memtest86+ ###
### END /etc/grub.d/60_memtest86+ ###
========================= sda6/syslinux/syslinux.cfg: ==========================
# Config file for Syslinux -
# /boot/syslinux/syslinux.cfg
# Comboot modules:
# * menu.c32 - provides a text menu
# * vesamenu.c32 - provides a graphical menu
# * chain.c32 - chainload MBRs, partition boot sectors, Windows bootloaders
# * hdt.c32 - hardware detection tool
# * reboot.c32 - reboots the system
# To Use: Copy the respective files from /usr/lib/syslinux to /boot/syslinux.
# If /usr and /boot are on the same file system, symlink the files instead
# of copying them.
# If you do not use a menu, a 'boot:' prompt will be shown and the system
# will boot automatically after 5 seconds.
# Please review the wiki: https://wiki.archlinux.org/index.php/Syslinux
# The wiki provides further configuration examples
DEFAULT arch
PROMPT 0 # Set to 1 if you always want to display the boot: prompt
TIMEOUT 50
# You can create syslinux keymaps with the keytab-lilo tool
#KBDMAP de.ktl
# Menu Configuration
# Either menu.c32 or vesamenu32.c32 must be copied to /boot/syslinux
UI menu.c32
#UI vesamenu.c32
# Refer to http://syslinux.zytor.com/wiki/index.php/Doc/menu
MENU TITLE Arch Linux
#MENU BACKGROUND splash.png
MENU COLOR border 30;44 #40ffffff #a0000000 std
MENU COLOR title 1;36;44 #9033ccff #a0000000 std
MENU COLOR sel 7;37;40 #e0ffffff #20ffffff all
MENU COLOR unsel 37;44 #50ffffff #a0000000 std
MENU COLOR help 37;40 #c0ffffff #a0000000 std
MENU COLOR timeout_msg 37;40 #80ffffff #00000000 std
MENU COLOR timeout 1;37;40 #c0ffffff #00000000 std
MENU COLOR msg07 37;40 #90ffffff #a0000000 std
MENU COLOR tabmsg 31;40 #30ffffff #00000000 std
# boot sections follow
# TIP: If you want a 1024x768 framebuffer, add "vga=773" to your kernel line.
LABEL arch
MENU LABEL Arch Linux
LINUX ../vmlinuz-linux
APPEND root=/dev/sda3 rw
INITRD ../initramfs-linux.img
LABEL archfallback
MENU LABEL Arch Linux Fallback
LINUX ../vmlinuz-linux
APPEND root=/dev/sda3 rw
INITRD ../initramfs-linux-fallback.img
#LABEL windows
# MENU LABEL Windows
# COM32 chain.c32
# APPEND hd0 1
LABEL hdt
MENU LABEL HDT (Hardware Detection Tool)
COM32 hdt.c32
LABEL reboot
MENU LABEL Reboot
COM32 reboot.c32
LABEL poweroff
MENU LABEL Poweroff
COM32 poweroff.c32
=================== sda6: Location of files loaded by Grub: ====================
GiB - GB File Fragment(s)
================= sda6: Location of files loaded by Syslinux: ==================
GiB - GB File Fragment(s)
============== sda6: Version of COM32(R) files used by Syslinux: ===============
syslinux/cat.c32 : not a COM32/COM32R module
syslinux/chain.c32 : not a COM32/COM32R module
syslinux/cmd.c32 : not a COM32/COM32R module
syslinux/config.c32 : not a COM32/COM32R module
syslinux/cptime.c32 : not a COM32/COM32R module
syslinux/cpuid.c32 : not a COM32/COM32R module
syslinux/cpuidtest.c32 : not a COM32/COM32R module
syslinux/debug.c32 : not a COM32/COM32R module
syslinux/disk.c32 : not a COM32/COM32R module
syslinux/dmitest.c32 : not a COM32/COM32R module
syslinux/elf.c32 : not a COM32/COM32R module
syslinux/ethersel.c32 : not a COM32/COM32R module
syslinux/gfxboot.c32 : not a COM32/COM32R module
syslinux/gpxecmd.c32 : not a COM32/COM32R module
syslinux/hdt.c32 : not a COM32/COM32R module
syslinux/hexdump.c32 : not a COM32/COM32R module
syslinux/host.c32 : not a COM32/COM32R module
syslinux/ifcpu.c32 : not a COM32/COM32R module
syslinux/ifcpu64.c32 : not a COM32/COM32R module
syslinux/ifmemdsk.c32 : not a COM32/COM32R module
syslinux/ifplop.c32 : not a COM32/COM32R module
syslinux/kbdmap.c32 : not a COM32/COM32R module
syslinux/kontron_wdt.c32 : not a COM32/COM32R module
syslinux/ldlinux.c32 : not a COM32/COM32R module
syslinux/libcom32.c32 : not a COM32/COM32R module
syslinux/libgpl.c32 : not a COM32/COM32R module
syslinux/liblua.c32 : not a COM32/COM32R module
syslinux/libmenu.c32 : not a COM32/COM32R module
syslinux/libutil.c32 : not a COM32/COM32R module
syslinux/linux.c32 : not a COM32/COM32R module
syslinux/ls.c32 : not a COM32/COM32R module
syslinux/lua.c32 : not a COM32/COM32R module
syslinux/mboot.c32 : not a COM32/COM32R module
syslinux/meminfo.c32 : not a COM32/COM32R module
syslinux/menu.c32 : not a COM32/COM32R module
syslinux/pcitest.c32 : not a COM32/COM32R module
syslinux/pmload.c32 : not a COM32/COM32R module
syslinux/poweroff.c32 : not a COM32/COM32R module
syslinux/prdhcp.c32 : not a COM32/COM32R module
syslinux/pwd.c32 : not a COM32/COM32R module
syslinux/pxechn.c32 : not a COM32/COM32R module
syslinux/reboot.c32 : not a COM32/COM32R module
syslinux/rosh.c32 : not a COM32/COM32R module
syslinux/sanboot.c32 : not a COM32/COM32R module
syslinux/sdi.c32 : not a COM32/COM32R module
syslinux/sysdump.c32 : not a COM32/COM32R module
syslinux/vesainfo.c32 : not a COM32/COM32R module
syslinux/vesamenu.c32 : not a COM32/COM32R module
syslinux/vpdtest.c32 : not a COM32/COM32R module
syslinux/whichsys.c32 : not a COM32/COM32R module
syslinux/zzjson.c32 : not a COM32/COM32R module
=============================== sda9/etc/fstab: ================================
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda9
UUID=1a765403-f251-43d8-8edf-c191475d3837 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda6
#UUID=9C3F-2A9E /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
UUID=9C3F-2A9E /boot vfat defaults 0 2
UUID=9C3F-2A9E /boot/efi vfat defaults 0 1
============== sda9: Version of COM32(R) files used by Syslinux: ===============
boot/syslinux/cat.c32 : not a COM32/COM32R module
boot/syslinux/chain.c32 : not a COM32/COM32R module
boot/syslinux/cmd.c32 : not a COM32/COM32R module
boot/syslinux/config.c32 : not a COM32/COM32R module
boot/syslinux/cptime.c32 : not a COM32/COM32R module
boot/syslinux/cpuid.c32 : not a COM32/COM32R module
boot/syslinux/cpuidtest.c32 : not a COM32/COM32R module
boot/syslinux/debug.c32 : not a COM32/COM32R module
boot/syslinux/disk.c32 : not a COM32/COM32R module
boot/syslinux/dmitest.c32 : not a COM32/COM32R module
boot/syslinux/elf.c32 : not a COM32/COM32R module
boot/syslinux/ethersel.c32 : not a COM32/COM32R module
boot/syslinux/gfxboot.c32 : not a COM32/COM32R module
boot/syslinux/gpxecmd.c32 : not a COM32/COM32R module
boot/syslinux/hdt.c32 : not a COM32/COM32R module
boot/syslinux/hexdump.c32 : not a COM32/COM32R module
boot/syslinux/host.c32 : not a COM32/COM32R module
boot/syslinux/ifcpu.c32 : not a COM32/COM32R module
boot/syslinux/ifcpu64.c32 : not a COM32/COM32R module
boot/syslinux/ifmemdsk.c32 : not a COM32/COM32R module
boot/syslinux/ifplop.c32 : not a COM32/COM32R module
boot/syslinux/kbdmap.c32 : not a COM32/COM32R module
boot/syslinux/kontron_wdt.c32 : not a COM32/COM32R module
boot/syslinux/ldlinux.c32 : not a COM32/COM32R module
boot/syslinux/libcom32.c32 : not a COM32/COM32R module
boot/syslinux/libgpl.c32 : not a COM32/COM32R module
boot/syslinux/liblua.c32 : not a COM32/COM32R module
boot/syslinux/libmenu.c32 : not a COM32/COM32R module
boot/syslinux/libutil.c32 : not a COM32/COM32R module
boot/syslinux/linux.c32 : not a COM32/COM32R module
boot/syslinux/ls.c32 : not a COM32/COM32R module
boot/syslinux/lua.c32 : not a COM32/COM32R module
boot/syslinux/mboot.c32 : not a COM32/COM32R module
boot/syslinux/meminfo.c32 : not a COM32/COM32R module
boot/syslinux/menu.c32 : not a COM32/COM32R module
boot/syslinux/pcitest.c32 : not a COM32/COM32R module
boot/syslinux/pmload.c32 : not a COM32/COM32R module
boot/syslinux/poweroff.c32 : not a COM32/COM32R module
boot/syslinux/prdhcp.c32 : not a COM32/COM32R module
boot/syslinux/pwd.c32 : not a COM32/COM32R module
boot/syslinux/pxechn.c32 : not a COM32/COM32R module
boot/syslinux/reboot.c32 : not a COM32/COM32R module
boot/syslinux/rosh.c32 : not a COM32/COM32R module
boot/syslinux/sanboot.c32 : not a COM32/COM32R module
boot/syslinux/sdi.c32 : not a COM32/COM32R module
boot/syslinux/sysdump.c32 : not a COM32/COM32R module
boot/syslinux/vesainfo.c32 : not a COM32/COM32R module
boot/syslinux/vesamenu.c32 : not a COM32/COM32R module
boot/syslinux/vpdtest.c32 : not a COM32/COM32R module
boot/syslinux/whichsys.c32 : not a COM32/COM32R module
boot/syslinux/zzjson.c32 : not a COM32/COM32R module
======================== Unknown MBRs/Boot Sectors/etc: ========================
Unknown GPT Partiton Type
e7afbfbf4fa38a449a5b6213eb736c22
========= Devices which don't seem to have a corresponding hard drive: =========
sdb
=============================== StdErr Messages: ===============================
cat: /tmp/BootInfo-p9ML2Cte/Tmp_Log: No such file or directory
cat: /tmp/BootInfo-p9ML2Cte/Tmp_Log: No such file or directory
/dev/cdrom: open failed: No medium found
/dev/sdb: open failed: No medium found
No volume groups found
mdadm: No arrays found in config file or automatically
Any ideas?
Here's my grub.cfg:
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt9'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 1a765403-f251-43d8-8edf-c191475d3837
else
search --no-floppy --fs-uuid --set=root 1a765403-f251-43d8-8edf-c191475d3837
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/30_os-prober ###
menuentry 'Windows Boot Manager (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-efi-16DC-8816' {
insmod part_gpt
insmod fat
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 16DC-8816
else
search --no-floppy --fs-uuid --set=root 16DC-8816
fi
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
### BEGIN /etc/grub.d/60_memtest86+ ###
### END /etc/grub.d/60_memtest86+ ###
Last edited by knowNothing23 (2013-12-30 00:17:02)

Hi,
New to this forum, joined today in anticipation of trying an install of AL...For whatever this may be worth:
I have an HP Pavillion desktop that came with Windows 8 (now 8.1), & has, of course, a UEFI boot system. I tried earlier to install Ubuntu Studio (which I currently run) on the same disk as Windows (/dev/sda), I made (I believe) a huge mistake in trying to install as LVM/ext4... wiped out my Windows install & made the UEFI unavailable... I had to do a complete re-install of Windows (fortunately, I did the recommended system backup, using 4 DVD's!) so then I tried a (non LVM) install on an external usb 3.0, with the Grub 2 on the external disk (great access time, & it worked fine... IMO)...
One other item: as I have been trying to find the right flavor of Linux for my main purposes, I have been trying various distros. & having to try to learn to negotiate the UEFI, secure/legacy procedures (still learning)... As I was unsure of installing rEFind... I did down load the .iso, burn it to a CD...
http://www.rodsbooks.com/refind/getting.html
& in legacy mode, found that simply putting it (rEFind CD into the CD/DVD player, which in the UEFI it is labeled something like HP/UEFI CD/DVD), & then launching it, rEFind worked for some other distros...that is, I was able to boot into my Linux distros, even bypassing Grub), as well as having the option of booting Windows. It may seem trivial that I say this (it maybe is), but I have not seen anywhere (I have scoured the internet rather well) this mentioned as a possibility (though it, of course, would not make such a good permanent solution, especially for computers like mine that have only one CD/DVD player).
HenryP

How can I share ONE thunderbird profile between XP x64 and Windows 7 dual booting on the same machine?

I have a primary XP profile and associated mailboxes/accounts. I am dual-booting to Windows 7 and want to share only that XP profile so that all of my mail appears (and is synchronized) in the Thunderbird browser regardless of which OS I boot to. This seems as simple as pointing the Win 7 mail account local profile to the original XP profile, but that doesn't work. And - please - don't point this question to the response regarding sharing profiles between windows and Linux. That thread hasn't helped. Thanks in advance

Well I have no idea hat thread your talking about, but regardless the process is always the same, use the profile manager to create a new profile and point the profile manager to the profile you wish to use.
see https://support.mozilla.org/en-US/kb/profiles-tb#w_restoring-a-profile-backup
and
http://kb.mozillazine.org/Moving_your_profile_folder_-_Thunderbird

Windows 7 dual-boot query

Hi there!
I am in the process of selling my old Windows 7 laptop and I'm very much considering to buy my very first MacBook Pro laptop. Now, I heard that one can install Windows 7 OS as a dual-boot to Mac OS X. Can I ask:
1. Will I need an actually physical Windows 7 disc to install it in my MBP? Is it that easy to install? Roughly how long will it take to install?
2. Will dual-boot mean that it might slowdown the MBP's performance and running?
3. With Windows 7 boot camp will the multi-gesture functionality of Mac OS X be "applicable" in the Windows OS?
Thank you.

onslaught wrote:
1. Will I need an actually physical Windows 7 disc to install it in my MBP?
Yes
Is it that easy to install?
Easy for most
Roughly how long will it take to install?
A hour or so.
Will dual-boot mean that it might slowdown the MBP's performance and running?
No, dual boot is chosing one operating system or the other when booting.
With Windows 7 boot camp will the multi-gesture functionality of Mac OS X be "applicable" in the Windows OS?
Not all no, Apple bridges some but not all the gestures are supported in Win 7 or their software.
Read:
Windows in BootCamp or Virtual Machine?

T400s Linux/Windows dual boot with Linux from Esata Flash Drive

This project is about a dual boot Windows/Linux system without using the normal dual boot changes in the bootloader of the windows hard drive. When I started this I found bits and pieces of information on the web but no complete description so I wrote this post.
I have done a dual boot system on my previous Thinkpad where I had partitioned the hard drive between Linux and windows. For this project I wanted to leave the windows hard drive absolutely intact and unaltered, and boot Linux from a flash drive in the esata port on the back of the T400s. Obviously this uses the F12 boot list function key to boot from the flash. The advantage of this is that Windows is totally unaltered and when I need Linux, I plug in the esata flash drive, hit F12 during the boot cycle and select booting from the esata flash drive. The reason for Esata rather than USB is simply speed. I have a nice fast Linux installation.
I used the OCZ esata flash drive but suspect any of the alternatives will work. It did not need the accessory usb cable because the Thinkpad powered the esata flash directly.
To boot from the esata drive I had to make the following changes in the bios
    I left the esata flash plugged in as I went into the bios
    Bios>config>Serial ATA and changed the Sata controller mode option to compatibility
    Restart and back into the Bios
    Bios>startup>boot - in my case the esata flash drive showed up as ATA HDD2 and was excluded from the boot order so I had to un-exclude it and move it to the point in the boot order that I wanted.
Next I downloaded a linux installation iso and put it on a CD - in my case opensuse. Then booted from the CD
From now on this instructions are specific to opensuse and yast but can be generalized to whatever Linux is being used.
In my case yast came up with a good set of suggestions for automatically partitioning the flash drive but then crashed during the partitioning itself. So I rebooted and specified the partitions manually.
    A fat32 partition left as a partition which both windows and Linux could see (in my case about 20% of the drive) (/dev/sdb1)
    An extended partition with the remainder of the drive (/dev/sdb2) which contains the following logical partitions
    A linux Swap partition of 2GB (/dev/sdb5)
    A linux /home partition –the remainder of the drive (/dev/sdb6)
    A linux /root partition of 8GB (/dev/sdb7)
Yast automatically suggested mount points of C,D,E for the windows partitions. Unfortunately because of the way the Thinkpad hard drive was laid out Yast had C assigned the ThinkPad Service partition and D assigned to the SW_Preload (or main windows partition). However there was an edit function that allows for the reversal of those mount points so that the windows C drive is mounted in Linux as Windows/C thereby avoiding confusion. I had already backed up and removed the Thinkpad factory install data so I did not have to deal with that. Yast suggested Windows/E for the mount point of the FAT32 partition on the flash drive, which I accepted.
The yast install configurator made all this manual selection easy, and after the manual configuration the partitioning worked perfectly.
Next step was Linux user configuration which went fine
Next was booting.
In the section management tab
    delete the windows 1 and 2 options (since we are not dual booting directly)
In the boot loader installation tab
    uncheck boot from mbr ( this stops the install from installing Grub and dual boot on the windows c drive
    check boot from root partition (this installs grub and all associated files in the Linux root partition (/dev/sdb6)
I believe that the correct procedure at this point is to click Boot Loader installation details which will bring up the Grub device map. In the device map there will be a line for the fixed hard drive (aka the windows drive) and a line for the esata flash drive. When the installer started up these were in hard drive and esata drive order. However when we boot directly from the flash the esata drive will be grub drive hd0 and the fixed hard drive will be grub hd1. The device map order needs to be changed to reflect this ie the esata drive should be first not second.
I did not do this and ended up initially doing Grub command line editing to boot and later manually editing the grub files using information I had previously learned the hard way and through google.
At this point let the installer go ahead and install Linux. After doing this it should come back and tell you to reboot. Do not do it yet because we need to install the MBR into the flash drive.
I suspect that there is a way of doing this in Yast running from the Live CD but it was not obvious to me so I used the manual method that I have used before.
Open a root terminal
Mount /dev/sdb6 to /mnt/sdb6 (my linux root)
Touch /mnt/sdb6/boot/grub/flag
The purpose of this is when we go looking later at the grub command prompt we need an easy to find unique file
Start grub and do the following
#grub
            grub> find /boot/grub/flag
                (hd1,5)    -- the result of the find in my example
            grub> root (hd1,5)   -- using the result of the find in my example
            grub> setup (hd1)   -- install mbr -- my example parameters - if you get this wrong you will trash some other drive!!!
                  hopefully grub announces success
            grub> quit
Reboot and select the flash drive. In my case I still had the grub devicemap wrong and had to edit the grub commands during boot to tell grub how to find the correct partition and then edit them again after booting
Typical linux install issues that we all always seem to have and can be solved with a little (or a lot of) google research.
As I said at the beginning I now have an untouched windows installation and a nice fast Linux installation. I hope that this will be of some use to someone.

Hi chrissh
i tried this exact procedure... on the exact same notebook (T400s). However, as soon as I set the
   Bios>config>Serial ATA to "compatibility", I cannot use my default Windows installation! I immediately get the "blue screen of death".
I doubt I did anything differently since this is the first step of your procedure and my laptop is brand new!
any idea?

How do you uninstall Windows 10 Dual Boot?

Hello,
I am running a dual boot installation of Winodws 8.1 and 10 Techical Preview, and I like to know how do you uninstall the Windows 10 from the dual boot scheme? I think I've uninstalled previous beta versions of windows 8 by erasing the partition it
was installed into and that was it. Is this the correct way to remove window 10 too? Just asking, since the graphical version of the OS boot screen is present in this dual boot installation, does that change anything.

Hello,
I am running a dual boot installation of Winodws 8.1 and 10 Techical Preview, and I like to know how do you uninstall the Windows 10 from the dual boot scheme? I think I've uninstalled previous beta versions of windows 8 by erasing the partition it
was installed into and that was it. Is this the correct way to remove window 10 too? Just asking, since the graphical version of the OS boot screen is present in this dual boot installation, does that change anything.
Logon to your Win 8.1 > press the Win logo key and R key . You are now at Run window> at the Run box type diskmgmt.msc > OK
You are now at Disk Management window > right click at the partition that house your Win 10 TP > click Delete Volume > the partition is now UNALLOCATED.
At the left of it is your Win 8.1 partition. Yes ?
If yes, right click at Win 8.1 partition > click Extend Volume > click Next > at Select the amount of space in MB, type in the maximum available space shown for the unallocated space in MB > Next > Finish
The space shrunk for Win 10 partition is now back to your Win 8.1

Arch And Windows 7 Dual Boot On Separate HDD

Hi everyone.
Firstly, a big thank you to everyone for helping me out in my first thread regarding choice of partitions and filesystems.
I went on to install Arch today on my second HDD (160GB). My first HDD has Windows 7 installed on it. (The BIOS shows that the HDD with Win 7 installed is HDD1.)
Arch showed the HDDs as sda and sdb. I was installing on sdb and created my partitions accordingly.
sdb1 --> root (15GB)
sdb2 --> swap (1GB)
sdb3 --> var (10GB)
sdb4 --> home (remaining space)
I had to flag sdb1 as Bootable.
Then I was asked about mountpoints and something about selecting by dev or uuid. I didn't quite understand but selected dev. Then formatted with ext4. Did not add any parameters.
Before proceeding they gave a warning about no /boot partition but I continued anyway.
It was an FTP install and went pretty smoothly. I configured everything exactly as I had read in the guides online and Wiki. GRUB said it configured successfully (I did not make any chnges to it). I had put GRUB on sdb and not on any partition.
As I rebooted, my system did not show the GRUB but went straight on to Windows 7. I went into BIOS and changed my first drive to the 160GB Seagate where I had installed Arch and rebooted. This time GRUB came up without any option to boot Windows 7. When I selected Arch it gave an error and did not boot.
So I'm back on Windows 7 and need help. I'm a noob and did not much understand the solution that I saw on another thread. Since I intend to have the 2 OSs on separate drives and dual boot, what should I do?
Will be very grateful for any help.
Last edited by Ritwik7 (2010-06-06 12:01:31)

Here you go:
# Config file for GRUB - The GNU GRand Unified Bootloader
# /boot/grub/menu.lst
# DEVICE NAME CONVERSIONS
# Linux Grub
# /dev/fd0 (fd0)
# /dev/sda (hd0)
# /dev/sdb2 (hd1,1)
# /dev/sda3 (hd0,2)
# FRAMEBUFFER RESOLUTION SETTINGS
# +-------------------------------------------------+
# | 640x480 800x600 1024x768 1280x1024
# ----+--------------------------------------------
# 256 | 0x301=769 0x303=771 0x305=773 0x307=775
# 32K | 0x310=784 0x313=787 0x316=790 0x319=793
# 64K | 0x311=785 0x314=788 0x317=791 0x31A=794
# 16M | 0x312=786 0x315=789 0x318=792 0x31B=795
# +-------------------------------------------------+
# for more details and different resolutions see
# http://wiki.archlinux.org/index.php/GRUB#Framebuffer_Resolution
# general configuration:
timeout 5
default 0
color light-blue/black light-cyan/blue
# boot sections follow
# each is implicitly numbered from 0 in the order of appearance below
# TIP: If you want a 1024x768 framebuffer, add "vga=773" to your kernel line.
# (0) Windows
title Windows
rootnoverify (hd1,0)
makeactive
chainloader +1
# (1) Arch Linux
title Arch Linux
root (hd0,0)
kernel /vmlinuz26 root=/dev/mapper/vghparch-lvroot ro quiet
initrd /kernel26.img
# (2) Arch Linux
title Arch Linux Fallback
root (hd0,0)
kernel /vmlinuz26 root=/dev/mapper/vghparch-lvroot ro
initrd /kernel26-fallback.img
I installed grub on the second hdd and configured the bios so this drive comes first in the boot sequence and as pyther pointed out above the drive where grub is loaded from becomes hd0.
Last edited by Ashren (2010-06-07 18:51:29)

Windows XP - Dual Boot for Satellite U300-134

Hi. I have read the other replies to this problem of adding Windows XP (as a dual boot) but it still won't work. My laptop (I bought a few days ago) comes with Vista, and I bought Windows XP Home Edition - OEM. I got the intel matrix storage manager onto a USB floppy drive, but now it gives a message that "The file txtsetup.oem could not be found". I have to have XP because it turns out my work VPN will not run under Vista (I found that out AFTER I bought the computer unfortunately).
Can you please tell me what I need to do next to get this working? And any other surprises I might come across? I have looked round the internet but can't find the answers to this. I tried nlite but haven't managed to get that working yet either.
Thank you.
Ian

Hi
There are different reasons why you cannot install the Win XO on the U300.
First of all do you use the right Intel Matrix Storage manager?
You notebook seems to support the Intel GM965 + Intel ICH8M chipset!!!
Please check this thread!
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=26040
User Markus77 has listed the details!
Furthermore please dont format the HDD or create any partitions AFTER installation of the Intel Matrix Storage manager. This would delete the already installed driver.

Solaris 10 & Windows 2K dual boot

Hello forum,
I installed Solaris 10 on a machine such that it dual boots with Win2K . All seemed well , I logged into Solaris and Win 2K and it worked properly .
I tried logging into JDS 3 and after that it does not boot into WIn 2K .
I get the menu asking which OS to boot into and whe I give the ID for Win 2K , it just returns to the menu .
Any help in solving this issue is highly appreciated .
Thanks and Regards

Thanks for the reply , but do you have any idea as to what might have screwed it the partition.
Also I don't think there is an issue with the partition , I strongly suspect the boot files would have changed though I really doubt it .
Any ideas ???
Thanks in advance .

Logical Partition Only? Windows Arch Dual Boot

ASUS Eee PC
I want to dual boot for the present time and my hard drive is currently partitioned as:
Winows - NTFS - Primary partition - 70 GB
Hidden - Fat32 - Primary partition - 15 GB
Unknown - Other - Primary partition - 20 MB
Unallocated - 147 GB
I have no idea what the hidden and other partitions are, but I don't want to delete them just yet.
This leaves me only one partition to install Arch on. Can I make the all of unallocated a logical drive and install Arch or do I need at least one primary partition?
Thanks,
Kent

There's also usually an option to make a set of recovery disks. I think I had a 12GB recovery partition and the "set" of discs was going to be 21CDs but it would free up that space and a primary partition.

Lenovo Z585 Ubuntu 13.04 / Windows 8 Dual Boot Issue - Wake from Suspend?

Similar Messages

Maybe you are looking for