Leopard and Wireless network

Ever since i've installed Leopard, when I start my Macbook the networking preferences menu starts up to ask me to create a network connection but I already have one that he recognises and that I can use.
How can I stop having to quit the network assistant everytime I open my laptop?
Thanks

Go to your system preferences > accounts > login items and make sure this is not on the list, if it is delete it.

Similar Messages

  • Leopard and wireless

    I'm having problems with Leopard and wireless. On a MacBook G4, the wireless signal dropped from 5 bars to 1 bar after the installation of Leopard. Same happened with an iMac G5 PPC. A MacBook Pro has no problems. Neither does a new iBook.
    Tried the "safe boot" mode for the two problem machines with problems. No improvement.
    Applecare noted "a few people" were having problems. The boards here show otherwise.
    Has anyone found a solution to the weak signals of Airport cards when using Leopard?

    I followed advice I found on macfixit.com and did two things. The 2nd one appears to have done the trick:
    1) in System Prefs click on Network Prefs. Highlight AirPort in the left column and click on Advanced. Now delete all the wireless networks and re-add them. Select "Remember any network..." and hit OK. That seemed to help but did not eliminate my problem, which led to step 2:
    2) Upgrade the firmware on your wireless router. I have a Belkin N1 and after 3 calls to customer support figured out which file I needed, disabled the router's firewall, and installed the new firmware. Have not had the problem now in about 12 hours.

  • G62-454ca won't turn on.power led and wireless network led keeps blinking every 3-4 seconds

    Please help.when I try to turn on nothing happens.Only power LED and wireless network led keeps blinking every 4 seconds

    According to the message you have recently posted I would like to confirm that this is a hardware issue and I strongly recommend you to immediately Contact HP Technical Support over the Phone for further assistance without any delay to get your Notebook diagnosed and serviced by an authorized HP Certified Engineer
    You can also Check your warranty Here to verify the warranty status
    Hope this helps, for any further queries reply to the post and feel free to join us again
    **Click the KUDOS star on left to say Thanks**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
    Thank You,
    K N R K
    Although I am an HP employee, I am speaking for myself and not for HP

  • DHCP Server - Different Range for Wired and Wireless Network

    We have DHCP setup on Windows Server 2012r2 and the range given to us by the main HQ is 10.65.112.1-10.65.112.254 (there are several exclusions under this range)
    Now since the range gets exhausted quickly, they provided another one 10.65.122.1-10.65.122.254.
    What our branch would love to do is to dedicate the first range for Wired Computers and the other range for Wireless Devices (Phone,Tablets, Mobiles)
    Right now we have 2 different scopes setup in DHCP, the second one is disabled. In our network we have 6 access points and also have a CISCO SG300-52 Managed Switch. It has an inbuilt DHCP Server and also has the function for DHCP Relay. But we are not actually using any of its functionality as of now.
    So my question is how to have 2 separate ranges for wired and wireless network. People have mentioned vlans but I have no clue on how to get that done.
    Is there a simpler way avoding V-LANS or if not, would love to get step by step procedure on how to go about this. Any help will be much appreciated
    Regards,
    Sheldon

    Hi Sheldon, please read this post
    https://supportforums.cisco.com/thread/2270049
    You will need some modifications though. Steps 1-6 is very relevant. On step 6, you need to pay particular close attention to the "default router". If the SX300 handles your intervlan routing then the default router needs to be the IP of your VLAN. If you have a different device to handle VLAN routing then the default router needs to be that IP address.
    -Tom
    Please mark answered for helpful posts
    http://blogs.cisco.com/smallbusiness/

  • Officejet Pro L7780 Wired and wireless networking at same time

    I have an officejet pro L7780 printer that I would like to use wired and wireless networking at the same time.  It that possible.  The printer is connected directly to the network by ethernet, but I would like to print wirelessly with an ipad or iphone using HP ePrint Home and Biz.
    Thanks,
    Maurice Hawley

    The bad news: no it is not possible to have two connections active on your printer at once.
    The good news: the router will connect any device to the printer regardless of how the printer or the devices are connected.  So your iPad can print to a printer that is wired (with Ethernet) to your router.
    If it does not work, restart your router by pulling its power plug momentarily.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Airport and Wireless network issues

    I have read all the issues about airport and wireless network. I don't see the issues that I have. My issue is that my wireless network used to automatically connect as soon as I power up my powerbook; then one day I power up and I was connected to default and I did not see my wireless address listed. I when into airport setup to try and setup again and it would not let me saying my password was not right. I logged off and then on again this time my network address was listed, but it still would not connect automatically to the network, now everytime I go to the web I must pick my own network and put in a passwork that sometimes works and sometimes not.
    I have not done any updates or put any new software on the powerbook, so this is not the reason for my problem.
    Please Help!!!
    Thank's
    La Vern
    G4 Power PC 15in Alum   Mac OS X (10.3.9)  

    Had this issue with our imac after upgrading to 10.4
    The answer was to go into Network and select airport tab.
    Listed there (for me) were three settings. Delete all of them ,they will probably include the actual network you want! Click to apply. Re-start the Mac.
    Go back to network and airport and you should now see only the network you wish to join. It will ask for passwords again!!
    Click apply and restart. It worked for me.

  • Upgrade to Leopard = No Wireless Networking

    Hi,
    I upgraded my Mac Mini (1.83 GHz Core 2 Duo) to Leopard the other day. Took it to 10.5.2 right after the upgrade.
    Everything worked flawlessly for about 2 days.
    Then the AirPort networking started dropping it's connection. I have a Wireless Router setup right beside the Mini which it now just barely picks up (1-2 bars) and drops the connection every few hours.
    And I can no longer browse / see any of the other wireless networks in my neighborhood.
    My MacBook which I also upgraded to Leopard is working fine. Full signal strength and can see the 5-10 other networks in my vicinity.
    The Mac Mini was also working perfectly fine before I upgraded to Leopard.
    I tried deleting the com.apple.airport.preferences.plist as some posts suggest but that doesn't work. There seems to be other Mini owners with similar problems but no solutions.
    I don't want to revert to 10.4 ... any suggestions?

    Have a look at the thread at http://discussions.apple.com/thread.jspa?threadID=1506687&tstart=0 for some additional comments regarding this issue, and a commentary from macfixit.com relating to it.

  • Problem with Skype and Wireless Networks

    I have been having a problem with Airport for about 10 months. Long winded explanation follows.
    Initially file transfers over wireless networks were extremely slow but this seems to have been that 10.5.2 update problem. There is a remaining issue when I use Skype on my Mac (details below) connected to a wireless network the incoming and outgoing audio drop out for 1 - 3 seconds at irregular but frequent intervals (approx every 5 - 10 seconds). This is regardless of the wireless network I am on - and that is dozens of them all over the world. Note it is voice only calls, not video. Apple has replaced the Airport card and the mother board; the OS has been reinstalled; test accounts set up but nothing fixes the problem.
    At one point I had temporary relief by switching off 'Configure IPv6' in System Preferences/Network/Airport/TCP/IP. This worked for a month or so but now the problem is back as before.
    All other aspects of wireless activity are fine. Wireless firmware is 1.4.4.
    I have worn out my welcome with the usually sensational help desk. Any suggestions out there in Mac Land?

    Hi there
    Been a hectic week here getting this problem resolved. It is all OK now. Here is what we found and how it was done.
    When Airport was playing up we set up an unlimited ping of the wireless router in the office. This is what it showed:
    PING 10.10.10.1 (10.10.10.1): 56 data bytes
    64 bytes from 10.10.10.1: icmp_seq=0 ttl=255 time=1929.885 ms
    64 bytes from 10.10.10.1: icmp_seq=1 ttl=255 time=929.788 ms
    64 bytes from 10.10.10.1: icmp_seq=2 ttl=255 time=2.633 ms
    64 bytes from 10.10.10.1: icmp_seq=3 ttl=255 time=1.845 ms
    64 bytes from 10.10.10.1: icmp_seq=4 ttl=255 time=1.941 ms
    64 bytes from 10.10.10.1: icmp_seq=5 ttl=255 time=1922.656 ms
    64 bytes from 10.10.10.1: icmp_seq=6 ttl=255 time=922.724 ms
    64 bytes from 10.10.10.1: icmp_seq=7 ttl=255 time=2.012 ms
    64 bytes from 10.10.10.1: icmp_seq=8 ttl=255 time=1.974 ms
    64 bytes from 10.10.10.1: icmp_seq=9 ttl=255 time=2.283 ms
    64 bytes from 10.10.10.1: icmp_seq=10 ttl=255 time=1918.448 ms
    64 bytes from 10.10.10.1: icmp_seq=11 ttl=255 time=919.372 ms
    64 bytes from 10.10.10.1: icmp_seq=12 ttl=255 time=2.609 ms
    64 bytes from 10.10.10.1: icmp_seq=13 ttl=255 time=2.037 ms
    64 bytes from 10.10.10.1: icmp_seq=14 ttl=255 time=2.259 ms
    64 bytes from 10.10.10.1: icmp_seq=15 ttl=255 time=1921.022 ms
    64 bytes from 10.10.10.1: icmp_seq=16 ttl=255 time=920.825 ms
    64 bytes from 10.10.10.1: icmp_seq=17 ttl=255 time=2.416 ms
    64 bytes from 10.10.10.1: icmp_seq=18 ttl=255 time=2.063 ms
    64 bytes from 10.10.10.1: icmp_seq=19 ttl=255 time=1.954 ms
    64 bytes from 10.10.10.1: icmp_seq=20 ttl=255 time=1917.649 ms
    64 bytes from 10.10.10.1: icmp_seq=21 ttl=255 time=917.617 ms
    64 bytes from 10.10.10.1: icmp_seq=22 ttl=255 time=2.018 ms
    64 bytes from 10.10.10.1: icmp_seq=23 ttl=255 time=2.057 ms
    64 bytes from 10.10.10.1: icmp_seq=24 ttl=255 time=2.106 ms
    64 bytes from 10.10.10.1: icmp_seq=25 ttl=255 time=1916.329 ms
    64 bytes from 10.10.10.1: icmp_seq=26 ttl=255 time=916.347 ms
    64 bytes from 10.10.10.1: icmp_seq=27 ttl=255 time=2.020 ms
    64 bytes from 10.10.10.1: icmp_seq=28 ttl=255 time=2.151 ms
    64 bytes from 10.10.10.1: icmp_seq=29 ttl=255 time=2.005 ms
    64 bytes from 10.10.10.1: icmp_seq=30 ttl=255 time=1915.818 ms
    64 bytes from 10.10.10.1: icmp_seq=31 ttl=255 time=915.821 ms
    64 bytes from 10.10.10.1: icmp_seq=32 ttl=255 time=2.091 ms
    64 bytes from 10.10.10.1: icmp_seq=33 ttl=255 time=2.061 ms
    64 bytes from 10.10.10.1: icmp_seq=34 ttl=255 time=2.064 ms
    64 bytes from 10.10.10.1: icmp_seq=35 ttl=255 time=1911.739 ms
    64 bytes from 10.10.10.1: icmp_seq=36 ttl=255 time=911.753 ms
    64 bytes from 10.10.10.1: icmp_seq=37 ttl=255 time=1.923 ms
    64 bytes from 10.10.10.1: icmp_seq=38 ttl=255 time=2.788 ms
    64 bytes from 10.10.10.1: icmp_seq=39 ttl=255 time=1.911 ms
    64 bytes from 10.10.10.1: icmp_seq=40 ttl=255 time=1907.626 ms
    64 bytes from 10.10.10.1: icmp_seq=41 ttl=255 time=907.528 ms
    64 bytes from 10.10.10.1: icmp_seq=42 ttl=255 time=1.847 ms
    64 bytes from 10.10.10.1: icmp_seq
    and so on.
    After discussion with tech support they said the Airpot card had to be replaced. This was done with admirable expediency and I got the MBP back in 36 hours. On testing it the same problem was still there. Identical pattern on the ping test, the fault was not the hardware.
    Once more a call to Apple and another tech. This time we booted from the OS 10.5 install disk and ran the ping test. I ran it for a few hours without seeing the fault, it worked fine. The problem had to be in the operating system.
    After backing up all the data I zeroed the drive and did a clean install of the OS. Bingo! Problem gone.
    So after 10 months, two airport cards and a mother board, the issue was in fact something corrupt deep in the OS.
    So to anyone having similar problems with Airport, run a ping test as described above. If you see that kind of pattern, try a clean install before going down the hardware road.

  • How to set up an integrated wired and wireless network

    I have an iMac 17" 1GHz connected to a ethernet hub which in turn is connected to a DSL modem and from there to my ISP. I also have a MacBook Pro wirelessly connected to an AirPort Express; the AE is connected to the same ethernet hub through its ethernet port.
    I can connect to the Internet wirelesly using the MacBook Pro, but I can not seem to connect to the iMac.
    How can I keep the iMac wired and the MacBook Pro wireless, but see both on a network? The AE instructions don't seem to have an example for this kind of network.
    Any help would be greatly appreciated!
    Cheers,
    Martin
    MacBook Pro   Mac OS X (10.4.6)  
    MacBook Pro   Mac OS X (10.4.6)  

    Martin,
    As Frank said, you'll need a router with DHCP and NAT abilities (nearly all have this) connected to the modem.
    But just in case your "ethernet hub" is actually a router, just re-configure the AE not to distribute IP addresses - AirPort Admin Utility - Network tab. Try that and let us know.
    For minimal clutter, if you were DSL broadband instead of cable, you could sell the modem, sell the ethernet router, sell the Airport Express and buy a single Ethernet and Wireless DSL modem router - for less than the price of the AE. Some people like to keep the modem separate to make upgrades to the modem cheaper. My solution is to buy a decent modem in the first place, ie make sure it has ADSL2+. Almost all modem/routers do this now, even my ancient ones have firmware upgrades to offer this.
    For minimal spend, you can pick up an Ethernet router for about $30. Just replace your ethernet hub with it.

  • Snow Leopard and intermittent network

    I upgraded to Snow Leopard a couple of weeks ago, and now have 10.6.1. I also have Comcast for my internet service provider.
    I have three Macs, and a couple of PC's, all connecting on my network through an Airport Extreme. All software settings (on the Macs) are up to date.
    When I first installed SL, everything seemed fine. Now, I have a problem where every 20 seconds or so, the network connection drops. This is on at least two different Macs. (Both with SL.) When I run Network Diagnostics, Airport & Airport Settings stays green, but Network Settings, ISP, Internet, and Server fail. When I run network diagnostics from Safari, I go through its steps, and the network connection immediately comes back on line. After a few seconds (about 20 or so), the Network Settings, ISP, Internet & Server fail again. So, I can load one or two pages at most, then the network fails again, over and over.
    I reset my modem for Comcast yesterday, and the connection seemed better, and I had hoped it was fixed. However, this morning it started constantly losing the connection again.
    Any ideas?

    Deb,
    Thanks so much for your help. Unfortunately, I've been out of town, so took a break on trouble-shooting this. I just got off the phone with Comcast, and apparently they "upgraded" something, which is breaking a lot of routers. Consequently, I'm thinking my Airport Extreme may no longer be compatible with Comcast's modem.
    When I plug directly into the modem, I don't seem to have as many issues, although occasionally I can go a long time without having problems with the connection, through the Airport as well. When I'm using my Airport Extreme, I may have perfectly good connection with one computer, but dropping the connection all the time with another. Right now, my iMac is working fine (through the Airport Extreme), but my MacBook is constantly dropping connections also through the Airport Extreme, so I have to use Network Diagnostics every time to load even one page. The computers are sitting next to each other, very close (less than 1 foot) away from the Airport Extreme. I have also experienced this problem with my iMac, so its not actually computer specific. Also with an iPhone and iPod touch.
    The comcast tech was (naturally) quite useless.
    So, I'm not sure what might fix this problem. Perhaps it is getting a different phone/internet service!!! (The ibuprofen is not helping much either!!)
    I've done some speed tests, and the speed for the connection looks great.
    Any other thoughts???
    Thanks so much for any suggestions!!!
    Laurie

  • Wired and wireless network setup

    I have a small home network, wired right now. I would like to add a wireless access point for near future laptops. Can I add a second router that is wireless to my wired network with having to load router software on a second computer. Is this even possible. My network consists of my PC, HP M8300f desktop PC as home base/client and cable modem with linksys wired router, BEFSR41 connected to a dell 2400 desktop. I am wanting to add a linksys wireless router WRT54G some where in the living room for and access point. Do I have to load the software on the Dell PC or can I just plug in router to wall socket and connect wirelessly that way. Thanks for the help. Just thinking out side the box.
    OS Vista Home Premium 32 bit
    CPU AMD Athlon 64x2 6000+ 3.0ghz
    Motherboard Asus M4N78 Pro
    Memory 3Gb PC2-5300 DDR2 @ 667mhz
    Graphics Card BFG Nvidia Geforce 8400 GS 512MB DDR2
    Monitor(s) Displays HP W1907 LCD 19", Gateway HD 19" LCD
    Antec Earthwatt 80 plus 500 watts
    Hard Drives 640GB 7200rpm SATA (2x320)
    Other Info Optical: Super Muliti DVD burner w/lightscribe, Hauppauge WinTV HVR-1800

    You can add your WRT54g to your wired network without too much trouble if you follow a couple of simple steps:
    Turn off the DHCP server in the wireless-router.
    Create an unique wireless network name (aka SSID) and turn on WPA-PSK security.
    Make sure the web-page IP address for the wireless-router is set to a unique value different from any of the other wireless devices on your network.
    Connect the LAN port of the wireless-router to the LAN port of the Ethernet router.  Do not connect to the wireless-router's WAN port.
    This configures your wireless-router into a simple Access-Point and is the easiest way to extend your home network with wireless.
    Best Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • Using a wired AND wireless network on one machine for better security

    It occurs to me that if I could separate my Internet traffic from my LAN traffic, I could have the best security setup, so that machines on my network would only have file sharing enabled for the WIRED connection and I would use the Internet over the WIRELESS connection.
    How do I configure my PowerBook and Mac Mini to do this? In the Sharing preference pane, it doesn't allow me to specify which network port the sharing will be active on.
    And once I am conncected to both a wireless and wired network, giving each machine 2 IP addresses, how does the computer know to route the IP addresses to the right port?
    I'm using an Airport Extreme Base Station (connected to a cable modem) configured to distribute IP addresses to the wireless ports on the computers for Internet and a Linksys router distributing IP addresses to the ethernet ports on the computers with sharing turned on.

    in the Thinkvantage Access software, you can set the network preferences. So you can set the Ethernet to be your most preferred network connection method, while your wireless as the second most preferred method. Or which way you prefer.
    So for example, when you dock and the computer detects the ethernet network connection, it will automatically switch to the ethernet as it becomes available. And when you undock, your computer will switch back to wireless as ethernet is not available.
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • A very strange wired and wireless network issue

    Hello,
    I have never had any issue at all with my macbook (2008) until this week, I use it both for work and personal use.
    Most of time, I'm used to be on customer site, so I use wired and wireless connections depending of the situation....
    I have never had any issue at all with wifi neither ethernet connections during three years, until this week... and I can say this is the most strange thing I have ever seen....
    Using wired or wireless connection, always the speed of network was really good, at home, many customers, etc never had any problem...
    But this week I'm currently out of home, and the hotel where I'm staying I'm having very poor network rate....
    Using wireless connection, the download speed is no more than 10kb.... and using ethernet I get less speed... but during the day I'm on customer site, using the ethernet connection and download speed is really good, more than 500k-800k....
    I have already tried in the hotel few wifi connections (there are three) and differents wired connections (in diferent rooms) and the download speed is always the same, no more than 10kb...
    During this afternoon, I could go into hotel's lab and could connect directly to the router using cable, same speed no more than 10kb....
    The most strange thing is on their computers the download speed using wired connection is around 6Mb....
    how is possible I'm getting no more than 10kb of download speed when the pc's at hotel using same wired connection gets 6Mb?
    I have already deleted current network connections, execute onyx to clear everything, perform dhcp connection, tried manual ip etc, and always the results are the same...
    I know there is no problem with the macbook, because it works pretty good at every location I've been... but until this week...
    Sincerely I'm getting a little crazy here, I'll appreciate any help!!!
    thanks in advance

    I've seen something like this on my T400 when it was running Vista.  Now that I use Win 7 it's been OK. I rather doubt that your issue is the same but I'm tossing it out here just on the off chance.
    Im my case, I had to downgrade my Intel 5300 card to a 5100 (as suggested by a Lenovo 2nd-tier tech) to get things working.
    My symptoms were a little different.  Wifi was fine until I went back to a wired network.  After that, trying to use the same wifi AP as before would end up associated, but no internet access.  DHCP wasn't working.  The GUI "find" app didn't work as expected either.  Some APs showed up, and some didn't.
    If I configured for automatic connection to my home AP it would try and fail.  Just rebooting at that point would again attempt an automatic connection that would succeed.
    What I have noticed now that I run Win 7 is that Access Connections is completely useless.  Often the "finder" doesn't show an AP 3 feet away.  I didn't notice that this happened after a switch from wired, but maybe.
    Are you using Access Connections?  If so, you might try uninstalling it.
    Sorry I can't be of real help,
    Z.
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Serious issue with Mac OS X 10.6.4 and wireless networking

    Hello there, I'm having a serious issue with my TP-Link WP-8910G wireless router and Mac OS X 10.6.4 .
    Problems began some days ago. In short, after a certain period of time, my router drops the wireless connection out and, when I try to re-establish it, if a very short period of time has passed after disconnection Airport detects the wireless network and returns "connection timeout". If I wait more, no wireless connection is detected, and I have to reset the router and re-connect Airport. This is very annoying.
    How can I solve this issue?

    Have you verified that the router is not the problem?

  • Having issues with Snow Leopard and wireless

    I've read the many threads and articles on issues with SL and dropping wireless, but still can't resolve the issue. Can anyone point me to some new articles on the issue?
    I'm able to get online no problem with no drops with my iphone, I have the following:
    linksys cisco wrt54G2 wireless router
    Mackbook white intel
    The issue is that I'm dropping the ISP/Internet/Server in Network Diagnostics every 5-10 minutes and have to sign on again. I've tried a few things to no avail.
    Thanks for any help.
    Thanks.

    Hi!!
    I just received my first Macbook yesterday and have been having the exact same problem as you with internet connection. This morning I browsed Apple´s support website and found an article that addresses wireless connection and I really think it may help. I haven´t tried it yet because I don´t have my MBP here with me but it´s so simple I believe you should give it a try!
    Below is a copy of the article that I found
    : http://support.apple.com/kb/TS2098
    If that one specifically doesn´t help, there are other helpful articles in this page: http://www.apple.com/support/airport/
    I really hope that helps, I know how frustrating it is not being able to stay connected! Best regards,
    Renata
    AirPort Express: Difficulty joining third-party network that is using WEP
    Last Modified: October 21, 2008
    Article: TS2098
    Old Article: 300153
    Symptoms
    Joining the network of some third-party wireless access points requires a little special treatment when the network is protected by Wired Equivalent Privacy (WEP), an older wireless security protocol.
    Products Affected
    AirPort Express Base Station
    Resolution
    First be sure that the third-party access point is not restricting clients based on MAC addresses (sometimes called an access control list), and be sure that the base station has the latest version of firmware that's available from the manufacturer's website.
    Next, beware that WEP passwords can take either a plain language or hexadecimal form, as described in joining an encrypted wireless network. You might be able to avoid password issues entirely by changing the password of the WEP-protected network to a better format.
    Using that information, you should try connecting an AirPort-enabled computer to the WEP network to verify what will be required. If you have to enter a hexadecimal value to get the computer on the network, the same will be true for AirPort Express.
    Confirm that you are running Mac OS X 10.4 or later or you have the AirPort 4.0.1 update installed. Open AirPort Utility, and go through the steps to set up AirPort Express to join your existing network. When you get to the page where you select the wireless network the AirPort Express is to join, you will see two password entry fields. If a hexadecimal password was required to get your AirPort-enabled computer on the network, use the same hex code here, but add a "$" in front of it.
    So if your hex value is "6170706c65", you would enter "$6170706c65".
    Finish the steps in the Assistant. Once the AirPort Express has had a minute or so to restart, it should join the network and once it finishes rebooting (allow up to a minute) it should join the existing wireless network, as indicated by its status light.

Maybe you are looking for