Leopard does not recognise second scanner

I have 2 scanners connected to my Mac Mini, an Epson V700 and an Epson CX3650.
Under OSX 10.4 when starting Epson Scan I was presented a list of scanners where I could chose from and both scanners could be operated.
After upgrading to Leopard and installing the new drivers from Epson, Leopard only recognises the Epson V700. The CX3605 is an All-in-one and the printer works fine under Leopard.
If I only install Epson scan for the CX3650 it works fine.
How can I get both scanners recognised by Leopard?

Have you checked Epson's website for new drivers?
I had to reinstall the drivers for my Canon scanner for it to work properly.

Similar Messages

Since upgrading my Macbook pro with Yosemite, I have problem with my Xerox Work Centre 3045 - the printer works normally but it does not recognise the scanner, can you help with this?

Since upgrading my Mac book pro with Yosemite, I have problems with my Xerox Work Centre 3045 printer. The printer works normally but it does not recognise scanner, I can not scan anything. Can you help?

Open Disk Utility and select your hard drive, then Repair Permissions, it will probably return a very large number of errors, primarily printer and library errors, so run it a second time. Then restart the MacBook Pro. If it still will not scan, try using Image Capture from Finder > Applications and see if that will work. If not, contact Xerox about updated drivers.

Solaris 8 does not recognise second CPU

Hi,
my Solaris 8 installation on my E250 does not recognise my second CPU. prtdiag and psrinfo only show one CPU. OBP reports the second has no problem and is online (ASR). It even has the same temperature as the other operating one...
Can someone help me?
Thanks in advance to all,
Horst

# eeprom
check the .upa-noprobe-mask variable. It has to be 0 to see all cpu's
depending on OBP revision, it may be called upa-noprobe-list
# eeprom .upa-noprobe-mask=0
# init 6 (to reboot)

I've upgraded to Mavericks. HP Scan no longer works to scan images from an HP Photosmart c309a yet the printer works. My Mac does not recognise this scanner as a scanner, only as a printer. How do I get my applications such as Preview to use this scanner?

I've upgraded to Mavericks. Formerly HP Scan we used to establish communications with an HP Photosmart c309a all-in-one printer/scanner on my wi-fi network. As of the Dec 2013 update to Mevericks, it appears that HP Scan is now disabled and I cannot find this device as a scanner in System Preferences. I cannot connect to it in either Preview, Pages, or Photoshop Elements 8. Does anyone know a way of getting the OS to recognise this as a scanner?

How was the printer added? Using AirPrint or the HP ppd? Since Mavericks defaults to adding an AirPrint printer with the AirPrint ppd, it might be necessary to add it again with the HP ppd, after making sure you have the HP drivers installed.

Leopard Does Not Recognise My Password - Help!!

I am not a computer-techy so I need some simple help.
Yesterday I upgraded from 10.4.9 to Leopard 10.5. My iMac no longer recognises my Administrator's password which means that I am barred from properly using my computer.
How do I fix this? I have seen responses on other similar topics but they are so technical they go over my head.
I have never, in 7 years of using Macs, had such a problem before.

Hi Julian,
+If I go to Macintosh HD then Places there is a house logo with 8 lower case letters against it which are the first 8 letters of my user name. Is that my short name?+ Yes as far as I know
+I am confused by the username bit. I realise that I replace that with my short name (whatever it might be) but what goes either side of it?+ Nothing
+Under note 5 it looks like: Users/shortname AuthenticationAuthority. (no space after /, space after shortname).+ Correct
+Under note 8 it looks like: passwd shortname. (space after passwd).+ Correct
As an alternative do you have another account on the machine you can access as there is a keychain fix now available on the apple web site which if you can install via another account might work. http://www.apple.com/support/downloads/loginkeychainupdate10.html
Message was edited by: Orangeboot

Please help. ive bought a second hand ipod nano, when i connect it to my pc it recognises it as a sigma mass usb device, yet its a 8gb ipod nano,and i tunes does not recognise it, im running on windows vista basic yet my own 80g classic ipod runs perfect

please help. ive bought a second hand ipod nano, when i connect it to my pc, it does not recognise it in itunes,yet it comes up as a sigma mass usb device. its an ipod nano 8gb?. im running on windows vista,my own ipod classic runs fine.

there is a good chance that this can be related to bad contact in USB lead.. e.g not enough power from IPOD to PC so that pc cannot recognise it. Where I work I get alot of USB devices on pc's that are not recognised and most of the time it is the connection to the device that is not good enough because the flat end of the USB adapter has been gradually bent over time just slightly and now contact is not good. It can also be todo with drivers or If you are using it through a USB hub.
so if it is not working through USB hub try direct. also try in back of PC as these Ports or direct access to main board to pc and would be less trouble some if there was a voltage loss from mainboard in pc to front of unit.

Photoshop does not recognise scanner

Hello
Photoshop Elements 10 does not recognise scanner that works correctly when used directly.
How can I solve the problem?
Best regards - Studi1

Hello hatstead
Thank you for your tip. It did not work out.
- You indicate the folder name for the TWAIN plug-ins to be moved.
-- The name corresponds to PhotoShop Elements 9.
-- I am working presently with PhotoShop Elements 10. And the name seams not to correspond.
- Do you have a hint how to solve the problem?
Best regards - Studi1

IPod Nano: Error Message "The USB device has malfunctioned and Windows does not recognise it"

Hi everyone, I just received 2 brand new iPod Nanos for my kids for Christmas, thought I'd be smart and sync them both now before wrapping them so I don't have to be messing around with them on the day. One synced without a problem, then using the same cable, same computer, same USB port, the 2nd one came up with "The USB device has malfunctioned and Windows does not recognise it" I've tried restarting my computer, unplugging and reinserting the USB. Is there anthing else I can try before returning it? Thanking you for any help.

I have solved my problem, I ended up ringing Apple and got an awesome lady who told me to reset it by pressing the sleep button and menu button together for about 10 seconds and once it actually turned on for the first time the computer then recognised it, so it's all good, :-) Thank you lovely lady!

I have a 16GB iPhone 3GS. Tried synching my phone through iTunes (11.0.1 I think... on a 2009 Macbook Pro). Now when I connect to iTunes, it says it does not recognise the content on my phone. Is this because my phone (and laptop) are too old?

I have a 16GB iPhone 3GS. Tried synching my phone through iTunes (11.0.1 I think... on a 2009 Macbook Pro). Now when I connect to iTunes, it says it does not recognise the content on my phone. Is this because my phone (and laptop) are too old?
Also, when I tried to Restore the settings, an Error Message pops up that says " The iPhone software update server could not be contacted. The requested resource was not found.
I'm trying to free up space on my phone by removing [literally] thousands of old photos which were originally synched to the phone, because I had forgotten to uncheck the photos button when I synched it ages ago.
I have also tried synching it on my 24" iMac (running OSX Snow Leopard). But again, when I try restoring the phone through itunes, it says the file is corrupted. It sggests unplugging the device, and then plugging it in again. I have done this numerous times with no success.
I'm guessing it must be because my phone (and versions of iTunes, and OSX) are all too old.
Please can anybody help.
Cheers,
Dan_nz.

There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support

Now have OSX 10.8.2. cannot update my HP Scanjet software. Have downloaded a patch from the HP site, but my MacBook will not open it as it says it does not recognise HP as an apple compatible compnay. Any advise?

I have just plugged in my scanner (HP Scanjet G2710) however my old HP Scan software will not opne. I have found a patch on the HP site which may fic the problem (although it only sesm to go up to OSX 10.7) and having donaloaded the patch my Mac will not opne or deal with the software as it now tells me it does not recognise HP as an Apple affiliated compnay. Any help / suggestions? I don't really want to buy another scanner...

Hi,
By reading your notes I assume you didn't uninstalled the HP Software and installed the latest v10.6 software available online, any previous version will not work regardless the patch installation as it was not signed.
Be sure to follow the directions listed in here:
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c03428470 #A3
The latest software can be downoad from here:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en &cc=us&prodTypeId=15179&prodSeriesId=3423844&prodNameId=3423845&swEnvOID=219&swL ang=8&mode=2&taskId=135&swItem=sj-78355-5
Then you should reinstall the patch:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en &cc=us&prodTypeId=15179&prodSeriesId=3423844&prodNameId=3423845&swEnvOID=219&swL ang=8&mode=2&taskId=135&swItem=cs-97791-1
Hope that helps,
Shlomi

My i pad shows connect to itunes but my computer does not recognise the devise -- it was ok until i tried to do a software update

my i pad shows connect to itunes but my computer does not recognise the devise -- it was ok until i tried to do a software update

Try and force iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Aperture does not recognise TIF files from Nikon CoolScan

The TIF files from my Coolscan are good in every other application, but Aperture does not recognise them. I've tried re-saving the TIFs as JPG and PDS but Aperture doesn't recognise any file generated from the TIF. Maybe it's something to do with the scanner driver? Any ideas how to load these files into Aperture?

You might check the color space that is assigned to the files. If you are using Nikon Scan software to manage your CoolScan, there is a preference for setting the color space of the saved file. FWIW, Nikon CoolScan .nef files are a 'raw' file, not camera raw, that was/is a Nikon proprietary format for their scans. If you use the Nikon Scan for image editing, the edits are non-destructive in saved files and can be adjusted by re-opening the file in NS. Adobe first made editing camera raw available in early 2003 and the Nikon format preceded that. Nikon's camera raw format also has the .nef extension, but is not the same as the CoolScan .nef-- really confusing. I suggested checking the color space, because Nikon has different internal names for Adobe RGB(1988) as well as their own Wide Gamut space.
All said, I've not had a problem opening .tif scan files in Aperture.

CS5 Bridge does not recognise Nikon D 800 Raw Files

I have Photoshop CS5 Version 12.0 (x64). Photoshop recognises Nikon D 800 Raw files BUT
Bridge does not. I have tried updates but my Apple Mac Pro does not recognise them

That would mean that you have the ACR plug-in version 6.7 or 7.1 in the wrong place.
You can only have one version of ACR anywhere in your installation. If you have two, it won't work. Look for the version(s) you have installed in Photoshop under the Photoshop menu > About Plug-In:
Your camera has been supported ever since ACR 6.7 and CS5 can run ACR 7.1 (but not any higher version of ACR).
The only correct path for the plug-in in CS5 is as follows:
Very wide image: click on thumbnail for larger view.
NOTE that the path starts with the ROOT LEVEL Library, the one right after the name of your boot drive, not your user or Home Library.
The screen shot is from an installation under Snow Leopard, where I had CS5.

MDS9148 does not Recognise 6248 FI

Hi there
I cannot get an MDS 9148 to recognise and push zoning to a 6248 FI.
I have an MDS9148 (6.2.3) connected to a 6248 FI (2.1.2a). I am using DCNM 6.2.3. I only have the base port license on the MDS, and the free version of DCNM. My reading of the documentation suggests that with that suite of product I should be able to see and manage the 2 SAN elements of the MDS and FI (zoning etc etc) from the DCNM.
I have configured the FI in Switch mode, I want the MDS to do the zoning for both devices.
I have link up on the ports between the FI and the MDS. There are 2 ports, configured as a port channel.
I have an EMC SAN connected to the FI. It is visible to the MDS.
I have an operational blade in the chassis. The MDS can see that too.
So the DCNM shows the whole network, but does not recognise the FI as a 6248, and so it will not allow me to configure and manage my zones across the 6248 either.
I have attached showing the view of the network from fabric A and Fabric B sides.
Any thoughts would be appreciated
Anthony

calopez2
Thanks for that tip. I had an SNMP user "dcnmuser", in the UCS, but not a local admin user. Once I did that I was able to discover the Fabric and have the ability to pick the Fabric or the MDS ports for zoning purposes. That is certainly an advance!
I seem to be 2 steps forward and 1 step back though. I have 2 other issues.
1. when I edit the zone and add some of the SAN ports into the zone, I can select either the fabric or the MDS SAN Switch A, connected to Fabric A (so far so good), I can select the ports I want (I will use WWNN later, but for now I am using port zoning), but when I apply I get an error
"SNMP: zoneMemberRowStatus.10.1.1.3:Permission denied or feature disabled- MP001-SANSW01 zoneMemberRowStatus.10.1.1.3 Failed to add 1 members out of 1"
2. I have 2 FIs and 2 MDSs. I cannot see the same thing on fabric B (MDS and FI) as I see on fabric A. I have reviewed the configs on the 2 MDS units. They appear to be identical. However, if I do a Discover on the second MDS, it takes a very long time, and if I try to discover the B FI, on its specific address, it is successfully discovered, but then a
"192.168.25.86 has already been discovered as Fabric_MP001-SANSW02. The original SNMP credential will be used and the version checking is skipped"
If I look at License Assignments i see 4 switches, the 2 MDS 9148s and the A 6248 with correct model numbers, and the B 6248 "Switch model unknown". For some reason the B fabric is behaving differently from the A fabric. I expected that I would be able to do the same thing on both sides.
Anthony

Facebook does not recognise iMovie file type

Hi all. I have successfully downloaded videos to Facebook this year, but have just upgraded to Lion from Snow Leopard and something appears to have changed.
When I try to "Share" onto Facebook, the Facebook interface does not recognise the movie type. I also notice that instead of each project showing in the "Movie Events" file as a thumbnail of the opening frame, it sits as an iMovie Icon, albeit with the project name.
I have successfully uploaded to Vimeo, so my question is: has something changed in iMovie after the upgrade to make the "project" indigestable to Facebook?

GR-Blitz,
You can see a few ways of doing it in this thread:
https://forums.adobe.com/message/6474423#6474423

Leopard does not recognise second scanner

Similar Messages

Maybe you are looking for